Search Documents

By H. H. Schrenk, W. P. Yant, F. A. Patty

"INTRODUCTION In accordance with the outline of investigation described in a previous report 5 of the Bureau of Mines dealing with the use of acrolein for detecting leakage of methyl chloride from unit--type refrigerating systems, the work has been extended to include an investigation of its use in a multiple system, This report gives the results of analysis of samples of the gas from representative units of a multiple system charged with methyl chloride containing approximately 0.9 per cent acrolein by volume, The results furnish a basis for estimating the Warning that would be given in event of leakage. The properties and warning intensity of acrolein have been described in a previous report. 5 ACKNOWLEDGMENTSThis investigation was made at the combined request-of Several Inc., Manufacturers of refrigerating, appliances, and the Roeasler Hasslacher Chemical Co., manufacturers of methyl chloride. Acknowledgment is given to R. M. Major, ,chief chemist of the former firm for arranging the experimental site and equipment; to Arthur O. Haseeneall, owner of the apartment building where the investigation was conducted, for his courtesy in permitting the investigation; and to R. R. Sayers, chief surgeon, Bureau of Mines, and surgeon., U. S. Public Health Service, for suggestions and advice."

Sep 1, 1930

A comparison is made between elementary block estimation techniques and the optimal methods of geostatistics using data from an Australian deposit. Considerable improvement in the estimates are obtained by using the optimal technique in this case.

Jan 1, 1975

By Jesse J. Brown

Over 60 simple; were prepared and forwarded to Dr, S. Z. Toma, TPO, PMSRC as a result of this project. Included among these samples were various low temperature forms of silica. Samples of quartz, cristobalite, and tridymite with iron, manganese, and titanium impurities present were prepared. In addition, a long series of samples both wet ground and dry ground for times from 1/2 to 8 hours were prepared. Numerous miscellaneous samples were submitted which included kaolinite, calcite, muscovite, illite, montmorillonite, Ba3(P04)2, and YPO4 among others, in response to special requests from the TPO. The silica rich portion of selected binary (CA 203-Si02, In 203-Si02, Li20-Si02) Na20-Si02, PbO-Si02, SnO2-Si02, Sn02-Si02 BaGa204-SiO2 and SrGa204-Si02) and ternary systems (Na20-Ga203-Si02 and Li20-Ga203-Si02) was investigated to determine the effects of solid solubility on the stabilization of the high temperature forms of tridymite. In addition to the determination of the extent of these crystalline solubilities, observations were made. on the mechanism of the transformation of silicic acid to tridymite and the rate of the reaction in the presence of foreign ions,

Jan 1, 1973

The safety of mining operations is significantly influenced by the in situ stress fields in which the mining excavations are created. From the point of view of planning of mining operations, the in situ stress field is a most important input parameter for valid modelling of excavations. Many in situ stress measurements have been carried out for mining and civil engineering projects in southern Africa over the past 30 to 40 years. A database of in situ stress measurement results and observations has been compiled. This paper presents results extracted from the database which are considered to be of particular interest to mining areas in South Africa. The database will permit the estimation of likely stress conditions in new areas of mining, provide a basis for evaluation of results from future in situ stress measurement programmes, provide a basis for comparison of observed behaviour with expected behaviour, and provide a source of data on which realistic design and layout analyses can be based. The information contained in the database indicates that horizontal to vertical stress ratios in the Carletonville, Klerksdorp and Rustenburg areas are significantly higher than the value of 0,5which is commonly used in mine layout planning.

Jan 1, 1998

By T. O. Llewellyn

The Bureau of Mines conducted batch-?scale tests on a sample of parphyry copper mill tailings as part of a study to determine the feasibility of rutile recovery from this source. The tailings that were tested contained 0.75 percent titanium dioxide (Ti02), with about two-thirds of the Ti02 values occurring as rutile. Mineralogical studies indicated that about one-half of the Ti02 content could be considered recoverable. Beneficiation studies of the tailings showed that best flotation results were obtained when sulfides and carbonates were removed by bulk flotation prior to rutile flotation. Rutile flotation was most effective when a petroleum sulfonate collector was used in an acid circuit. From this basic method of flotation, two alternative procedures were developed. The first procedure was to size and grind the tailings to minus 200 mesh; deslime the total pulp; and then float the sulfides, carbonates, and rutile. The second procedure was the same, except that it did not include sizing and grinding. Flotation of the sized and ground tailings yielded rutile concentrates containing 43.1 percent Ti02 and 75.7 percent of the recoverable Ti02. Rutile concentrates floated from the tailings that were deslimed but not ground contained only 34.7 percent Ti02 and 69.4 percent of the recoverable Ti02.

Jan 1, 1980

By Lawrence M. Gochioco

The interpretation of coal seismic data requires a certain precision and accuracy to make the results more reliable. The signature of the seismic wavelet provides a host of valuable geologic information. Subtle features and anomalies, not easily observed in conventional black and white seismic sections, are enhanced through color attribute displays in terms of frequency, amplitude and phase. Coal seam anomalies like sandstone washouts produce a distinct pattern in frequency and amplitude displays due to the change in the net acoustic impedance contrast. Faults produce frequency and amplitude variations due to interference within the Fresnel zone that straddles the fault. The magnitude of displacement is estimated by studying the effects of faults on reflection amplitudes and frequency from computer-generated models.

Jan 1, 1989

By Omar Manfredo Herrera Terrazas

La mina Toquepala, propiedad de Southern Perú, es un yacimiento de cobre que desarrolla fases de minado de expansión y profundidad, en cuyas paredes finales se reflejan la competencia de los taludes, con el objetivo de soportar la carga portante de la masa rocosa. Sin embargo, los problemas de inestabilidad, tienen su origen en diversos aspectos, como geológicos, redistribución de esfuerzos, y diseño. Asimismo, las voladuras no controladas, alteran en forma progresiva y sistemática los parámetros geomecánicos del macizo rocoso. Por ello, el presente trabajo describe la perforación y voladura controladas de pre-corte como un método que brinda los beneficios de seguridad, control de vibraciones, incrementos de las reservas minerales por fase y disminución de la relación desbroce - mineral.

Sep 14, 2009

By Lucien Weber

In the Shanghai area, the soil conditions are such that bearing piles have become an essential foundation part of the new highrise buildings. In order to reduce the settlements under the high working loads of about 2300 kN/pile, the Chinese building authorities require the pile tip to penetrate into the compact sand layer, situated at approx. 60-70 m depth. No H-piles have yet been tested under these conditions in Shanghai. This paper describes the driving of 8 H-bearing piles with 4 different shapes and with lengths varying from 45 to 75 m. Dynamic measurements are performed during driving and after a wait time of approx. 40 hours in order to assess the change in bearing capacity in function of time and in order to get an idea about the resistance distribution along the piles by using a stress wave analysis program (CAPWAP). One pile is equipped with channels between the flanges for executing verticality measurements with an inclinometer. However, this test has not yet been performed. One month after driving, two piles of 75 m length are statically loaded both in vertical and in horizontal directions.

Jan 1, 1987

By H. H. Wade, N. F. Schulz

The large quantities of iron-bearing materials, including taconite, semi-taconite,* and other low-grade ferruginous materials occurring in Minnesota and elsewhere, constitute an important potential source of iron. Satisfactory grade and recovery of iron ore concentrate cannot ordinarily be obtained from these ferruginous materials by simple methods of beneficiation. Iron is distinctive in that the free metal and two of its oxides [magnetite (Fe2O3) and maghemite (gamma-Fe2O3) ] are strongly ferromagnetic. The successful magnetic separation of natural magnetite from taconite has already been established on a commercial scale. The iron in semi-taconite, however, occurs largely as goethite (Fe2O3-H4O) and hematite (Fe2O3) which do not respond to ordinary magnetic separation methods. Magnetic roasting converts these iron oxides to magnetite, which can, after liberation, be magnetically concentrated. MAGNETIC ROASTING Hematite undergoes a stepwise reduction when exposed at moderately elevated temperatures to a reducing atmosphere containing hydrogen or carbon monoxide: Fe2O3? Fe3O4 ? FeO ? Fe Since the desirable product in magnetic roasting is Fe3O4, the conversion is halted after the first stage by controlling the reduction potential of the gas mixture with water vapor or carbon dioxide. The reducing gas mixture must be such that the oxygen partial pressure at the solid-gas reaction interface will be maintained intermediately between the oxygen partial pressures in equilibrium with Fe2O3 and Fe3O4 at the prevailing temperature. Because of the rapid increase in decomposition pressure of Fe3O4 with increase in temperature, the practical upper limit of useful reaction temperature is about 1400°F, above which over-reduction usually occurs in atmospheres containing hydrogen or carbon monoxide. On the other hand, useful reaction rates usually occur only above 800°F. Goethite reacts similarly except that the combined water probably has to be driven off thermally before the reduction to magnetite occurs. Iron carbonate must also be decomposed thermally to an oxide before conversion to magnetite. Iron silicates are apparently not amenable to magnetic roasting. The rate of penetration of the reaction toward the interior of a given ore fragment is dependent on the chemical composition and physical structure of the solid. Most ore fragments tested here reduced satisfactorily to 1/4-in. depth in less than 14 min at 1200°F. Some very dense fragments, however, were reduced to less than 1/32-in. depth under the same conditions. Determination of the optimum temperature, gas composition, ore fragment size, or time of exposure

Jan 1, 1961

The importance of timbering, not only from a financial point of view but from an actual mining point of view, is so often overlooked or slightly glossed over by the average expert and investor, that I have thought it would prove interesting to go into the matter and to invite discussion upon the subject. We will first take small veins, or reefs as they are termed in some mining countries; and by small veins it is intended to denote fissures from a few inches to three feet. The ore body is supposed to be confined within well defined walls free from gangue matter, unless the casing can be defined as such. Now, if the walls are smooth and moderately hard, no timbering is required other than the stulls, which are braced from wall to wall in order to form platforms or stages to stope from. Should the reef from wall to wall prove payable, or should the vein be of a character to prohibit cleaning or sorting; and it be determined to send the whole of the stone to the, reduction works, the stuUs should be left in place until the section or block of ground is worked out, in order that if a weak spot in the walls (especially the hanging) occur, it would be possible, without any particularly extra expense or difficulty often times accompanied by danger to brace and secure the slabs. After the block became entirely stoped, it would pay where labour was cheap to remove the majority of timbers to stull another section.

Jan 1, 1901

By Y. L. Sun

The feasibility of using the ultrasonic wave attenuation method for measuring in-situ stress is examined theoretically and experimentally. The theoretical analyses show that for a given rock type the relation between stress and attenuation coefficient ratio can be approximated closely by second-order polynomials. Combining the elastic and statistical theories, the magnitude and direction of the existing principal stresses can be predicted by using the relations between stress and attenuation coefficient ratio obtained in the calibration of core specimens. Several experiments are conducted in the laboratory on two types of rock. The experimental study consists of two parts: the attenuation-coefficient measurements in core specimens under uniaxial stress and the attenuation coefficient measurements in boreholes drilled through blocks of sandstone and limestone subjected to uniaxial compressional stress. Compressional waves are used exclusively in the measurements.

Jan 1, 1989

By J. M. Somers

Methane is a powerful greenhouse gas and the principal component of natural gas. Coal seams often contain significant quantities of methane, and underground coal mines must ensure that methane released into the mine during coal extraction does not build to dangerous levels. This is accomplished in part through the use of large-volume ventilation systems that remove methane from the mine and release it to the atmosphere. Although the methane concentration exhausted is quite low (typically <1 percent), the volume of air that ventilation systems move is so great that they actually constitute the largest source of methane emissions from underground coal mines. Each year underground coal mines throughout the world emit more than 500 billion cubic feet of methane from their ventilation systems. An air pollution control technology, thermal oxidation using a flow-reversal reactor (TFRR), has emerged as a potential solution to ventilation air methane (VAM) emission mitigation. One manufacturer of TFRRs has demonstrated its oxidizer design (the VOCSIDIZER?) at coal mines in the United Kingdom and Australia. These demonstrations tested the technology?s effectiveness at oxidizing low-concentration methane, as well as its ability to tap the excess heat to produce steam for electric power generation. In early 2007, the first U.S. demonstration of this technology began operation at an abandoned mine in West Virginia. The project is designed to prove the technology?s operational robustness, its ability to reliably oxidize methane at concentrations typical of mine exhausts, and its safety. If the technology is employed at active underground coal mines, it offers the potential to mitigate substantial quantities of global methane emissions. This paper discusses global VAM emissions, options for the recovery and utilization of VAM, and existing projects such as WestVAMP in Australia and the ongoing U.S. VAM demonstration project.

Jan 1, 2009

By Elisa Comis, Jeffrey Peterson, Yama Ebrahimi

Construction of the Northeast Boundary Tunnel (NEBT), the last leg of the Anacostia River Tunnel System on DC Water’s Clean Rivers Project, started in September 2018 and was completed in April 2021. The 26-foot-bore earth pressure balance (EPB) tunnel boring machine (TBM) mined 26,737 feet at elevations between 80 to 160 feet belowground. Approximately 55% of the tunnel was cut through lower predominantly coarse-grained facies identified as the Cretaceous Patuxent Formation (undifferentiated) (PTX), and the remainder was cut through upper predominantly overconsolidated fine-grained plastic material facies identified as the Cretaceous Patapsco/Arundel Formation (P/A). Mixed face conditions were encountered in the transition from the P/A to the PTX and vice versa. This paper reviews the performance of the TBM that mined the NEBT through several unique challenges, including 8,000 feet of tunneling under the heavily developed Rhode Island Avenue corridor, major sensitive structures, cast iron water distribution mains, and other sensitive utilities.

Dec 1, 2022

By W. L. Cornell

The Missouri lead ores are the only domestic sources of cobalt presently being mined and processed for other materials. They represent the best short-term solution for meeting up to 13 pct of the Nation&apos;s strategic and critical cobalt needs from domestic sources. Presently, the cobalt is lost as an impurity in the copper, lead, and zinc concentrates and in the mill tailings because the technology to recover it with minium impact on present production does not exist. This paper presents results of research, built upon earlier Bureau of Mines laboratory research, to enumerate the problems encountered in cobalt recovery from the copper concentrate under actual mill conditions; to present alternative solutions to these problems; and finally, to describe the best available technology for cobalt recovery within the imposed constraints. Mineralogical analyses showed the cobalt present as a distinct mineral phase, predominately siegenite, amenable to a physical separation method such as froth flotation. Flotation was chosen for recovery because of easy adaptation by the mills. Unit processes of grinding, conditioning, and flotation were studied individually and in concert, and a series of continuous tests were run based on the parameters developed to obtain engineering data for subsequent economic analysis. Overall cobalt grades of 3.00 wt pct at a recovery of 64.0 pct were achieved.

Jan 1, 1987

Continuously monitor and record respirable dust levels underground by a reliable, sensitive, and fast-response device. Approach A light-scattering photometer, having a LED (Light Emitting Diode) light source and other significant improvements, has been designed and incorporated into a portable continuous monitor. How It Works The monitor continuously draws air into the sampling inlet through a cyclone that removes dust particles larger than respirable size. The dusty air enters the photometer vertically downward through a cylinder which is intersected by the optical system. (This cylinder appears as a circle in the drawing of the photometer.) The center of he column of dusty air intersects a beam of pulsing light from the LED, causing some of the light to be reflected, scattered, and refracted. Only the light that is scattered at an angle of about 700 from the light beam passes through a lens to the photodetector which generates an output voltage Signal proportional to the dust content in the air. This signal is detected, amplified, and converted to a digital readout directly in milligrams of dust per

Jan 1, 1979

By E. D. Palmes

Phase I of these studies demonstrated the feasibility of measuring the efficiency and capacity of sorbents in tube-type samplers for contaminant gases. This was accomplished by measuring concentration at various points along the length of the diffusion path during sampling. Concentrations were measured by removing small aliquots with gas-tight syringes and gas chromatography. With hexane as the gas and activated charcoal as the sorbent the procedure was quite successful and we proceeded with Phase II of the study; this involved application of the principle to gases of importance in diesel exhaust using a variety of sorbents. When we worked with high concentrations of the test gas we clearly demonstrated the differences in both efficiency and capacity of the sorbents for each of several gases. The chief drawbacks of the system were that we were unsuccessful in determining more toxic gases at realistic occupational exposure levels or determining formaldehyde at any level using the flame ionization detector. It was concluded that, although the method is feasible, more sensitive methods of measuring concentrations of gas in the tube must be developed to make the procedure applicable to regions of chief industrial hygiene interest.

Jan 1, 1983

By Leoncio Méndez, Jesús Arguijo, Juan José Frausto, Daniel Castruita, Daniel Aguilar

Minera Sabinas (Grupo Peñoles), localizada en Sombrerete, Zacatecas, México, produce concentrados de cobre y zinc. Su proceso es un circuito de conminución de quebradoras y dos molinos de bolas en circuito cerrado con hidrociclones seguido de un circuito de flotación, a partir de mineral polimetálico extraído de una mina subterránea. Su problemática consiste en que la recuperación por flotación disminuye significativamente cuando minerales con contenido de pirrotita son procesados. La flotabilidad natural de la pirrotita supera la cinética de flotación de las especies de cobre y zinc y limita la capacidad de la concentradora para generar concentrados vendibles. Este artículo presenta un diagnosticó de los problemas que se tienen cuando se procesan minerales con alto contenido de pirrotita, así como resultados de un programa experimental a escala laboratorio realizado en el CIDT de Peñoles y en sitio. La investigación se enfocó en definir un esquema de reactivos para poder procesar minerales con pirrotita en su composición. Compósitos de alta y baja ley de cobre fueron usados en la investigación. Se identificó el agua de proceso como una fuente de iones calcio y sulfato. Se desarrolló un esquema de reactivos orientado a promover la selectividad de las especies de valor respecto a la pirrotita, incluyendo tratamiento del agua de proceso.

Sep 20, 2019

By Paul G. Swanson

This investigation was conducted to identify the principle causes of spoil instability problems in the Eastern Coal Province. The study was also conducted to develop a matrix to predict the strength and groundwater parameters necessary to conduct stability analyses on a proposed reclamation scheme. Suggestive methods to reduce spoil instability potential are also included. Numerous physical property, strength, compressibility, chemical and mineralogical tests were conducted on mine spoil samples obtained from 11 different surface mine sites. Site characteristics that influence the position of the post reclamation groundwater table were identified. Distinct regions within the Eastern Coal Province with high incidences of surface mine slides or high landslide susceptibility were identified. The application of the predictive matrices developed in this study is for surface mine sites mined and reclaimed in general accordance with the Surface Mine Reclamation Control Act of 1977. A review of current mining practices and the relative effect on spoil stability is included.

Jan 1, 1983

Gas-liquid contacting in the packed bed is a common operation in metallurgical reactors. Research has shown that, unlike wetting flow, non-wetting liquid flows in the form of discrete droplets or rivulets. Thus, modeling of the liquid phase as a continuum is in contradiction to the observations. Also, for the non-wetting case, continuum models have failed to describe liquid flow path when the liquid source is a point source. The aim of the current work is to put forward a combined Lagrangian-Eulerian approach to model the liquid and gas flow in the packed bed. Liquid is assumed discrete and modeled using a force balance approach. Gas is assumed to be interpenetrating continua and modeled using k-emodel for turbulent flow. Structured packing is assumed and x- ray imaging technique is used to visualize liquid flow lines in the bed. Simulation results for liquid flow path compared with the experiments.

Jan 1, 2006

Dada la remoción del material mineral o estéril a quebrantarse, es de vital importancia la elección y el uso adecuado de los explosivos en la explotación minera de Atacocha. Por tal motivo, el objetivo del texto señala la eficacia de la voladura de explosivos según el tipo de mineral a romperse y la geología del yacimiento. La selección de detonantes es de acuerdo a su peso sobre la base de su potencia relativa comparada con la nitroglicerina. Entre la selección de explosivos en trabajos mineros subterráneos se considera las siguientes características: potencia, velocidad, sensiblidad, resistencia al agua, densidad y gases producidos por la explosión. Así como el método de carga, diámetro de taladro, clases detacos usados, el modo de atacar, diámetro del cartucho y la demanda de explosivo en el mercado. El método de carga requiere que el explosivo sea flexible para llenar los espacios vacíos del taladro y prevee que el uso de cartuchos plásticos faciliten las cargas en taladros verticales usados en nuestros stoppes de corte y relleno. Cabe recordar que la resistencia de los cartuchos a la humedad no siempre se aplican al agua puesto que en las minas de Atacocha, su impermeabilización es de lo más común. De otro lado, las mechas se componen de tres o más capas impermeables y las cápsulas se fijan a las mechas de seguridad por medio de alicates especiales. Finalmente, los explosivos utilizados el yacimiento de Atacocha, se seleccionaron de acuerdo a las características físicas de las masas de roca y mineral que influyen en el problema de su arranque (tenacidad, fragilidad, dureza, plasticidad de la roca misma, planos de estratificación, exfoliación, grietas y quebraduras), sin encontrar dificultad en su voladura dada la suavidad del mineral como de las rocas.

Jul 20, 1957