Search Documents

By David B. Reger

New discoveries of gas in the southern counties featured the petroleum industry in West Virginia during 194;. Drilling for oil increased slightly over 1944 and a small increase of initial production resulted. Out of 28 wildcats drilled, there were 16 gas discoveries and 12 dry holes. No commercial oil was found in the 28 wells.

Jan 1, 1946

By Mauro Torres, Gabriel Zarate

"AngloAmerican used the extractant M5640 at Mantos Blancos and Mantoverde and uses PT5050MD at Los Bronces Division, which are aldoxime and modifier blends. In the first case, the modifier is the esther TXIB, while in the second case is the tridecanol TDA. It is a well-known fact that the extractant degrades while the modifier does not and with time the oxime/modifier ratio can change significantly, depending on the operating conditions of each plant.In order to evaluate the effect of this varying modifier content in the plant organic, especially in the organic losses, a complete metallurgical test work program was conducted at laboratory and pilot plant scale by Flomin SNF, a new extractant supplier. Results showed that the addition of an aldoxime without the modifier did not affect the chemical performance of the extractant, but there was a significant decrease in the viscosity and density of the organic.Based on the results obtained in the metallurgical program, it was decided to run plant scale tests at the SX plants of Mantos Blancos and Mantoverde. In these tests, instead of adding extractant to maintain the organic inventory, CuPROMEX 3406 which is an unmodified aldoxime was added until the original oxime/modifier ratio was reached. This was obtained after 6 months of operation and since then both plants are running with the extractant CuPROMEX 3302 both supplied by Flomin SNF.In the case of Los Bronces, the pilot plant work was completed and it is programmed to run similar plant scale tests. In this case, the oxime/modifier ratio increased and TDA will be added until reaching the original ratio.The plant results obtained at Mantoverde and Mantos Blancos, together with the pilot plant test results obtained at Los Bronces, are discussed in this paper."

Jan 1, 2016

By W. C. Phalen

E. G. SPILSBURY; New York, N. Y.-I would like to emphasize what Mr. Phalen says in his paper regarding the possible utilization of the waste acids in the West for the acid concentration of phosphate rock, and to call attention to the fact that this is already being done by Mr. Laist at Anaconda, who is producing concentrated phosphoric acid from these low-grade rocks. During the last year, he has not been able to carry this along to the extent he, had expected, owing to the tremendous demand which they have had for all the acid they can produce, so instead of having a. surplus of acid, as was expected, they are really short of this material for their electrolytic copper and zinc work.

Jan 4, 1917

IRVING. PERRINE, Hutchinson, Kans.-I think in reading this paper one should hear in mind its relation to Dr. David White's paper on "Some Relations in Origin between Coal and Petroleum."' In that paper he discusses the relationship between the percentages of fixed carbon in the coals, the gravities of the oils, and commercial gas possibilities. His paper has a map showing certain areas which Dr. White believes to be hopeless as far as oil and gas possibilities are concerned. THE CHAIRMAN (C. W. WASHBURNE, New York, N. Y.).-I. would like to emphasize one point brought out by Professor Schuchert.2 The southern hemisphere has had an exceedingly monotonous geological his-tory, except the northern border of Africa, the eastern border of Aus-

Jan 12, 1919

By S. Marsland

Reference materials have always been important for validating and controlling analytical methods. They have recently become even more important as quality requirements have become more stringent and customer demands for properly verified and controlled results increase. Clients, especially from the resource exploration industry, demand critical validation of all results reported. Mintek has been producing geological and semi-processed ore references since the early 1970s and recently, due to increase in demand, other manufactures have entered the South African market. This paper describes analytical challenges from the customers? perspective, the customers being metallurgists, mine geologists, environmental scientists and geologists from resource companies. Reference materials with their appropriate use and a good understanding, can aid greatly in building confidence in the results, choosing the right laboratory for a project, deciding which set of results is correct and providing evidence to the customers? clients that the best possible results have been obtained

Jan 1, 2007

Metal Statistics, Published by the American Metal Market, 111 John St , New York, N. Y. While it is not policy to list in this directory commercial publishers of literature on mining and geology, it is felt that reference to a few standard works of wide distribution and general use should be included; particularly when those works are statistical or of a specific informatory nature Metal Statistics is a book issued annually by these publishers. It contains a general assortment of statistical information concerning the ferrous and the nonferrous metals-price quotations of the metals, tables of production, and so on It is a widely used reference The 25th Annual Edition was issued in March, 1932. The price is $2

Jan 1, 1933

By John L. Walte

Consolidation Coal Co.'s Renton mine, a 680 000-t/y (750,000-stpy) underground operation located in western Pennsylvania, has reduced the time required for overcast construction in its advancing operations by adopting a prebolting technique followed by multiple blasting. In the past, the mine's overcasts had been excavated by the continuous mining machines used to advance the section. More recently, the overcasts were blasted down and then rebolted with a stoper drill. The new system, using a two-part combination bolt, has proven very successful in speeding up overall construction time and providing more positive horizontal control in blasting. The prebolting approach allows the roof to be blasted down and loaded out without the need for rebolting the shot-out area.

Jan 6, 1978

By AIME AIME

THOUGH Frank Wardlaw was born in the East- at Schroon Lake, N. Y., on July 14, 1887-and was educated in New York City-Columbia, E.M., 1916 he has spent his entire professional life in the West, and is still there, as assistant general manager of the Inspiration Consolidated Copper Co., in Arizona. His first jobs were as miner and surveyor for the Utah Consolidated Mining Co., at Bingham, where he worked under A. S. Winther, now general manager of Inspiration's adjoining big neighbor, the Miami Copper Co. After rising to the position of chief engineer and geologist, Mr. Ward- law left Utah Consolidated to go to Chile for two years with the Braden Copper Co. Then he returned to his

Jan 1, 1940

By Wen Songlin

This paper presents an experimental program to investigate the behavior of a pile with wings under horizontal loads in sand at laboratory. The work focused on evaluating the lateral resistance behavior and the geometric effect of wing board on the horizontal resistance. Based on the measured data and observed phenomenon, the following behaviors have been observed: 1) A pile with wings is not only a powerful means to improve the horizontal bearing capacity of a pile foundation but also economy and feasibility; 2) The horizontal bearing capacity of a pile with wings increases with increasing of it?s wing board?s area; 3) The pile lateral capacity is also influenced by the wing board?s geometric shape. Under a certain soil and pile condition, there is a critical embedment depth of the wing board, which will yield the maximum horizontal bearing capacity. It was further observed that when the displacement of the pile head increases, part of the horizontal bearing capacity of the pile is developed by the so-called shaft?s anti-pulling capacity.

Jan 1, 2007

Six pioneers of the American mining industry will be inducted into the National Mining Hall of Fame on Saturday, Sept. 13, at the Museum Convention Center in Leadville, CO. The 16th annual Mining Hall of Fame induction banquet will begin with a reception and open house at 5:30p.m., followed by the dinner and program at 7 p.m. The six inductees include James M. Gerstley, the only living member, and George O. Argall, Jr.; John F. “Leadville Johnny” Campion; Charles R. Nailler; Edwin N. Pennebaker and Russell L. Wood.

Jan 1, 2003

By G. C. Branner

The bauxite diagram presented as figure 1 was developed to clarify, by graphic means, the theoretical chemical constituents of gibbsite-kaolinite-type bauxite for all possible proportions of these two minerals from pure gibbsite to pure kaolinite. The tables in the report reflect the same date. The diagram provides (1) a graphic representation of the relations of constituents with respect to a ill possible percentages of alumina and silica, (2) a basis for verifying the accuracy of analyses of gibbsite-kaolinite bauxite, and (3) a basis for estimating the type and proportion of alumina hydrate and/or silicate minerals that may be present in gibbsite-kaolinite-type bauxite. The diagram, with accompanying interpretations and use formulas, will be useful to those connected with the mining and processing of bauxite.

Jan 1, 1955

Geological Parameters Controlling the Improvement of Manufactured Sand Using Vertical Shaft Impact Crushers Instead of Cone Crushers Natural sand is a limited resource. In Sweden the total use of natural sand and gravel is around 20 million tonnes per year and the goal is to halve the use of this resource in the near future. Most of this natural sand is used for concrete production, so the consequence of this goal is that more and more concrete must be produced with manufactured sand. The bedrock of Sweden consists mainly of granites and gneisses, rock types mainly composed of various amounts of quartz, feldspar and mica. Manufactured sand from these materials generally contains rather flaky and elongated grains, and there are few types of granite that can be used as manufactured sand in concrete without increasing the amount of cement by eight to ten per cent. A Vertical Shaft Impact crusher (VSI) is commonly used to improve the shape of coarse aggregate particles. Research has shown that it is even possible to improve the shape in aggregate fractions less than 1 mm for some rock types. The aim of this project was to investigate which geological parameters control the improvement of manufactured sand when using VSI-crushers instead of the traditionally used cone crusher. In order to do this eight rock types of granitic composition were investigated. The selection of rock materials for the tests was based on grain size and mica content. A 4 - 8 mm fraction of each material was used for the tests. The characterisation of the shape of the material was performed using image analysis applied on microscopic images. The results showed that the VSI-crusher had improved the shape of all materials down to 0.036 mm, except for one rock sample. According to these results granites with low mica content and relatively high content of feldspars have the best prerequisites to produce manufactured sand for concrete with suitable geometric characteristics, and if these materials are crushed with a VSI crusher they almost show the same characteristics as natural sand.

Sep 13, 2010

As part of the Australian Mineral Industries Research Association (AMIRA) P9 project, methods of characterising both the ore and the machines in flotation circuits have matured considerably over the past 15 years. Machine characteristics include gas dispersion measurements, such as bubble size, gas hold-up and superficial gas velocity. Ores can be characterised in terms of floatability parameters on a size and mineral basis. Measurements have been performed on various copper plants in many countries around the world over the last 5 years. This paper outlines the cell and ore floatability characteristics of each copper plant and provides a discussion on the differences between these plants. In general, most porphyry copper ore bodies are processed at high tonnage through several parallel banks of cells at each stage of flotation. The floatability parameters of these copper ores are very similar in terms of rate of flotation and proportion of fast, slow and non-floating material. The cell characteristics are also similar, with superficial gas velocity, bubble sizes, and gas hold-up values being of similar magnitude. Investigation of the similarities and differences of the modem copper flotation circuits has allowed an increase in understanding of the particularities of copper flotation. Comparison against other copper circuits provides a benchmark and opportunities for future optimisation.

Jan 1, 2007

By F. Calizaya

The PT Freeport Indonesia‘s Deep Ore Zone(DOZ) copper deposit is located in the province of Irian-Jaya, Indonesia. Currently, a block cave mine is being developed around this deposit. Production is scheduled to start in year 2000 and to ramp up to25,000 tpd by year 2003. The air quantity requirement for this mine is equal to 780 m3/s. To supply this quantity, the mine will require five centrifugal fans (one 450 and four 750 kW fans). This study summarizes the technical aspects related to the installation and commissioning of one of these fans. The fan was installed on the surface in a parallel arrangement with two others. It has a design capacity of 240 m3/s of air at 2.2 kPa of static pressure. The study presents the installation details from the underground shaft excavation and portal development through fan testing and commissioning. It also presents the results of a monitoring system that was installed to determine the fan duties.

Jan 1, 2000

By J. R. Donald

For processing copper, continuous converting has been successfully employed in a variety of locations, but for nickel, there has yet to be a successful commercial implementation of continuous converting technology. At Inco?s Copper Cliff smelter, there are specific requirements for the production of Bessemer matte relating to downstream processing that makes continuous converting for nickel mattes even more challenging. The nickel carbonyl refineries require very low iron levels in the matte, and the sulphur deficiency must be carefully controlled such that the appropriate quantity of PGM-rich metallics are produced from matte separation. The present paper outlines continuous converter technologies that have been implemented in copper, and evaluates their potential for nickel converting. The challenges of producing a Bessemer matte to the required specifications are discussed. The economic and environmental driving forces, and the challenges of justifying a novel technology in place of productive existing equipment, are discussed.

Jan 1, 2005

Jan 1, 1995

By Ramón Alanís, Filiberto Orrante, Andrea Festa, Baldomero Gutiérrez, Fernando Cornejo

"SGS implemented two rules-based fuzzy logic expert applications on two grinding circuits operated by Peñoles Group in Mexico. Both expert systems are based on control strategies that push against process constraints to improve throughput. Based on proven methodologies, the projects also required some new approaches that led to permanent changes to the mill control strategy.This paper provides descriptions of the implementation, operation and performance of both expert systems. It also reviews how improved production rates were achieved through the use of a common set of expert technology tools. An overview of the resulting control strategies implemented on the two circuits is presented. The paper also discusses the identification of the process constraints within each circuit and how these constraints are used within the expert systems.INTRODUCTIONMexico-based mining company Peñoles Group and the Advanced Systems group at SGS, formally known as MinnovEX Technologies Inc., collaborated on the implementation of two expert systems in two grinding plants, both located in Northern Mexico.The primary objective of the expert systems was to increase throughput whilst still maintaining the cyclone overflow product size within an acceptable range. The secondary objective was to achieve a high level of utilisation of the expert technology.In order to achieve these objectives, SGS proposed a proven methodology which leveraged the existing operating and technical expertise at site through the client’s involvement in the design and implementation stages. The in-house operating and technical expertise of SGS was also brought to the project and implemented with the client’s approval at all stages. At both sites the final acceptance was defined upon meeting both process and utilization parameters.The development and deployment of rules-based fuzzy logic applications has matured as a technology and consequently, clear definition of process states and their place in the logic structure to control a given circuit are now transferable. The key to the robustness of the control logic depends on selection and tuning rules for maintaining stability and optimizing a given circuit. Application integrators need to have a standardized approach for timely integration and deployment; a critical component to avoid the common critiques that expert applications are idiosyncratic and difficult to maintain."

Jan 1, 2009

By X. Zhu, R. Du Plessis, J. D. Miller, D. G. Kotylar

Research on the low-potential hydrophobic state of pyrite with potassium amyl xanthate (PAX) as collector, is reported to help explain and understand the fundamental aspects of the N2TEC flotation process, which was originally developed for the improved recovery of gold from refractory auriferous sulfide ores. Typically in the N2TEC process, air is replaced by nitrogen as the flotation gas, and potassium amyl xanthate is used as collector for the reactive auriferous pyrite particles. The first N2TEC flotation process was commissioned at Lone Tree in Nevada in March 1997 and has been in operation ever since. On the basis of electrochemically controlled contact angle measurements, the low-potential, low-pH hydrophobic state of pyrite has been examined as a function of flotation variables such as pH, gas-phase composition, collector concentration and pyrite potential.

Jan 1, 2000

I report results of over 850 microprobe analyses of sulfides, sulfosalts and electrum from the Favona adularia-sericite epithermal deposit of the Waihi district in the southern Hauraki Goldfield of New Zealand. Pyrite and marcasite from altered wall rocks that enclose the veins are stoichiometric, with compositions of FeS2, and no significant trace elements. In contrast, pyrite in veins commonly contains appreciable As (up to 3.2 wt per cent), and locally contains several tenths of a percent of Cu, Zn, Co, Ag and Sb. Vein pyrite may contain up to 0.22 per cent Au, but Au contents do not show a positive correlation with As. Limited electrum data indicate that it ranges from Ag0.47 Au0.53 to Ag0.54Au0.41Cu0.01Zn0.04. Chalcopyrite is stoichiometric CuFeS2, and most galena is PbS, but some galena contains up to 4.4 wt per cent Se, which substitutes for S in its lattice. The galena is not argentiferous; the highest Ag content is 0.45 wt per cent Ag. Sphalerite averages 4 mol per cent FeS, but ranges up to 15 mol per cent. Tetrahedrites [(Cu,Ag)10(Zn,Fe)2(As,Sb)4S13] show variable substitution, but most are Cu- Zn- and Sb-rich. Veins also contain aguilarite (Ag4SeS), stromeyerite (CuAgS), naumannite (Ag2Se), and mckinstryite [(Ag,Cu)2S].

Jan 1, 2004

By H. Tomlinson

Fatalities from falls of roof and coal are responsible for the death Of more than 1,000 miners annually in the bituminous coal mines of the United States, or practically one-half of the total fatalities In and about these mines. The men are killed by falls singly or in small groups and little or no publicity is given these accidents as they lack the spectacular features of gas and dust explosions. As a result, the public and even the miners have the impression that accidents from falls of roof and coal are just one of the unavoidable hazards of the coal-mining industry. This belief is not true. Accidents caused by falls can be avoided largely by the application of sound engineering principles, by education, and by proper leadership in the industry, just as gas and dust explosions and accidents caused by explosives have been reduced in recent years. The necessity for studying falls of roof and coal becomes apparent by referring to the following data from a table by Adams and Chenoweth:3

Jan 1, 1933