Search Documents

Real economic growth for 1988 may fall short of the 3.3% projected by the Department of Commerce in August 1988 because the summer drought and intense heat in many areas curtailed output more severely than expected. The economy grew at an average annual rate of 3.0% for the first three quarters of the year, slowing in the second and third quarters. Export growth, which occurred even as the dollar edged up compared with other industrial country currencies, was an important factor in the expansion. Notable gains were posted in sales of machinery, computers, aircraft, chemicals, and telecommunications equipment. Imports increased, but not as much as exports, and the U.S. trade position was still much improved from that of 1987. Personal consumption expenditures grew slightly faster than the economy as a whole. Purchases of consumer durables showed notable strength in the first half of 1988, but slowed down in the third quarter. Despite the moderate rise in interest rates, business spending for new plant and equipment also rose and contributed to 1988 gross national product (GNP) growth. Both new business investment and export demand spurred orders for U.S.-made machine tools. Orders for machine tools for the first 8 months of 1988 were almost triple those in the corresponding period in 1987.

Jan 1, 1989

By T Hughes

Upward pressure on all mining operations is coming from the triple bottom line. To some extent this is being offset by the rise in mineral prices, but this may or may not continue. The other serious issue facing all companies is the replacement of economic reserves as exploration levels over the past decade continued to decline in line with falling mineral prices. In order to underpin the sustainability of the mining industry it is necessary to continue to reduce cost, reduce the mine environmental footprint, whilst increasing community benefit. At the same time it is imperative that we increase the economic reserves. The highest risk is in adding new mineral discoveries as the strike rate for economic discovery decreases. Gekko Systems Pty Ltd recognises that the most simple and risk averse route to increasing economic reserves is to reduce cut-off grade in the mine, thereby bringing formerly uneconomic reserves into the economic category. We have been developing a new process flow sheet which embodies the triple bottom line and the issue of economic replacement of reserves. This paper describes this flow sheet and presents four examples where this concept is/can be applied to bring about triple bottom line benefits. Sustainability can only be assured if we are the ones in control of our environment, costs and reserves.

Jan 1, 2007

By D. K. Uko

In the stretch-bend or bending-under-tension test, a strip is rigidly clamped and restrained at each end and bent by central transverse loading using a radiused punch: The strip deflection at failure has been used as a measure of formability for high-strength low-alloy (HSLA) steels by other investigators. In this work, a detailed study is made of strains developing during stretch bending of an 80,000-lbf/ in 2 (552 MPa) yield stress steel using different punch radii. It is shown that toward the end of the process, the bending strains at both the inner and outer surfaces are tensile and suddenly increase at a rapid and approximately equal rate. The strain ratio in the failure region departs significantly from plane strain , even using a large width-to-thickness ratio of about 10. The effective fracture strains appear to be independent of bend ratio (punch radius/thickness) and significantly below the fracture s train in simple tension. Metallographic and tensile data were obtained for the subject material and, for one bend ratio, the effects on stretch-bend parameters of annealing both on this material and a. carbon steel were compared.

Jan 1, 1977

By Román Tejada R

El presente trabajo señala los resultados del sostenimiento de labores subterráneas a través del proceso de pre-inyecciones e inyecciones de contacto y consolidación. De acuerdo a este estudio, se encontró que la mina San Vicente contiene estructuras denominadas "Brechas de Colapso", compuestas de material suelto y deleznable que originan un problema en el laboreo minero. En este sentido, se busca un método que se adecúe a estas estructuras como el "Inyección de cemento"donde no se requiere de muchos aditivos.

Nov 8, 1984

By Samuel A. Reipas

Introduction The ore mining industry has been successful because of technological progress and huge sums of capital investment. But new technology and plants have not come cheap. The problem now is companies will run out of money before they run out of ideas. Survival Strategies Industry survival strategies demand restructuring and new plans. Inland's prescription for the future includes: • Continued emphasis on technological improvements to upgrade pellet quality and lower costs; • Effective use of human resources resulting in employee satisfaction and improved planning and productivity; • Deliberate, well planned, and documented cost-control programs for the short- and long-term; and • Capital investments to support the first three initiatives. Technology Technological changes are not only required by the need for operational improvements, but by product quality improvement dictated by the user - usually the blast furnace operator. Established ambient measurements of pellet quality, such as tumble index, compression strength, porosity, size distribution, and chemical composition, are no longer considered meaningful in predicting pellet performance in a blast furnace. New specifications, called low temperature and intermediate temperature properties, have been recently introduced. Low temperature specifications are characterized by disintegration of pellets in the 500°C (930°F) range in the upper portion of the granular zone during the hematite-to-magnetite transformation in blast furnace stack. Intermediate temperature properties (measured by 1000°C or 1800°F) are characterized by swelling, reducibility, and compression strength after reduction, reflecting conditions in the lower portion of the granular zone of the furnace. These new parameters are being used for pellet quality evaluation at Inland, and will be introduced at its Minorca mine for more routine analysis and correlation with the pellet furnace operation. With increased emphasis on quality, effective communication between the blast furnace operator, research, and the pellet plant operator is critical. At Inland, this is accomplished through technical meetings where the opportunity is provided to solve problems, establish a common understanding on the value of quality, and develop future quality standards and programs. With the degree of sophistication in determining pellet quality as it affects blast furnace operation, the future pellet plant operator will actually be producing a custom pellet. Human Resources Technological change has been a strong point at Inland, and will continue to be. However, human resource management is equally important. Is management giving sufficient attention to employee motivation and involvement? It is a way to improve productivity, reduce costs, and enhance employee job satisfaction. The industry is beginning to understand the principles and the potential for tapping employee brainpower. The payoff can be handsome. Management has to be willing to share both information and power if participative management is to live up to its potential. It has to become more flexible and be willing to adapt to change on the human side. Management should embrace rather than fear employee involvement. Given time, joint problem solving will replace adversarial attitudes and pay dividends for both sides. Productivity and product quality will improve and new dimensions of employee job satisfaction will be achieved. But, it will not happen overnight. Attitudinal change must permeate the organization from top to bottom. This change is needed to support the working relationships and give everyone a sense of direct and meaningful involvement.

Jan 11, 1983

By D. T. Randall

The burning of coal without smoke is a problem that concerns the Government directly because of the advantages of smokeless combustion both in public buildings and on naval vessels. In addition, smoke abatement is a factor in conserving the fuel resources of the United States. Hence, as part of its general investigation of the best methods of utilizing the coals of this country, the Bureau of Mines, which is in charge of the fuel-testing work formerly carried on by the United States Geological Survey, has made extended tests to determine the conditions necessary for the smokeless combustion of bituminous coal in boiler furnaces. Bulletin 39,¢ a preliminary report, treats the smoke problem from a theoretical point of view, detailing the steps that are being taken by municipalities, manufacturers, and citizens to abate smoke, also showing the possibility of a clean city. The present bulletin not only shows that bituminous coals high in volatile matter can be burned without smoke, but also that large plants carrying loads that fluctuate widely, where boilers over banked fires must be put into service quickly and fires forced to the capacity of their units, can be operated without producing smoke that is objectionable. Proper equipment, efficient labor, and intelligent supervision are the necessary factors.

Jan 1, 1918

Book review Proceedings of the Symposium on Mining Methods. London, Institution of Mining and Metallurgy, 1974. 160 pp. The Symposium was held from 30th October to 1st November, 1974, and the papers include an interesting range of subjects in coal-mining operations, covering the improvements achieved to date, current practice, and required development for the future. Salamon, M.D.G., and Oravecz, K. 1. Rock Mechanics in Coal Mining. 119 pp. NIM reports Report no. 1822 Stability constants and linear free-energy relations for the platimtm-group metals. (22nd Oct., 1976). Report no. 1852 A revised method for the dissolution of platiniferous materials by the sealed-tube technique. (18th Oct., 1976). Report no. 1828 y-picoline adducts of the nickel, copper, and zinc chelates of 2-thenoyltrifluoroacetone. (26th Nov., 1976) Report no. 1847 A pilot-plant investigation of a kinetic model for flotation.(19th Nov., 1976)

Jan 2, 1977

By B. H. Good

This paper describes the research that has been conducted -in an effort to understand the nature and causes of sulphide fires -in the Sullivan Mine. Results of the investigation have led to several theories of the origin: of the fires, the nature of the chemistry and a method for assessing: the fire potential. Recommendations and the implications for the mining operation are also discussed.

Jan 1, 1977

On November 9, the Reynolds Metals Company cut production by 12 at its primary aluminum smelters at Troutdale, Oreg., and Longview, Wash., as a result of an earlier 25% power cutback by the Bonneville Power Administration due to lower than normal stream flow in September, the Aluminum Company of America had closed one potline at its Vancouver smelter because of the power cutback. Nearly 700 union workers at Anaconda Aluminum Company's primary aluminum smelter at Sebree, Ky., walked off the job when their contract expired or, November 15, after rejecting a proposed 3-year contract. The smelter has an annual capacity of 180,000 tons mid accounts for 50% of Anaconda's aluminum production. No talks are scheduled.

Jan 1, 1979

By Robert S. MacPhail, Chilombo Henry, Arnold Kabamba, David Mukelebai, Suresh Thirunagari, Bukali Victor, Yoram Kapai, Chomba Leonard, Kanna Amarasingham

"FLEX 31 is a chemically enhanced sodium isopropyl xanthate. Developed by Charles Tennant & Co (Canada) Ltd and has shown improved collection properties over SIPX for sulphide minerals flotation. Improvement of recoveries, grades, faster kinetics, lower dosages, high pyrite and pyrrhotite rejection capabilities have all been exhibited by FLEX 31. Recent plant trial carried out in the copper circuit at one of the largest copper mine in Zambia shown over US $ 2.00 Million annual improvement on the bottom line over SIPX at current copper prices. Data produced also showed superior grade and recoveries from rougher concentrates that previously had not been attainable with other reagents effectively. Flex 31 has also shown positive outcomes with zinc, Copper/Zinc, arsenopyrite and copper/molybdenum ores.IntroductionSodium Isopropyl Xanthate (SIPX) is one of the most popular flotation chemicals on the market today. Somewhat more specific than amyl xanthate, SIPX is used in a variety of ores like copper/zinc, lead/zinc, arsenopyrite/pyrite, and many others (Melis et al., 1991). An investigation carried out by the research division of Charles Tennant & Company (Canada) Limited has produced a chemically enhanced SIPX. This product has shown all the advantages of normal SIPX along with improved recoveries of copper and copper activated minerals. The product was named “FLEX 31”."

Jan 1, 2016

By Francis J. Fratttali, Verda McLendon, Stanley J. Green

"INTRODUCTION During the first phases of the war emergency the shortage of aluminum prompoted the Bureau of Mines to investigate methods for using low-grade bauxites of high silica content and also clays as raw-material sources of this strategic metal. The Bayer process treats low-silica bauxites to provide the industry with a major portion of the purified alumina, which contains very low percentages of silica and other impurities. One of the methods investigated in the laboratories of the Bureau of Mines for low-grade materials is the lime-soda sinter process, which was studied on a pilot-plant scale. In this process, the alumina content of the alumina-bearing minerals Bs made water-soluble by sintering the raw material with limestone and soda. Simultaneously, the siliceous material is rendered insoluble. The sinter is extracted with an alkaline liquor, and the resulting extract liquor is treated as follows to recover the alumina: (1) Autoclaving with lime to remove silica as a zeolitic complex and (2) treatment with CO2 to precipitate alumina as the trihydrate (A1203.3H20). Figure 1 is schematic flow sheet of this process.As the process is cyclic, it is necessary that nearly all of the soda and alumina remaining in the plant liquors after carbonation be recovered. Upon passing through one cycle, these liquors contain 14 to 15 percent NaCO3 2 to 5 percent NaOH, 1 to 3 percent A1203, minor amounts of silica, and, with certain materials such as Pennsylvania diasporic clays, 0.5 to 1.0 percent Na2S04. Approximately 50 percent of the Na20 in these liquors must be returned, as soda ash, to the dry-grinding and raw-materials blending operations. Previous work (6)5/ on sulfate-free solutions demonstrated that two methods for recovering Na20 were feasible, namely: (1) Salting out Na2C03.H20 by evaporation of the carbonated solutions and (2) crystallizing Na2C03.10H20 by cooling the concentrated carbonated solutions."

Sep 1, 1947

TowerMill - Advantages in Wet Grinding Applications The TowerMill, which has now been in existence for no less than 50 years, is one alternative to the horizontal ball mill and offers several advantages. The TowerMill is widely used in (coal-fired) electric power plants for the grinding of raw material for the FGD (Flue Gas Desulphurisation) process involving very high throughputs, very fine product sizes and high availability. Some companies in the mining industry also looked at the use of such optimised grinding machines several years ago and found that many of the advantages offered in other industries are transferable to new applications. Much development work has been undertaken to improve the TowerMill for new applications and, as part of that work, tests have also been conducted to make direct comparisons of their performance with that of ball mills. Grinding tests were performed using the same raw materials and comparable machine sizes. Some of the results are discussed in this paper, along with a comparison of the advantages and disadvantages. The conclusion provides an outlook for some worthwhile future applications. The test results, which are described and analysed, show that the TowerMill offers significant advantages in relation to operating costs and operational safety. An example based on the wet grinding of limestone is presented.

Sep 13, 2010

By Wagner da Silva Lima

Um Sistema Piloto de alimentação de biomassa foi instalado em paralelo ao sistema de alimentação de coque em uma caldeira leito fluidizado circulante movida a coque de petróleo na Unidade Fabril da Votorantim Metais em Niquelandia, GO. Quatro experimentos foram realizados utilizando os alimentadores de coque (limitados a capacidade de mistura da pá-carregadeira) e o sistema piloto instalado que tem capacidade de 30 m3/h de cavaco de eucalipto. A substituição energética chegou a 19%, bem acima dos 10% determinados pelo fabricante utilizando o sistema atual de alimentação de combustível na caldeira. O potencial de redução de custo do vapor varia de 4 a 7%.

Aug 17, 2017

By Louis D. Huntoon

CANADIAN gold production is forging ahead annually and the prospects are that it will continue to do so for many years. Table 1 shows recent annual increases. Production for 1933 will probably reach $70,000,000, and further increases are likely in 1934 and 1935. (Data for November and December, 1932, are estimated throughout this article.) The depression sent many prospectors to the woods so during the last two years many new gold areas have been discovered and are attracting real capital for exploration and development. Several mills came into production in 1932 and mills now under construction will start production in 1933. The offices of mining lawyers are busy. Capital for this new work is obtained from well financed mining companies, syndicates, and individuals who were fortunate enough to invest in the dividend-paying gold mines of the north country in the early days. Prospectors and capital are cooperating. An interest is always retained by the prospector or vender and usually a small amount of real money is given the prospector.

Jan 1, 1933

By Breno Totti Maia

A principal ferramenta de controle do processo BOF reside na regulagem dos parâmetros de sopro de oxigênio. As condições ótimas desse processo envolvem diversas variáveis, como vazão de oxigênio, distancia banho lança (DBL), número de furos para a saída de oxigênio na lança, entre outros fatores. Através de uma análise visual da penetração do jato e do volume movimentado, foram analisados os comportamentos para cada configuração de sopro entre diferentes combinações de bicos multifuros (3 a 6 furos), para uma distância banho lança (DBL) e vazão constantes. A análise dos parâmetros de interação entre o sopro e o banho líquido composta pelas frações de metal e escória, representados respectivamente por água e óleo de parafina é o principal objetivo deste trabalho. Foi necessário desenvolver nova metodologia para a determinação da penetração assim como proposta de nova fórmula e ajuste da constante empírica, fator K. As maiores penetrações foram alcançadas com os bicos de 3 e 4 furos. Para a configuração de 6 furos, foram encontrados os menores valores de penetração e maior volume de zonas de baixa movimentação em relação aos parâmetros estabelecidos.

Aug 17, 2017

By Fred P. Gerbracht

Jul 20, 1955

By Alastair Torrance, Mitchell Nipperess, Andrew Olsson, Italo Onederra, Gary Cavanough

Components of bulk explosive products include ammonium nitrate, water, fuel, stabilizers, and calcium nitrate. The physical attributes include prill/emulsion ratio, density, and viscosity and in the case of prilled ammonium nitrate, hardness, size distribution and fuel oil absorption. These components and attributes in conjunction with ground conditions determine all aspects of explosive performance including the risk of fume. This paper presents a fume risk assessment matrix of explosives components and physical attributes as a function of a simple description of ground conditions. Instrumentation to provide a measure of the quality of the explosive product are also described and these include both “on bench” physical measurements and laboratory analysis. “On bench” methods include “in hole “density, velocity of detonation (VOD), detonation pressure and detonation temperature. Part of the quality control process involves a mobile laboratory unit which at this stage can provide measurements of water content, ammonium nitrate content, calcium nitrate content, fuel content, prill characteristics and prill/emulsion ratio. This unit can be taken to sites to enable the testing of bulk and sensitized products at site rather than after transportation.

Jan 1, 2015

By William B. Hughes

The rubber-sleeve core barrel was developed to improve core recovery from unconsolidated sands, where it is most difficult to obtain cores with conventional barrels. The use of a rubber-sleeve core retainer, together with other departures from clsual design, has required a considerable amount of testing to prove its op-erability. Tests run in shallow experimental holes and in drilling wells in the U. S. and Vemzuela have, to a large extent, proved the operation of the barrel. Internal mechanism troubles, such as sandbinding of the sleeve, have been largely overcome. Cores have been recovered from completely unconsolidated sands where conventional coring has almost been abandoned because of poor recovery. In addition to retaining the core until brought to the surface, the barrel gives a "packaged-ar-cut" core, which is coilverzient for handling and transportatiorz. In the initial work, drag blade cutters, roller cutters, and tungsten carbide insert cutters were usrd for cutting unconsolidated sands. Further bit head development is presently being conducted using diamond heads in unconsolidated sands where shaler, hard sands, and limestones are encountered in adjacent formations. Thir work should render the barrel capable of cratting and recovering most types of formations, possibly including broken and frac- tured fornlations. This development is being carried on in cooperation with a diamond bit manufacturer. INTRODUCTIO N For many years the oil industry has needed greater recovery of cores from unconsolidated formations. Conventional equipment has been used to core unconsolidated sands with little success. Specifically, a core barrel was needed which would recover unconsolidated sands in a condition that would give useful reservoir information. DEVELOPMENT OF 'THE RUBBER-SLEEVE CORE BARREL Basic Requirements of Unconsolidated Sand Corino The basic need was defined as a core barrel that would obtain a continuous unconsolidated core with sand grains in place as deposited in the formation. A preliminary survey of coring equipment and search of the literature pointed out the weaknesses of conventional core barrels. Laboratory tests using unconsolidated sand in a metal tube simulated actual sand movement into the core barrel during conventional coring. In conventional barrels the core sometimes crumbles and bridges, or fails under compressive column action, becomes oversize, and wedges against the walls of the inner barrel. The core barrel requirements established by the surveys and preliminary tests are as follows. 1. The core should be held to- gether as it is cut so it cannot crumble and bridge against the walls of the coring tool, care being taken not to permit damage from fluid circulation. 2. The core should be continuously supported as it is cut so it will not have to support itself in compression. 3. The core should be packaged in the barrel to retain an undisturbed condition during the trip out of the well. The packaging should be such that the core can be removed from the barrel and shipped to the core analysis laboratory without physical disturbance or alteration of fluid content by exposure to the atmosphere. Operation of the Rubber-Sleeve Core Barrel The rubber-sleeve core barrel (Fig. 1) meets the basic requirements for the recovery of unconsolidated sands.

By Otto Ruhl

The zinc-lead ore reserves of the Tri-State district of Kansas, Missouri, and Oklahoma, as of December 31, 1947, are estimated at a total of 66,100,000 tons of crude ore containing 2.18 percent metallic zinc and 0.38 percent metallic lead. The Bureau of Mines began estimating the reserves in October 1945 and completed the' work December 31, 1947. A total of 38,900 acres of land representing approximately 5 percent of the area of the district is covered in this report. The work was confined for the most part to properties developed or partly developed by drilling and underground workings, and to acreage sufficiently drilled out to indicate ore of enough tonnage to make a commercial undertaking. The acreage in which ore reserves exist is widely distributed in all three States. A map of the Tri-State area is shown in figure 1. The remaining 95 percent of the area is not necessarily nonproductive but represents, possibilities for future exploration and development of additional mineral resources when and if economic conditions or national necessity encourage such work. Of the total reserves, 41 percent are in Missouri, 38 percent in Kansas, and 21 percent in Oklahoma.

Jan 1, 1949

By G. A. Grandy, P. F. Thomas, C. D. Danecki

When considering the mill drive system for a grinding application, a large number of questions must be answered. Depending on the mill size and type, the mill can be driven by several configurations of drive systems: a single low-speed motor connected to a pinion driving a ring gear, two low-speed motors connected to two pinions and driving a ring gear, or a gearless motor mounted directly. In addition, a gear drive system can have a reducer placed between a high-speed motor(s) and pinion(s) or a power path splitting pinion stand. In some designs the reducer is integral with the pinion stand driven by a high-speed motor. The technical and commercial implications of several mill drive options are presented. Initial cost, cost of installation, cost of commissioning, and cost of operation and maintenance are presented for each drive option considered. The impact of each drive system on the design, cost and operation of the overall plant electrical system is discussed. Also, consideration is given to mill drive availability, and the potential cost resulting from delays in plant production.

Jan 1, 2001