Search Documents

Producers with Zero Reportables 2007!: ?New Horizon Mine, Western Fuels Colorado LLC ?Isaacs Run HWM, ICG ADDCAR Systems, LLC ?Savage Mine, Westmoreland Savage Corporation ?South Hallsville No 1 Mine, Sabine Mining Company ?Black Butteand Leucite Hills, Black Butte Coal Company Black Butte and Leucite Hills, Black Butte Coal Company ?Buckskin Mine, Kiewit Mining Group ?Coal Creek Mine, Thunder Basin Coal Company, LLC

Jan 1, 2008

By A. George Stern

[In the examination of bentonitic clay suspensions used for oil-well drilling fluids3/ (and for other purposes, such as a core binder for foundry sand) it is important to have comparative tests for evaluating them. A satisfactory clay for these and other purposes should have the property of forming what is commonly called a "gel," but the measurement of this property has been a real problem. To date the solution has not been satisfactory, and some of the difficulties are considered in, this, paper, which describes a simple form of instrument (identified as an eykometer) for measuring the yield point under hydrostatic conditions of non-Newtonian clay suspensions, including those muds that are thixotropic. An oil-well drilling mud serves several functions, many of which depend on the "gel" characteristics of the mud. Among the more important functions are: (a) To plaster the sides of the hole to prevent caving of the walls; (b) to prevent the loss of the circulating fluid out of the hole by seepage; (c) to carry sand and cuttings out of the hole to the surface as they are formed by the rotary drill; and (d) when circulation of the fluid stops for shut-down or other unavoidable cause, to hold the cuttings in suspension by the setting up of the gel, thereby avoiding the difficulties that result when these cuttings are allowed to fall through the fluid and pack at the bottom of the hole.]

Jan 1, 1940

By A. George Stern

In the examination of bentonitic clay suspensions used for oil-well drilling fluids3/ (and for other purposes, such as a core binder for foundry sand) it is important to have comparative tests for evaluating them. A satisfactory clay for these and other purposes should 'rave the property of forming what is commonly called a "gel," but the measurement of this property has been a real problem. To date the solution has not been satisfactory, and some of the difficulties are considered in, this, paper, which describes a simple form of instrument (identified as an eykometer) for measuring the yield point under hydrostatic conditions of non-Newtonian clay suspensions, including those muds that are thixotropic. An oil-well drilling mud serves several functions, many of which depend on the "gel" characteristics of the mud. Among the more important functions are: (a) To plaster the sides of the hole to prevent caving of the walls; (b) to prevent the loss of the circulating fluid out of the hole by seepage; (c) to carry sand and cuttings out of the hole to the surface as they are formed by the rotary drill; and (d) when circulation of the fluid stops for shut-down or other unavoidable cause, to hold the cuttings in suspension by the setting up of the gel, thereby avoiding the difficulties that result when these cuttings are allowed to fall through the fluid and pack at the bottom of the hole.

Jan 1, 1940

By Alan A. Campoli

The U.S. Bureau of Mines evaluated two different conventionallongwall gate entry systems in the Southern Appalachian Basin, where mining and geologic conditions are conducive for coal pillar bumps. These gate entry systems were in a coal mine located in the Pocahontas No.3 Coalbed under approximately 2,000 ft of overburden and a massive quartzite sandstone member, and both employed a center abutment pillar flanked by yield pillars. The 8O-ft-square tailgate abutment pillars within the first study area began bumping 500 ft in advance of mining. This was accompanied by face bumps on the tailgate corner of the longwall face. The 120-by 180-ft tailgate abutment pillars within the second study area did not begin to bump until mining was approximately 100 ft past. Coalbed stress change and abutment pillar dilation data demonstrated that a 15-ft-wide perimeter of yielded coal surrounded a highly stressed core in both sizes of abutment pillars. The 62 pet more core area per foot of gate entry in the larger abutment pillars prevented excessive load transfer to the corner of the tailgate panel and eliminated the face bumps experienced with the original gate entry design.

Jan 1, 1990

By John C. Machisak

STATISTICAL data on injuries and employment pertinent to metal mines and to their mills, and/or processing plants are presented in this Information Circular for the calendar year 1960. The information pertains to metal mines, as well as ore-dressing plants and primary nonferrous smelters, refineries and reduction plants, and their auxiliary works. These data are voluntarily submitted annually to the Bureau of Mines by the operators, and contribute greatly toward the promotion of safety in the mineral industries. The data presented are classified according to the principal mineral produced and include information on copper, iron, lead-zinc, gold-silver lode, gold placer, uranium-vanadium and miscellaneous metals. A breakdown of miscellaneous metals by commodities is shown in table 19, page 41. The data also relate to workers engaged in production, exploration, development, construction, and maintenance and repair work, as well as supervisory personnel and office- workers at the mine or plant site. Injury and employment data at metal mines and metallurgical plants in the United States for 1960 are shown under the following general sections:

Jan 1, 1963

By Randy R. Huberty

Although originally designed with deep foundations consisting of all driven steel H piles and drilled caissons, a unique application of Augered Cast-in-Place (ACIP) piles as an alternate design resulted in a significant cost savings for the Midfield Terminal Project at the Pittsburgh International Airport. The project was enormous in scope covering an area two miles long by one mile wide, with changes in elevation of over 200 ft. The varying geology combined with the large amounts of fill required resulted in a complex set of geotechnical design parameters that had to be evaluated through both load testing and analyses. A total of almost 400,000 lineal feet of ACIP piles were installed for this project.

Jan 1, 2001

By Krogerus. H., P. Jokinen, T. Lintumaa

Keywords: Pyrometallurgy, furnace, coke, smelting charge, optimization, ferrochrome The main consumer of ferrochrome is stainless steel production. Stainless steel must maintain a reasonable price against other competitive materials. Therefore, the ferrochrome price must be low enough and profitable for the producers of stainless steel. The investment and operational costs of ferrochrome production are greatly dependent on the availability of the process and the production rate. Thus the furnace size and production rate in submerged electric arc furnaces will be greatly increased in the near future. The ferrochrome production per furnace, e.g. at Outokumpu?s Tornio Works, increased from 30 000 t/a to 165 000 t/a in about 35 years. The same trend will continue globally but now much more quickly. The Outokumpu ferrochrome process at Tornio Works uses sintered chromite pellets and upgraded lumpy ore as a chromite source. Metallurgical coke is used as a reductant. Reliable smelting in a large furnace demands the correct charge composition and well-known characteristics of the charge components. The quality and electrical conductivity of cokes (normally used) has the most important role for the electrical conductivity of the smelting charge. The results of the measured electrical conductivity of different cokes and the smelting charge with many controlling factors are presented here. These measurements were performed over the years for our own purposes at the laboratory of Outokumpu Research Oy (ORC), in Pori, Finland.

Jan 1, 2006

By Martin C. Jones

This paper outlines the development of small diameter grouted piling, to deal with foundation problems in difficult soils conditions and in very restricted access areas. A number of applications are outlined to show the way in which these piles have been used over the last sixteen years in Canada. PICKERING GENERATING STATION - ONTARIO HYDRO UNDERPINNING OF SCREENHOUSE - TRASH DISPOSAL AREAS Between 12th July and 29th September 1971, 40 small diameter grouted piles were installed in the screenhouse at Pickering Generating Station. Access was extremely restricted as the screenhouse had been completed and the majority of mechanical equipment had been installed. The two ends of the screenhouse had been built on granular fill which overlies till and shale bedrock and settlements had been observed which it was decided had to be halted even though the rate of subsidence had decreased. Two diamond drills were employed to install 8 inch

Jan 1, 1987

By Harry D. Lewis

Gilsonite is a lustrous black material that can be easily crushed into a chocolate-colored powder. It is a solid but relatively soft, lightweight hydrocarbon that visually resembles the volcanic glass obsidian. It was once thought to be a type of coal, but because it is thermoplastic it melts rather than bums. Gilsonite is found in commercial quantities only in the Uinta Basin of eastern Utah and western Colorado, where it forms vertical, nearly parallel veins of varying depth, width, and length. Gilsonite from different veins has different properties, most notably variations in softening point and solubility. These differences result in its use in a variety of industrial applications. Gilsonite's earliest commercial uses were in varnishes, buggy paints, and beer vat linings. Eventually it came to be used in more than 160 products ranging from inks to explosives. It is exported from the United States to most industrialized countries throughout the world. Today, due to competition from synthetics and other hydrocarbon products, its use has narrowed to several specific industries. Although sold mostly as a commodity, current research is focused on applications for gilsonite as a value added product. Historical Overview The discovery of gold in California and the dawn of the mining era in Nevada, Colorado, and Utah around 1850 brought a wave of prospectors to the western United States. One of those pioneers, Samuel H. Gilson, is generally credited with a major role in the discovery of gilsonite. The material now known as gilsonite was discovered several times from the late 1860s through the mid-1880s. It was William P. Blake who, after receiving samples of the material, wrote a paper in 1885 describing "a new variety of asphaltum from the Uinta Mountains." He termed the material uintaite. Although Sam Gilson was not the first to discover the mineral, he was an-inventor who used gilsonite in products that he patented. It was his conviction that the substance was of great value, which caused some to refer to it as gilsonite. The term Gilsonite became the registered trademark of the American Gilsonite Co., and it continues to be in use today. When the first company was formed to mine this substance in 1886 it was named the Gilsonite Manufacturing Co. This firm acquired many gilsonite mining claims and marketed a varnish made from the material. It was the unusual properties of gilsonite varnish that attracted the attention of Adolphus Busch of the Anheuser-Busch Brewing Co. In 1889 Anheuser-Busch bought out Gilson's interests and formed the Gilson Asphaltum Co. Busch had been importing asphalt from Sicily for use in lining beer barrels and saw gilsonite as being more readily available and cheaper. Although gilsonite did not work well in this application, Busch did acquire a large number of mining claims in the Uinta Basin. In 1903 the parent firm of Gilson Asphaltum financed the building of an 85-km railroad from near Grand Junction, CO, to Dragon, UT, to haul gilsonite ore to market. Underground mining was initially centered near Dragon and then later at Bonanza, UT, as different veins were mined. The railway was abandoned in 1937 in favor of truck transportation. In 1938 Gilson Asphaltum changed its name to Barber Asphalt Co., the predecessor of Barber Oil Corp. In 1946 Barber Oil teamed with Standard Oil of California to form a partnership, American Gilsonite Co., which today has its operational headquarters at Bonanza, UT. Barber Oil investigated many new uses for gilsonite, including the making of petroleum derivatives such as gasoline. This work led to the construction of a 116-km pipeline to carry slurried gilsonite to a refinery in Colorado for the production of gasoline, fuel oil, and coke. Pipeline operations began in 1957 but stopped when the economics of competing with petroleum became unfavorable, and the refinery was sold in 1973. In 1981 Standard Oil (later Chevron) became the sole owner of American Gilsonite and remained so until 1991, when it sold its interest to Stratford Enterprises Co. of Tulsa, OK. The companies have since been merged and now operate under the name American Gilsonite Co. with headquarters in Salt Lake City, UT. American Gilsonite continues to be the world's largest miner and supplier of the mineral. The American Asphalt Association was formed in 1902 by former stockholders in Gilson Asphaltum. This company mined various gilsonite claims until it was dissolved in 1953 and its properties were sold to American Gilsonite and Gordon S. Ziegler and Associates. The Utah Gilsonite Co. was established in 1920 and mined several claims until 1952, when its holdings were sold to Gordon Ziegler. Several other gilsonite mining ventures have been pursued in Utah, although they were significantly smaller in scale than those described above. There are currently three companies which mine gilsonite resin in Utah. They are American Gilsonite Co., Ziegler Chemical & Mineral Corp., and Lexco.

Jan 1, 1994

Coal Preparation Research at Turkish Coal Enterprises (TKI)

Sep 13, 2010

By T. P. Mucho

Over the past several years, two types of roof control problems have been en- countered at Beth Energy's Eighty Four Complex mine in Southwestern Pennsylvania. These problems have been (1) poor roof conditions encountered while advancing submain entries and longwall panel entries and (2) deterioration and failure of long- wall gateroads, principally the tailgate entry. This paper discusses the efforts by mine personnel to analyze the origins of the various attempts to-deal with the problems, and the success (or failure) of these efforts. Highlighted are the use of various common roof Control materials, variations in mining techniques, cementatious pillars, and changes in pillar design using yield and abutment pillars to address these problems.

Jan 1, 1986

The gold concentration profiles which develop inside the activated carbon particles during the adsorption process were measured, so as to obtain additional direct proof of intra-particle mass transfer rate-control and to determine how individual carbon particles in a population vary in their gold uptake behaviour. The observed gold concentration profiles inside the activated carbon particles were typical of situations where an intra-particle mass transfer mechanism is rate-controlling. Gold di-cyanide penetrated the carbon particles with a wave-like front until it was uniformly distributed throughout the particle. This corresponds with the profiles predicted by the film and surface diffusion model. However, the rate with which gold di-cyanide was transported inside the individual carbon particles varied within the population of carbon particles. This variation was characterized by a lognormal distribution in surface diffusivity. Because the estimated variances of these surface diffusivity distributions were small, the dynamic adsorption behaviour of the carbons used in the present study did not deviate significantly from that predicted by a model based on film mass transfer and a single surface diffusivity. Van Deventer (1984, 1985 and 1986a) reported data that could not be adequately described by a model based on film mass transfer and a single surface diffusivity. In this study a model based on film mass transfer and a wide lognormal distribution of surface diffusivity values was applied to his data. It was shown that a population of carbon particles with a wide distribution in surface diffusivity values could offer an alternative explanation to the mechanism proposed by Van Deventer which was based on film mass transfer, with partitioning of the carbon into micro- and macropores with surface diffusion in the macropores and slow mass transfer into the micropores.

Jan 1, 1997

By Cary Hirner

The Metropolitan Water Reclamation District of Greater Chicago (District) is in the final phase of completing the Calumet System component of the Tunnel and Reservoir Plan (TARP) by bringing the Thornton Composite Reservoir online by 2014. The Thornton Composite Reservoir will provide nearly 30 billion liters (7.9 billion gallons) of additional storage for minimization of combined sewer overflows(CSO) and flooding in the Chicago metropolitan area. The project requires that the existing 6.7 m (22 ft) diameter Thorn Creek tunnel conveying overbank flood flows is re-routed and connected to the Thornton Composite Reservoir. This paper presents the components of the Thornton Composite Reservoir and specifically the detailed evaluation of a drill-blast tunnel. Other project features include an access shaft, control gate, energy dissipating structure, bulkheads, and live tunnel connection. The construction contract will be procured in late 2009.

By Stephanie Price

Engineering Associations ?Regulatory authority ?License individuals and firms ?Discipline licensed members ?Enforce against improper acts ?Programs for EIT?s, competence, etc

Oct 1, 2010

MR. W. E. WAINWRIGHT occupied the chair, and in introducing the lecturer said, on account of the absence of the vice-president, it fell to his lot to introduce the lecturer. Mr. Tennberg, he said, was visiting Australia, and those present might wonder who he was.He understood that the lecturer w~s a reputable practising geophysicist, associated with a reputable company! It was rather desirable perhaps to say that the Institute had made some inquiries with regard to his status. Geophysics was a comparatively newscience, and had suffered several hard knocks in Australia and elsewhere. Most of those knocks had been the result of undue optimism of a number of people who did not understand what they were talking about. It had been claimed that geophysics was a...

Jan 1, 1930

By Stephen C. Tadolini

PC-Strand tendons, commonly referred to as cable bolts, have become a major rock reinforcement device for underground mining and civil applications. The most common configuration is a 1+6 strand, which designates a center king-wire, with six outer wires wound around it to form a 0.6-in (15-mm) diameter cable. The capacity of this tendon approaches 30 tons, but the performance is largely dependent on the anchorage medium and the ability of the system to transfer stresses back into the rock mass while reinforcing and suspending the immediate roof. Recent developments to improve the transfer mechanisms of the PCstrand via the anchorage medium by impregnating the individual wires with uniquely designed deformations have resulted in improved anchorage and subsequent cable bolt performance. This paper describes a series of laboratory tests used to develop the initial indentation patterns and numerical modeling simulations that were undertaken to refine and optimize the final designs. The new, indented PC-Strands, offered in both bright and properly galvanized, have been tested in the field and are being used effectively in two new cable bolt products. The results of the laboratory, computer modeling, field testing and in-situ installations provide a glance at the next generation of cable bolts. This suite of testing shows how they will improve the safety and serviceability of openings under adverse ground conditions.

Jan 1, 2012

By John C. Machisak

STATISTICAL data on injuries and employment pertinent to metal mines and to their mills, and/or processing plants are presented in this Information Circular for the calendar year 1960. The information pertains to metal mines, as well as ore-dressing plants and primary nonferrous smelters, refineries and reduction plants, and their auxiliary works. These data are voluntarily submitted annually to the Bureau of Mines by the operators, and contribute greatly toward the promotion of safety in the mineral industries. The data presented are classified according to the principal mineral produced and include information on copper, iron, lead-zinc, gold-silver lode, gold placer, uranium-vanadium and miscellaneous metals. A breakdown of miscellaneous metals by commodities is shown in table 19, page 41. The data also relate to workers engaged in production, exploration, development, construction, and maintenance and repair work, as well as supervisory personnel and office-workers at the mine or plant site. Injury and employment data at metal mines and metallurgical plants in the United States for 1960 are shown under the following general sections: 1. General injury experience: Tables I-5-Data on injuries, injury-frequency and severity rates and related employment data, work location, and degree of injury.

Jan 1, 1963

The Illawarra District, from 50 to 100 miles south of Sydney, is one of the State's important coalfields. It extends from Clifton on the north, to the Shoalhaven river on the south, and from the coast westward beyond the coastal scarp.For descriptive purposes, this area falls naturally into two zones:(a) the coastal belt backed-by the eastern edge of the plateau;(b) the plateau, westerly from the coastal scarp.(a) The Coastal Belt.A triangular shaped area extending from Clifton to the Shoalhaven river, composed for the most part of soft coal measures strata of Permian age, which, on weathering, undermines the massive overlying Mesozoic sandstones and causes the gradual recession of thecliffs.South of Wollongong, upper marine sediments and contemporaneous igneous rocks make their appearance beneath the coal measure beds and occupy the greater portion of the coastal belt.(b) Plateau Area.Extending westerly from the coastal escarpment is a plateau known as the Robertson Tableland, composed of Triassic sandstone and shales dipping gently in a northerly direction, and capped in places by Wianamatta. shales and r.rertiary basalts. This tableland is approximately 2400 feet above sea level in the vicinity of Robertson, and gradually falls to about 750 feet at Waterfall.The plateau area for the most part is highly dissected, rough, steep gorges alternate with sharp ridges.A large part of the northern watershed of the Robertson tableland is a reserve for Sydney water supply, and large dams have been constructed at Cataract, Avon, Burke, and Cordeaux.

Jan 1, 1938

By J. C. Carrasco, M. Sánchez, R. Jara, F. Marquez, F. Parada, R. Parra, J. Palacios

In past years, Chile has been the largest copper producer in the world and for 2002 mining represented country average of 10 % of the GDP, accounting for 47 % of the total exportation. As copper sulphides are the main mining resources in the country, the metal is produced using the classical processes of flotation and pyrometallurgical extraction. Seven copper smelter plants, which extends from the northern Atacama desert to the central part of the country produced1,522,000 metric tons of fine copper in 2002, approximately one half of total copper concentrate production, with a notorious environmental impact due to the great amount of slag produced during these extraction steps. In this work, a global characterization of copper pyrometallurgical slags produced and disposed of in Chile and worldwide is done, and the concept of total project development is considered to explain the scopes of the study, recovering different compounds and generating new activities around mining. The presentation is completed with the proposal of various methods and techniques being developed today in a joint project between smelter plants and the University of Concepción, with the support of the Chilean government and mining companies, addressed to generate new materials from copper slag. Recovery of copper, molybdenum, precious metals, silica and iron, that is the most abundant component of the slag, are the goals for this research. Metals, commercial compounds, alloys and different forms of iron oxides for steel industry are proposed products.

Jan 1, 2004

By E. Marcoux, F. Lotfi, A. Belkabir, L. Maacha, A. C. Brown, S. Brunet

"Koudiat Aïcha is a small Zn-Pb-Cu deposit, enclosed in the Visean Sarhlef volcano-sedimentary series of the Moroccan Hercynian Jebilet massif. Base metal mineralization is located between a basal unit consisting of black argillite with arenite intercalations, and an upper unit composed of black argillite with locally fossiliferous calcareous units towards the top. Paraconcordant gabbro sills are present in both the upper and basal units, and the enclosing strata. Three successive phases of deformation linked to regional deformation overprint the volcano-sedimentary rocks and gabbros, as well as the sulfide mineralization.The mineral deposit includes several lenses of massive to semimassive pyrrhotite, 1 to 20 m thick, with a large halo of disseminated sulfide veinlets and sulfide nodules within a zone of intense chlorite alteration in the footwall. The ore mineralogy consists of massive to semimassive pyrrhotite with lesser amounts of sphalerite, chalcopyrite, arsenopyrite, galena, pyrite, and stannite.Lead isotope results (206Pb/204Pb averaging 18.27) suggest that the metals of the Koudiat Aïcha deposit are derived from the volcano-sedimentary host rocks. Sulfur isotopes also indicate a volcano-sedimentary origin, with bacterial reduction of sulfate (d34SCDT = -7.5‰ to -10.5‰). The conditions for sulfide meta-morphic equilibration range from 250° to 330°C (sphalerite and chlorite geothermometers). The gabbroic sills could have been a local heat source for hydrothermal circulation. Based on these geological and mineralogical features, a Besshi-type model seems appropriate for the genesis of the Koudiat Aïcha mineralization.Koudiat Aïcha est un petit dépôt de Zn-Pb-Cu, encaissé dans la série volcano-sédimentaire Viséenne de Sarhlef dans le massif Hercynien de Jebilet au Maroc. La minéralisation en métaux usuels se situe entre une unité basale d’argilite noire interlitée d’arénite et une unité supérieure composée d’argilite noire comprenant localement des calcaires fossilifères près de son sommet. Des sills de gabbro paraconcordants sont présent à la fois dans les unités basale et supérieure, ainsi que dans les strates environnantes. Trois phases de déformation successives associées a la déformation régionale superposent leurs effets sur les roches volcano-sédimentaires, les gabbros, ainsi que la minéralisation sulfurée. Ce gîte comprend plusieurs lentilles de pyrrhotite massive a semimassive de 1 a 20 m d’épaisseur au sein d’un large halo de veinules de sulfures disséminés et en nodules au sein d’une zone intensément chloritisée dans le mur du gisement. Le minerai consiste en pyrrhotite massive à semimassive avec des quantités subordonnées de sphalérite, de chalcopyrite, d’arsénopyrite, de galène, de pyrite, et de stannite. Les résultats de l’analyse des isotopes du plomb (206Pb/204Pb moyen de 18.27) suggèrent que les métaux du gîte Koudiat Aïcha proviennent des roches volcano-sédimentaires encaissantes. Les isotopes du souf¬fre indiquent eux-aussi une origine volcano-sédimentaire, impliquant la réduction bactérienne des sulfates (d34SCDT = -7.5‰ et -10.5‰). L’équilibration métamorphique des sulfures s’est produite entre 250° et 330°C (géothermomètres à sphalérite et chlorite). Les sills de gabbro pourraient avoir été la source de chaleur locale responsable de la circulation hydrothermale. Sur la base de ces caractéristiques géologiques et minéralogiques, il semble approprié d’invoquer un modèle de type pour Besshi pour expliquer la genèse de la minéralisation de Koudiat Aïcha."

Jan 1, 2008