Search Documents

By Hayes J. A

The satisfactory ventilation of an extensive coal mine is a subject which requires continual attention from all concerned.It must be remembered that a colliery contains many miles of workings, extending in all directions and throughout which noxious gases may be given off either naturally or by oxidation of the coal; fumes from explosives will be produced, dust will be gathered and carried in suspension, and water will be evaporated, producing a high humidity. Hence a considerable quantity of air in movement must be available to provide sufficient oxygen for men and horses, as well as to dilute and sweep away impurities, and maintain a tolerable degree of coolness.To maintain these conditions a modern colliery is divided up from the main ventilation shafts or adits (as the case may be) into a system of main airways, and in the working districts is further subdivided into district splits. To initiate the air movement, large centrifugal fans with a displacement capacity of up to 400,000 cu. ft. of air per minute are installed, generally in drifts off the upcast shaft, or adit, and at the return end of the ventilating circuit. These fans are thus exhausting fans and by producing a region of low density bring the heavier air at the other extremity of the circuit into movement to correct the difference in density, so far as it is not prevented by the frictional resistance of the airways. A flow of air is thus established, and it is obvious that to enable this volume of air to be as great as possible, the frictional resistance of the mine airways should be maintained at the lowest practicable figure. To this end, main airways should be as large as possible, have sides as smooth as practicable, and be straight, any necessary bends being of large radius.REQUIREMENTS OF THE VENTILATION SYSTEMThe New South Wales Coal Mines Regulation Act contains stringent provisions on requirements of the ventilation system. The main points are expressed in the following extracts:"In every mine which is in operation, unless a certificate of exemption from compliance with this rule has been granted by the Minister, whether any person employed therein shall be...

Jan 1, 1947

By Tina Maniatis

Applied Biosciences has developed a biological technology for removal of arsenic, nitrate, selenium, and other metals from mining and industrial waste waters.The ABMet® technology was implemented at a closed gold mine site in Canada for removing arsenic from tailings pond water. The system included six bioreactors that began treating water in the spring of 2004. Design criteria incorporated a maximum flow of 567 L/min (150 gallons per minute) and water temperatures ranging from 10°C to 15°C. Influent arsenic concentrations range from 0.5 mg/L to 1.5 mg/L. The ABMet® technology consistently removes arsenic to below detection limits (0.02 mg/L). Data from the full scale system will be presented, as well as regulatory requirements and site specific challenges. Keywords: Arsenic, Sulfate Reduction, Metal Sulfide Precipitate, Biological Water Treatment

Jan 1, 2005

By Enrico Tosolini

O controle da massa linear dos arames CA60 vem sendo tratado com máxima prioridade, devido ao constante esforço da indústria nacional de reduzir os custos e melhorar a eficiência de produção. O trabalho é um estudo teórico dos fatores físicos que influenciam na variação da massa linear. Para desenvolver a análise, o problema foi simplificado para reconduzi-lo a um problema linear de fácil análise e com parâmetros intuitivos para fácil aplicação dos conceitos nos problemas diários da produção.

Aug 16, 2017

By G. B. Atkinson

The Bureau of Mines investigated a method for increasing the leaching rate of bulk superalloy scrap to facilitate recycling and recovery of critical metals such as Ni, Co, and Cr. Three superalloys were investi- gated, the cast-nickel-base superalloy IN-738, the wrought-nickel-base superalloy Rene-41, and the cast-cobalt-base superalloy Mar-M-509. Superalloys melted with 20, 30, 40, and 50 pct Al metal to form inter- metallic compounds were easily crushed to a convenient particle size and reacted rapidly with acid solutions which dissolved the metals. For example, leaching 1/2-in pieces of unalloyed IN-738 with excess 6N HC1 at 95° C for 2 h dissolved about 0.5 pct, while leaching 10 g of minus 20-mesh 30 pct Al-70 pct IN-738 with excess 6N HC1 at 95° C for 2 h dis- solved 96.2 pct.

Jan 1, 1983

By Akihiko Nishiyama

Unmanned construction technology used for remote control operation of construction machines has some problems to solve compared with manned operation of construction machines, such as fatigue due to long-term operation or decreases in operational efficiency. To solve these problems, we recorded the viewpoints of operators in both manned and remote control operation and analyzed the differences. This paper reports on our discussion of improving the operability of remote control operation based on the analysis results.

Aug 1, 2013

By Henry M. Harris, John E. Kelley, Thomas D. Roberts

A penetrometer apparatus for measuring viscosity of glass at temperatures up to 1,450 ° C was developed for use in establishing the viscosity coefficients required for high- temperature forming of ceramic materials . The major advantage of the method is that it can be used with samples of almost any shape or size without the necessity of forming or measuring shapes to close dimensional tolerances . Also , it has proved accurate in the range of 106 to 109 poises , a gap between the normal limits of other methods . The device , which operates on a single penetrometer principle , was used to determine the absolute viscosity coefficient of substances in centimeter - gram- second units of poises instead of relative penetration - rate units as with other penetrometers . Penetration of the viscous sample was sensed with a linear , variable differential transformer . The output of this transformer was recorded versus time , and the penetration rate was used in calculating the viscosity coefficient . The general equation relating penetration rate and viscosity coefficient was found to be 11 = F ( ln L/a 0.72 ) 2 π UL · where is the viscosity coefficient in poises , F is the penetrator load in dynes , L is the penetration depth in centimeters, a is the penetrator radius in centimeters and U is the penetration rate in centimeters per second . The penetrometer was tested using a standard viscosity sample of sodalime - silica glass obtained from the National Bureau of Standards ( NBS ) . Values obtained at several temperatures all agreed within 10 percent with comparable data calculated from the Fulcher equation derived by NBS for this glass . Equivalent accuracy was obtained with other glasses used to evaluate the apparatus .

Jan 1, 1964

By J. Botula

In the region of the North-Bohemian Coal Basin and its environment, there, in a row of places, are found the accumulations of rocks of the sedimentary and pyro clastic origin, the preliminary composition of those shows the possibility of their being utilized for the production of ecologically sparing natural Fe- and Ti- pigments and filling substances. In many places of the regions of Chomutov and Podborany and near Bilina and also in other places, there are found raw stocks perspective for the preparation of yellow up to ochre-brown, red, brown-red and green dyes. The target of project is the verification of dispensable reserves, their mineralogical composition and chemical and physical attributes, verification of treatment ways of Fe-and Ti-pigments separation (hydrocyclones, magnetic and electrostatic separation) and their stabilization and technological painting attributes for applications in colors, coating and plastic masses, mortar mixtures etc.

Jan 1, 2014

By E. Tarshizi

Research was conducted to develop a simulation and animation model for an aggregate (sand and gravel) mine operation. This model can assist the mine engineers to investigate and consider the various options of haulage systems which are critical for the mine operation productivity. Discrete-event system simulation studies can be used for the typical haulage issues that mining engineers are often faced with: using truck fleet haulage, conveyor belts, or a combination of both. The simulation has identified some strengths and weaknesses in the current loading and hauling fleet of the mine, and has resulted in some suggestions for improving the system. The simulation includes animation of the operation. Animation is needed to enhance the benefit of any mine simulation model. By combining the visual power of animation with a mine simulation, a complete picture of the mine system is obtained and displayed. The mine is modeled and animated using GPSS/H® and PROOF Professional®, both of which have shown great applicability in discrete mining simulation projects.

Feb 23, 2014

By Beatriz Fausta Gandra

A preservação do refratário do cadinho é fator determinante para o prolongamento da vida útil de altos-fornos. Assim, o presente estudo teve por objetivo avaliar o efeito da variação da composição química do gusa (silício, manganês e enxofre) sobre o bloco de carbono do cadinho, com foco na obtenção de informações que permitiram inferir sobre a viscosidade e a tensão superficial do gusa. Isto foi realizado por meio de análises via microscopia de aquecimento e ensaios para determinar a penetração de gusa em bloco de carbono a altas temperaturas. Os resultados indicaram a tendência de elevação do ângulo de contato entre o gusa e o bloco de carbono a partir do aumento do silício e do enxofre no gusa. Por outro lado, verificou-se que o ângulo de contato reduz com o aumento do manganês no gusa. Dessa forma, o gusa contendo maiores teores de silício e enxofre penetrou de forma menos significativa no bloco de carbono, enquanto que o gusa com altos teores de manganês penetrou de forma mais intensa no bloco de carbono. Esses resultados permitem estabelecer faixas de controle da composição química do gusa, em consonância com as necessidades de preservação dos altos-fornos e de sua estabilidade operacional.

Oct 30, 2017

By Herbert J. French

ALLOY steels have become essential to industry in meeting the rigid requirements on materials imposed by our, advanced technology. In comparison with the total ingot capacity of the steel industry, the volume of alloy steels is relatively small although for many years annual alloy-ingot tonnage has, been in seven figures. However, the monetary value of the alloy-steel production is exceedingly high and the benefits derived from the products are relatively great. The trend in total ingot production since 1932 has been generally upward with only two major interruptions. That of the year 1938 was due to a decrease in general business activity whereas that of 1946 resulted largely from work stoppages. Traditionally, the tonnage of alloy-steel ingots produced was in the neighborhood of 5 to

Jan 1, 1948

By Rafael Amboss Pinto

O objetivo do SHTPN (Solution Heat Treatment after Plasma Nitriding) é a adição de nitrogênio em solução sólida na superfície, formando austenita durante o tratamento térmico de solubilização, possibilitando a obtenção de martensita de nitrogênio após o resfriamento. Foram ensaiadas amostras nas condições: de fornecimento (microestrutura ferrítica); nitretada (com camada de compostos); após SHTPN (martensita não revenida); e SHTPN seguido de quatro temperaturas de revenimento (martensita revenida). Os ensaios tribológicos foram realizados em placa contra esfera de metal duro, movimento recíproco. Os mecanismos de desgaste foram caracterizados por microscopia eletrônica de varredura (MEV) e as profundidades das pistas foram medidas em rugosímetro 3D. A condição de maior resistência ao desgaste foi a nitretada. Entretanto, a superfície desgastada destas amostras apresentou microtrincas. O comportamento tribológico da amostra revenida a 600°C foi similar ao observado para amostra no estado de fornecimento, pois apresentaram predominância do mecanismo de adesão, com grandes deformações plásticas na superfície. Todas as outras condições apresentaram menores profundidades de desgaste do que o estado de fornecimento, com mecanismos predominantes transitando de abrasão para adesão com o aumento da temperatura de revenimento. Na amostra após SHTPN, a baixa capacidade de deformação plástica da camada martensítica não revenida causou fratura do material nas laterais da pista, o que não ocorreu para as condições revenidas.

Aug 8, 2018

By Bryant Fitch

This paper will review thickening theory, from the ( ) of the practicing engineer, with particular emphasis on ( ) uncertainty or disagreement. It will attempt to outline broadly what we know and what we don't know. This should serve two purpose First, it will warn the process engineer where he might get into trouble. At least it will alert him to the risk involved in uncritically accepting any of the recommended design procedures. Second, it will identify for researchers some areas in which further work might be fruitful. Not too many years ago there would have been little to write on such a subject. We had been designing thickeners for decades, using the classic Coe and Clevenger procedure. As far as we were generally aware, they all turned out to be about the right size. And so if there was anything we didn't know, It certainly wasn't hurting us much. Today we know better. While it is true that in most cases units designed by the Coe and Clevenger procedure (1) will perform satisfactorily, we now know of cases in which they don't. And during the past few years there have been many developments and advances in basic thickening theory. So there is now a lot more room for disagreement, and a whole lot more to be uncertain about. What is "thickening" "Thickening" means different things to different people. For this paper we define it to mean sedimentation behavior characterized by line settling. Solids subside with a clear line of demarcation between settling solids and supernatant. Although the supernatant will usually be clear, in some cases it may be turbid. Line settling must entail that all particles just below the pulp-supernatant interface have the same subsidence rate, so that

Jan 1, 1971

By Onuralp Yucel, Osman Halil Celik, Hakan Morcali

In this study, some experiments were performed for the dimensional control, pre-treatment, getting salt, metallic aluminum and aluminum oxide into the solution of 15 kg aluminum black dross obtained from a private company which recycles aluminium drosses. Water leaching experiments are done for removing salts and aluminum nitride. Temperature stirring speed, solid-liquid rate are investigated while water leaching experiments. Removing of AlN is provided at 25 °C at a rate of 42.48%, at 80 °C at a rate of 86.4%. Leaching experiments performed with NaOH. NaOH concentration and time was analyzed. Efficiency of including metallic aluminum into the solution is determined to be 98% approximately. Melting (fusion) experiments were performed with NaOH at high temperatures to include aluminum oxide in the structure of the remaining after dissolving process into the solution and after dissolving the resulting structures in water, efficiency of including aluminum into the solution is determined to be 85%.

Mar 1, 2018

By H. Y. Sohn, M. Pérez-Tello, P. J. Smith, K. M. Riihilahti

A three-dimensional computer model for the Kennecott-Outokumpu flash converting process for copper matte is presented. The model incorporates the transport of momentum, heat and mass, and reaction kinetics between the gas and particles in a particle-laden turbulent gas jet. The k-E model is used to describe gas-phase turbulence in an Eulerian framework. The particlephase is treated from a Lagrangian viewpoint which is coupled to the gas phase through the source terms in the Eulerian gas-phase governing equations. Matte particles were represented as Cu2S·yFeSx. Based on experimental observation, the oxidation products were assumed to be Cu2O, CuO, Fe3O4, and SO2. A reaction mechanism involving the external mass transfer of oxygen to the particle surface and diffusion of the oxygen through the oxide layers of CuzO/Fe304 and CuO/Fe3O4 is proposed. Predictions of the mathematical model were compared with the experimental data collected in a large laboratory furnace. A reasonable agreement between the model predictions and the measurements was obtained in terms of fractional conversion of the oxidation reactions and of sulfur remaining in the reacted particles. The simulation of an industrial flash converting furnace was also performed. Higher oxidation rates, more even distribution of particles, and thus a more efficient use of the reactor volume are predicted with a burner having a distributor cone, than with a single-entry burner.

Jan 1, 1999

By L. A. Panek, A. J. Barry, John A. McCormick

"INTRODUCTION During recent years, roof bolting has become widely accepted as a systematic method of supporting both coal- and metal-mine roofs. Today, over 2 million roof bolts are installed monthly. Most of the information on bolt installation procedure reported to date (1,2,3,4,5,6) 3/ has been obtained by trial and error by individual groups or operators. To insure good roof control, experience and field tests have indicated that roof bolts should be installed immediately after the exposure of new roof, and they should be preloaded enough to minimize sag of the roof over the opening. The question of the proper initial preload for roof bolts is under study, although it is a general practice to impose an initial load on a bolt of approximately 10,000 pounds. This created a problem of measuring bolt loads at installations in underground mines, which was partly solved by using a commercial-type torque wrench; a device that permits a direct reading of the torque applied to the nut on a roof-bolt assembly from which the corresponding load can be determined by referring to specifications furnished by the manufacturers. However, considerable apprehension was expressed regarding the accuracy of this measuring procedure because of variations in the manufacture of roof-bolting materials and the degree of care exercised in making bolt installations. In the process of loading a bolt, only a small part of the effort is expended in producing strain in the bolt - the larger part of the effort is used in overcoming frictional effects in the nut-bolt-washer assembly. These frictional effects are subject to many factors, such as condition of threads, type of lubrication, if any, the finish on the nut and bearing plate, and the alinement of the bearing plate on the bolt. The object of this investigation was to determine the accuracy with which the load developed in a slotted-type roof bolt installed in a conventional manner in shale or sandstone roof rock can be determined from the torque applied to the nut.This report is the first of a series relating to basic research in roof bolting in underground mines. A future report will cover results obtained using expansion-type bolts under similar conditions. Other reports will consider the efficiency of bolt anchorages, the long period stability of bolts, and the design of safe and efficient roof-bolting systems."

May 1, 1953

By A. Oyler

The U.S. Bureau of Mines has compiled data on the major causes of fatal and nonfatal electrical accidents related to mining, and their associated costs, for the 1980-85 period. Specific electrical problem areas were identified, allowing future research to be focused on reducing the frequency of these occurrences. Recommendations for reducing the number of electrical accidents and injuries are provided. The four mining sectors for which data were gathered and compiled are (1) underground coal mines, (2) surface at underground coal mines, (3) underground metal-nonmetal mines, and (4) surface at underground metal-nonmetal mines. Nine categories of information pertaining to specific aspects of the accident are used in this report: activity engaged in when the accident occurred, source of injury, job title, mining method, location, machine, nature of injury, accident type, and part of body affected. The number of years of experience at the specific job the employee was performing when the accident occurred, time of accident, and in the case of nonfatal accidents, the total days lost per year, are also summarized.

Jan 1, 1990

By A Bax, G Wardell-Johnson, W P. Staunton, J McGrath, J J. Eksteen

Since 2001, the AMIRA P420 gold processing technology project series has been studying the recovery of gold using gravity devices, with particular emphasis on the centrifugal units, Knelson and Falcon concentrators. The work has entailed the surveying of operating gravity circuits in Australia, Africa and North and South America.This paper reviews some of the results and lessons of these studies, including common circuit operating and design factors, which limit gravity recovery; pointers towards effective modelling of gravity circuits; and the contribution of gravity to overall gold recovery.CITATION:Wardell-Johnson, G, Bax, A, Staunton, W P, McGrath, J and Eksteen, J J, 2013. A decade of gravity gold recovery, in Proceedings World Gold 2013 , pp 225-232 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By L. H. Gevantman

A program for the compilation of evaluated physical and chemical numerical properties data is being pursued at the National Bureau of Standards within the Office of Standard Reference Data. This program is being sponsored by the Department of Energy and managed by the Battelle Office of Nuclear Waste Isolation in Columbus, Ohio. The intent is to assemble a reliable body of numerical properties data concerning candidate mineralogical materials in which high-level radioactive wastes are to be buried. The ready accessibility of the data to site designers and the credibility achieved through the evaluative process are designed to help assess and compare the feasibility of each candidate material for use as a disposal site. Both generic and site-specific data are to be assembled. To date, generic rock salt properties have been assembled and published by the NBS as NBS Monograph 167. Details of the effort to produce this book are discussed.

Jan 1, 1982

By Peter N. Calder

The selection of a slope angle for an open pit in rock has often been made without the benefit of a comprehensive engineering study. This is largely due to the fact that the hardware and procedures necessary for such a study have not been available. Recently this situation has been reversed. The application of borehole television and terrestrial photogrammetric devices has made possible the accurate determination of rock joint structure, on which stability calculations can be based. Another important aspect is the evolution of practical methods of conducting in-situ rock joint strength tests.

Jan 1, 1971

By A. Yudiarto, M. Z. Mubarok

At the present paper, synthesis of magnesia from ferronickel smelting slag is discussed. The first stage was extracting magnesium from the slag by leaching in HCl solution. Magnesium extraction of 97% was obtained from the slag leaching with HCl 8 molar, solid:liquid ratio 1:40 (g/ml) and temperature 80 °C after 24 h. Solution purification was performed by adjusting solution’s pH at 95 °C with addition of MgO powder. At pH range range of 3–4, co-dissolved iron was removed as akagenite (b-FeOOH) precipitate. Dissolved nickel precipitation was detected at pH range of 4–6, while dissolved Mg and Al started to precipitate in the forms of pyroaurite (Mg6Fe2CO3(OH)16∙4H2O) and hydrotalcite (Mg6Al2CO3(OH)16∙4H2O) at pH range of 8–9. High purity of brucite (Mg(OH)2) was obtained by Mg precipitation at pH range of 11–12, under stirring speed of 300 rpm and stirring time of 4 h. Calcination of brucite at temperature of 1000 °C completely converted brucite to periclase (MgO) powder after 240 min.

Mar 1, 2017