Search Documents

By Pedro Lilienfeld

This report describes the development, design, fabrication and testing of a port-able, battery-operated, light scattering monitor (henceforth to be designated as ILSDM) for the rapid measurement of the concentration of respirable dust in mining environments. This instrument incorporates state-of-the-art design characteristics and makes use of advanced solid-state components both for light emission as well as for its detection. The use of a pulsed light source combined with synchronous signal detection minimizes drift problems and optimizes the sensitivity of the measurement. Simplicity of operation, reliability and ruggedness, light weight as well as improved performance were salient objectives of this instrument development program. Continuous clean-air flow screening of all critical optical surfaces, and optimized optical detection and electronic signal processing design resulted in about a hundred-fold decrease of noise and drift with respect to precursor instruments. Equivalent mass concentration measurements 88 low as 10 micrograms per cubic meter can be routinely performed with time constants of about 2 second.

Jan 1, 1979

By Todd M. Ruff

Blind areas around construction equipment are a major contributing factor in incidents involving a piece of equipment striking a worker. In highway construction, these types of incidents result in an average of 22 deaths a year in the United States. The Spokane Research Laboratory of the National Institute for Occupational Safety and Health, in cooperation with the Washington State Department of Transportation, is evaluating methods to decrease these incidents. One such method uses devices that assist equipment operators in monitoring blind areas around the equipment to prevent collisions with workers or other objects. Several camera and sensor systems are available for this application. These systems were evaluated on various trucks used in road construction and maintenance. Tests were conducted on sanding trucks during the winter months, which allowed researchers to investigate the effectiveness and limitations of various technologies under the most extreme conditions. Tests were also conducted on dump trucks and utility vehicles during the warmer months to study the effectiveness of the systems in highway work zones. Results showed that many difficulties arise when using camera and sensor systems in cold, snowy climates. And, while the operation of these systems is more reliable during the warmer months, challenges still exist in using them on equipment in congested work areas.

bauma 2004 will feature a couple of firsts for one of the world’s largest construction and building materials machinery exhibitions. The event is scheduled for March 29 through April 4 of next year at the New Munich Trade Fair Center in Munich, Germany. For the first time, bauma will feature an exhibition area dedicated to mining equipment and technology. Also for the first time, the Commonwealth of Independent States (CIS) will be a partner region of bauma.

Jan 1, 2003

By Michael G. Pojar, Peter G. Chamberlain

Solution mining, primarily by heap leaching, has emerged as an important method for mining gold and silver in the United States. Heap leaching offers many economic and environmental advantages over conventional production techniques, in particular for lean ores and old mine waste rock. In order to more effectively pursue research on heap, dump, and in situ solution mining of gold and silver, the Federal Bureau of Mines conducted an extensive survey of leaching practices and problems. This presentation summarizes trends and statistics. Leaching is projected to provide 20 pct of primary mine produced gold and 10 pct of primary silver by the end of 1982. Current leaching practices in the United States are reviewed; operational problems and research programs to alleviate those problems are discussed.

Jan 1, 1981

By S. Z. Pethö

Pillar extraction at shallow depths with small pillars that were not originally intended for secondary extraction can provide a huge benefit to the coal mining industry in those areas where a significant percentage of the remaining coal reserves are locked up in small pillars at shallow depths and where opencast mining methods are simply not as cost-effective and practical to implement. A system considering all of the pertinent geotechnical and mining aspects for the safe and efficient pillar extraction of small pillars at shallow depths at Xstrata Coal South Africa (XCSA) has been further developed and implemented as part of an ongoing improvement process addressing all of the relevant legal and associated risk aspects. This work follows on from the previous pillar extraction work carried out at the ATC, Boschmans, and Spitzkop Collieries. The process involved a number of in-house workshops and sessions arranged with all key personnel from Tavistock Colliery, and also included Professor Nielen van der Merwe of the University of the Witwatersrand, a world renowned authority on pillar extraction, towards reviewing and developing the Modified NEVID pillar extraction system employed previously at Boschmans Colliery. The system is currently being employed at Tavistock Colliery with success and no major accidents, with around 655 000 t of coal having been successfully extracted from the pillar extraction panels.

Jan 1, 2012

Port Gaspé is located on the back side of Gaspé bay and is protected by a natural sand barrier with a length of 2,5 km, from which it got its name, Gaspé Sandy Beach (1). Since 1904 the Gaspé region had a deep water wharf, initially very different, in fact, from the one existing just before the recent reconstruction (2). This wharf with a length of 228 m and a width of 23 m was build of timber cribs. The outside walls of these cribs had been doubled with a wooden wall, creosote impregnated to provide resistance to decay and to the attack of marine organisms (limnorias) (3). Fifteen years ago the upper part of the wood construction had to be removed, because of progressing rottenness and was replaced by an L-shaped reinforced concrete structure (4).

Jan 1, 1987

By Virendra Singh

The load settlement behaviour of single pile or pile group may be obtained using computer based methods such as the finite or boundary element techniques. An alternative method of obtaining the vertical soil stresses adjacent to the Pile is presented Based on calculated stresses consolidation settlement for Piles foundation is obtained. This approach may be computationally more attractive than the more general finite or boundary element techniques.

Jan 1, 1996

By Pramod C. Thakur

In This Chapter [Origins of coalbed methane Reservoir properties of coal seams Thresholds for coal seam degasification Methane emissions in mines Methane drainage techniques How to transport gas safely in mine pipelines and Economics of coal seam degasification Recommended publications on coal seam degasification are Gas Control in Underground Coal Mining [Creedy et al. 1997], Coalbed Methane Extraction [Davidson et al. 1995], and Methane Control for Underground Coal Mines [Diamond 1994].] ORIGINS OF COALBED METHANE AND RESERVOIR PROPERTIES OF COAL SEAMS Origins of coalbed methane. Coal seams form over millions of years by the biochemical decay and metamorphic transformation of plant materials. This coalification process produces large quantities of byproduct gases, such as methane and carbon dioxide. The amount of these byproducts increases with the rank of coal. It is the highest for anthracite, where for every ton of coal nearly 1,900 lb of water, 2,420 lb (20,000 ft3) of carbon dioxide, and 1,186 lb (27,000 ft3) of methane are produced [Hargraves 1973]. Most of these gases escape to the atmosphere during the coalification process, but a small fraction is retained in the coal. The amount of gas retained in the coal depends on a number of factors, such as the rank of coal, the depth of burial, the type of rock in the immediate roof and floor, local geologic anomalies, and the tectonic pressures and temperatures prevalent at that time. The gases are contained under pressure and mainly adsorbed on the surface of the coal matrix, but a small fraction of gases is also present in the fracture net-work of the coal. Methane is the major component of gases in coal, comprising 80%–90% or more of the total gas volume. The balance is made up of ethane, propane, butane, carbon dioxide, hydrogen, oxygen, and argon.

Jan 6, 2006

A regular general meeting of the Canadian Mining Institute will be held in Vancouver, B. C., on Nov. 26-28. The Council extends a cordial invitation to all members of the American Institute of Mining and Metallurgical Engineers to attend.

Jan 11, 1919

By Douglas Bartley, Brian Wingfield, Robert McClure

Recent studies and limited tests indicate favorable results utilizing high accuracy electronic detonator technology over conventional non-electric pyrotechnic systems. This study discusses the application of this technology using the Daveytronic programmable system in an on-going production basis. The study quantifies the performance as it relates to fragmentation, excavation, vibration and productivity in an eastern U.S. aggregate mining operation. In order to insure accurate data, tight field controls were adhered to during the drilling and blasting process as they related to blast design, bench preparation, pattern layout, drilling and blasthole loading. Following the blast the excavation and crushing procedures were studied to quantify any down stream advantages due to improvements in fragmentation. This study will help provide the industry with information as to the advantages of high accuracy electronic blasting systems over conventional pyrotechnic systems and show the results of an operation utilizing electronic detonator technology through their production season.

Jan 1, 2000

By Juan Ramírez L

El presente texto describe la aplicación del método de evaluación de volquetes en minería de cielo abierto, donde se considere las variables que influyen en la operación y la factiblidad del mísmo a posteriori. Para ello, se han desarrollado dos programas para calculadora HP-41CV, que dado su carácter voluble y poder de resolución, se adecúan a este tipo de trabajo. En este sentido, el cálculo del equipo de acarreo conlleva el cálculo del mineral a extraer, cálculo del stripping, proyección de avances, velocidades y ciclos y número de volquetes necesarios para movilizar el tonelaje proyectado.

Nov 8, 1984

The French research institute, INERIS, requested the assistance of the CSIR?s Division of Mining Technology in developing further precautionary measures against explosions in their collieries. In response to this approach, an on-board active suppression system was adapted to meet their mining requirements. This system is used on tunnelling machines in Germany where the machine is positioned in the middle of the tunnel, which is therefore not much wider than the machine itself. With this configuration, the machine is never away from the tunnel face during the cutting cycle. As a result, the possible volume in front of the machine of combustible gas requiring suppression is less than 50 m3. In South Africa this technology has been adapted to suit a two-cut mining method which entails greater distances from the face and thus much larger volumes of methane mixtures requiring suppression. The particular configuration of the Explo-Stop® system being investigated required the suppression of possible methane ignition volumes of up to 180 m3of a 9% per volume methane/air mixture. The volume is a consequence of the large cross-sectional area of French underground workings and of the two-cut mining method used in France. In order to take the second cut in the coal seam, the machine is pulled back a maximum distance of 4 m, leaving an air pocket in which gas can accumulate. The machine-mounted system is required to effectively suppress any flame ignited by such a large accumulated volume of methane. The results of the protocol tests done at Kloppersbos showed that the system was capable of suppressing all simulated methane ignitions for the prescribed conditions. This was achieved with a temperature increase of less than a 100°C at the operator?s position and without any flame being detected at this position.

Jan 1, 2001

By Robert Stefanko

The concept of disposing of liquid industrial wastes by deep-well injection is not a new one. Brines associated with crude oil long have been disposed of in this manner, with the additional benefit of aiding secondary oil recovery. More recently, with the expansion of nuclear energy, the lethal, highly radioactive wastes which are by-products of the fission process have created severe disposal problems. During the past ten years, a variety of industries have resorted to subsurface disposal, some of the details of which are given elsewhere (1,2). The list reveals wide variations in injection rate, pumping pressure, cost, and waste disposition. Included are successful installations in Western Pennsylvania.

Jan 1, 1969

By David P. Shoemaker, Clara B. Shoemaker

It has been shown for an important class of complex transition intermetallic compounds (a, P, R, 6, and p phases) characterized by "normal" coordination [CN12 (icosahedral), CN14, CN15, CN16/ that interatomic distances nay be calculated to a good approximation as the sum of characteristic atomic radii. Two radii, one for major ligands and one for minor ligmds, are specified for each atom, except in the case of CN12 where only a miaaor-ligand radius is specified. The same appears to be true of transition-metal phases of simpler struc-ture: Laves phases (CN12, CN16), and p-tungsten phases (CN12, CN14). In the case of known examples of the more complex phases, a simple rule is given which specifies these radii. However, only a fraction of the known examples of the simpler phases obey this rule closely. To include the latter phases the rule may be modified by considering the radii as linear functions of the weighted average of the Pauling CN12 radii of the two kinds of atonzs, with the radii weighted according to the over-all chemical composition of the alloy. With very few exceptions interatomic distances for both tlze complex and the simpler transition phases can b$ predicted with this modified rule to within 0.06A. ManY intermetallic compounds are known of composition A,By, in which A is a transition element to the left of the manganese column in the periodic table and B is a transition element in or to the right of it. Frequently the coordination numbers (CN) found in these compounds are CN12 (icosahedral), CN14, CN15, and CN16 (called "normal" coordinations by Frank and Kasperl). Well-known examples are the cubic and hexagonal Laves phases which have CN12 and CN16, and the 0-tungsten (CrsO) phases which have CN12 and CN14. In the more complicated (often ternary) phases, such as the a phase,2 the Beck phases p3 and R~, the 6 phase,5 and the p p atoms occur with CN12, CN14, CN15, and (except for a) CN16; in many cases several crystallographically independent atoms of one particular CN occur in the asymmetric unit. A large number of independent interatomic distances are found in these complicated phases, varying from 20 in the a phase to 94 in the 6 phase. These distances show a large spread; they vary, for example, from 2.358 to 3.278A in the 6 phase. In our analysis of these distances we found that in each of these compounds every atomic position can be characterized by either one or two radii. The CN12 positions are characterized by a single radius, The higher coordinated positions are characterized by two radii, namely: the CN14 positions by 4 in the direction of the twelve "5-coordinated" ligands3 (called 'minor" by Frank and Kasperl) and by r:, in the direction of the two "6-coordi-nated" ligands (called "major" by Frank and Kasper); the CN15 positions by r15 for the twelve minor and r:, for the three major ligands; the CN16 positions by rlE for the twelve minor and r:, for the four major ligands. We have expressed the experimentally determined interatomic distances in observational equations as the sums of the appropriate pairs of these characteristic radii and the value of these radii have been determined by the method of least Squares. Despite their wide range, the interatomic distances could then be predicted by the sums of these atomic radii with an average deviation in any one compound of 0.06A or less. The results are summarized in Table I. Inspection of the radii thus obtained shows that in the structures in Table I the radii (in A) are given to a first approximation by the simple relationship: Where CN is the coordination number (12, 14, 15, or 16), and A = 1 for major ligands and = 0 for minor ligands. The interaLomic distances can be predicted within about 0.1A by sums of these atomic radii. Another phase belonging in this group with CN12, 14, 15, and 16 is the y phase & B7, in which A is molybdenum or tungsten and B is iron or cobalt. Recently the M%C phase has been refinedE and the observed distances also agree well with those calculated with Eq. [I]. (In the original determination of the structure of W6FeV7 the F$(II)-W(II1) distance was erroneously given as 2.84A, but we have recalculated it fro? the published parameters and found it to b? 2.57i4, in good agreement with the value of 2.6A predicted with Eq. [I.].) Many binary transition alloys are known to crystallize with the simpler structures having "nor-

Jan 1, 1964

This chapter presents an overview of fatal and nonfatal injuries reported to MSHA during 1986-1995. Reportable injuries follow the criteria for reporting specified in 30 CFR 50. These criteria are listed in appendix A. The data used for these analyses came from the MSHA accident, injury, and illness data closeout files for the years 1986-1995. The MSHA data are described in appendix A and methods used in data analysis in appendix B. There may be slight discrepancies between the figures presented here and other presentations of MSHA data for the following reasons: (1) injuries to nonemployees have been excluded from analysis; and (2) injuries identified by MSHA after the files were closed out are not included. Within the MSHA data, there are differences in reporting requirements for operators and contractors. Contractors are required to report only those injuries that occur during certain categories of work (described in appendix A). For this reason, data on injuries among employees of operators and contractors in the MSHA database should not be considered directly comparable. As discussed in the "Introduction," the MSHA data on fatal injuries differ from the CFOI data (chapter 1) because of varying definitions used for the mining industry. As compared to the CFOI data, MSHA data exclude injuries that occurred off of mine property and include injuries occurring at mills and processing plants on mine property. Tables 4-1 through 4-9 and figure 4-1 provide comparisons of injury frequencies and rates among the commodities. These comparisons are followed by sections 4A through 4E, which provide more detailed tables and figures for each commodity separately. The method used to calculate injury rates is described in appendix B. Since denominator data for occupations (lob titles) were available for 1986 only, estimates of rates by occupation for the entire 10 year period are based on extrapolation from 1986 data. For this reason, estimates of injury by occupation should be interpreted with caution. Fatal Injuries A total of 1,078 fatal on-the-job injuries were reported to MSHA during the 10-year period 1986- 1995. The average annual fatal injury rate for all commodities combined during this period was 30.9 per 100,000 full-time equivalent workers. Mine operators accounted for 908 (84%) of the fatalities and had an average annual fatal injury rate of 28.2 per 100,000. While mine contractors comprised only 16% (n = 170) of the total number of fatalities, their average annual fatal injury rate was 2.3 times higher than that of mine operators (65.0 per 100,000). Table 4-1 presents the number and rates of fatal injuries by commodity for operators and contractors. Contractors in metal, nonmetal, stone, and sand and gravel are grouped together, since MSHA data on employment were not available for rate calculations for these commodities separately. The highest average annual fatality rate for the period, 66.5 per 100,000, occurred among metal and nonmetallic mineral mining contractors, followed closely by coal contractors (63.1 per 100,000). Among mine operators, the highest average annual fatal injury rate was in coal (38.9 per 100,000); the lowest was in nonmetal (14.3 per 100,000). Table 4-2 shows the average annual fatal injury rate by type of operation for each commodity for mine operators only. Of commodities with underground mines, all except stone had higher fatality rates at underground than at surface operations of these mines. The highest fatality rate for any operation occurred in surface operations at underground stone mines (124.5 fatal injuries per 100,000 workers). Stone had the second highest fatality rate for underground operations at underground mines (77.9 per 100,000). The highest rate for underground operations at underground mines occurred in metal (87.6 per 100,000). Table 4-3 shows the number and rate of fatal injuries by U.S. Bureau of the Census occupational groups (described in appendix D) for the 10 occupation-commodity groups with the highest fatal injury rates. These data should be interpreted with caution because the denominator used in calculating the rates was based on an extrapolation from data for the year 1986 only, as described in appendix B. Extractive occupations are represented in this group for three commodities: coal, metal, and sand and gravel. Construction trades are included for coal, sand and gravel, and nonmetal. The distribution of fatal injuries by commodity and work activity for mine operators is presented in table 4-4. A description of the work activity categories is in appendix C. Overall, the leading work activity at the time of injury was using or operating tools and machinery (26.4%) followed by constructing, repairing, and cleaning (24.0%), vehicular operations (18.8%), and materials handling (12.6%). The distribution varied by commodity. The largest percentage of fatal injuries occurred while operating tools and machinery in both coal and stone; during vehicular operations in metal; and during constructing, repairing, and cleaning activities in nonmetal and sand and gravel. Table 4-5 shows the distribution of fatal injuries by commodity and MSHA accident classification for mine operators. A description of the MSHA accident classifications appears in appendix E. The largest proportion of injuries overall occurred during powered haulage (28.5%). The

Jan 5, 2000

By Ronald Mamani, Russel Allidren, Diego Llanchipa

Esta investigación tuvo como objetivo evaluar la eficiencia del Sistema Tohá —conocido como Lombrifiltro o Biofiltro Dinámico y Aeróbico— para el mejoramiento de la calidad de aguas residuales domésticas. Para evaluar los parámetros DBO5 y DQO se tomaron como puntos de referencia aspectos biológicos del agua a tratar, que pasó a través de un biofiltro compuesto de 4 estratos (aserrín, grava, arena y carbón), el primero de los cuales incluyó lombrices rojas (Eissenia Foetida). Antes y después de realizar el filtrado se realizaron análisis de laboratorio. Como resultado respecto de remoción de contaminantes, se obtuvieron cifras que implicaban reducciones superiores al 50%.

Aug 31, 2019

By K. D. Russ, A. J. Beer

Non-contact systems for measuring underground voids have used theodolites, reflective or non-reflective laser methods and sonar techniques. An effective but cheaper alternative is based on use of a Wild T1000 electronic theodolite coupled to a Leica Data DISTO and a Wild GRE3 data logger. The software used to process the theodolite data is a spreadsheet and macro combination, while Surpac, Datamine and AutoCAD modelling packages have been investigated for viewing the tunnel profiles. The main limitations were found to be blinding, when irregularities in the stope obstructed the line of sight, and the 30 m range of the Data DISTO model used in the study, although more powerful models are available. All three modelling packages proved suitable, with Surpac providing the best-quality printed images of the voids surveyed and AutoCad by far the cheapest alternative

Jun 21, 1905

By Robert Blickensderfer

Tungsten alloys with high-temperature strength properties, comparable to the best of alloys recently developed by others, were produced by a new process called here the oxyreaction process. The process involved additions of a powder of a reactive metal compound, ZrN, ZrW2, or HfW2, to a base metal powder, tungsten, which contained some oxygen. The powders were blended, compacted, sintered, and extruded. During sintering, diffusion and internal oxidation occurred to produce reactive-metal oxide particles and solid solutions. A dispersion of oxide particles could be precipitated by heat treating. The oxyreaction process circumvents many of the agglomerating and coarsening problems encountered in the current methods for dispersing a stable oxide in a metal. Oxyreaction strengthening results from solid-solution strengthening and from dispersion strengthening produced by the reactive metal and its oxides. At a test temperature of 1,650° C, the alloys prepared from WW, had tensile strengths up to 70,000 psi and stress-rupture lives up to 142 hr at 10,000 psi stress; the alloys prepared from ZrN powders had tensile strengths up to 80,000 psi and stress-rupture lives up to 27 hr at 10,000 psi stress. Tensile strengthening in the alloys was attributed to Zr in solid solution or to Zr-O-W structures too small to be observed in an electron microscope replica. Stress-rupture life was attributed to a dispersion of submicron Zr02 particles which precipitated and grew to 0.05-to 0.2-micron size during the test. Tensile strengthening and stress-rupture life were dependent upon both the zirconium and oxygen contents with the maximum occurring at roughly 0.9 atomic pot Zr and 0.9 atomic pot 0. Studies of the details of the oxyreaction process were made on the W-ZrW2 alloys and three general steps were determined: (1) The reaction of 0 in tungsten powder with ZrW2 to form relatively large Zr02 particles; (2) the dissolution of remaining ZrW2 into the W matrix and partial internal oxidation to form ultrafine but sparse zirconium oxide particles and possibly to establish Zr-O-W structures; (3) the development of ultrafine Zr02 particles during high-temperature aging.

Jan 1, 1971

By D. Morris D

La utilización de recursos minerales como el plomo, zinc y sus metales asociados como subproductos genera beneficios para el personal laboral, inversionista y público, en tanto el estado general de la economía se encuentra relacionado con los bienes que puedan ser vendidos en los mercados mundiales. Empero este progreso y desarrollo técnico en la extracción metalúrgica, no debe limitarse a la cantidad de energía utilizada durante la operación, ni al beneficio acumludado durante este tiempo, sino se debe evaluar las condiciones de estos rendimientos y transformarlos en una ayuda para todos los involucrados, a partir de los descubrimientos científicos posteriores.

Jun 20, 1954

By Edison Roberto Celis

El presente trabajo señala la posibilidad de ocurrencia de accidentes graves y fatales en relación con los riesgos que se evalúan durante la aplicación de la estrategia de control. La estrategia incluye una selección de actividades, lugares, personas y equipos que deben ser incluidos en el proceso, y se basa en una evaluación previa de la data de seguridad existente en la operación, para estimar las direcciones probables de aplicación de la herramienta. Finalmente se elabora un mapa coloreado de probabilidades que permiten al gerente analizar y decidir el inicio del control de la probabilidad de accidentes graves.

Sep 12, 2011