Search Documents

By W. H. Ode

An investigation of standard methods for determining ash in low-rank* coals showed that generally 60 to 95 percent of the total sulfur in the coal is retained in the ash as SO3. This large sulfur retention causes a positive error in the determined mount of ash of as much as 6 percentage points for the coals examined, although it usually is 2 to 3 percentage points for lignites and about 1 for subbituminous coals. Unless the sulfur content is low or unless a correction is made for the SO3 retained, the fixed carbon and oxygen have an equivalent negative error when determined by difference; also other inaccurate analytical values occur when the data are calculated on an ash- free bas is. No simple modification of the ashing procedure was found that would reduce the sulfur retention to a point where its effect on the ash determination would not be significant, Therefore, for accurate analytical work on law-rank coals, the SO3 should be deducted from the determined ash to obtain a "corrected" ash value.

Jan 1, 1962

By Drew Martin

In March 2010 the Boral Linwood Quarry, Adelaide South Australia, implemented the blasting contractors Monte Carlo Blast Vibration Model as part of their blast design process. The Linwood Quarry was developing an area where blasting activities were marginally complying with the statutory vibration limits. Compliance to the statutory limits was only being achieved through the use of small blasts (less than 15 000 T (14 763 ton)) at a high cost to the quarry.

Jan 1, 2012

By K. M. Mohamed, I. B. Tulu

"Failures of coal ribs are major hazards in underground coal mines. For the period of 2010 to 2014, rib falls were the leading cause of groundfall fatalities and accounted for 35% of all groundfall-related fatalities. Currently, the National Institute for Occupational Safety and Health (NIOSH) is conducting a research project to develop an engineering-based design methodology for rib control in coal mines to reduce rib fall accidents and fatalities in underground coal mines. Numerical models can be used as part of the design methodology provided the models are appropriately calibrated and verified. The paper presents a coal rib model to simulate the mechanism of the coal deformation and fracturing that can lead to stress-driven rib falls. The proposed coal rib model was calibrated against published data from an instrumented rib site at the West Cliff mine in Australia. Fracturing of the coal rib was defined by critical values of shear strain of the coal material and rib displacement. A critical plastic shear strain of 2.8% and a sudden increase of rib displacement of 30 to 45 mm were sufficient to develop a fracture plane in the rib model. Accordingly, a discontinuous rib deformation was achieved and it compared favorably against field monitoring data. INTRODUCTION Coal ribs are the vertical walls of coal formed when entries are developed in a coal bed. Failures of coal ribs are a major hazard in underground coal mines. Furthermore, failing ribs can contribute indirectly to roof and floor instability by increasing opening widths across intersections and entryways. Over the last 18 years, there has been a continual occurrence of injuries and fatalities in underground coal mines due to rib falls. For the period of 2010 to 2014, rib falls (excluding longwall face and bursts) were the leading cause of ground fall fatalities and accounted for 35% of all groundfall-related fatalities [1]. Despite the threat of rib falls, the amount of rib falls and rib support research conducted in the U.S. is limited compared with what has been done in pillar and roof support design. Currently, the National Institute for Occupational Safety and Health (NIOSH) is conducting a research project to develop an engineering-based design methodology for rib control in coal mines to minimize the number of rib fall accidents and fatalities in underground coal mines."

Jan 1, 2016

The Mine Safety and Health Administration (MSHA) defines an independent contractor as “any person, partnership, corporation, subsidiary of a cor-poration, firm, association or other organization that contracts to perform services or construction at a mine.” Contractors that perform specific types of work are required to report the number of employees who work at coal mines and noncoal mines.

Sep 1, 2007

By B Firth, G OÆBrien, B Jenkins

In coal flotation, particles of different components of the coal such as maceral groups and mineral matter and their associations have different hydrophobicities and therefore different flotation responses. By using a new coal grain analysis method for characterising individual grains, more detailed flotation performance analysis and modelling approaches have been developed. The method involves the use of microscopic imaging techniques to obtain estimates of size, compositional and density information on individual grains of fine coal. The density and composition partitioning of coal processed through different flotation systems provides an avenue to pinpoint the actual cause of poor process performance so that corrective action may be initiated. The information on grain size, density and composition is being used as input data to develop more detailed flotation process models to provide better predictions of process performance for both mechanical and column flotation devices. A number of approaches may be taken to flotation modelling such as the probability approach and the kinetic model approach or a combination of the two. In the work reported here, a simple probability approach has been taken, which will be further refined in due course. The use of grain data to map the responses of different types of coal grains through various fine coal cleaning processes provided a more advanced diagnostic capability for fine coal cleaning circuits. This enabled flotation performance curves analogous to partition curves for density separators to be produced for flotation devices.

Jan 1, 2005

By Steven W. Hunt, Isabelle Lamb, Steven B. Fradkin

Groundwater control is generally an important consideration and significant source of risk during most tunneling projects. Proper baselining of groundwater conditions requires: 1) a thorough understanding of the geological environment; 2) a focused site investigation; 3) identification of construction and adjacent property damage risks associated with inflows and short and long term piezometric level changes; and 4) consideration of contractual issues including restrictions on means and methods and pay items for associated work. This paper provides an overview of groundwater baselining issues and risks based on selected design studies and construction case histories.

Jan 1, 2005

By Knud Sinding

Environmental reporting by mining firms takes many forms and change frequently. The objective of these reports is related to increasing the legitimacy of mining firms with their diverse stakeholders. This study, focusing on internet-based reports, shows that there are considerable variations in reporting. This phenomenon is interesting because it belies the efforts pursued by leading industry members under iniatives such as the Global Mining Initiative and the Mining, Minerals and Sustainable Development project. The observed variation, both internally among reports and between reports and other industry policy statements, suggests that the industry needs to explore the possibilities for more convergence in terms of reporting quality. Based on theoretical constructs from the management literature we present a series of arguments defining necessary and sufficient conditions for durable and well-institutionalized reporting practices and standards.

May 1, 2002

By Albert F. Baker

Techniques were developed and circuitry was assembled for measuring the total and volume resistances to the flow of electric current through solid specimens of anthracite. The two-, three-, and four-terminal test methods demonstrated the extreme sensitivity of resistivity to differences in anthracite characteristics and showed response to changes resulting from variations in structure, temperature, and moisture content.

Jan 1, 1966

By Gaballah Djona M.

Spent hydrorefining catalysts contain about 5 % of CoO and/or NiO, 12 % of MoO3 and up to 10 % of V205. They are generally supported by alumina and contain up to 25 percent of C, S and hydrocarbons. Such materials are potentially hazardous to the soil and to water resources. Selective chlorination of raw unroasted samples with Cl2 + air gas mixture had been investigated. At temperatures lower than 600 °C, it was possible to recover more than 90 % of nickel and cobalt chlorides, about 99 % of the molybdenum and up to 75 % of vanadium chlorinated compounds. CoCl2 and Ni/Cl2 were extracted from the chlorination residues by their dissolution with acidified water. Molybdenum and vanadium chlorinated compounds were recovered by selective condensation from the vapor phase. The chlorination of Al2O3 could be limited to less than 6 %. The scale up of this treatment was successful and a flow-sheet is proposed.

Jan 1, 1995

By Steve Dillingham

Blasting crews, explosive product drivers, drillers, blasters, supervisors, and salespeople all arrive daily at customer blast sites in vehicles of every type whether passenger cars, pickup trucks, or bulk trucks. The majority of these vehicles are company owned and re p re s e n t a substantial investment and risk for the company. That may explain why the costs resulting from blasting incidents is often surpassed by those involving motor vehicle accidents.

Jan 1, 2003

Invensys’ recently introduced Field Device Manager for Foxboro I/A Series distributed control systems provides the industry’s first solution that takes advantage of both the latest Enhanced Electronic Device Description Language (Enhanced EDDL) and FDT technologies. This combination provides comprehensive lifecycle support to configure, calibrate, commission, diagnose and optimize the performance of any vendors’ foundation fieldbus device. The I/A Series Field Device Manager enables users to take advantage of any EDDL, Enhanced EDDL and/or FDT host deliverables supplied by the device vendor.

Jan 1, 2007

By Richard Hamburger

Calculating machines permit the use of the more rapid cotangent and semigraphic solutions of plane triangulation. The results of these methods are as accurate as those of other methods. Simple adjustment of the net, and ease of calculation encourage more complete field work. Errors in field work or in computation are easily localized.

Jan 1, 1950

By D. F. Scott

The purpose of this study was to determine if miners are at risk from exposures to chemicals used in the mining industry, and determine the nature and sources of the illnesses and injuries. The authors reviewed the Mine Safety and Health Administration?s (MSHA) Employment and Accident, Injury, and Illness database and identified 2,705 cases of chemical-related injuries and illnesses that were reported to MSHA from 1999-2006, involving 66 different chemicals. The main source (cause) of chemical-related cases was acids/alkalis (about 39%). The primary nature (effect) of chemical-related cases was chemical burns (about 57%). The job classification where workers incurred the most chemical-related injuries and illnesses was cleaning plant operator/media operator/boney preparation plant operator/crusher worker. The number of nonfatal days lost did not change significantly and overall, the incidence rate of chemical-related cases decreased by 36%. Chemical burns accounted for a large number of injuries; mining companies should carefully examine their personal protective equipment (PPE) requirements, training methods, and safety culture to insure that their workers are protected.

Jan 1, 2009

By John W. Brown

"Adequate dust control in and around rock drills is a problem that must be solvedfor the health and safety of workers running the drill as well as those working around thedrilling operation This paper will discuss the designs available from most drill manufacturers todayand the effort ‘nvolved in keeping them effective on a productive basis."

Jan 1, 1999

By Norman A. Jull

"IntroductionThe scope of this paper is intended to deal mainly with cyclones in grinding circuits. However, the section on Cyclone Equipment, contains more general descriptions, to cover most of the cyclones used in mineral separation plants.Cyclones as heavy media separation vessels are discussed by Mark Freberg (this volume). Their use in tailings deslirning is discussed by P.C. Lighthall, eta/. (this volume).Cyclone EquipmentCyclone TerminologyApexObviously, the apex of a cone is the smallest end. However, with cyclones the term is usually used for the fitting which is attached there to control discharge of the underflow stream.Note that the cyclone need not be so mounted that the apex is the lowest point, although that is the most common method. Keeping the apex below the rest of the cyclone helps avoid plugging when the underflow contains very large particles and the tonnage of underflow solids can fluctuate.Various devices for adjusting apex diameter or otherwise controlling the underflow are discussed later under ""Cyclone Construction"".BypassingThe transport of a portion of feed slurry directly to underflow so that classification is bypassed by that portion of feed.This action is fundamental in any hydraulic classification, whether gravity or centrifugal, because the large particles going to underflow have some void volume between them, which remains filled with feed slurry.D50By definition, D50 is that particle size which has an equal probability of going to overflow or to underflow.It is calculated by drawing a curve of recovery vs particle size and noting the size at which 500Jo recovery occurs.This may be done equally with corrected or with gross recovery (see below) and the resulting value should therefore be identified as d50c (corrected d50) or as d500 (gross d50).Note also that it is common in industry practice to plot size analysis data on the retained size rather than on the average of passing and retained (the middle of the size band). To portray sizing alone it makes no difference, but to read a D50 value off a curve of corrected or gross recoveries, it is essential to plot those values on the average size of each band."

Jan 1, 1989

By Michael McNinch, LaTasha R. Swanson, Jennica L. Bellanca, Justin Helton

Accident data indicates that mobile haulage poses a significant pinning, crushing, and striking risk. Proximity detection systems (PDSs) have the potential to protect mineworkers from these risks. However, unintended consequences of mobile PDSs can undermine the safety benefit they provide. Soliciting iterative user input can improve the design process. Users help provide a critical understanding of how mobile PDSs may hinder normal operation and endanger mineworkers. Researchers explored users’ perspectives by conducting interviews with mineworkers from seven mines that have installed mobile PDSs on some of their haulage equipment. Mineworkers reported that mobile PDSs affect loading, tramming, section setup, maintenance, and general work on the section. Mineworkers discussed the operational effects and increased burden, exposure, and risk. Mineworkers also suggested that improved task compatibility, training, logistics, and PDS performance might help address some of these identified issues. This paper also gives additional insights into mobile PDS design and implementation.

By P. J. Mackey

New and emerging, as well as proven technologies for the smelting of copper, nickel, lead and zinc are briefly reviewed. The number of new technologies available today is greater than at any time in the past, and interest and development activities remain high despite the economic dif-ficulties faced by the non-ferrous metallurgical industry. Part of the impetus is provided by the realization that only the most cost effective producers will remain competitive, and that new technology is one key to cost effectiveness. The commercially proven "new" copper smelting processes can now be considered to be conventional- technology, and are expected to dominate copper smelting for acme time. There is a growing. interest in continuous copper converting, although direct smelting and converting to copper in one vessel remains the- ideal. There is little activity in nickel smelting. After many years. of development, it appears that several new direct lead smelting processes will soon be a commercial reality. The electrolytic zinc process is expected to continue its dominance, although there is a renewed interest in pyrometallurgical approaches. One of the new zinc processes, and a molybdenum smelting process, illustrate the possibilities of using plasma technology in non-ferrous metallurgy. In the area of complex sulphides, there is perhaps less interest in the treatment of bulk con¬centrate, and more in the treatment of so-called dirty copper concentrates. Much of the technology ancillary to smelting has remained relatively unchanged, and more effort must be made to advance the technology in areas such as materials handling, gas cleaning and sulphur fixation, and energy recovery. More attention to engineering design is also needed. Escalating capital costs may make mini-smelters attractive, but imaginative technology and innovative engineering will be required to make them cost effective. Finally, a glimpse is offered of the smelter of the future.

Jan 1, 1983

By P. Klaus

"KfW IPEX-Bank is the commercial arm of KfW Bankengruppe, responsible for international project and export finance.KfW was one of the first banks in Germany to promulgate environmental guidelines for its commercial business activities. These guidelines were first made public in 2000 and updated for the second time in 2004. They now include specific reference not only to environmental but also to social concerns. The guidelines specify the procedures to be followed in assessing credit risks related to environmental or social hazards.The bank considers sustainability as an interdependent framework of economic, ecological and social factors. In its efforts to contribute to sustainable development worldwide the bank uses its influence as far as possible to improve a project’s performance if such improvement is deemed necessary."

Jan 1, 2005

By M Gill, A Mathias

The mining industry has always been cost-focussed but in recent times mining companies have moved towards obtaining a competitive advantage through the implementation and sustainability of best practice in the areas of improved safety, operating costs, quality and productivity. This is the concept of Value In Use û that mining companies see value generated all the way to the bottom line through improved change, and those changes become an established mine practice. Many mining companies do not have the resources or the knowledge to sustainably achieve such an outcome. This has led to companies looking to their suppliers to deliver measured value to their business through partnership arrangements. Suppliers have been able to leverage their knowledge of products, product applications and services to offer alternative supply agreements that bring greater returns to their businesses while improving supplier/client relationships. Orica has developed such a partnership with Coal & Allied in the form of a Continuous Improvement Program. Coal & Allied is based in the Hunter Valley region of NSW and is the largest coal producer in that region. Both parties are contractually bound to jointly deliver Value In Use projects to Coal & AlliedÆs Hunter Valley Operations and Bengalla mine sites. It is the request of the Orica and Coal & Allied Steering Committees that this paper does not include the details of actual projects or the costs or key performance indicators associated with the program. This is to maintain the competitive advantage to both Orica and Coal & Allied through the implementation of such a program. It is in the writersÆ opinion that this paper does not lose any significance through this restriction as the most important component of the Continuous Improvement Program is not the projects themselves but the methodology behind them. With this in mind the paper will discuss the development of Value In Use offerings, the key aspects of the Coal & Allied and Orica joint program, what is a Value In Use project, how to measure its value, finally why and even more importantly what makes this program is a success.

Jan 1, 2004

By R. H. Church, William E. Webb, Walter E. Pittman, James R. Boyle

As part of the Bureau of Mines health and safety research program, a short-range locator system, capable of locating miners who have become trapped following a mine accident, has been devised, The system consists of a lightweight, low-power radio transmitter incorporated into a miner's cap lamp battery and a directional receiver carried by rescuers. Prototype transmitters have been constructed, and the propagation of their signals has been investigated, The detectability of the signal in underground coal mines has also been investigated, This research indicates that a short-range location system would serve as an economical and practical means of locating miners from within the mine following an accident,

Jan 1, 1984