Search Documents

By Danny Hagood

The drilling of horizontal boreholes as a means of degasification in advance of mining has been tried at Jim Walter Resources, Inc., No. 4 Mine. In a joint venture with the U.S. Bureau of Mines, a series of horizontal drainage boreholes have been drilled in the panels of an advancing continuous miner section with impressive results. The combined methane gas production rate has ranged from 205,000 to 680,000 cfd (cubic feet per day} with individual "in-seam" horizontal holes producing up to 332,000 cfd. The methane liberation from the ribs for the entire panel length has decreased from an average of 8.75 cfm (cubic feet per minute) per 100 feet of entry to 4.05 cfm per 100 feet, a 54 per cent reduction. The actual gas concentration as measure at the surface discharge point normally ranges from 85 per cent to 95 per cent methane. As a consequence of the significant reduction in methane liberation rates from the panels of the section, a 50 per cent increase in productivity from the section has been realized.

Jan 1, 1983

By R. Rodgers

The Pinto Valley concentrator of BHP Copper Inc. restarted its sulfide mining operations in September 2007 to produce copper and molybdenum concentrates. During the plant production ramp up, the copper/molybdenum circuit quickly reached the copper grade and recovery targets, but the production and quality of the molybdenum concentrate continued to be a challenge. Even though several improvements in the molybdenum circuit were completed, the final molybdenum concentrate did not meet contractual specifications. After reviewing several options to improve grade and reduce contaminants, the installation of three flotation columns were chosen. The column design and construction were done using in-house craftsmen and engineers. Ten days after commissioning, the columns successfully reached a steady operation and began producing molybdenum concentrate to the required specifications, that is, high molybdenum tenors and low copper and iron content. The Pinto Valley operations, are comprised of the Pinto Valley concentrator, the Pinto Valley dump leaching and a solvent extraction/electrowinning (SX/EW) plant. The concentrator operated from 1972 to 1998 when mining and milling operations were curtailed for economic reasons. The SX/EW plant continued operations for copper cathode production. After a cessation of mining operations of almost 10 years, Pinto Valley operations began a restart project in January 2007, to bring the mine and the concentrator back into production. Copper concentrate production started in October 2007 after refurbishing and upgrading the facilities with a new DCS system and filter plant. The daily targets of the concentrator were to treat 56.7 kt (62,500 st) of ore, produce 762 t (840 st) of copper concentrate containing 27.5 percent copper at recoveries of 86 percent and produce 2.2 t (2.5 st) of molybdenum concentrate containing more than 80 percent MoS2.

Jan 1, 2010

By A. Mitrašinovic, A. Wolf

"The aim of this investigation was to determine the most suitable additive for recovering metals from converter slags generated during Ni extraction. Fluxes analyzed were silica and lime and reductants included pig iron, ferrosilicon and copper-silicon compound. Slag was settled at 1300°C for one hour to simulate the smelting environment. The newly formed matte and slag were characterized by chemical composition and morphology. Microstructural studies showed that slag formed after adding reductants consisted of primarily fayalite, with traces of magnetite. Entrained matte was present in the slag mostly as prills of Ni3S2-FeS matrix and a Cu2S-FeS secondary phase below 10µm in diameter. Kinetic parameters of matte formation, valuable metal recovery rates and partition coefficients were deduced. Silica additions generated higher partition coefficients for copper and nickel than the addition of lime. Additives used as reducing agents had higher valuable metal recovery rates and partition coefficients. Silica additions favoured the formation a higher grade matte while lime additions will hinder metal recovery. Pig iron, ferrosilicon and Cu30Si were the most effective reductants for valuable metals recovery. Cu10Si and coke additions had little to no effect on valuable metals recovery."

Jan 1, 2015

By José Aparecido Pereira

Este trabalho descreve uma nova metodologia para análise de calibração de cantoneira bem como realizar alterações de calibrações existentes, usando para isto a fórmula de Ekelund. O ponto chave da metodologia é a transformação dos passes de cantoneira em passes planos e a determinação dos coeficientes de alargamento de cada passe. O levantamento dos fatores foi baseado em projetos existentes e em amostras coletadas em laminadores.

Aug 17, 2017

By R. G. Knickerbocker, A. L. Fox, J. Koster, P. R. Perry

"During the past several years, alunite from the Marysvale (Utah) region has been the subject of investigation by the Electrometallurgical Section of the Bureau of Mines. The nature and occurrence of this mineral, with considerable data on the Utah deposits, together with a number of results of preliminary experiments, have been given in a previous report. 6/ The geology of the Marysvale region has been reviewed recently. 7/The present paper reports the results obtained by a method involving the sintering of alunite with boric acid and subsequent treatment of the sinter to produce alumina and potassium sulphate.The preliminary work just mentioned had given indications of the separation of sulphate salts high in potassium from fusions of alunite with borax glass.During the course of further work along those lines, fusions of boric acid and alunite were tried. No separation of salts was obtained, but it was observed that rather complete removal of so3 from the alunite occurred and that the sinter could be leached with water to give a solution contain¬ing most of the potash and a residue containing most of the alumina. The reaction that takes place can probably be written 8/:"

Mar 1, 1939

By R. D. Brittain

In order to analyze and control the transport of harmful trace-element impurities in various smelting processes, it is necessary to have fundamental information about the chemical thermodynamic properties of the pertinent condensed and vapor phases. This paper describes recent thermodynamic studies of the gaseous arsenic sulfides and of the activity of arsenic in a copper-iron sulfide matte phase. These studies were carried out by high temperature mass spectrometry and by effusion vaporization techniques, which permitted clear identification of the molecular species involved, a decided advantage in such complex systems. The nature of the results obtained and comparisons with previous interpretations will be described.

Jan 1, 1983

By Henrique Hipolito, Caio Alves

Waelz process is a method applied in the zinc oxide production and is one of the largest sources of carbon emissions within the zinc industry. The solid carbon used for heating and for reduction reactions is provided mainly by the coke fed with the EAFD in the Waelz kiln. Both chemical composition and physical properties of the coke are important to transportation and to the process. Decarbonizing the Waelz process by replacing the traditional fuel source using alternative biogenic fuel, for example, offers a potential solution to reduce the carbon footprint, which is aligned with the ESG perspective.

Sep 29, 2023

By D. A. Reynolds, L. P. Rockenbach

"The method of analyzing light oil for benzene is fully described by Fieldner and others 4/ and Kester and Kolmes 5/. In this procedure, benzene is determined by shaking 20 cc. of the 79º to 81º C. boiling point cut from the fractionation of the refined light oil with 3 volumes of 98—percent sulfuric acid in an A. S. T. M. separator funnel of the type used for determining water in bitumi¬nous materials. After the mixture has been shaken 5 minutes it is allowed to settle at least half an hour and the acid is drawn off; the residual oil is reported as paraffins and the decrease in volume as benzene. The method has been found satisfactory for light oils from coals carbonized at 5000, 600°, and 7000 C. but does not give accurate, reproducible results for oils from the 800° C. tests.The content of benzene of the 790 to 81° C. cut is high, 90 to 95 percent, for 800° C. light oils, whereas for lower—temperature light oils it is considerably less. Benzene is the most difficult of the aromatics to sulfonate, hence the acid concentration must be maintained above 95 percent to insure complete sulfonation. Sulfuric acid (98 percent) reacts with benzene, but its reaction with paraffins at ordinary temperatures is negligible; however, more concentrated acid will attack paraffins and give erroneous yields of benzene. The reaction between benzene and sulfuric acid forms water that will dilute the acid. The effect of this dilution may be overcome by increasing the acid-to-oil ratio or increasing the strength of the acid. The latter, however, must not be used, because the stronger acid reacts with paraffins."

Mar 1, 1942

By Fred C. Bond

The perennial subject of comminution is deserving of a fresh approach if one can be found. This is attempted here by directing attention primarily to principles rather than to theories. While theories attempt to explain how a certain process acts, principles delineate the laws which the action-must follow. Comminution may be defined as the progressive separation of particulate matter. At the present time this is accomplished commercially by applying energy in the form of compressive and, shearing forces. Such forces strain and distort the particles they contact. When-the applied stress locally exceeds the breaking strength at the weakest flaw in the particle, a crack tip forms. The surrounding strain energy flows to the crack tip, which rapidly extends through the particle as a break. The minute changes in shape and the resulting energy flow cause the failure of other highly stressed flaws, with the consequent formation of a progeny (1) of new smaller particles out of its destroyed progenitor. The applied mechanical energy is transformed into strain energy as the particle is distorted, and then into heat when it fails. Only a tiny fraction of the order of 1/1000 of the applied energy necessary for breakage appears as new surface energy in the product particles. The comminution problem is the relationship between, energy input and product particle size. Its solution is of great-economic importance,

Jan 1, 1961

By Shadia Ikhmayies

Thermo-Calc software was used to investigate the phase diagram of the calcium silicon (Ca–Si) system for the range of Si mass percent 0–100, and temperature range T = 200–1800 K. The melting points of Ca and Si deduced from the phase diagram are very close to the values obtained experimentally. Three stable intermediate solid phases were found, which are Ca2Si, CaSi, and CaSi2, where the first one appeared in the Ca rich side of the phase diagram, and the third one in the Si rich side. In addition, three eutectic points were found at Si mass percents of 3.95, 33.00, 62, and temperatures T = 1048.7, 1519.14, 1308.5 K respectively. Atomic Si (Diamond structure) is found mixed with CaSi2 intermediate phase for temperatures less than 1305 K, and mixed with a liquid CaSi for higher temperatures. These results are important for thermodynamic and metallurgic studies of these intermediate phases.

Mar 1, 2018

By R. Steven Izatt

Green chemistry principles will be discussed, and examples will be given of the use of Molecular Recognition Technology (MRT) to selectively separate specialty metals such as cobalt, nickel, bismuth, rhenium, molybdenum, indium and germanium from various primary and secondary feed streams. Recovery of these metals has numerous advantages including (i) conservation of valuable resources, (ii) prevention of environmental damage, and (iii) elimination of capital and operating expenses due to re-processing or disposal of metal-bearing streams.

By Edward S. Plotkin, Gary A. Almeraris, Thomas F. Peyton

The lining of the tunnel and shafts for a new section of New York City's- water system required extensive components to produce, deliver and place a continuous tunnel linning. The project placed approximately 153,000 CM (200,000 cy) of concrete for 5,340 M (17,520) of drill and blast 7.3 M (24 ft.) ID tunnel, located at depths of 152 M (500 ft.) to 213 M (700 ft.) . This section of tunnel will be connected to the surface water distribution system via four shafts of varying diameters ranging from 5.8 M (19 ft.) ID to 1.5 M (5 ft.) ID . All work was done beneath the streets of Manhattan under the rigid constraints of the City of New York and the Bureau of Water Supply regulations.

Jan 1, 1987

By Felipe Lacerda Giro

Atualmente, a soldagem por extrusão de peças semi-acabadas (chapas) em PEAD tem se mostrado como uma solução atraente para a fabricação de pequenas embarcações de serviço. Neste sentido, a qualidade da soldagem torna-se um elemento fundamental para a garantia da integridade estrutural da embarcação. Neste trabalho são apresentados os resultados da análise da influência de diferentes fatores na qualidade da soldagem por extrusão de chapas de polietileno de alta densidade. Os fatores analisados envolveram o aporte de calor, a preparação do chanfro, a velocidade de soldagem e a pigmentação do fio de solda. A influência de tais fatores na qualidade da solda foi avaliada tendo como referência os resultados de ensaios de flexão em corpos de prova.

Aug 17, 2017

By R. E. Brewer

Pilot scale flotation tests were conducted with a 1-ft-diam column at the Barrick Resources (USA) Mercur mine, Tooele County, UT, to scavenge unleached (0.01 to 0.018 oz/st) gold values from the tailings of a carbon-in-leach (CIL) circuit. The optimal recovery was 35 pct of the unamenable-to-leaching gold, at a grade of 0.353 ounces of gold per short ton, using a mixture of dithiophosphate, xanthate, and diesel fuel as a collector. This was achieved by floating approximately 1.6 wt pct of the CIL tailings. The gold values are believed to be contained in arsenic-bearing minerals, attrited carbon, and carbonaceous material in the ore. Redox potentials were measured with a gold electrode during the conditioning stage prior to flotation. The correlation between flotation recovery and redox potential values could be used to control reagent additions. Treatment of a previously leached and weathered tailings material, averaging about 0.055 ounces of gold per short ton, was also investigated using the column. The tailings were first water leached at approximately 600 C, and the water-leached tailings, which contained approximately 0.03 ounces of gold per short ton, were then fed to the column flotation unit. The effects of pH and sodium sulfide addition on gold flotation recovery and redox potentials were examined. maximum gold recovery, 36 pct, was achieved at pH 8.5 with a sodium sulfide addition of 0.18 lb/st.

Jan 1, 1989

By A. J. Kraemer

"During the past several years a great deal of discussion has centered around the question of the permissible limit of sulphur content in fuels for automotive and aviation motors. Under certain conditions of operation, sulphur in motor fuels causes the formation of corrosive substances which attack bearings, wrist pins, and other parts of engines. On the other hand, in making gasoline from certain stocks, the gasoline fraction normally contains a relatively large proportion of sulphur compounds. By the generally used processes of reducing the sulphur content, a significant part of the gasoline fraction is lost as motor fuel, and added expenses are entailed for chemicals, labor, and other process costs. This condition has been an economic burden to some refiners of high-sulphur crudes. In some instances the treating losses have been rather severe and the treating costs relatively high, but the data presented in this paper indicate that the reduction of sulphur content of motor fuel is a problem to a relatively small number of refiners and of little or no concern to the remainder; in fact, more than 90 per cent of the 153 samples analyzed passed the Federal specification requirement, Which limits the sulphur content to 0.10 per cent. 3This report is based upon the results of an examination for sulphur content, Doctor test, copper strip corrosion, and color of the samples collected during January, 1930, for the twenty-first semiannual gasoline survey of the Bureau of Mines. The results of the gravity ad distillation tests of the survey were published as Report of Investigations 2995. The numbering of the samples given in this report is the same as in Report of Investigations 2995; for example, No. 25 of this report is the same sample as No. 25 of Report of Investigations 2995."

Jun 1, 1930

By Dunlop A. C

A brief study from the Mt. Bulga prospect com- pares the chemistry and mineralogy of different soil fractions and other materials to suggest a sequence of surficial metal dispersion from adjacent gossans, which may have relevance for geochemical exploration in semi-arid terrains. v v v v v JIV-- v v v v a o v o/ v v v v 1 v v lv ./v '' 1 v 16400N ..I v 1635014 v 1630014 .:1 ò.t SILURIAN sillstone " lelsic volcanic sillstone -sandstone ORDOVICIAN Eandesite o quartz float gossanò pits doOP Iv o shalt v _--'fault v 1---1 soil traverse v v v v 0 100 200 mm e Fig. I Local geology and location of soil traverses, Mt. Bulga (compiled from Chisholm, 1976). The Mt. Bulga prospect in central New South Wales is a small but well documented volcano- genic massive sulphide occurrence (450,000t of 0.8% Cu, 1.3% Pb, 5% Zn and 0.45 g/t Au) Cambrell and Kirk (1974), and Chisholm, (1976). Mineralization is localised near the interface of felsic pyroclastics with overlying silt- stones and along adjacent faults (Fig. 1). In this area with a Koeppen type cf6 climate, soils are thin and skeletal along ridges with thicker and better differentiated profiles with a colluvial component up to 2m thick developed

Jan 1, 1988

By Fiorella Polanco Martínez

El presente trabajo describe una forma de financiamiento en la minería a través del mercado de valores. Es decir, que desde un análisis del sector minero se busca convertir las reservas minerales probadas en un patrimonio fideicometido que avale una emisión de bonos titulizados. En este sentido, las reservas minerales por sí mismas carecen de valor económico pero se pueden valorizar con un proyecto de factibilidad futuro, cuya titulización de reservas minerales, se convertirá en una herramienta de financiamiento alternativa o complementaria a la BVL Venture Exchange. Po ello, el financiamiento que se obtenga a través del mercado de valores se destinaría a la ejecución del proyecto minero junior o para expandir uno en producción.

Sep 12, 2005

By Thomas A. Simpson, Tunstall R. Gray

The Birmingham district first produced steel from Alabama hematite ores in 1899. Since then, the district generally produced more than 6.0 million gross tons of ore a year to the late 1950's. Production has declined since then to an annual rate of about 1.5 million gross tons. Reserves calculated for the district are sufficient to last many years. Mining in the district is now confined to Woodward Iron Company's Vance and Pyne mines. The rocks exposed consist of about 15,000 feet of consolidated Paleozoic sediments with a thin veneer of unconsolidated Cretaceous sediments in the Vance area. The district is characterized by a distinctively parallel and subparallel, slightly arcuate series of faults and joint systems. In view of available information, it seems reasonable to conclude that the Birmingham red ores are of sedimentary origin, modified to a small extent by diagenetic replacement after original deposition.

Jan 1, 1968

By R. L. Loofbourow

Most wet mines face unquantified water costs as well as the obvious wing costs. Both kinds of cost are multiplied by work at greater depth and by higher unit prices. This intensified challenge merits renewed or perhaps altogether new response. Any practicable way to reduce inflow tackles both obvious and unquantified costs. Ten groups of possible ways to do it are cited. Most have been demonstrated. Two are known from work other than mining. Surely new means can be found. Here are opportunities for operators of wet mines!

Jan 1, 1980

By Elenice Cavichioli Borba

A dissolução de precipitados ricos em Nb durante o reaquecimento de placas é uma das etapas mais importantes no processamento dos aços microligados. O conhecimento do teor de nióbio em solução ao fim dessa etapa é essencial no projeto termomecânico do aço. Neste estudo, aplicou-se a termodinâmica computacional para avaliar os efeitos do ciclo de reaquecimento de placas sobre o teor de nióbio dissolvido na austenita. Os resultados mostraram que, para determinado ciclo, há um limite máximo de tamanho de precipitado que pode ser dissolvido e que a homogeneidade da distribuição do nióbio em solução na austenita é dependente do ciclo empregado. Os resultados indicam que é possível aplicar ferramentas de termodinâmica computacional para otimizar os ciclos de processamento dos aços microligados.

Oct 30, 2017