Search Documents

By R. D. Smith

The Bureau of Mines (BOM) evaluated the technology, capital investment, and annual operating costs of emission control for further reductions of lead in ambient air at the East Helena, Montana, smelter, and the Glover, Herculaneum, and Buick smelter-refineries in Missouri. This study seeks to analyze the technology available to the domestic primary lead industry for attempting to further reduce lead emissions below 1985 levels. Through enclosure of concentrate unloading and handling areas and all lead-processing buildings, followed by venting these enclosures to the atmosphere through baghouses and the application of appropriate local controls, emissions can theoretically be reduced by a total of 2,424 pounds of lead per day from 1985 levels at the three Missouri operations. Using conventional technology, aggregated additional capital costs of $250,014,000 and annual operating costs of $18,507,800 are estimated for the four operations, resulting in a total cost of $0.063 per pound of refined lead. Continuous drossing techniques would assist in meeting OSHA standards in process areas. Continuous drossing would change capital and operating costs to $258,344,800 and $16,104,700, respectively, for a total cost of $0.062 per pound of refined lead. First quarter, 1986 open market price for refined lead was $0.184 per pound.

Jan 1, 1986

RISKGATE is an interactive online risk management system developed by the Minerals Industry Safety and Health Centre (MISHC; University of Queensland) to maximise health and safety performance in the mining industry through implementing continual improvement in management of major unwanted events. A comprehensive knowledge base has been captured for risk management of tyres, collisions, fires, isolation, strata underground, ground control open cut, explosions, explosives, manual tasks and slips/trips/falls. This will be extended to outburst, coal burst and bumps, interface displays and controls, tailings dams and inrush in 2013. RISKGATE presents substantive and leading edge controls to assist industry stakeholders in the design, management and reporting of organisational and regulatory compliance requirements. From a broader industry perspective, RISKGATE provides an environment for knowledge capture and knowledge exchange to drive innovation and best practice in the identification, assessment and management of risk. By capturing operational knowledge from industry experts, RISKGATE provides a cumulative corporate memory at a time of high personnel turnover in the coal industry. All major Australian mining companies are contributing topic experts to this broad industry initiative. In the first 24 months, nine coal mining companies nominated over 80 different experts who contributed over 400 days of individual time to the knowledge capture workshops. RISKGATE is the largest single Australian Coal Association Research Program (ACARP) occupational health and safety (OHS) initiative to date.

Aug 1, 2013

By B. Q. Xiao

In surfactant flooding, surfactants added are often a mixture of the same type of molecules with different lengths of carbon chains. The relationship between a single, pure surfactant solution and crude oil is seldom studied. Additionally, up to now, alkylbenzene sulfonates are applied widely in surfactant flooding, such as Daqing oilfield, China. A factory producing alkylbenzene sulfonates will enlarge its yield to 20 000 tons per year over there. For the purposes of widening the alkylben-zene sulfonates? application, 16 kinds of pure alkylbenzene sulfonates were synthesized through Friedel-Crafts acylation and Wolff-Kishner reduction reactions, and the compounds? molecular structures were confirmed by 1HNMR and 13CNMR spectra. The factors affecting interfacial tension (IFT), such as, surfactant type, oil composition, electrolyte concentration, and alkali concentration were considered. The synthesized pure surfactants? critical micelle concentration (CMC) and optimal salinity were measured through interfacial tension technique. According to lab experiments results, heavy alkylbenzene sulfonate (2SY) was synthesized in magnifying scale in Jinzhou Wash Chemical Plant and the coretests were conducted using it. The results showed that the homemade heavy alkylbenzene sulfonate (2SY) flooding can improve oil displacement efficiency 20% more than water flooding at surfactant?s concentration from 0.05%(wt) to 0.2 %(wt).

Jan 1, 2014

By Douglas B. Silver

Study Parameters (Status as of February 1993) Time Period: 1989 -1991 151 North American Public Metal Mining Companies Fiscal not calendar year basis 85+% of Canadian and U.S. Metal Production Au, Ag, Cu, Pb, Zn, Mo, Ni, W Results are Preliminary and Research Continues Chicken Little is Alive and Well

Jan 1, 1993

By L. A. Neumeier

The Bureau of Mines evaluated the properties and anisotropy in properties of rolled Zn-Cu and Zn-0.12 pct Ti-Cu alloys with various copper additions to 1.25 pct. The alloys were rolled cold and at various hot-rolling temperatures to reductions as high as 92 pct after breakdown rolling. The properties are extremely sensitive to various combinations of composition, rolling temperature, and rolling reduction, Zn-Cu alloys can develop good creep resistance, but they are inferior in that respect to Zn-Ti-Cu alloys. For alloys either with or without the titanium addition, cold-rolling results in recrystallization of the matrix and rejection of copper from solution, causing poor hardness, tensile, and creep properties, but high ductility. Peak tensile strengths develop when the alloys are rolled in the range 320° to 400° F, Best creep resistance for Zn-Cu alloys requires higher rolling temperatures when copper content is increased. Creep resistance is best for Zn-Ti-Cu alloys with about 0.75 to 1.0 pct CU rolled near 480° F. Some copper is soluble in the TiZn15 phase, which forms into "stringers" during rolling. The possible contributions to creep behavior of factors such as distribution of second-phase particles, grain size, and preferred orientation are discussed.

Jan 1, 1970

By D. Beneteau, D. Milne

"Advances in technology provide educators with valuable tools to enhance their teaching and efficiently deliver content to larger audiences. University educators are often encouraged to become more “research intensive” and to increase student enrollment. Faced with these pressures, there is a tendency to use technology to improve teaching efficiencies rather than to enhance existing teaching approaches. Practical learning in applied engineering courses would suffer greatly if hands-on experience is not emphasized. This paper discusses advantages and limitations of new technologies applied to learning, and methods to incorporate more hands-on experiential teaching techniques to applied mining engineering courses.RÉSUMÉ Les avancées technologiques fournissent aux éducateurs des outils intéressants pour rehausser leur enseignement et livrer efficacement de la matière à de grands auditoires. Les éducateurs universitaires sont souvent encouragés à devenir plus « axés sur la recherche » et d’augmenter l’inscription d’étudiants. Face à ces pressions, il y a une tendance à utiliser la technologie pour améliorer l’efficacité d’enseignement plutôt que de rehausser les approches existantes d’enseignement. L’apprentissage concret dans les cours d’ingénierie appliquée souffrirait grandement si l’accent n’est pas mis sur l’expérience pratique. Le présent article discute des avantages et des limitations des nouvelles technologies appliquées à l’apprentissage et des méthodes pour incorporer plus de techniques expérimentales pratiques aux cours de génie minier appliqué."

Jan 1, 2016

By George E. Cole

"It is a truism that the metals, and particularly the precious metals tend to monopolize the attention of those interested £n the mineral industry. This is a tendency to be mildly, but actively and continuously combatted if we are to have a well-rounded mineral development." There are in the province of Ontario a number of industries centred about the non-metallic minerals. Too little is heard of the part these play in our industrial life. It is with the intention of showing what the gypsum industry is doing in Ontario that this paper is written. The writer lays no claim to any originality in the discussion and merely offers some material in an endeavour to assist in bringing about that 'well-rounded mineral development' sought for Ontario. M. Y. Williams in his "The Silurian Geology and Faunas of Ontario Peninsula and Manitoulin and Adjacent Islands"1 in discussing the industries dependent on the Silurian rocks of south-western Ontario points out that "the splendidly ordered gypsum mine at Caledonia, formerly owned by the Alabastine Company of Paris, and now owned by the Ontario Gypsum Company, is a revelation to the average man, who disconnects mining entirely with this part of Ontario". This region is better known as one of the richest and most thickly settled agricultural areas in Canada.

Jan 1, 1925

By Bruce R. Lipin

Chromite, the only ore of chromium, occurs almost exclusively in mafic-ultramafic rocks and their weathering products. However, not all kinds of mafic-ultramafic rocks are favorable hosts for possible low-grade chromite deposits. For instance, chromium-bearing basalts are not favorable because they commonly contain < 0.3% Cr2O3, and chromite is almost always less than 50 um in diameter, if it is present at all. Chromite-bearing ultramafic rocks in stratifonn and alpine complexes tend to be either ore grade (> 25% Cr203) or very low grade (< 2% Cr203); intermediate rocks are scarce. In most complexes large tonnages exist only in the < 2% Cr2O3 group and the composition of the chromite is commonly unsuitable for metallurgical use. Some nickel laterite districts contain more than 108 tons of material with 2.0% to 5.5% Cr2O3, and hence, chromium could be a byproduct of nickel in some laterite districts.

Jan 1, 1982

A preliminary research and development program dated April 25, 1974, was prepared for Development Engineering, Inc. (DEI) for laboratory, field and other engineering studies on the disposal of retorted oil shale. This program was revised and published as a final document dated December 17, 1974. The document included discussions on the peculiarities of retorted shale materials to be investigated and discussions of the various laboratory and field tests which would need to be conducted to define their physical and chemical properties. The proposed research and development program was divided into eight work phases as follows: I Program Development. II Exploratory Laboratory Tests on Old U.S.B.M. Retorted Shale. III Laboratory Tests on Pilot Plant Retorted Shales. IV Laboratory Tests on Retorted Shales from the Semi-Works Plant.

Jan 1, 1976

AALL, Christian H.,(M&apos;49), Asst Res Dir Monsanto Chemical Co Anniston, Ala AALSETH, Earl P ,(J,51), Amerada Petr Corp Geological Dept Williston N Dak AAMOT, Olav Crone, (M&apos;29), Met Pacific N W Alloys, Inc , Box 6215, Hillyard P 0 Spokane 14, Wash AARING, Floyd D ,(J&apos;48), Petr Engr P 0 Box 130, Calgary, Alta Canada AARCNSON, Hubert Irving, (S&apos;47), Carnegie Inst of Tech., Pittsburgh, Pa ABADIE, Henry G ,(M&apos;43), Asst to the Sup- of Operations, Long Beach Oil Development Co ,255 So Santa Clara Ave Long Beach, Calif ABBISS, H. J., (A&apos;50), Min. Engr., Buchans Mining Co., Ltd.. Buchans, Newfoundland ABBOTT, Clarence Eugene, (M&apos;04), 901 Insurance Bldg , Raleigh, N C ABBOTT, George, (S&apos;52), Mass Inst of Tech Cambridge, Mass

Jan 1, 1952

By R. W. Hertzberg, F. D. Lemkey, J. A. Ford

The technique of unidirectional solidification has been applied to the A1-AI3Ni and A1-CuAl2 ezltectic alloy systems; the controlled microstructure of A1-A3Ni consists of parallel A13Ni whiskers emhedded in an aluminum matrix while the Al-CuAl2, system solidifies as parallel alternate lamellae of aluminm and CuAl2. Mechanical tests (tension and flexure) have shown that the particle-matrix interface bond formed during unidirectional solidification allowes for efficient load transfer from the matrix to the reinforcing phase. Strength and fracture characterstics of the alloys were studied as a function of phase orientation; the tensile strength of controlled Al-Al3Ni samples was 43,000 psi (three times greater than that of as-cast specime~s). The strength of the Al-CIA2, cutectic was studied as a function of lamellae-flexure stress-axis orientation using a microbend apparatus. A twofold increase in outer fiber stress was observed as the lamellae were rotated from a position of no reinforcing (perpendicular to the stress axis) to one of maximum reinforcing (parallel to the stress axis), The brittle reinforcing constituent in each alloy (A13Ni and CuAl2) was observed to he the nucleating phase for fracture. It is to be concluded from this investigation that unidirectionally solidified eutectic alloys have a potential use as reinforcing coniposite) materials. In a recent review article, Chadwick1 has described the work of many investigators in the area of controlled solidification of binary eutectic alloys. Thus far, more than twenty eutectic alloys have been unidirectionally solidified to produce structures consisting of two phases in the form of alternating lamellae or as whiskers embedded within a continuous matrix; in either case, the phases are aligned parallel to the growth direction. In particular, Kraft and Albright2 have shown that the Al-CuA1, eutectic alloy exhibits a lamellar microstruc- ture as a result of unidirectional solidification while Lemkey, Hertzberg, and Ford3 have studied the A13Ni whisker-aluminum matrix morphology in the A1-A13Ni system. Whether these alloys could exhibit reinforcing behavior would have to depend upon the strength and volume fraction of the reinforcing phase (AI3Ni and CuA12) and the nature of the bond between the reinforcing phase and the matrix. Hertzberg and Kraft4 have shown that the interface bond between chromium whiskers and a copper matrix in unidirectionally solidified Cu-Cr is particularly good while Lemkey and Kraft5 have reported chromium-whisker tensile strengths in excess of 1,000,000 psi. However, with the chromium volume fraction being less than 2 pct, no reinforcing behavior was displayed by the Cu-Cr alloy.6 In view of the encouraging results concerning the good interfacial bond and high strength of the reinforcing phase in the Cu-Cr system and preliminary mechanical test data reported by Lemkey et al.3 for the A1-A13Ni system, the A1-CuA1, and A1-A13Ni eutectic alloys containing 50 and 10 vol pct, respectively, of the reinforcing phase give promise of possessing mechanical reinforcing behavior. Based on this premise, the objective of the investigation was to study the strength and fracture behavior exhibited by these anisotropic microstructures. EXPERIMENTAL PROCEDURE Controlled Solidification Procedure. An extensive description of the technique of unidirectional solidification has been presented elsewhere.&apos; However, the pertinent details for each eutectic system studied are discussed below. Al-A13Ni System. Several master heats of this alloy were prepared by vacuum-induction melting in an A12O3crucible and casting in SiO2 mold or by induction melting in alumina crucibles under argon. The initial heats were prepared from 99.99 pct A1 and 99.99+ pct Ni, while later heats used 99.999+ pct A1 and 99.99+ pct Ni. Specimens of these master heats were unidirectionally solidified using induction and resistance heating sources and argon atmospheres at growth rates from 1.1 to 28.7 cm per hr. The thermal gradients in the liquid were controlled in the range of 26" to 36°C per cm for these runs. Al-CuA12 System. The master heat and controlled

Jan 1, 1965

In order to achieve optimum results for money spent in construction of new projects there is a need for mining developers to pay greater attention to cost control. Control is achieved by establishing a frame of reference, a method of checking and a means of remedial action. The frame of reference is a well coded set of budget estimates which graduate into definitive estimates as design is completed, backed up by drawings, specifications and bills of quantities. The method of checking is provided by cost engineering and quantity surveying input, at both feasibility study and design and documentation stages. Remedial action follows if the checking process reveals a need. In large complex projects where construction completion time is often of prime importance, control of costs can sometimes be relegated to second place. To avoid this it may be necessary to include specialists in cost control in project management teams. Quantity surveyors are trained specifically in construction economics and can provide develop- ers and project engineers with valuable support at all stages of construction.

Jan 1, 1983

By C. Samuelsson, G. Carlsson

Characterization of dust from Boliden Mineral AB’s copper-plant in Sweden was carried out using chemical analysis, X-ray diffraction analysis, energy dispersive analysis and wave length analysis using electron microprobe equipment. Dust from four different locations was characterized: the electrostatic precipitator (ESP) after the roasting furnace; the ESP after the copper smelting furnace; from the copper converter ventilation bag house filter; and from the bag house filter collecting dust from the settling furnace and tap gas ventilation. The results showed that the dust is composed of small solid and/or liquid particles from the furnace reactor which have been transported with the process gas to the dust collecting devices. This portion of the dust is mechanically formed. It also contains compounds that have been vaporized in the process and then condensed from the process gas at lower temperature, chemically formed dust. The proportion of mechanical and chemical dust varies with the process generating the dust.

Jan 1, 2001

By E. E. AGGER, Arthur Notman

THE proposal has been made in a bill introduced into Congress at the last session by Representative Jones of Michigan that an import duty of 6 c. per lb. shall be placed on copper. This action is urged after eighty years of prosperity for the industry in this country; during most of which copper has been on the free list, and during all of which a tariff would have been without real effect. To comprehend the general situation upon which this action would be imposed, we must refer to the past history of the industry and its trends at the present time. The following table supplies us with a picture of the physical growth of the industry in this country and its relation to that of the world as a whole down to Jan. 1, 1921:

Jan 1, 1925

By J. F. Wolff

CARL ZAPFFE, Brainerd, Minn. (communication to the Secretary*).¬Unless one has actually directed explorations for iron ore, it is doubtful whether the importance of Mr. Wolff&apos;s paper, the value of the information contained, and the large amount of detail work involved in what is set forth can be fully appreciated. It is indeed rare to get such a com-

Jan 3, 1917

By Rudolf E. Greuer, Linneas W. Laage, Xinton Chang

All output is saved in the file MFIRE OUT m the di¬rectory and on the disk containing the program The file can be inspected with a text processor and sent to a print¬er, if needed CONTENTS OF OUTPUT FILE The comment lines, reference temperature, air densi¬ty, a table of the units of measure for the results, and the average values are shown at the beginning of MFIRE OUT All input data will be shown in the output file if LOUT on Control line number 1 is _<-1 For each contamination source, a new branch will automatically be setup The new airway and junction ID numbers will not interfere with the original numbering scheme of the data file Next are the results of the selected simulation(s) in the following order network balancing, network balancing considering temperatures, transient-state modeling, and altered equilibrium due to fire and distribution of the contaminants. Depending upon the contents of the data file, and the simulation selected, attention, warning, and error message will be shown at locations where calculations resulted in unusual conditions

Jan 1, 1990

"Located in Madison River Canyon, about 14 miles by road from Norris, Mont. Built in 1907 by Madison River Power Co.DAM: Rock filled wooden crib structure, 183 ft. long, 34 ft. high or 44 ft. to top of flashboards.SPILLWAY: 140 ft. long, equipped with flashboards 10 ft. high.PIPE: One 10-foot and one 12-foot wood-stave pipe, 7,515 feet long.PRESSURE: One pressure chamber, 32 ft. high, 30 ft. wide and 81 ft.CHAMBER: long, built of concrete.PENSTOCKS: 4 9-foot steel penstocks about 200 ft. long, one for each wheel.WATER WHEELS: 4 double horizontal, center discharge, Sampson special 44-inch turbines, 3,600 h-p., at 100 ft. head. Speed 300 r. p. m„ direct connected to generators.GENERATORS: 4 G. E., W. C., 2,250 k-w., 4,000 volts, 300 r. p. m., 3 phase, 60 cycles, alternators, with exciters mounted on same shaft.TRANSFORMERS: 12 G. E., W. C., 900 k-w., 60 cycles. High tension voltage 23,100, 34,650, 46,200; low tension voltage 4,000, 3,800, 3,600. Now operating at 46,200, delta connected. They can be connected Y for 40,000, 60,000 or 80,000.OPERATION: This is the principal plant of the whole system and carries most of the load."

Jan 1, 1913

By K. M. Kim

An analysis was conducted to determine the effects of blasting on slope stability and downstream comminution processes. To investigate these effects, the extent of blast-induced rock damage and the magnitude of induced stress were examined. This analysis showed that damage may extend up to 500 m (1 MPa, tensile strength) into the rock mass, a distance that is sufficient to have an impact on the pitscale slope over the long term. In addition, the damage zone was calculated using the assumption that compressive waves are the primary agent in microfracturing during blast fragmentation. The calculated damage zone — up to 2.2 m (43 MPa, rock mass compressive strength) — indicates that microfracturing can occur throughout 20-50% of the entire rock mass in the blasting area, depending on the blast geometry, burden and spacing. Finally, an economic analysis was conducted by comparing two assumed blasts in a copper mine. The change in energy required for crushing and grinding was demonstrated using Bond’s law after increasing the blast energy from 180 kcal/t to 350 kcal/t. A total cost saving of 13.3% ($9.4M) was achieved with the increase. However, the benefits of blast-induced microfracturing must be balanced against the potential impacts to slope stability to ensure safe conditions, a top priority in mining operations.

Jan 1, 2014

By Joseph Hamuyuni, Fiseha Tesfaye, Daniel Lindberg

E-waste management through traditional methods such as disposing in landfills, burning in incinerators or exporting abroad for disposal are no longer options due to the strict environmental regulations. Fortunately, the presence of valuable metals in the e-waste and increasing demand for the metals as well as complexities of the currently available primary raw materials make recycling an attractive and viable option both environmentally and economically. Moreover, it is efficient in terms of resource management by closing the loop of metals. Consequently, urban mining such as the recovery of precious metals from e-waste streams through sustainable recycling processes have emerged. The sustainable recycling practices address the scarcity of primary resources and reduce consumption of energy for metals production while managing environmental issues related to hazardous materials from the e-waste streams. In this paper, valuable metals recoveries from e-waste streams through pyrometallurgical and hydrometallurgical processes are critically reviewed. And, innovative ideas for different steps of the thermochemical processes in the valuable metals and energy recovery from the e-waste streams are discussed.

Mar 1, 2017

The traditional technological flow sheets for processing of ferrous quartzite (magnetite ores) al-low production of the iron concentrates with Fe content of 65%~68 % and recovery level about 55 %. The losses of iron with the tails of wet magnetic separation are related to hematite and quartz-magnetite particles, which are not extracted under low magnetic field employed. This work presents the results of the application of reverse cationic flotation for production of hematite concentrates with weak silica content from the tailings of wet magnetic separation of mag-netite. Fine particle size, complex mineralogy and presence of locked particles determine the impos-sibility of direct production of hematite concentrate by flotation or magnetic separation. The gravity concentration allows obtaining of iron concentrate from the well-prepared feed (size fraction -53+20 µm) but with very low recovery. Thus, hematite concentrates with weak silica content and satisfactory iron recovery were obtained by reverse cationic flotation, when it was fed with iron pre-concentrate produced by high gradient magnetic separation. The best flotation results were obtained by the use of formulations based on amines of different molecular structure that modulate the structure of adsorption layer, and favour a shifting of hydro-philic-hydrophobic balance on the surface of silicates with adsorbed starch and their preferential transfer into the froth product.

Jan 1, 2014