Search Documents

By G. W. Poling

This paper evaluates current environmental protection legislation, guidelines and criteria, focusing mainly on the land and water disposal of mill tailings. Effluent criteria and regulatory mechanisms are proposed, and submarine tailing disposal is discussed at length. The importance of basing regulations on the best available rationale is stressed.

Jan 1, 1979

By Andreas Hucke

For the roadway design in the German hard coal mining industry, an advanced combined planning system has been applied during the past 20 years. The German mining industry is working with single entry roadways system. After first longwall passage the roadways will be stabilised with side wall building material packages. Later this roadway will be used again for the second retreating longwall. The intention of the implementation of several different design methods for the planning of the roadways is to enhance the reliability of the results. On one hand the planning system uses numerical simulation and physical modelling in addition to analytical and empirical methods. On the other hand in-situ monitoring and analysis during the roadway development will be used to verify and calibrate the numerical and physical models. Especially before the implementation of new support elements in underground, this system is suitable and reasonable because the new support elements will be tested in the physical and numerical simulation prior to cost intensive underground tests. The interaction between the numerical and physical modelling in comparison with underground monitoring and analysis during development and the later use of roadways will be shown with some examples. The first example shows a rock bolted rectangular roadway which will be mined at both sides of the roadway. Different support and roadway building material package systems are investigated under various stress conditions. The results are utilised to optimise the roadway support and the roadway side package systems. The influence of different points in time of the installation of several support elements in a combined arch and bolted roadway is shown as another example. Two different types of support systems are compared within the physical models. These models are used as a base for ongoing numerical analysis and simulation to find out the ideal point of time to assemble the different support elements. The last example handles the influence of slickensides in the roof of arch shaped roadway on their stability. Different slickenside positions and densities are investigated and classified.

Jan 1, 2006

By Mauricio Monteiro Machado, Neyda de la Caridad Om Tapanes, Ana Isabel de Carvalho Santana, Rodolfo Salazar Perez, Rodrigo Ribeiro Soares, Roberta Gaidzinski

Vasos de pressão são equipamentos empregados nas mais variadas indústrias, sendo responsáveis por significativa parcela do orçamento. Os materiais mais utilizados para a construção de vasos de pressão para a indústria de óleo e gás são as ligas de aço carbono e em alguns casos se justifica o emprego de ligas de aços inoxidáveis. O objetivo deste trabalho foi estudar as características dos vasos de pressão, materiais de fabricação e o custo de aquisição de vasos de pressão por parte da Petrobras. Para o desenvolvimento foram utilizadas duas ferramentas de processamento de dados: a Lei de acesso à informação que permitiu a criação de uma base de dados, e o Planejamento de experimentos que possibilitou avaliar a influência do tipo de material e outras variáveis sobre o preço do vaso de pressão (variável de resposta). Os resultados estatísticos demonstram que, para as faixas analisadas o comprimento entre tangentes (CET) e o Diâmetro (D) possuem uma influência estatística direta sobre a variável de resposta Preço. Finalizando, o estudo conseguiu conciliar aspectos construtivos com os fatores financeiros, sendo de grande valia para os fabricantes de vasos de pressão.

Aug 1, 2019

By Trevor Hamm, Nick Holl

"Cameco Corporation is operator of the world's richest uranium project, the Key Lake mine/mill complex, located within the Athabasca region of Northern Saskatchewan. Mineable resources from the Key Lake ore bodies with an average U,08 content of 2.5% will be exhausted by the year 2000 and open pit mining at Key Lake will be phased out at that time. The mill will continue to operate at increased capacity, using high grade ore from the McArthur River project, a new underground mine at a distance of about 80 km from the Key Lake site. The McArthur River ore with an average U308 content of about 15 % will be blended with separately stockpiled low grade materials from Key Lake with a U,08 content of about 0.1 %. The average (blended) mill feed grade will be about 4%, similar to peak concentrations found in Key Lake ore.The Key Lake ore tailings are presently being placed in the mined out Deilmann pit under sub-aerial conditions, using spigots and a highly efficient pit/tailings drainage system. The tailings resulting from the processing of the blended McArthur River ore will be deposited on top of the Key Lake ore tailings under sub-aqueous conditions. This staged approach shows distinct technical and environmental advantages over an alternative, fully sub-aerial in-pit deposition scheme.The first part of this paper presents an overview of site specific geotechnical and hydrogeological features found at Key Lake and details some of the extensive test and modelling work that was required for environmental impact predictions during the development phase of the facility. The second part of this paper deals with tailings modifications, innovative placement technologies and drainage methods that have been (and will be) employed at the Deilmann Tailings Management Facility {TMF) to produce a highly consolidated tailings body under non-buoyancy conditions. The application of this technology at Key Lake is expected to produce a tailings ""plug"" in the Deilmann TMF which will have a permeability similar to or lower than the original in-situ Deilmann ore, resulting in a minimization of contaminant mass loadings to the environment both during operation and after decommissioning."

Jan 1, 1998

By Ernest J. Conway

Seventy-four human factors research and development projects were identified for possible Bureau funding. The projects were based on (1) literature surveys, (2) reviews of accident statistics and reports, (3) interviews with equipment manufacturers, MSHA, and Bureau personnel, and (4) site visits to 26 mines. The projects are divided into the following categories: those related to (1) mobile equipment, (2) maintenance shops and areas, (3) plants and mills, (4) organizational factors, (5) safety programs/data, and (6) training. The projects were rated by industry and MSHA people in terms of benefit to the industry. Projects were placed into three categories of priority. The highest priority contained 25 projects with 26 in Category 2, and 23 projects in the lowest category.

Jan 1, 1982

Three methods of gold analysis are briefly described highlighting some of the problems and advantages of each. The variation of results between samples and splits and due to method of preparation is illustrated. The mean per cent difference of the fire assay values from the means of sample split values for three cases is 15 per cent.Finally, a comparison of the aqua regia leach atomic absorption spectroscopy (AAS) and fire assay fusion AAS techniques is made.This shows that the mean precision, the ability to obtain the same value, of the methods at 98 per cent confidence is ± 30 per cent and ± 15 per cent respectively. The fire assay fusion AAS method is relatively more accurate than the aqua regia one.

Jan 1, 1984

By Juan Ayza

Ante el peligro de la concentración y exposición de los polvos de sílices en el personal minero, el presente texto revisa la silicosis -en tanto determina las propiedades de los polvos en reacción y su relación con los medios para detectarlo. Asimismo este estudio constituye en un problema de mecánica de fluidos, donde las operaciones más peligrosas se evidencian en la perforación y explosiones. También se refieren algunos datos sobre los costos de profilaxis de la silicosis y de las indemnizaciones de los enfermos.

Oct 1, 1955

Uranium exploration over a wide area of the Southern Frame Embayment, South Australia, has defined a number of Lower Tertiary fluvial palaeochannels incised in older rocks. The buried channels contain similar stratigraphicsequences of interbedded sand, silt, and clay, probably derived from the adjacent uranium-rich Olarv Provinee. Uranium mineralization is pervasive within two major palaeochannels, and four small uranium deposits have been found in the basal sands of these channel sequences, at the margins of extensive tongues of limonitic sand.One of the channels is examined in detail with respect to channel morphology, stratigraphy, and rock alteration and the geology and ore controls of the contained uranium deposits are described.A geochemical zonation reflected by variation in limonite, pyrite, carbon, and humic malleI' is defined across one of the deposits. A genetic model is proposed suggesting formation by a uraniferous geochemical cell which migrated down the stream gradient and concentrated uranium on its lateral margins adjacent to the channel bank.

Jan 1, 1978

By Kefton H. Teague

This paper deals with the practical application of the Dutch State Mines cyclone separator for fine-coal cleaning. The more important operating variables are discussed, and results of a number of continuous-scale tests on various fine coals with a 6-in. cyclone separator are given. Descriptions of the Cyanamid Pilot Plant and the 50 tph Cyclone Separator Plant at the Emma Washery in Holland are included.

Jan 1, 1950

By T de Wit, S Meyer

The location of seismic events in mines is traditionally calculated based on the arrival times of P- and S-waves for a given velocity model (homogeneous or heterogeneous). This technique is successful when the sources of seismic events are sudden and localised (eg episodes of fracturing in solid rock or dynamic slip along a plane of weakness) and thus the radiated seismic waves have clear arrivals. In massive mining operations such as block caves, strong seismic signals often originate from the movement of loose rocks on the perimeter of the fracture zone. These signals are easily recordable but do not contain easily identifiable direct P- and S-waves, making the estimation of location through traditional methods more complicated. This problem has been approached by using a ‘brightness’ location method that estimates the origin of seismic waves based on travel times of envelopes of seismic energy. This tool is extended to be applicable in a heterogeneous velocity environment that now accounts for the presence of a cave or other strong velocity perturbations. The suggested method is particularly important when caving occurs in low-stress environments (eg close to the surface).CITATION:Meyer, S and de Wit, T, 2016. Location of seismic events associated with caving using brightness method, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 225–236 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By J. D. Bardill

"The Stoddard mine, Cheshire County, N. H., was explored by the Bureau of Mines in 1944 as a source of the strategic fluorite. It was reported that the vein persisted in the bottom of old workings and the geology of the immediate area indicated the possibility of finding additional lenses.In its program of exploration of mineral deposits, the Bureau of Nines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts pre¬liminary examinations, performs the actual exploratory work, and prepares the final report. The Metallurgical Branch, R. G. Knickerbocker, chief, analyzes samples and performs beneficiation tests. Both these branches are under the supervision of Dr. R. S. Dean, assistant director.Special acknowledgment is expressed for the cooperation and assistance given by Robert F. Sherwood of the United Feldspar & Minerals Corp.; by McHenry Mosier, chief, College Park Division, Mining Branch, who aided in re¬vising this report; and by J. B. Zadra, chief, College Park Division, Metallurgical Branch, and others of his staff, who assisted in performing the beneficiation tests and analyzing samples. The field work was under the direction of Harry P. Hermance.The property lies on the southern boundary of the town of Westmoreland, Cheshire County, N. H., at approximately 72° 39’ west longitude, 42° 27’ north latitude, in the Keene, N. H. (G.S.) quadrangle.Good gravel roads lead from paved State Highway 63 to the property. A dirt road in fair condition suitable for truck leads to the nine.Dwight H. Smith, Putney, Vt., is the owner and has leased the property to the United Feldspar & Minerals Corp., 10 East 40th Street, New York 16, N. Y.Property titles were not investigated.The fluorite deposits of Cheshire Count', H. H., have been known for many years, being reported by Jackson, (Geology and Mineralogy of New Hampshire, by Charles T, Jackson, 1844) and by Hitchcock, in1878 (Geology of Now Hampshire, vol. 3, 1878, by Charles H. Hitchcock). A large pit on the largest or east vein was mined by Lovat Frazer from about 1908 to 1917, This operation is reported to have produced approximately 3,500 tons of fluorspar. In 1917, the American Steel & Wire Co, took over the mine end is said to have produced 3,500 tons of fluorspar before relinquishing the lease in 1923.From 1935 to 1937 the New Hampshire Fluorspar Cc. operated the Stoddard mine, working chiefly on the most westerly of the three known veins on the property, as well as doing some preliminary work on the small central vein. In 1938, the United Feldspar 6 Minerals Corp. leased the mine, and less than 100 tons of fluorspar was produced from exploration and development work, No mining has been done since that time."

Sep 1, 1946

By Haiping Sun, Samir Ganguly, Oleg Ostrovski, M. Yaser Lone

Wettability of graphite by synthetic SiO2-Al2O3-CaO-MnO slags with varied MnO content and by industrial slags was studied at 1350-1600 °C using sessile drop method under argon atmosphere. Initial contact angle was the lowest (110-115o) for the MnO-free slag. For slags with 10-40 wt% MnO, the initial contact angle was in the range 125-135o. The contact angle decreased with the contact time. The change in the contact angle with slag mass was found insignificant. The surface tension of slags obtained from the drop shape analyses was 500-800 mN/m and varied in a narrow range with temperature and MnO concentration. The reduction rate increased with increasing MnO content in the synthetic slag from 20 wt% to 40wt% and temperature. Increasing temperature also increased the rate of reduction. No correlation was observed between the reduction rate and MnO content in the synthetic slags in the range 0-20 wt% and in the industrial slags. The rate of SiO2 reduction from the molten slag was close to the rate of MnO reduction. The MnO-free slag had the largest contact area with graphite substrate. Keywords: reduction, wettability, graphite, slag, manganese, surface tension.

Jan 1, 2007

By N. Kuyucak

"Acid mine drainage (AMD) is one of the most significant environmental challenges facing the mining industry worldwide. It occurs as a result of natural oxidation of sulphide minerals contained in mining wastes at operating and closed/decommissioned mine sites. AMD may adversely impact the surface water and groundwater quality and land use due to its typical low pH, high acidity and elevated concentrations of metals and sulphate content. Once it develops at a mine, its control can be difficult and expensive. If generation of AMD cannot be prevented, it must be collected and treated. Treatment of AMD usually costs more than control of AMD and may be required for many years after mining activities have ceased. Therefore, application of appropriate control methods to the site at the early stage of the mining would be beneficial.Although prevention of AMD is the most desirable option, a cost-effective prevention method is not yet available. The most effective method of control is to minimize penetration of air and water through the waste pile using a cover, either wet (water) or dry (soil), which is placed over the waste pile. Despite their high cost, these covers cannot always completely stop the oxidation process and generation of AMD. Application of more than one option might be required.Early diagnosis of the problem, identification of appropriate prevention/control measures and implementation of these methods to the site would reduce the potential risk of AMD generation. AMD prevention/control measures broadly include use of covers, control of the source, migration of AMD, and treatment. This paper provides an overview of AMD prevention and control options applicable for developing, operating and decommissioned mines."

Jan 1, 2002

By Frederick H. Raab

The electromagnetic retransmission system is a new, automated method of locating trapped mine workers. This technique overcomes many 1 imitations inherent in electromagnetic direction finding by reducing the effects of the conducting ground to an acceptable maximum, by finding position accurately in the presence of antenna tilt, and by eliminating the need for the receiver to be located directly above the subsurface transmitter. Three transportable three-axis magnetic-dipole transmitters on the surface create a system of electronic grids in which the phases of the downlink Signals convey position information. The subsurface retransmitter modulates the uplink carrier of the existing beacon transmitter with the received downlink signal; the coal-pillar loop antenna is used for both receiving and transmitting. The uplink receiver uses a three-axis antenna and extensive digital signal processing. A small computer integrates data, estimates position, and controls system operation through VHF-FM communications. Both coal-mine and deep-mine operation are possible by selecting appropriate transmitting power and signal frequencies. This report shows such systems to be both feasible and practical.

Jan 1, 1980

By S. Panigrahi

The SO2-ammoniacal ammonium sulfate leach liquor generated by leaching of manganese nodules, after removal of minor quantities of iron and manganese, contained copper, nickel, cobalt, zinc and (NH4)2SO4. After extraction of copper from the leach liquor with LIX 84I, stripping of ammonia from the Cu-barren raffinate was carried out followed by precipitation of metal ions from the ammonia-stripped solution as sulfides. Leaching of the sulfide precipitate was carried out with H2SO4 to obtain a leach liquor containing 0.58 kg/m3 Cu, 2.67 kg/m3 Zn, 2.00 kg/m3 Co, 24.68 kg/m3 Ni and 10.0 kg/m3 (NH4)2SO4. After extraction of copper and zinc from the sulfate leach liquor with LIX 84I and D2EHPA, respectively, the solution was left with Co and Ni. Extraction of cobalt from the Cu- and Zn-free solution was carried out with 0.1 M PC88A and stripping of the cobalt-loaded organic was carried out with the cobalt-spent electrolyte (pH 1.4). Extraction of nickel from the cobalt-free solution was carried out with 90% neutral 1M NaPC88A followed by stripping of the nickel-loaded organic with 120 kg/m3 H2SO4 solution. Extraction of metal ions increased with increasing equilibrium pH and extractant concentration. The maximum separation factors, with respect to the pH and extractant concentration variation studies, were 3796.7 and 15350.0, respectively. The extracted species for the metal ions were CoA2?3HA and NiA2?5HA.

Jan 1, 2009

By James A. Mason

The State of California has instrumented numerous buildings, bridges, and dams throughout the state with earthquake recording devices. These accelerometers are strategically placed to measure the response of the structure to a specific seismic event. This comprehensive program enlightens the field of seismic engineering after each earthquake. The Office of Strong Motion Studies, California Strong Motion Instrumentation Program, a sub-branch of the Division of Mines and Geology, provides a professional service unequalled in the world. Within hours of a local earthquake, a preliminary report with the epicenter / hypocenter, structural damage, and time history records are available to all interested parties. The included partial report in the appendix, see section 5.1, is one of the reports that C.S.M.I.P. produced after the Loma Prieta Earthquake of October 17,1989. The diagram on the cover is even of interest. This is a small portion of San Francisco. The values on the diagram are the recorded maximum horizontal ground accelerations at that location in the city. For example, the acceleration at Yerba Buena Island was 0.06g. (The "g" refers to the acceleration of gravity. Thus, a 0.06g acceleration refers to the force, F=m*a, that the structure would experience. For this case, the force would be six percent, 6 % , of the mass of the structure.) Yet, directly on the other side of the Bay Bridge, at Treasure Island, the acceleration was 0.16g. Yerba Buena Island is a natural island composed of hard granular material. Whereas, Treasure Island is a man-made island of imported filled. Here one can see the absorption / transmission difference between hard material, which interact with short seismic wavelengths, and soft cohesive material, which interact with long seismic wavelengths.

Jan 1, 1993

By R. W. Heins, N. Street

An investigation was made of the Rehbinder-Kuznetsov pendulum as an instrument to aid in the study of rock drillability and of the effect of surface active agents on rock drillability. The "critical weight", i.e., the pendulum weight at greatest sensitivity, was determined for several solids and it was shown that a change in surface environment changed the maximum value of the apparent hardness but not the critical weight, and the critical weight increased with increase of hardness of the solid used. Using silver halides as the solid material, and solutions of either silver nitrate or the appropriate alkali halide, it was shown that there is a hardness maximum at the zero point of charge of the particular silver halide. INTRODUCTION The development of relative hardness measurement by the method of damped oscillations, or what has been called the pendulum sclerometer, is due largely to the Russian workers P. A. Rehbinder and V. D. Kuznetsov and their co-workers.1,2 The apparent simplicity of the method has led to its use in a number of fields, particularly those where relative hardness has to be determined on a brittle solid. As will be shown, the simplicity of the method belies its complexities. THEORY OF THE PENDULUM SCLEROMETER The operation of the pendulum is quite simple. Make a sharp point such as a diamond, hardened steel or tungsten carbide, as the fulcrum of a pendulum, with the center of gravity of the system below the point of support. The attenuation of this pendulum is a function only of air friction, provided no fragmentation, breakage or other work is performed by the point. However, when the solid surface breaks or disintegrates under the point, and the latter penetrates the solid, part of the energy of oscillation is absorbed in the work of creating new surface, and the rate of attenuation increases. In the case of brittle solids, the point of the pendulum produces fragmentary particles, whereas the point produces plastic deformation in a plastic solid; but in both cases damping occurs. This pendulum damping is a function of the hardness or strength of the solid. Whereas a pendulum oscillating on a hard material attenuates primarily by air friction, in the case of a soft material, the points penetrate the surface of the solid, producing new surface, and the pendulum damps much faster. Thus the attenuation rate is a function of the hardness or strength of a material in both plastic and brittle substances. Russian workers initially used a single support for the pendulum, but this created many problems because of oscillation of the pendulum in more than one plane. A revised version used two points, or sometimes a prism as support, successfully confining oscillation to one plane. The version using two points was constructed and used throughout this investigation, making the recording of the attenuation as a function of time relatively easy. That both points should be in contact with the solid during the damping is implied. Rehbinder (c.f. Kuznetsov2) proposed that the hardness H as measured by this method could be expressed by a quantity which is inversely proportional to the relative initial rate of attenuation of amplitude. where H = hardness parameter (arbitrary units) a, = initial amplitude da/dt = rate of attenuation of amplitude with time. In the simplest case of damping with a constant logarithmic decrement, H can be regarded as a constant for the duration of the whole damped oscillation process. That is

Jan 1, 1966

By Robert B. Bittner

Large diameter piles (2 to 3 m diameter, both driven and drilled) are being used more frequently by designers of bridge foundations. The use of these large piles allows the pile cap to be positioned off the bottom but usually still below water. Conventional cofferdams as shown in Figure 1 below are not suited to this type of pile cap. However, float-in cofferdams offer a viable alternative. This paper describes the float-in cofferdam system, its initial development for use on the Bath-Woolwich Bridge in Maine and its most recent application on the new Carquinez Bridge in California.

Jan 1, 2013

By Maurice Bottiau

It is a quite challenging objective to aim at covering in one paper the most recent evolution in piling and deep foundations technologies. This report has to be understood within the limits of the session 2b. It will therefore concentrate on the technological evolution of deep foundation techniques, addressing design issues only when directly related to execution aspects. For the same reason, it will not address the related codes, as a separate session of this conference is specifically dedicated to this topic. Monitoring and deep excavations being covered in other sessions, they will only be addressed when clearly relevant. We will try to show, from a practical viewpoint what are the main changes and the most exciting or critical issues over the last years, as they appear from the topics addressed in the literature or in the papers published in this session of the conference. As the paper mostly intends to explain trends and critical topics, it cannot be exhaustive, neither can it give the full description of the case studies. The author invites the reader to read the full papers, for a more complete description. We have divided our report in three main topics: Piling, soil improvement and treatment and retaining walls. Anchors and tie-backs will not be treated, neither tunneling.

Jan 1, 2006

By Thomas O. Glover

The mining industry of Cameroon continued to be dominated by crude petroleum. Crude petroleum production has become the most important facet of Cameroon's economic development. Oil production was estimated to be 6.3 million tons in 1983 compared with 5.2 million tons in 1982 and 4.3 million tons in 1981. Over two-thirds of its export income was attributed to crude oil. The country's only refinery, dedicated in 1981, has a production capacity of 2 million tons. Cameroon has become self- sufficient in petroleum products since commissioning the refinery. The oil sector contributed approximately 13.5% to Cameroon's gross domestic product in 1982-83. Oil production was expected to rise from 125,000 barrels per day in 1983 to 156,000 barrels per day in 1985 when output peaks. Cameroon's ultimate recoverable reserves have been calculated at 100 million tons, or 750 million barrels of oil.

Jan 1, 1985