Search Documents

By George E. Valadão, Iván A. Reyes, Mizraim U. Flores, Armando C. Araujo, Rubén H. Olcay

Dewatering tailings to higher grades than paste produces a stable deposit that typically does not require retention dams and is called a “dry stack.” A proposal of different dewatering techniques applied in the fine tailings produced after final desliming phase, obtained from the treating of phosphatic ores, is the main objective of this work. The dewatering techniques evaluated were column thickener, deep cone classifier, and hyperbaric filtration. Calcite and dolomite were the main mineral contained in the phosphate tailings and these have a very fine granulometry; the tailings presented different behaviours related to the dewatering technique applied. The test column thickener and deep cone classifier with the best operational parameters found to obtain a maximum percentage of solids in mass were ~ 71% and ~ 67%, with values of yield stress ~ 200 Pa and ~ 100 Pa, respectively. In the hyperbaric filtration, a cake with ~ 10% moisture was obtained. This indicates that the transportation conditions are not the same. The overflow turbidity levels obtained from column thickener and deep cone classifier test did not exceed the value 100 NTU, whilst for the filtrate of the hyperbaric filter obtained values ~ 800 NTU. It was possible to preliminary estimate the recovery direct of water, considering each dewatering technique for final disposal of the tailings. The best dewatering techniques obtained were in the following order for the disposal in phosphate fine tailings dams; the hyperbaric filter showed an excellent dewatering capacity with productions rates around 160 kg h− 1 m− 2 for moisture cake of 10%, followed by the column thickener and deep cone classifier with paste ~ 71% of solids (W/W) and high-density slurry ~ 67% of solids (W/W), respectively.

Dec 23, 2023

By Ronald C. W. Webber‑Youngman, Philani Larrance Ngwenyama

Entrapments are a huge risk in underground mines. This happens when miners (or any other persons who have entered underground) survive the initial event of an accident, become trapped or lost in unknown and life-threatening locations after evacuation, and remain unaccounted for. At this point, every second counts, and emergency response is highly desired for any chances of saving survivors. The survival chances of the missing persons depend on how quickly they can be located. Rescue teams are often deployed to search for the missing persons underground. However, the rescue teams are forced to search in random and presumed areas of the mine. This is due to the unavailability of information pertaining to the whereabouts of the missing persons. Not only the provision of accurate locations, but various other types of information such as post-accident two-way communication can enhance the survival chances of the missing persons. This information can be provided by a fit-for-purpose missing person locator system. A wide variety of missing person locator systems are already commercially available, some are in testing phases and others in prototype and development phases. This includes tracking, tracing, location detectors and post-accident two-way communication systems. These systems have unique functionalities, capabilities and limitations; making it difficult for mines to select the most effective, applicable and suitable system specific to their mine. In this study, the user requirements for a fit-for-purpose missing person locator system were developed. The purpose of the user requirements was to provide a guideline to facilitate the system selection process. The user requirements can also be used as a tool to measure and evaluate the performance of the selected missing person locator system. The user requirements were also used to predict the success of the selected system under different missing person incident scenarios. The development of the user requirements showed a potential for many other benefits for missing person locator systems.

Nov 2, 2023

By B. Mishra, Q. Shi

Numerical simulations have been used to investigate roof fall in the past decades. Comparing to the continuum based methods, the discrete element method has been well recognized for its excellent performance in simulating large strain problems and fracturing processes in the rock mass. However, the discrete element method has its limitations. When simulating a large-scale problem, a large number of particles are required, which consumes significant computational resources. In the present study, a 3D numerical model coupled with the finite-difference method (FDM) and the discreteelement method (DEM) was created to simulate the laminated roof failure in an eastern coal mine in the US. In the FDM-DEM coupled model, the laminated roof of the entry is represented by an assembly of bonded particles using PFC3D. The laminated roof is simulated by adding parallel discontinuities. The discontinuities are given certain stiffness and strength in the model. The ribs, floor, and far-field surrounding rock are represented by continuum zones using FLAC3D. The strength of the discontinuities is varied sequentially and the fracturing of the laminated roof was analyzed with respect to entry advance. The results showed that the laminated roof fractures along the discontinuities while an intact roof fractures in a dome shape. Increasing the strength of discontinuity could enlarge the tensile zone inside the laminated roof and hence change the crack distribution. In addition, the crack quantity in the laminated roof behind the advancing face decreases with the increment of discontinuity strength while this trend is not occurring ahead of the advancing face. The simulation demonstrated that coupled method using PFC3D/FLAC3D can reproduce the laminated roof failure in underground coal mines.

Mar 2, 2022

By Fabrício Silveira Garajau

O sopro de oxigênio é a principal operação durante o processo de refino de aço em aciarias BOF (Basic Oxygen Furnace). Este sopro é feito por uma lança de injeção de oxigênio através de bocais supersônicos, que devem ser dimensionados para as condições específicas de operação, como por exemplo, vazões e pressões de oxigênio, altura de banho, altura da lança em relação ao banho, etc. O mau dimensionamento destes bocais tem influência direta no tempo e eficiência de processo, além de comumente resultar em desgaste prematuro dos bocais e na retirada do bico de operação. Este tipo de falha tem sido observado em bicos da Vallourec Brasil. No presente trabalho será apresentada a metodologia de estudos e resultados de análise metalográfica em amostras de um bico de lança usado pela da empresa, além de simulações CFD (Computational Fluid Dynamics) realizadas para se caracterizar o mecanismo de desgaste dos bocais. Estas informações foram utilizadas como base para o redimensionamento dos bocais, objetivando conter os impactos causados pelo desgaste.

Aug 17, 2017

By André Kraszczuk

Esse trabalho avaliou a microestrutura e a microdureza do aço inoxidável martensítico AISI 440B nitretado a plasma em reator de fonte DC pulsada, a 480ºC, por 6 horas e pressão da câmara de 3,3 Torr. Foram utilizadas técnicas de difração de raios-X, microscopia ótica, microscopia eletrônica de varredura (MEV) e microdureza. A camada nitretada apresentou aproximadamente 24 µm de espessura, não tendo sido observada a formação de camada branca, constituída exclusivamente por nitretos de ferro ou de cromo. Entretanto, notou-se, na zona de difusão, a presença de nitretos nos contornos de grão, possivelmente, de cromo. O endurecimento superficial do aço AISI 440B, atingiu valores entre 1417 - 1677 HV0,025, ao passo que o a matriz metálica do aço temperado apresentou durezas de aproximadamente 54HRc.

Aug 17, 2017

By Y. Héroux, A. Chagnon, M. M. Savard

"Résumé- Le gîte de Pb-Zn de Gays River s'accompagne d'anomalies des propriétés de la matière organique (MO) et des assemblages de minéraux d'argile (AMA). L'association entre la minéralisation, la distribution de la réflectance de la MO et des AMA suggère que ces traceurs peuvent servir à l'exploration des sulfures de métaux de base dans cette région.A l'emplacement du gîte, la réflectance varie considérablement (0,80% à 1,88%), pouvant même afficher une baisse avec l'enfouissement, ce qui est interprété comme une altération chimique de la MO. Les valeurs les plus élevées s'accompagnent localement de quelques textures en mosaïque et délimitent une anomalie thermique au centre sud de la région. Parmi les minéraux des argiles identifiés, l'illite et la chlorite sont terrigènes alors que la smectite, la kaolinite et la corrensite sont authigènes et, à l'instar de l'altération de la MO, résultent des nouveaux équilibres chimiques créés suite à la précipitation des sulfures.Abstract- The Gays River Pb-Zn ore deposit is associated with anomalies defined from the characters of the organic matter (OM) and from the clay minerals assemblages. The relationships be­ tween these anomalies and the mineralization at the mine suggest that these parameters can be used as new guides for the exploration for base-metal sulfides in this area.The vitrinite reflectance (RJ shows a wide range of values (0.8% to 1.88%) and exhibits an anomalous suppressive effect with depth of burial at the mine site, suggesting a chemical alteration of the OM. The highest R, values are associated with mosaic textures and outline a thermal anomaly at the south-center of the studied area. Among the identified clay minerals, illite and chlorite are terrigenous, whereas smectite, kaolinite and corrensite are authigenous and, like the alteration of the OM, are due to the new chemical equilibria resulting from the precipitation of the sulfides."

Jan 1, 1994

USBM Contract H0133045 consists of the design, build and test of 50 waveform generators. The waveform generator is a small ULF transmitter operating in the 1 to 3 KHz frequency range for the purpose of locating trapped miners during a mine disaster. This contract provided for the design, test, and building of 50 waveform generators using a discrete component construction with an option of using hybrid construction techniques within 105 days after the effective date of the contract. Because of large quantity economic considerations, this option was not initiated. Two engineering models were designed, constructed and tested and 50 final production units were fabricated using discrete construction. Complete documentation is supplied under a separate package which includes final schematics, parts list, layout information, equipment specification, production test procedures and qualification test procedures. Ten units have been delivered to the USBM. The remaining 40 units are being retained for packaging under contract H0242010 Transmitter Package and Receivers. A great deal of experience has been gained as a result of this contract. A final discrete potted printed circuit configuration has been arrived at that is now ready for field testing. After field testing, any desired changes should be incorporated into a final design. However, as a result of the current experience gained building and testing the production units, this printed circuit package together with potting procedure could be improved to reduce future costs. For example, the printed circuit board could be increased in size by 0.125 to 0.2 inches and all components could be mounted directly to the board eliminating costly hand stacking of components. The new printed

By Roy L. Soderberg

Ground support for metal, nonmetal, and coal mines was examined through fill placement with a pneumatic stower to increase extraction, reduce ground pressures, and improve general mine safety. Several pneumatically stowed stope-fill products were tested to determine the effects of specific gravity, gradation, moisture, and impact velocity on the in-place density of the stowed fill. Hydraulic sand filling has now served the mining industry for several decades but because of the low density does not always provide ample support to the hanging wall; therefore, the sill and crown pillars sometimes build up excessive stresses that are detrimental to mining. Cementation of a dense fill adjacent to a pillar to allow 100-pct extraction of the pillar, or a fill that can be placed without the use of water and where water is a detriment to rubber-tired mining equipment, was found to be a possible use of pneumatic fill. Placing of coal mine washery products into abandoned underground workings is another possibility in order to completely eliminate surface impoundments.

Jan 1, 1976

By H. R. Zhang

In this paper two optional production processes are presented for reasonable utilization of primary sylvinite in Qinghai province, China. The two kinds of products as chlorine-free potash fertilizers; potassium sulphate or potassium magnesium sulphate can be obtained. In the course of potassium sulphate production, using primary sylvinite from Qinghai salt lake as raw material with impurities such as sodium chloride and insoluble in primary sylvinite, it must be prepared by flotation before being converted into potassium sulphate. This final product has found wide use in tobacco industry in China. However, in some cases Chinese farmers would rather buy the fertilizer of potassium magnesium sulphate than high quality of potassium sulphate. With flotation process which is a little different from above mentioned, the potassium magnesium sulphate fertilizer may be produced by washing one of the flotation concentrate presented as picromerite, while another concentrate containing potassium chloride is treated as by-product.

Jan 1, 2014

By W L. Daniels, C Stilson, C Zimmerman

Mineral sands mining for ilmenite, rutile and zircon has disturbed over 1000 ha of prime farmland in Virginia (USA) since 1997 and additional areas are likely to be disturbed in Virginia and North Carolina (USA) over the next 15 years. Full-scale mining operations at the Old Hickory Project in Virginia were initiated in 1997 by Iluka Resources Inc. and restoration protocols have continued to evolve in response to a variety of economic, technical and social issues. Early on, the return of these lands to agricultural row-crop production was complicated by vertical stratification of tails + slimes and lateral variability in soil physical conditions in the reclaimed pits and by limited topsoil return. Virginia Tech and Iluka have worked cooperatively with all stakeholders for over 20 years to review the pre-existing research base, conduct new and innovative site-specific research and thereby provide reasonable expectations of post-mining soil productivity levels. In 2004, Virginia Tech, Iluka Resources and a local leaseholder (Carraway-Winn family) agreed to jointly manage a 45 ha research demonstration farm where the long-term effects of alternative soil reconstruction practices are being rigorously monitored for both row crops (corn and wheat) and forage production. All mined land crop yields are also compared to an adjacent undisturbed exceptional quality prime farmland soil. Row crop yields between 2005 and 2010 were significantly above county average yields (regulatory target level) and approximately 75 - 80 per cent of undisturbed adjacent prime farmlands. The state regulatory authority has recently relaxed its position on the necessity of topsoil return versus use of topsoil substitutes based on appropriate on-site research results and the ability of the reclaimed soils to meet comparative local county crop yield targets. This cooperative effort allows all clientele groups to objectively assess the post-mining productivity of these mined lands while providing an invaluable educational opportunity for the mining industry. CITATION:Daniels, W L, Stilson, C and Zimmerman, C, 2012. Development of effective rehabilitation protocols for mineral sands mining in Virginia, USA, in Proceedings Life-of-Mine 2012 , pp 97-104 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 10, 2012

By Teuku A. R. Putra, Patrick R. Taylor

Various pyrometallurgical methods for treating copper concentrates that contain appreciable arsenic are reviewed. Various aspects of the engineering of these treatment methods are discussed. The methods discussed include: complete oxidation with arsenic fixation; selective volatilization of arsenic; acid baking, soda ash roasting, and others methods. Methods for the ultimate disposal, or marketing, of the arsenic are discussed.

Jan 1, 2014

By Gordon H. Dechman

This report presents the concept, design, and testing of a sonic velocity monitoring system for the early detection of slope failure in open pit mines. The heart of the system is a device for producing reproducible sonic signals in rock. Because changes in the velocity of sound through rock near the top of the pit wall are a measure of extent and rate of fracturing of the rock, velocity histories obtained from periodic, automatic sonic velocity surveys provide positive information about developing slope instability.

Jan 1, 1976

By Claudemir Ribeiro

A lança de injeção de carvão pulverizado (PCI) é um método consolidado na indústria siderúrgica, que possibilita a redução do consumo de carvão vegetal ou de coque de carvão metalúrgico enfornado, além do ganho de produtividade. A seleção de materiais adequados para a lança de injeção é de suma importância para agregar ainda mais valor ao método. A finalidade deste trabalho é nortear a seleção das ligas aplicadas em alta temperatura, visando o melhor custo benefício, por meio das análises da resistência à corrosão, fluência e estabilidade estrutural. Foram realizados testes em uma usina siderúrgica chinesa com as ligas Sandvik 253 MA™ (UNS S30815) e UNS S32109. A experiência demonstrou como as siderúrgicas podem obter ganhos com a seleção adequada da liga. O custo-benefício do 253MA que é ligado ao Cério, Silício e Nitrogênio, mostra-se como uma ótima alternativa para o processo de injeção de carvão, devido a sua alta resistência à oxidação, à fluência e à erosão. Outras ligas como UNS S30403, UNS S31009 e UNS N08810, que são muito utilizadas em alta temperatura nas indústrias em geral, também foram analisadas como comparativo.

Aug 17, 2017

By C. Dorfling, W. A. Rossouw

"Hydrometallurgical processes used for metal recovery from waste printed circuit boards (PCBs) typically involve dismantling, shredding and physical separation prior to successive leaching stages for selective dissolution of different metals. The principles of the physical separation units are well understood, but valuable metal losses of more than 30 % can be incurred during these processing steps. The impact of the physical separation units’ performance on downstream leaching operations have not been defined; this prevents the development of a well-integrated process. The objective of this project was to determine to what extent the base metal leaching behavior depends on the physical separation pre-treatment. PCBs were shredded to 100 % passing 2 mm before physical separation by dense medium separation (DMS) as well as magnetic separation. Batch leaching tests using various concentrations of sulfuric acid were conducted on three feed fractions: (1) shredded PCBs without any physical separation, (2) heavy fraction recovered from DMS, and (3) non-magnetic fraction recovered from the DMS heavy fraction. DMS increased the metal content in the feed from 48 % to 75 % on a mass basis, but 70 % of the gold and 20 % of the copper reported to the light fraction. The application of magnetic separation to the heavy fraction produced by DMS removed 67 % and 61 % of the iron and nickel, respectively, while negligible amounts of non-magnetic metals were removed. Although DMS successfully concentrated the feed and magnetic separation removed the majority of iron and nickel, these steps did not result in any improvement in the rate or extent of copper leaching. Metals generally leached faster when the sulfuric acid concentration was increased from 1 M to 2.5 M; this effect was seen to be more pronounced for pretreated feed. INTRODUCTION The fast rate of technological development has led to a decrease in the service life of electronic devices. This is resulting in an increased rate of electronic waste generation. The recovery of metals from electronic waste is of environmental and economic interest. The majority of these metals are typically located on printed circuit boards (PCBs) within electronic devices (Tuncuk, Stazi et al., 2012). Hydrometallurgical processes are considered a viable option for small scale metal recovery from waste PCBs, and generally involve the following steps: disassembly for removal of hazardous and reusable parts, size reduction, physical separation, successive leaching stages for metal dissolution and finally recovery of metals from leach solutions."

Jan 1, 2018

At its Copper Cliff Smelter, Inco Limited processes a bulk copper-nickel concentrate in two Inco oxygen flash furnaces. The furnace matte is converted to low iron matte for further processing, and the molten converter slag is recycled to the flash furnaces. The flash furnace slag is discarded. Natural gas or coke supplies a minor proportion of the process heat requirements, thus limiting the flash furnace matte grade to the target 45% CuNiCo. Coke addition to the furnace offers a potential means of establishing a reducing barrier on the surface of the molten bath. Such a practice would be conducive to producing sulfur deficient (partially metallized) matte. At the same iron content, the iron activity of sulfur deficient matte is higher than that of regular matte. A supernatant coke barrier could, therefore, be expected to lead to higher nickel and cobalt recoveries, reduction or even elimination of magnetite furnace bottom build-up and increased sulfur elimination as SO2 in the flash furnace. Preliminary experiments were conducted in a mini plant flash furnace to investigate the effect on process metallurgy of the suggested modified scheme. This paper presents the experimental results and discusses key aspects of the possible operation of the Inco flash furnace with a coke barrier separating the freeboard from the molten bath.

Jan 1, 2003

By I. Gaballah

Decontamination of synthetic solutions of PbC12 containing 10, 100 and 1000 ppm of lead, using chemically treated barks had been studied. The percentage of !cad cations' removal from solutions depends upon the pH and the initial concentration. About 99 % of the initial lead content can be removed at pH of about 3.5, 5.5 and 6.5 for initial concentrations of 10, 100 and 1000 ppm respectively. The maximum retention capacity of the treated bark is about 83 mg of lead per gram of modified bark. Bark loaded with lead had been analyzed by Infra Red spectroscopy. It seems that lead reacts with hydroxyl groups of the phenolic constituents of the bark. On the other hand, the removal of a lead cation by the bark leads to the release of two H+. This seems to show that the removal of lead could be interpreted as an ion exchange with hydrogen belonging to the hydroxyl groups of the modified bark.

Jan 1, 1994

By Collins M. J, Ozberk E

A major advantage of the Sherritt Zinc Pressure Leach Process is the conversion of sulphide sulphur in zinc concentrate to elemental sulphur during pressure leaching. Elemental sulphur can be recovered as a marketable byproduct by flotation of the leach residue, and melting and filtration of the sulphur flotation concentrate. The behaviour and deportment of sulphur during pressure leaching, flotation, and melting and filtration are discussed in this paper using data obtained from the treatment of a wide variety of zinc concentrates in the laboratory miniplant at the Sherritt Research Centre. The quality of the elemental sulphur byproduct and a process for purifying the sulphur are also Presented.

Jan 1, 1993

By Long Han, A. V. Kalinin, Xiujian Luo, Xiaobo Wang, Xiaoou Xia

"Inertia vibration crusher is a kind of vibration equipment which crushes ore by vibration. When the inertia vibration crusher works, ore between the two moving jaws is subjected to the high frequency contact force, which is produced by the two moving jaws with high frequency synchronous reciprocating motion. The synchronous motion of the two moving jaws depends on the self-synchronous feature of the inertia vibration crusher. To study the self-synchronous feature of the equipment, the dynamic model was established, in which relative parameters were taken into consideration. The kinematic coupling relations of the assemblies are discussed, and appropriate calculation method is chosen to solve the vibrating differential equation. Whether the two vibration exciter can realize synchronous operation depends on the ability of the vibration system's capture moment. Results show that though the two rotors’ motors and damping coefficients are different, and two jaws’ damping and stiffness coefficients are also different, as angular velocities of the two unbalanced rotors reach a certain value, the vibrating system can be stable. Their angular velocities tend to be equal, and the swings of the two moving jaws can be the same. The horizontal vibration and swing of the frame are large in a few seconds after starting the machine. When the system runs stably, the horizontal vibration and swing vanish, and the vertical vibration is stable. The study and its results can provide reference for the optimization design and parameter setting of inertia vibration crusher and related vibratory equipments.INTRODUCTIONMaterials can be easily broken by using the inertia force of the vibration exciter, which can effectively realize the selective crushing, reducing excessive combinations and the energy consumption, as introduced by Zhang in 2005. The initial micro crack between crystals in the material increases and new cracks can be manufactured because of the high frequency impact and the extrusion of the vibration crusher, so vibration crushing equipment can make it possible for any high strength brittle material to be broken theoretically. Inertia cone crusher and inertia vibration crusher have been successfully used in the treatment of metallurgical slag and construction waste, and it verifies the efficiency of vibration crushing."

Jan 1, 2016

By R. Herrera-Urbina

Measurements of the electrophoretic mobility of bastnaesite in aqueous solutions of sodium nitrate reveal that the isoelectric point (iep) of this cerium fluocarbonate occurs at about pH 9.3. These results also indicate that the pH affects significantly the electrophoretic mobility of bastnaesite, which becomes more positive as the pH decreases and more negative as the pH increases from the iep. Computations of solid-solution equilibria for the bastnaesite-H2O system closed to the atmosphere as a function of pH indicate that cerium fluoride precipitates in acidic solutions, whereas cerium hydroxide precipitates in alkaline solutions. When the initial amount of bastnaesite is fixed at 0.05 wt.% (the solids concentration used for electrokinetic experiments), these computations reveal that bastnaesite is the only solid phase in the pH range from 5.75 to 8.55, it coexists with CeF3(s) between pH 5.22 and pH 5.74, and with Ce(OH)3(s) between pH 8.56 and pH 10.12. Cerium fluoride and cerium hydroxide are the only solid phase below pH 5.2 and above pH 10.2, respectively. According to these computations, the dissolution-precipitation processes that occur when bastnaesite is equilibrated in aqueous solutions at different pH values determine the solid phases present in the system. In turn, these processes must affect the electrokinetic potential at the solid-solution interface, and they must be considered for explaining electrokinetic measurements as a function of pH when bastnaesite is the original solid phase in aqueous suspensions.

By José Flávio Viana

A redução do custo de fabricação do aço tem como ponto importante o refino secundário, seja com a utilização do Forno Panela, aquecimento químico ou borbulhamento de argônio. A qualidade e tempo de formação da escória sintética tem relação direta com o custo do tratamento. As escórias sintéticas sinterizadas produzidas pela Tecnosulfur contribuem significativamente para a redução do custo total de tratamento do aço nesta etapa.

Aug 17, 2017