Search Documents

By R. K. Sinha, B. S. Choudhary, Desh Deepak, A. K. Mishra, Hemant Agrawal, Shankar Kumar

Despite several methods (empirical, statistical and machine-learning tools) to calculate blast-induced ground vibration, it is not easy to predict and simulate blast vibration precisely under varying blasting loads and strata conditions due to complications in the blasting procedure. In this study, field blast data were simulated in Ansys software using explicit dynamics, and ground vibrations for 20 single-hole blasts were monitored. The densities of emulsion explosives were in the range of 0.9 to 1.15 g/cm3. In the laboratory, rock properties were determined from rock samples collected from the mine site before blasting. The in-hole velocity of detonation (VoD) and density of the emulsion explosive were also determined and used in numerical analysis to know the ground vibrations at specific points. The results of ground vibrations predicted by the model were validated using field data.

By C. O. Hawk

Distillable oils derived from coal were desulfurized and hydrogenated at 2,500 psig in a two-step vapor-phase catalytic operation to give a product rich in saturated cyclic hydrocarbons. The first step was mainly a desulfurization at 400 C, the second a saturation at 300 C. One of the oils used as feed stock was from low-temperature carbonization of a bituminous coal, the other was from the liquid-phase hydrogenation of coal in the Bureau's pilot plant. The product from the saturation step was distilled to remove the light ends and high-boiling residue and to recover a fraction having acceptable properties with respect to heating value, density, freezing point, viscosity, and boiling range according to specifications suggested by the Air Force for ultra-high-speed aircraft fuel. Quantities of the fuel fraction available were too small for the thermal stability test approved by the Air Force. The experiments, performed on laboratory scale, comprised mostly a study of the effect of varying the oil feed rate (at constant oil-to-hydrogen ratio) on the yield of the desired fuel fraction. The yield of the fuel fraction made from low-temperature carbonization oil was a little more than 1 percent of the weight of coal carbonized; that from coal-hydrogenation oil was about 12 percent of the weight of coal hydrogenated. A few attempts to do both desulfurization and saturation in one operation with sulfur resistant catalysts, developed for vapor-phase hydrogenation or hydroforming, were unsuccessful. By leaving the low-boiling ends in both feed stocks to desulfurization, another product was obtained: a low-sulfur aromatic cut boiling below 200 C. This material would be suitable as a solvent or a chemical raw material.

Jan 1, 1965

By Peter A. Cain, John C. Folinsbee

"A 4-ft.-diameter shaft has been drilled to a depth of 2,790 ft. in strong, hard, basic Precambrian rocks at Lynn Lake Manitoba. This was done on the property of Sherritt Gordon Mines Limited for the purpose of ventilating and developing the ""N"" orebody, which is located approximately 4,000 ft. south of the Farley shaft.The drilling was done under contract by two drilling companies. Peter Bawden Drilling (1964) Limited drilled the initial 12:1,4-in. pilot hole to a depth of 3,000 ft. Shaft Drillers Limited of Canada then reamed the hole to 4 ft. in diameter to a depth of 2,790 ft. At this point, the reaming was stopped because of the difficulty in passing a change in direction in the line of the pilot hole. The hole was completed by driving a raise 200 ft. from the 3000 level to the bottom of the 4-ft. hole using an Alimak raise climber.Cuttings from the reaming operation were directed into the 12:1,4-in. pilot hole, where they fell to the 3000 level and were removed by a mucking machine and standard mine development cars.The elapsed time from the start of the pilot hole to the completion of the reaming operation was ten months, with an average advance of 279ft. per month. There was a two-month delay between the completion of the pilot hole and the start of the reaming operation.The 12:1,4-in. hole was drilled in an elapsed time of 45 days from the time of setting up the rig. The average advance per day was 66.8 ft.The reaming operation was done in an elapsed time of 194 days. A one-month delay required to repair damaged equipment left 163 days for the drilling and setting-up operation, for an advance per day of 17.1 ft."

Jan 1, 1966

By Nayara Ferreira Nunes

O presente trabalho tem como objetivo promover, através da técnica de elipsometria, a caracterização de propriedades ópticas e dielétricas do nióbio metálico e, além disto, medir a espessura dos filmes finos de óxido de nióbio formados. Devido a grande variedade de aplicações em importantes setores, o nióbio se tornou um elemento de grande importância para o desenvolvimento tecnológico em áreas estratégicas e o Brasil destaca-se neste contexto por deter as maiores reservas mundiais. Logo, conhecer o máximo de informações sobre este material é de grande importância para direcionar estudos às aplicações tecnológicas a fim de se agregar valor ao nióbio e seus compostos. Após a realização das medidas de parâmetros elipsométricos, e modelagem apropriadas, foram geradas satisfatoriamente as propriedades ópticas e dielétricas do material. Sendo também medida a espessura do óxido formado de forma natural sobre o substrato de nióbio metálico.

Aug 17, 2017

By Thomas L. Vandergrift

This U. S. Bureau of Mines (USBM) report evaluates three stress-transfer-modification concepts for their potential in reducing longwall gate road stresses and closures. In each of the three concepts - packwalling, gob infilling, and entry filling -support structures are constructed on the headgate side of the panel parallel with or inby the face line. When the headgate becomes the tailgate of the adjacent panel, these structures are in place to accept stresses transferred from the mined-out panel. Using the USBM nonlinear boundary-element program MULSIM/NL, baseline models of typical longwall stress transfer behavior were developed for both intermediate depth and deep mining conditions. These models were verified by comparing model results with field measurements and observations. The stress-transfer-modification concepts were then incorporated into the deep baseline model to quantify the effects of each concept on tailgate closure. Modeling results indicated that entry filling is the most effective concept in reducing tailgate escapeway closure. Using only 18 m3 of a weak fill per meter of face advance (7.3 yd3 per ft of face advance), tailgate escapeway closure was reduced by 33%. By improving the quality of the fill, similar results were achieved using 50% less volume.

Jan 1, 2010

By Tracey Bodnarchuk, Philipp Mirzoev

Sulfate balance control is a common problem for zinc plants. Roast-leach-electrowin plants are mostly concerned with the over-generation of sulfates while for the HudBay direct leach plant both extremes are possible including potential necessity to buy sulfuric acid to replenish a sulfate-depleted circuit, which makes the problem doubly important. Quantitative methods were applied at the HudBay plant to analyze sulfate generation/depletion based on a local sulfur balance and sulfate extraction calculation in the leach circuit, using a Pb-tie method. Main factors were established influencing sulfate generation/depletion, including the critical role of Pb and pyrite. Regression analysis proved to be effective and allowed the quantitative prediction of Pb concentrations necessary to reach the equilibrium for the sulfate balance. This in turn provided a firm basis for a sulfate-control strategy realized through concentrate blend correction, which allowed the plant to fine-tune sulfate generation/depletion effectively reducing economic consequences of excessive/deficient sulfate generation.

Jan 1, 2015

By Gordon W. Hines

This paper, dealing with network planning in an industrial complex, discusses the type and size of project that can be handled on a manual basis. After a review of the fundamentals of network planning, and specifically of the Critical Path Method, the author analyses several different types of projects, each with its own characteristics. Some can be handled in conjunction with a computer, but others can be dealt with equally well without one. Among the projects discussed are a blast furnace reline, the installation of a billet mill flying shear, and routine maintenance-type operations.

Jan 1, 1967

By C. Garcia, J. J. Opazo, A. Potulsha, T. Comi

"Sierra Gorda SCM is a joint venture partnership of KGHM International (owned by KGHM SA, Poland), Sumitomo Metal Mining and Sumitomo Corp. (Japan) operating in northern Chile. The Sierra Gorda openpit mine and coppermolybdenum processing plant will become one of the largest mines in the world. The need for optimum production efficiency and sustainability has driven the creation of the most modern, wellinstrumented mine in Chile. This article contains a general review of the project including geology and history.This was a fast-track project going from greenfield site acquisition to mill startup in 10 years. Highly experienced and motivated engineers and technical staff have overcome many significant challenges resulting in a rapid ramp-up of production capacity. A potential expansion to double the production rate in the fourth year of operation has also been intensely studied.The Sierra Gorda property is located in the Atacama Desert of northern Chile, in the District of Sierra Gorda, Region II of Antofagasta, Chile (Fig. 1). There is almost no precipitation in this area. The mine site is generally flat with some rolling hills. The project is located about 5 km (3 miles) from the village of Sierra Gorda at an elevation of approximately 1,700 m (5,600 ft) above mean sea level. The village is near a highway and railway line. The city of Calama, home of the famous Chuquicamata Mine, is located about 60 km (37 miles) northeast of Sierra Gorda. In addition, the SG mine is in the midst of numerous other mines including Spence, Esperanza, Mantos Blancos, El Tesoro, Lomas Bayas, Gabriela Mistral, El Abra, Radomiro Tomic and Escondida, to name a few.The primary organizational value at Sierra Gorda is "Zero Harm." This includes employees, contractors, the environment, the community, plant facilities and mine equipment. A cornerstone of this program is called 5X5S (five by five S), which combines the lean principles of 5S with the safety model of taking five steps back and thinking about the task at hand for five seconds, five minutes, the time it takes to assess and manage the risk. "People caring about people" promotes proactive engagement in the safety of coworkers and others at work and at home."

Jan 1, 2014

By Hugo Montalvão Gontijo

Sistemas de controle avançado são utilizados em diversas etapas do processo de produção de pelotas de minério de ferro, tais como moagem, pelotamento e forno de endurecimento. O trabalho visa demonstrar as etapas para implementação de um sistema de controle avançado Metso OCS-4D© em um forno de endurecimento do tipo Straight Grate visando padronizar a operação, aumentar a produção, reduzir o gasto energético e reduzir a variabilidade da qualidade das pelotas queimadas.

Aug 17, 2017

By Eduardo Cabral

A introdução da tecnologia intensiva de mistura nas plantas de sinterização de minério de ferro tem sido vital nos últimos 20 anos, dado o fato do progressivo afinamento do minério e a necessidade de manter ou até diminuir os custos operacionais das sinterizações. As características intrínsecas da mistura intensiva facilitam a incorporação de finos cada vez mais presentes nas formulações promovendo sua aglomeração de forma eficiente, sem perda de produtividade e com economia de coque, água e energia por tonelada produzida.

Aug 17, 2017

The performance of the Australian Mining Industry over the past 10 years using key indicators of production, revenue, aftertax return investment, together with key cost elements, market changes and ore reserves is briefly reviewed. The elements of competitiveness are discussed forthe industry and the effects of Government charges and policies relating to existing operations are outlined. There is a demonstrated need for improvements in competitiveness in direct and indirect costs and for improved access to resources for the mining industry to continue to grow and add to Australia's economic growth.

Jan 1, 1987

By William Priestley

The author has shown, by .practical experiments, how the rate of cooling steel in the mold governs ingotism, segregation, the formation of dendrites, and the distribution of intergranular material; and the resulting effect these conditions have on the physical qualities of the steel before annealing, after annealing, and after forging. The paper also describes how the structure of steel is affected by the design of the mold and the method of pouring. It is shown that the various constituents of carbon steel segregate differently under different rates of cooling. For the classes of steel covered in this paper, it is concluded that the best physical structure and the most uniform chemical composition is obtained by pouring the steel at a low temperature and solidifying as rapidly as possible in the mold. MUCH time has been devoted, by metallurgists, to the study of steel after solidification and remarkable strides have been made in the heat treatment of steel, but less knowledge is available of the thermophysical, activity of the constituents of steel prior to solidification in the mold. It is known that certain elements added to steel produce marked changes in physical properties, also that other elements added to steel produce similar changes, but we have only meager knowledge as to how these elements combine in steel under different conditions of solidification. It is not sufficient to know, from chemical analysis, that a certain element is present in steel. We should know how this element is in combination with the other elements and whether the combination is such as will give the greatest physical properties. Certain elements go into solid solution with the iron, while others segregate to the grain boundaries and combine with the impurities collected there. Until it is known where an alloy produces the most beneficial effect and a means, is determined for controlling its physical location by altering solidification conditions, or otherwise, we will not obtain the maximum value from our alloys.

Jan 2, 1924

By Wei-Tong Du, Yu Wang, Peng-cheng Li, Shu-Chao Wang

CaCO3 thermal decomposition produces CO2 and CaO, and CO2 can be used as a weak oxidant in vanadium extraction. CaO will also affect the vanadium extraction process. This experiment, taking self-blowing and temperature acquisition experiment system, through adding different quality CaCO3, studies the molten iron in the oxidation behavior of C, V and P and its impact, and analysis of CaCO3 decomposition of the heating effect of the molten pool. The result indicates that adding CaCO3 in the vanadium extraction process had no obvious effect on the oxidation of carbon, but partly increased vanadium oxidation which reached more than 90%. Increased CaCO3 additions also increased cooling the molten pool, with a maximum decrease in temperature of 20 K. In addition, the oxidation of P also increased, reaching 40%. The research has proved that CaCO3 can serve to oxidize V and P is effective in vanadium extraction.

Mar 1, 2017

By Antônio Carlos Simões de Santana Filho

Entre os anos de 2012 e 2014 a CSN adotou uma série de ações para ajustar o balanço hídrico da Usina Presidente Vargas (UPV), localizada na cidade de Volta Redonda no estado do Rio de Janeiro. Tais ações possuíam o objetivo de alcançar um fluxo hídrico mais ajustado e equilibrado em relação aos seus processos produtivos, consequentemente favorecendo na identificação de novas oportunidades de redução de captação de água do rio Paraíba do Sul e principalmente na melhor quantificação no consumo de água nos processos produtivos da companhia. A quantificação detalhada, atualizada e mais precisa do balanço hídrico da empresa favoreceu uma série de ganhos operacionais, possibilitando uma comparação mais assertiva com outras empresas do ramo siderúrgico, além de alavancar diversos indicadores ambientais da CSN.

Aug 17, 2017

By Krishna Parameswaran

"This paper discusses energy use and conservation in the primary copper industry and illustrates eco-efficiency considerations, using select examples of practices at ASARCO LLC, an integrated primary copper producer and others in the industry that promote eco-efficiency. The World Council for Sustainable Business Development first publicized the concept of eco-efficiency at the Rio Earth Summit in 1992. Eco-efficiency is a management concept linking environmental and economic performance and is aimed at generating added value for a business through, among other things, increased resource and energy conservation and reduced environmental impacts throughout the life cycle of the product or service. This concept differs from sustainable development in that focus is only on economic and environmental factors and does not include social considerations. In the metal mining and processing context, this added value can be realized by implementing practices that promote conservation of water and mineral resources, conservation of energy, minimization of waste, reduced emissions and effluents and increased recycling. The examples from the primary copper industry used to illustrate eco-efficiency considerations include: water and energy conservation in mineral processing, adoption of flash and bath smelting processes, emission reduction and process improvement associated with fire-refining, implementation of green chemistry in electrorefining, promoting product stewardship initiatives and fostering renewable energy project on disturbed mined lands.INTRODUCTION ASARCO LLC (Asarco) was organized in 1899 as the American Smelting And Refining Company. Originally a consolidation of several lead-silver smelting companies, it evolved over the years into an integrated producer of primary non-ferrous metals, including copper, lead and zinc and associated co-products. Grupo México, S.A.B. de C.V acquired Asarco in 1999. Today, Asarco is a vertically integrated producer of primary refined copper and associated co-products such as gold, silver, molybdenum, selenium and tellurium. Asarco operates three open-pit mines and mills, two leach, solvent extraction-electrowinning (SX-EW) plants and a copper smelter in Arizona and a copper refinery in Texas."

Jan 1, 2017

By J. Grumer

The Bureau of Mines, under the sponsorship of the Space Nuclear Propulsion Office, conducted a laboratory-scale hydrogen safety study which determined several combustion characteristics of hydrogen diffusion flames. Experiments show that ambient air may enter the top of a hydrogen flare stack when the hydrogen flow is low. A new concept, supported by photographic evidence, predicts that diffusion flames burning in air on a wide, upright pipe (stack) and fed with slow, upward flows of buoyant gas will induce a downward flow of air along the walls of the pipe that can support combustion within the pipe. Predicted flamedip limits agree roughly with experimental values determined on 6-, 12-, and 18-inch-diameter stacks and increase with increasing stack diameter. Measurements were made of the limiting flow at which a hydrogen diffusion flame blows out in still air. By means of an empirical application of the critical boundary 8 velocity gradient concept, these data lead to a blowout limit of about 10 reciprocal seconds for a hydrogen diffusion flame. Burning rates of large hydrogen diffusion flames ranging from about 0.03 to 1 ft/sec were used to predict approximate flame heights on flare stacks. Temperatures of larger hydrogen diffusion flames up to about 3,600° F were observed, but the most representative value appears to be about 2,600° F. It was found that crosswinds do not strip significant amounts of unburned hydrogen from its diffusion flame and that water-cooled flare stacks are not likely to be damaged when flame is blown back into them by opposing winds.

Jan 1, 1970

By N. A. Sareyed-Dim

Nickel ores may be classified into two major categories : sulphide ores, and oxidized lateritic ores, these latter containing nearly 80% of the known reserves of the metal (1). Two types of lateritic ores are recognized; ores high in iron but low in magnesia and silica are known as "limonitic", while ores low in iron but containing high percentages of magnesia and silica are called "silicate" (see Table I). Sulphide ores can be beneficiated readily by conventional ore dressing techniques and the technology for nickel recovery from such ores has been well tested in a number of commercial processes (1-4). Unfortunately, no economically viable process for the concentration of nickel from low-grade deposits has yet been developed, and so only the high grade ores are able to be worked profitably. Silicate ores have been treated pyrometallurgically for the production of ferronickel (2) (3) (5); limonitic ores have been processed hydrometallurgically to produce nickel metal (2) (3) (6) (7).

Jan 1, 1975

By D. J. Wesolowski, D. A. Palmer, P. Bénézeth, S. Hilic

The equilibrium solubilities of gibbsite, Al(OH)3, and boehmite, A1OOH, have been extensively studied in our laboratory from 30 to 90°C, and 100 to 300°C, respectively, to ionic strengths of 5 mol.kg-1 (NaC1) over a wide range of pH. The resulting solubility constants have been treated with consistent empirical models that incorporate appropriate experimental data taken from the literature. These studies were initiated in part to understand and quantify scale formation in geothermal fields as a result of fluid re-injection from electric power generating plants. Most of the experimental results were obtained through application of a unique potentiometric method that allows for rapid, precise measurement of the in situ pH and allows the approach to equilibrium to be monitored from under- and super-saturation. The experimental program was extended to deal with more basic solutions (e.g., five molal NaOH), in which the dissolution of boehmite was measured for application to the refining of bauxite by the Bayer process. More recent results in strong caustic solutions at temperatures below 90°C were obtained to investigate the dissolution of aluminum-containing sludge from holding tanks at the Savannah River waste reprocessing site. In this case the solubility enhancing effects (kinetic and equilibrium) of triethanolamine were also established and quantified. Finally, potentiometric solubility experiments were conducted (50°C in 0.l mol-kg-1, NaCl) on aluminum alloy sheets to identify mainly the nature of the aluminum oxide/hydroxide surface layer formed under these conditions.

Jan 1, 2004

By M. J. McPherson, R. Venkataramani

R. Venkataramani (Assistant Professor of Mining Engineering, Dept. of Mining, The Pennsylvania State University, University Park, Pa.)-Y. J. Wang and L. W. Saperstein are to be congratulated for their paper on the computer solution of ventilation problems. The limitations on the problem size to be solved by the program (Appendix II) has been outlined in the paper. I would like to add the following additional limitations of this computer program: The dimensions of the variable J1and J2 should be changed to J, (550) and J2 (550) to handle problems containing more than 400 branches, and up to 550 branches. If there are a large number of branches common to the various meshes, another limitation on the problem size will be the dimension of the variable NA. While a higher-order polynomial fitting for the fan characteristic data points is more rigorous, a quadratic relation, if linear interpolation between the points is inadequate, will result in saving computing time without much loss of accuracy. Of course, this can be handled by minor modifications to the existing polynomial fitting routine in the program. M. J. McPherson (Dept. of Mining Engineering, University of Nottingham, Nottingham, England)-The

Jan 1, 1972

By Andreas Munko

A Outotec está desenvolvendo em escala piloto o queimador de baixa emissão de NOx desde 2012, resultados expressivos foram atingidos (o pedido de Patente já foi depositado). Em 2014 utilizando simulações CFD, os resultados atingidos em escala piloto foram reproduzidos com boa aderência e os resultados em escala industrial se mostram com os mesmos comportamentos em tendências dos resultados da escala piloto, se mostrando promissores também. O presente trabalho apresenta os passos de desenvolvimento, os promissores resultados e o próximo passo deste desenvolvimento é realizar um teste em escala industrial com o queimador desenvolvido.

Aug 17, 2017