Search Documents

By Matthew Janes

Statnamic load testing is becoming widely accepted as a method to quickly and economically determine the load-deflection behaviour and ultimate static resistance of high capacity deep foundations. Strain instrumented large diameter bored shafts were tested at four locations for the federal and state Departments of Transportation in the United States. Tests were conducted vertically (to 30 MN) and laterally on the shafts and, in some cases, testing was completed over water. Instrumented shaft test results provided shaft load distribution with depth and shaft shear transfer stress throughout the soil stratum. Shaft end bearing and ultimate end bearing stress values were provided. On two projects, Osterberg load cells provided comparative static data for skin friction and end bearing. Correlations between Statnamic derived static load-displacement results and Osterberg load-deflection results are very good. Statnamic lateral load test results were correlated with static lateral results in addition to providing useful dynamic response and damping data.

Jan 1, 1996

By A. B. Hooker, E. J. Coggeshall

"Dry cells are modified wet primary cells in which the electrolyte is held by absorbent material so that it does not spill aid the cell jars are sealed to prevent evaporation of the absorbed electrolyte. Most dry cells in commercial use are modifications of the Leclanche wet cell. In their usual form they have a hollow cylindrical zinc negative pole that constitutes the containing vessel. An absorbent material, either as a lining in the zinc jar or a bag, separates the zinc cylinder and a rod or flat plate of carbon placed axially inside. A mixture of crushed coke, graphite, and manganese dioxide is tamped about the carbon rod, and the whole mass is saturated with salaanoniac-zinc chloride solution.Dry cells are suitable for services that require minute currents continuously or larger, though limited, amounts of current intermittently. Though limited in this way, they have a wide use, even in underground mining. This paper details some of the applications of dry cells in mines, particularly from the standpoint of greater safety through their use.APPLICATIONSThere are four fields of application of dry cells to mining: (1) Electric shot firing; (2) auxiliary lighting; (3) signaling; and (4) testing.SHOT FIRINGFiring an electric detonator requires very little electrical energy because although the current flow may be 1 to 3 amperes the duration of flow is so small (1 to 4 milliseconds) that the energy withdrawal per shot is almost negligible. Batteries for shot firing need not be large; they may be used for firing either single or multiple shots."

May 1, 1934

By T Leach, B Fulton, R Stewart

Gold mineralisation at Porgera is inferred to have been derived from a deep differentiated magmatic source which is capped by a series of (now tilted) inward dipping sills and stocks, which comprise the Porgera Intrusive Complex. An arc normal transfer structure provides a conduit, at tile intersection with an arc parallel structure, into which basic magma derived from tile deep melting of mantle material has been emplaced. Two phases of mineralisation display an association with late stage feldspar porphyry intrusives. Stage I carbonate-base metal-style gold mineralisation occurs as early quartz-sericite, then massive sulphide and late zoned Mn-Fe-Mg-Ca carbonate vein/breccias. Magmatic fluids derived from the deep magma source, are interpreted to have migrated along me margin of a feeder stock to the sills, and south to Waruwari. Stage II epithermal Au-Ag quartz-style gold mineralisation occurs as early fluidised breccias and carbonate veining, followed by zoned quartz-roscoelite-carbonate-gold vein/breccias, and late carbonate and/or sulphate open space infill. Magmatic fluids are interpreted to have utilised the same plumbing system as the late stage feldspar porphyry intrusive, and then migrated into the Roamane Fault which was dilated by; dextral rotation on elements of the transfer structure, normal faulting, and refraction around the competent footwall hornblende diorite. Bonanza gold is localised in a jog in the Roamane Fault, hangingwall splits and at intersections with cross structures. Bulk low grade Stage I gold has been deposited by the mixing of magmatic fluids with cool gas condensate waters, whereas high grade Stage II gold mineralisation resulted from the rapid quenching of mineralised magmatic fluids by oxygenated groundwaters.

Jan 1, 1995

By Eugene R. Rice

There are many methods for determining the meridian, but all of those in common use involve at least two separate observations, one for latitude and one for azimuth. Such observations made upon a south star at any hour are open to the objection of possible inaccuracy due to ignorance of the absolute refraction, and also to slow change in the altitude of the star when near the meridian. The method of observing a circum-polar star at elongation. besides requiring a separate observation for latitude, is open to the serious objection that clouds may obscure the star at the critical moment. Moreover, a tedious wait for the star to come to elongation is sometimes necessary. Many of us can recall 'long, cold, weary vigils, waiting for Polaris to reach elongation. For observing a circumpolar star at any hour, not only the latitude, but also the true time, must be known. This it is practically impossible to obtain, except in regions reached by the telegraph, and usually then one has to know the longitude also, in order to reduce " standard time" to " local time." The results obtained by this method, when the star is at culmination, are not very good, unless the true local time is absolutely known. The methods of obtaining the nleridian from the sun, by means of a solar attachment, or by direct observation, while good, are not absolute, by reason of refraction, change in declination of the sun, and small change in vertical angle, when the sun is near the meridian. For these two methods, latitude, time, and approximate longitude have to be known. In the method here described, only one observation is needed, and from it are computed azimuth, latitude, aud sidereal time. In other words, one call observe a circumpolar star—Polaris

Jan 1, 1911

By Michael Alber

Resin grouted rock bolts are the major support measure in coal mining. They are rather easy and foolproof to install, take immediately load and are the least time consuming support measure for controlling gateroad deformation. The use of only resin grouted bolts allows fast gateroad development which is essential for economical resource exploitation. The design of reinforcement / support systems for coal mining typically bases on empirical methods, which work fine when encountering known or usual ground conditions. However, coal mining approaches depths where little experience exists and numerical modeling is often the only method to estimate ground behavior. This paper discusses the geotechnical properties relevant to numerical model and focuses particularly on input values for modeling resin grouted rock bolts for safe gate design.

Jan 1, 2006

By E. D. Gardner

During the summer of 1935 a plan was proposed by which the Government should establish custom sampling plants for gold and silver ores in the mining districts of the West, where the construction of such plants would be justified as an unemployment relief measure. It was known that in many districts prospectors and small operators had small lots of smelting ore that could not be marketed for lack of sufficient capital to get out enough ore at a time to make carload shipments to distant smelters. Moreover, considerable ore of milling grade was available in many districts in which there were no custom milling facilities. It was felt that. accurate sampling and the classification and consolidation of small lots of ore produced from prospects and small mines, with quick cash returns to the shippers on a nonprofit basis, would stimulate the working of small gold and silver properties: Idle mines would be put to work, and there was a possibility that some of the prospects could be developed into regularly producing mines. Each sampling plant was to be centrally located so as to serve the greatest possible number of mines and prospects. Wherever possible, the plants were to be built on a railroad, is ore of smelting grade accumulated, it was to be shipped to a smelter in carload lots. Where a plant was not on a railroad, smelting ore was to be trucked to the railroad after being sampled.

Jan 1, 1936

By K. E. Waters, J. E. Nesset, F. Rosenblum, R. Langlois, J. A. Finch

"Some sulphide mineral mixtures when exposed to air and a warm and humid environment can exhibit a self-generating temperature rise, referred to as self-heating or spontaneous heating. The observed self-heating derives from the oxidation reactions of the active sulphides. In previous publications by the authors, it was proposed that the self-heating of sulphides proceed in three distinct stages; namely, Stage A, Stage B and Stage C. In Stage A (<100OC) the sulphides, in the presence of moisture are oxidized, generating heat through a series of sequential reactions and forming elemental sulphur as one of the products. In Stage B (>100OC) the elemental sulphur produced in Stage A is further oxidized to generate additional heat and SO2. Stage C (>~380OC), sometimes referred to as thermal runaway or roasting, is not addressed in this paper. This communication focuses on the type and role of elemental sulphur found in Stages A and B, and the sequence of reactions that is occurring in Stage A. The sequence is divided into two phases, the first based on galvanic interaction between the sulphide minerals that generates an acidic environment but little heat, and the second involving the production of H2S which rapidly oxidizes to produce heat and elemental sulphur. To date, data suggest that the primary oxidation product formed in Stage A is the stable orthorhombic a-S8 form of elemental sulphur. Above 96OC the a-S8 transforms to a monoclinic ß-S8 structure which is less stable and will readily oxidize to generate heat and SO2. Above 159OC a proportion of the ß-S8 sulphur will transition to a polymeric Sµ form of sulphur which can readily volatilize. INTRODUCTION Some particulate and granular materials, when exposed to appropriate atmospheric and physical conditions, can exhibit a self-induced temperature rise resulting from accumulated heat due to internal exothermic oxidation reactions. This phenomenon is commonly referred to as self-heating or spontaneous heating. Under favorable physical and environmental conditions, these reactions can elevate the temperature of a given material from ambient to the point of auto-ignition. Self-heating behaviour should not be equated to pyrophoric behaviour which describes a group of materials (e.g. certain finely powdered metals) that will ignite spontaneously in air below 55OC. There are numerous materials such as coals, hay, forestry wood products, food products to name a few that can exhibit self-heating behaviour. This publication continues the focus of the authors on the self-heating of sulphide mineral mixtures. Many of the metals of commercial use found in nature are in the form of these sulphides which must be mined, crushed, ground and concentrated prior to smelting or hydrometallurgical processing in order to produce primary metal. The issues of sulphide self-heating therefore pertain to the mining and processing of metals."

Jan 1, 2018

By D. B. Hobbs, H. O. Burrows, T. D. Stay

Aluminum which has lost its original identity as to source may be considered as secondary. This would include scrap originating in the fabrication of aluminum, which is not consumed at the plant of fabrication, and all material resulting from fabrication, which has lost its original identity regardless of whether it be consumed at the plant of fabrication or not. In general, secondary aluminum may be divided into two classes, commercially pure and alloyed. The chief impurities found in commercially pure aluminum are copper, iron, titanium and silicon; while in aluminum alloys, copper, iron, titanium, silicon, zinc, manganese, magnesium, nickel, or tin, may be present in varying proportions. Occasionally lead and antimony are found in secondary aluminurn alloys, especially if the alloy results from remelting vender&apos;s automotive scrap. Such alloyed elements as are found in the scrap cannot be removed on remelting. In this, the remelting of secondary aluminum differs from the smelting of secondary copper or most other secondary metals. The majority of secondary materials reach the consumer in the form of remelt ingot or remelt No. 12 ingot. This ingot varies greatly in quality, depending upon the source of the material, and the manner in which it is refined and blended. The principal differences between primary and secondary ingot are: 1. The composition of secondary ingot may be more or less inclcfinite. 2. Secondary ingot may contain more dross and oxide. Secondary ingot may, however, be used successfully in a great itiany products. Relation of Primary Production to Secondary Production Table 1, compiled from data published by The Ameriran Metal Market, gives an approxirnatc idea of the relation of primary to srcondary production. Information obtained from other sources leads the authors to believe that the figures for secondary production are somewhat low.

By Gary Almeraris, Vincent Jr Tirolo

Traditionally, “Means and Methods” were the sole responsibility of Contractors. However, because of a number of litigious projects in the 1970s, Owners and their Engineers began including Suggested Methods of Construction (SMC) in Contract Drawings. By the late 1990s these SMCs were becoming baseline “Means and Methods” with Contractor recommended changes often considered as Value Engineering proposals. By 2004, the word “Suggested” was sometimes changed to “Prescriptive.” Owners are also purchasing TBMs and other mining equipment for Contractors prior to bid. Is limiting the contracting community’s innovation in developing their own “Means and Methods” and selecting their own equipment in the best interests of the Owner? Does it reduce the Owner’s, Engineer’s or the Contractor’s risk? Are claims reduced and finally what is the impact on the bid? A questionnaire was sent to more than fifty senior engineering field and management personnel representing more than 30 heavy construction companies to ask their opinion on these questions.

Jan 1, 2005

By George A. Roberts, Arthur H. Grobe

H. H. Hausner (Sylvania Electric Products Inc., Bayside, N. Y.)—I tested the 18-8 stainless steel powder described by Grobe and Roberts and the results were excellent. The powder was compacted and sintered in purified hydrogen to a very low density (approximately 20 pct and more porosity). Where the other powders show very little ductility when sintered to such a low density, the described stainless steel was surprisingly high in ductility. I would appreciate it if the authors could give us some data on a similar powder but without silicon and also data on 430 stainless steel powder. H. S. Kalish (Sylvania Electric Products lnc., Bay-side, N. Y.)—I should like to verify the excellent results obtained by Grobe and Roberts with their pre-alloyed stainless steel powder. It seems to me, however, that their data are conservative and that even better densities and higher tensile strength can be obtained with these powders by the selection of proper particle size fractions. The accompanying data were obtained by sintering compacts pressed from the powder made by Vanadium-Alloys Steel Co. to 0.8 in. in diam about % in. high in a cylindrical double action die without the use of lubricant. The compacts were sintered for 1 hr at 2370°F in hydrogen purified by passing it through a Deoxo unit (palladium catalyst) and a Lectrodryer. Even the density obtained using the as-received (—100 mesh) compacted at 40 tsi was quite high as was the hardness. This indicates that by increasing the sintering temperature slightly above 2350°F the coining and subsequent secondary sintering operation can be avoided. With the — 325 mesh fraction, however, very much higher density can be obtained and a high hardness. I have no tensile data to present, but I feel that it is not too optimistic to expect. that unusually high tensile strengths and good ductility can be obtained in this sintered material on the basis of the density and hardness data. The sintered stainless steel made by the above-described methods came out of the furnace very bright and clean. The purified hydrogen atmosphere is important in sintering stainless steel to reduce the oxide present in the powder. The result of such a sintering is good densification and good ductility of the sintered product. G. A. Roberts (authors&apos; reply)—We are greatly indebted to Messrs. Hausner and Kalish for their discussions of our paper. Their encouraging remarks are greatly appreciated and their confirmatory data will do much to add to the value of the paper. At the present time it is impossible to provide complete data on a similar stainless steel powder without silicon, but we do know that, in general, the properties are slightly inferior. Data on such a powder and on other stainless steel types are to be published in the near future.

Jan 1, 1952

By G. J. Ackland, K. Saksl, F. Brunke, M. Kohnke, B. Tegner, C. Siemers

The application of titanium alloys is limited to 550°C due to their poor oxidation resistance. It is known that the addition of niobium decelerates the oxidation of titanium alloys whereas elements like vanadium do not improve titanium’s oxidation resistance. The underlying mechanisms are not yet well understood. In the present study, different binary titanium-niobium and titanium-vanadium alloys as well as commercially pure titanium were investigated. Oxidation experiments were carried out at 800°C up to 288 hours followed by metallographic analyses to study the oxide layer morphology as well as the microstructure at the interface. Energy-dispersive X-ray spectroscopy mappings were used to identify possible changes in the distribution of the alloying elements. In addition, micro-focused hard X-ray experiments were performed to layer-wise analyse the phase composition in selected samples. As expected, the niobium containing alloys show a better oxidation performance compared to commercially pure titanium and the titanium-vanadium alloys. The oxide layer consisted of TiO2 and Ti2O3. Depending of the niobium content, a niobium-rich layer developed below the metal-oxide-interface minimising oxygen diffusion into the titanium matrix. Based on these results, the minimal niobium content needed for improved oxidation resistance was identified so that alloys of technical relevance can now be developed.

Jan 1, 2014

By Galen G. Waddell

This report describes a method of measuring and analyzing the initial deformation which occurs in the medium surrounding a mine accessway as the opening is created. Discussed are (1) the hypothesis upon which the research is based; (2) the in situ rock-deformation measuring equipment developed; (3) the field tests, consisting of measuring the deformation of the medium around two 4-foot-diameter raise bores as the boring progressed; and (4) a finite-element technique to correlate theoretical with experimental results, using elastic theory. Described also are the raise-bore operation and performance. The instrumentation developed proved to have the sensitivity and resolution necessary to measure rock deformation around a full-scale raise bore during excavation. Tests show the relationships of rock deformation to progress of the raise boring and to time. The initial deformation of the opening appeared to be elastic. Using the deformation records and an estimated field stress, the modulus of elasticity was determined for the rock mass. In addition, the importance of this type of measurement in assessing support-problem areas is discussed.

Jan 1, 1971

By F. G. Scott

This document is a proposed program plan for mining environmental research to be conducted by the U.S. Bureau of Mines in support of industrial oil shale mining and processing. This program plan is one of three research alternatives being considered by the Bureau, each based on a different level of anticipated funding. This report documents the low funding level program plan.

Jan 1, 1980

By C. Fairhurst

Most of the papers designated as being within the topic of underground storage at this Symposium are concerned with aspects of radioactive waste isolation. Although this is, unquestionably, an important international application of underground storage, and one involving a considerable number of research investigations, the subject of underground storage is indeed much broader. Several major international conferences have been devoted exclusively to it. Applications include storage, under a range of temperatures and pressures, of oil and liquefied petroleum products, compressed air, heat, foodstuffs of various kinds, hazardous and &apos;nuisance&apos; industrial by-products, and a variety of special applications, both civilian and military - some in use, others proposed. Storage may be in caverns excavated specifically for the purpose, exhausted mines may be adapted for storage or, in some cases, the material to be stored may be injected under pressure into the pore spaces of porous-permeable formations at depth. A variety of rock types and geological environments are used, e.g. excavations in salted or domal salt, where long-term creep closure of the openings is a concern; massive granite, where fluid loss through fissures may be important. Cavities may have spans of several tens of meters, and there is interest in achieving still larger excavations. As would be expected, this breadth of underground storage applications introduces a similarly broad range of questions in rock mechanics and rock engineering. The report will review these questions and recent developments in rock mechanics research, computational procedures, and design applications - and will also discuss the opportunities for a still greater range of applications of underground storage to current industrial and social problems.

Jan 1, 1989

By Forrest T. Moyer

The safety record of the coal-mining industry in 1968 worsened appreciably .in fatality experience but was slightly better in nonfatal-injury experience. Work fatalities in 1968 totaled 311 and occurred at a frequency rate of 1.33 per million man-hours or worktime. The fatality total was 89 higher, and the rate of occurrence was 45 percent higher than the corresponding figures of 222 fatal injuries with a frequency rate of 0.92 in 1967. The worsened fatality record in 1968 resulted primarily from two major disasters (a single accident which results in the death of five men or more) which killed 87 men, nine in one and 78 in the second. The total of 9,639 nonfatal injuries was the lowest annual figure in complete records back to 1930. The frequency rate of 41.12 nonfatal injuries per million man-hours of worktime for 1968 was the second lowest annual rate of occurrence. The severity rate of all injuries, 10,513 days lost or charged per million man-hours, and the average severity, 248 days lost per injury, in 1968 were the worst annual data in the series started in 1944. Total worktime of 234.4 million man-hours and coal output of 553.3 million tons in 1968 were, respectively, 3 and 1 per- cent lower than in 1967.

Jan 1, 1972

By Amy B. Cerato

The application of this study is to use helical anchors as a foundation system for small wind tower (1 ? 10 kW) guyed cables. Helical anchors are currently used to anchor guyed cables of telecommunication and electric towers. However, the increased dynamic vibrations a wind turbine adds to the tower and foundation system under working loads, as well as extreme environmental conditions (e.g., straight line winds, ice load or sudden furling shocks), require additional knowledge about the behavior of helical anchors. These field conditions were simulated in this study by instrumenting a working tower with load cells and 3-axis accelerometers to gather data on wind speed and tower response. These tower responses were then transmitted to the helical anchors through an extensive, large-scale testing program that included monitoring the performance of the helical anchor foundation under dynamic loads, subject to natural variations in both wind regimes, precipitation (water level) and variations in helical anchor geometry. This paper specifically discusses the effects of helical anchor geometry on helical anchor performance under long-term dynamic loads.

Jan 1, 2008

By L. Yuan

To reduce fire hazards from spontaneous combustion of coal in longwall gob areas, a series of computational fluid dynamics (CFD) simulations were conducted by National Institute for Occupational Safety and Health (NIOSH) to model the spontaneous heating of coal in longwall gob areas. The previous modeling results demonstrate that spontaneous heating of coal usually occurred behind the longwall shields and along the face with a bleeder ventilation system. Assuming a stationary longwall face, the spontaneous heating could turn to a spontaneous fire in several days for the most reactive coal under favorable conditions. When the longwall face advances, the spontaneous heating process will be significantly affected. In this study, the effect of longwall face advance on the spontaneous heating in the gob area is investigated using the CFD model developed in previous studies. One longwall panel with a bleeder ventilation system is simulated. The width of the panel is 300 m, while the length of the panel is changed between 1,000 to 2,000 m. The same permeability and porosity profiles are used for gobs with different lengths. The spontaneous heating first develops in the gob when the longwall face is stationary. Then, the face advances at a certain rate. The face advance is simulated as a series of discrete movements, and the effect of the face advance on the maximum temperature developed during the face stoppage is examined. Disclaimer: The findings and conclusions in this report are those of the authors and do not necessarily represent the views of the National Institute for Occupational Safety and Health.

Jan 1, 2009

By John G. Henning

The Porcupine Joint Venture operates the Dome Mine in South Porcupine, Ontario. Dome underground began production in 1910. It is the longest continuous operating gold mine in Canada, producing in excess of 15 M ounces. More than 900 underground stopes have been mined and hundreds of miles of drifts, sublevels and raises developed. Underground mining methods included shrinkage, cut and fill and longhole. Not all stopes were backfilled upon completion, particularly the longhole stopes. The Dome open pit was designed above the underground mine workings such that, as the pit is excavated, it intersects underground drifts and stopes. Potential operational problems associated with the interactions between the stopes and the pit walls may occur, necessitating pit wall redesign, ground support installation and operational rescheduling. Each intersection of the pit with the underground mine workings is closely evaluated to maintain a safe working environment and wall stability. This paper discussed how risks to pit wall stability are assessed, mitigated and monitored.

May 1, 2004

By F. E. Heuze

This article deals with the effects of high-explosive and nuclear explosions in rock masses. We first highlight the strong influence of geological discontinuities, such as joints and faults, on ground motion characteristics. Then, we briefly introduce the Discrete Element Method, as a new technique for numerical simulations. II is shown to be far superior to continuum-based approaches, when dealing with the dynamics of discontinuous media such as jointed rocks. Finally, we simulate the ground effects from a generic contained nuclear explosion, which bears some similarity to the SHOAL event in granite. This calculation is intended to emphasize the influence of the near-source geology on the distribution of energy, and on the motion at various azimuths in the medium.

Jan 1, 1991

By E. Z. Manos

The Detroit salt mine is operated by the Detroit Salt Co. It is one of the oldest underground room-and-pillar mines in the United States still in production. Mining at the Detroit salt mine began in 1906 with the sinking of the No. 1 shaft. Mining continued through the years, becoming progressively more modern in its equipment and techniques, until it was closed in 1983. In 1997, after a period of care and maintenance, the newly formed Detroit Salt Co. decided to reopen the mine. Upon completion of an extensive rehabilitation program, salt production resumed in 1998. Production currently continues at a rate of 910kt/a (1 million stpy). To date, the Detroit salt mine has mined more than 45 Mt (50 million st).This mine is unique because it lies under a heavily urbanized area within metropolitan Detroit. The mine and its history make a good case study for the continuing coexistence between the mining industry and its environs.

Jan 1, 2003