Search Documents

By Peter Grandone

"INTRODUCTION The injection of water into partly depleted-oil-bearing formations as a means of supplying additional energy to flow oil wells now is recognized by the petroleum industry as an effective method of increasing the recovery of oil. The benefits to be derived from water-flooding oil sands were discovered accidentally more than 4o years ago, when oil producers in the Pennsylvania and western New York fields observed suustantial increases, in oil-production rates when water leaked past corroded casings of old wells into producing sands. This observation prompted some operators purposely to perforate or slit the casings opposite the producing formation in some of their wells to permit water to enter the formation. However, as many operators viewed the practice with skepticism and considered it to be in violation of oil-conservation principles,- systematic water-flooding was not initiated until the Pennsylvania legislature, in 1921, enacted a law authorizing water-flooding of oil sands in that State.Although water-flooding has been practiced in a haphazard manner for more than 25 years in Chautauqua and Montgomery Counties, Kansas, planned or systematic water-flooding in that State had its inception in 1935, when the legislature, following the example of Pennsylvania, also passed a lava/ authorizing water-flooding. The early operations and, to some extent, those still, practiced in the Chautauqua-Montgomery area consisted in raising or perforating the casing to allow water from upper strata to gravitate into underlying oil-producing formations. The extent to which this type of water-flooding affected petroleum production in the old stripper area of eastern Kansas is not known, but it is known to have increased oil production ap¬preciably from many leases.Following enactment of the law permitting water-flooding in Kansas, three operators inaugurated, in that same year, three organized flooding projects in three different counties of the southeastern part of the State. The first organized project on record was that of the York State Oil Co. in the Seeley pool, Greenwood County. On this project, the injection was started on May 15, 1935, into the Bartlesville sandstone at a top depth of 1940 feet."

Jul 1, 1944

By T. Gerritsen, R. C. Delgado, J. Janzen, E. R. Veloza

The paper describes the components of an Integrated Furnace Control system for covered-arc (shielded arc) smelting with results from the recently started 75 MW Cerro Matoso Line 2 Furnace. The paper starts with a review of the mechanisms of power and feed input and heat losses in the shielded-arc smelting process, and describes how the details of the control system are tailored to the process. The control modules of a covered-arc smelting furnace are described including measured results and screen captures. This paper focuses on Integrated Furnace Controls tailored to shielded-arc smelting, but similar approaches have been recently applied to other furnace processes including immersed-arc smelting.

Jan 1, 2004

Removal of As(III) and As(V) in Aqueous Solution There are toxic arsenical species such as As(III) and As(V), and arsenious species have specially strong toxicity. The strong toxicity causes contamination of groundwater and water pollution for the semiconductor production process. This study is concerned with the removal of As(III) and As(V) with various kinds of Mg/Al layered double hydroxides (LDH) containing CO32-, SO42-, Cl- and NO3- as interlayer anionic species. The anion exchange property is different from the kind of layered double hydroxides and the Mg-Al-NO3-LDH is superior in the anion exchange property of As(III) and As(V) due to the nature of nitrate ion existing in the interlayer. The pH condition suitable for As(V) removal is 7.1 or more. If the initial conditions such as 10mg/dm3 of As(V) concentration, 7.1 of pH, 1 m3 of amount of solution and 99 per cent of removal are fixed, the required amount of Mg-Al-NO3-LDH is 0.27kg for two step-batch operations. The As(III) is suitable to oxidize to As(V) before the removal processing.

Sep 13, 2010

By Jack Parker

Critical width Before we go further into pillar design, we should look into the matter of "critical width," because of its effect on pillar behavior. Critical width refers to the greatest width that the rocks above the mine can span before failure or, if there are pillars, the width to which we must mine before the pillars accept the full weight of the overlying materials. There are theories to help calculate that probable width, and they usually boil down to one-quarter or one-third of the depth of cover; but they don't always fit, and it would be better for us to understand the factors that control local conditions. Critical width may be controlled by the thickness or strength of one or more of the strata above the mining horizon. In a gold mine, we might have a thick granite or basalt above us, perhaps capable of bridging across most or even all of a small ore body. In that case, pillars might have to support nothing, or perhaps just the weaker or damaged rock below the strong main roof. Obviously it would be wrong to design for tributary load on pillars based on some lab-determined rock strength. In some coal mining districts in Utah, huge steps can be seen in the mountain sides, with slopes on weathered shales and vertical cliffs 100 or 200 ft high in thick, hard sandstones. The sandstones are capable of bridging across hundreds of feet, often making mining deceptively easy at first, but it becomes more difficult as greater areas are opened. Sometimes such a mining sequence leads to violent bumps and bursts as the wide spans of sandstone sag and bear down on the working faces, like giant nutcrackers, or as bridges eventually fail, releasing much pent-up energy.

Jan 1, 1993

By J. C. Marchand, M. A. Berube

"L'objectif principal recherché lors du broyage d 'un minerai est de libérer adéquatement ses valeurs utiles en vue de leur concentration ultérieure. La pratique courante consiste à tenter d'obtenir un produit de broyage d'une granulométrie constante. Malheureusement, les propriétés texturales des minéraux utiles varient naturellement dans un gisement et une telle stratégie n'entraine pas toujours pour ces minéraux un degré de libération constant. Pour un rendement optimal du procédé de concentration, cette variable très importante doit donc être périodiquement vérifiée.Jusqu'à maintenant, la plupart des études de libération des minerais se font en examinant des sections polies de particules du minerai broyé. Le GRAAIM a récemment assemblé un système modulaire d'analyse d'images qui servira en grande partie à des mesures automatiques du degré de libération des minéraux. Le système s'avère relativement peu coûteux comparativement à la plupart des analyseurs de texture conventionnels si l'on considère que plusieurs de ses composantes, par exemple le miniordinateur, sont utilisées à une foule d'autres applications, et il permet de plus une grande souplesse d'utilisation puisque l'on a qu'à construire des algorithmes de mesure et de calcul en fonction de l'objectif recherché. Des programmes particuliers permettant des études automatiques de libération sur des sections polies de particules ont ainsi été élaborés. Ils permettent également des mesures de teneurs et de distributions granulométriques apparentes des particules. Des résultats obtenus dans le cas de minerais de fer sont brièvement présentés afin d'illustrer la technique."

Jan 1, 1983

By G. C. Presley

Estimated domestic production of pumice and pumicite in 2004 increased about 23 percent since 2003, according to the U. S. Geological Survey (USGS). The USGS estimate of domestic production of 687 kt(757,000 st) for 2003 turned out to be 870 kt (959,000 st)of actual production. The USGS estimated the value of pumice and pumicite sold or used in the United States to be $26 million in 2004, up $4 million from the value in 2003. There was an estimated decrease in the mine, or mill, average price to $24.14/t ($21.90/st) in 2004 from $25.19/t ($22.85/st) in2003.

Jan 1, 2005

This article updates the status of fatalities occurring in both coal and metal/nonmetal mines from January through December of 2001. Based on preliminary accident reports, as of December 31, 2001, seventy-two fatalities have occurred at coal and metal/ nonmetal mining operations. During this period, forty-two fatalities occurred at coal operations and thirty fatalities occurred at metal/nonmetal operations. Ignition or explosion of gas or dust and fall of roof were the most frequent accident classifications in coal and powered haulage fatalities were the most frequent accident classification in metal/nonmetal.

Jan 1, 2002

By Ware AR, Doyle BJ, Hoogvliet H

The Ladolam deposit lies within the altered volcanic rocks of the caldera floor, part of which now forms Luise Harbour. It was discovered in 1982 in the course of a reconnaissance drainage sediment sampling programme. This was designed to follow up indications of surface hydrothermal activity noted by Government geologists during an earlier survey of the Tabar-Feni island chain. Diamond drilling began in September 1983 and by the end of 1989 a payable and proved mineable reserve containing 19 million ounces of gold had been established. Rock types and structures are masked at the surface by intense alteration and weathering. An extensive drilling programme has enabled the identification of these features and the relationships between them necessary for an understanding of the factors controlling gold mineralisation. It has also led to the recognition of two distinct phases of alteration. The first phase of porphyry-style potassic alteration was followed by violent caldera formation, producing extensive brecciation and veining. The second alteration phase partly over- printed the first phase and was an epithermal one, evidenced by argillic, advanced argillic and phyllic assemblages. During this event, a large volume of fluids circulated under the favourable structural conditions; these fluids included a sulphur- rich, neutral chloride brine believed to have transported the gold. Boiling and mixing of circulating fluids in the open breccias is thought to have resulted in deposition of the gold. There is evidence that this process is continuing at the present day.

Jan 1, 1991

[COUNCIL FOR 1991/92 President R.D. Beck President Elect JP. Hoffman Vice Presidents Senior Junior Dr H. Scott-Russell J.A. Cruise Immediate Past President Honorary Treasurer H.G. Mosenthal J.A. Cruise Members of Council Dr N.A. Barcza G.A. Brown B.R. Broekman Prof. RJ. Dippenaar B.R. Fleetwood* J.S. Freer P.R. Janisch P.J. Knottenbelt Dr J. Lurie R.P. Mohring *Co-opted K.C. Owen P.D.K. Robinson D.A.J. Ross-Watt P. Smith K.A. van Gessel DJ. van Niekerk P. van Schaardenburgh* CJ.C.J. van Vuuren* P.M.T. White]

Jan 1, 1992

The history of soft and hard rock underground mining is blemished with regional instabilities of mine workings. Whilst the potential consequences of regional instability events are recognised to be high, there is a false perception that the probability of them occurring is very low. In fact, Australia has averaged more than one event per year for the past 20 years. At least five fatalities and over $100 million of losses have been associated with the events. As such, they are a core risk to underground mining and have a significant effect on the quadruple bottom line of business û safety, environment, community acceptance and economics. This paper explores the important roles that risk management has in reducing the probability and consequences of regional instabilities. It concludes that education and continuing professional development are essential elements for effectively managing the risk.

Jan 1, 2003

By C M. Wawryk, S L. Garwin, J D. Foden

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The Batu Hijau porphyry Cu-Au deposit in south-western Sumbawa, Indonesia is an ideal natural laboratory to study the fractionation of iron isotopes in magmatic rocks that range in composition from basaltic andesite to tonalite. Intrusive rocks are associated with a porphyry system that contains well-preserved early hypogene copper mineralisation. We analysed pre-, syn- and post-mineralisation igneous intrusive rocks. We also separated magnetite, chalcopyrite and bornite from hypogene porphyry-style quartz veins, and measured the Fe-isotope ratios of samples by solution multi-collector ICP-MS. Iron isotopic composition of samples from the magmatic suite show an increasing d57Fe with increasing SiO2, supporting geochemical and textural evidence that the Batu Hijau Tonalites underwent closed system fractionation. Equilibrium and co-existing mineral textures allow the calculation of the following preliminary empirical mineral-mineral fractionation factors at 500°C for certain mineral pairs.Iron isotopes have the potential to provide geothermometric data to complement fluid inclusion data, especially where heating stages have operational limitations and where fluid boiling results in a wide variety of inclusion types that may make analysis difficult.CITATION:Wawryk, C M, Foden, J D and Garwin, S L, 2015. Iron isotope fractionation in magmatic-hydrothermal minerals – a porphyry copper case study from the Batu Hijau deposit, Sumbawa, Indonesia, in Proceedings PACRIM 2015 Congress, pp 389–396 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By Robert G. Bottge

The Bureau of Mines investigated the availability of the land in south-central Alaska for exploration and mineral development of locatable minerals under State or Federal laws. The land ownership for an area of nearly 72.5 million acres in south-central Alaska was divided into 3 availability categories and 15 subcategories. In July 1985, 31.0 million acres of the study area were available for mineral exploration and development, 6.2 million acres were available with restrictions, and 35.3 million acres were unavailable. About 23.6 million acres in the study area are underlain by mineral terranes. About 9.9 million of the 23.6 million acres are available for mineral entry, 2.4 million acres are available with restrictions, and 11.3 million acres are unavailable. While much of the land currently classified as unavailable will be reclassified once it is conveyed to the State or to Native corporations, about 22% of the unavailable lands underlain by mineral terranes are now Federal parks, preserves, wildlife refuges, wild and scenic rivers, and military lands, all of which are considered permanently unavailable for mineral exploration and development.

Jan 1, 1986

By L. D. van Dyk

The extraction of iron and lead from their oxides with a volatile organic ligand such as acetylacetone in the gas phase offers potential advantages of lower energy consumption, recycling of the extractant, recovery of pure metals, and a reduced environmental impact compared with conventional extraction processes. The influence of reaction temperature, ligand flow rate, and metal oxide levels on the extraction and rates of reaction of iron and lead from single metal oxide (synthetic haematite (Fe2O3) and synthetic massicot (PbO)) systems in a fluidized bed was studied. It was found that at the investigated acetylacetone flow rates, the influence of mass transfer was limited, but that the reaction suffered from reactant starvation. When the metal load increased the effect of starvation on the rate of reaction also increased. The reaction kinetics increased with an increase in temperature for both systems. At low metal oxide concentrations more that 80 per cent of the iron and lead could be extracted from their respective metal oxides after only four hours.

Jan 1, 2012

Current mine production planning, scheduling, and allocation of resources are based on mathematical programming models. In practice, the optimized solution cannot be attained without examining all possible combinations and permutations of the extraction sequence. Operations research methods have limited applications in large-scale surface mining operations because the number of variables becomes too large. The primary objective of this study is to develop and implement a hybrid simulation framework for the open pit scheduling problem. The paper investigates the dynamics of open pit geometry and the subsequent material movement as a continuous system described by time-dependent differential equations. The continuous open pit simulator (COPS) implemented in MATLAB, based on modified elliptical frustum is used to model the evolution of open pit geometry in time and space. Discrete open pit simulator (DOPS) mimics the periodic expansion of the open pit layouts. Function approximation of the discrete simulated push-backs provides the means to convert the set of partial differential equations (PDEs), capturing the dynamics of open pit layouts, to a system of ordinary differential equations (ODEs). Numerical integration with the Runge-Kutta scheme yields the trajectory of the pit geometry over time with the respective volume of materials and the net present value (NPV) of the mining operation. A case study of an iron ore mine with 114 000 blocks was carried out to verify and validate the model. The optimized pit limit was designed using Lerchs-Grossman?s algorithm. The best-case annual schedule, generated by the shells node in Whittle Four-X yielded an NPV of $449 million over a 21-year mine life at a discount rate of 10% per annum. DOPS best scenario out of 2 500 simulation iterations resulted in an NPV of $443 million and COPS yielded an NPV of $440 million over the same time span. The hybrid simulation model is the basis for future research using reinforcement learning based on goal-directed intelligent agents.

Jan 1, 2008

By Monika Patrycja Polak - Micewicz

This paper presents an approach for estimating the fatigue life for the base of powered roof supports (shield) manufactured by the FAZOS roof support company. FAZOS?s powered roof supports are designed to operate on an inclined coal seam in full caving with a medium, strong roof strength. This shield support is utilized in conjunction with a shearer and face conveyor for a complete longwall mining system. To design shield support, it is essential for contractor to know the physical (hardness, toughness, etc.) and mechanical properties of material (tensile strength, Young?s modulus, etc.) used for the shield support as well as the geotechnical properties of the mine site. The fatigue strength of the shield support material depends on the mean stress, alternating stress, cycle frequency, transport dimensions, mine environment and other factors. In order to estimate the fatigue life for a powered roof support system, it is assumed in this paper that the support must keep the roof stable in the mine under variable load cycles. The approach selected in this study contains Goodman?s model (Goodman, 1899) for all blocks in the design housing which is subjected to sinusoidal load. On this basis, the degree of fatigue damage was calculated and compared to the results of experimental tests. It will be shown that there is a significant detrimental effect on the fatigue life of the base of the powered roof supports due to geometrical notches. The Ramberg-Osgood model and damage accumulation rule (Palmgren-Miner) (Miner M., 1945) were used and numerical analyses were conducted, utilizing ANSYS finite element software. These analyses play a very important role in longwall casing design. The proposed method allows assessment of the yield state and forecast of the structure cracking, taking plastic strains occurrence into account. The presented method is universal and can be applied for fatigue life estimation of other subassemblies of powered roof supports. The final portion of the paper presents results of variable amplitude loading simulations on the S355N and S690Q steel used to make powered roof supports. The results of the physical tests were compared with the results from finite element methods. The proposed approach to calculate fatigue life gives the best correlation between the experimental results and calculated values of fatigue life for the powered roof support base. Finally, the design process uses a simple approach to predict fatigue life in a short time, reducing design costs and providing longer service life for roof supports.

Jan 1, 2012

By Bruce F. Grant

This report discusses research being done by the Petroleum and Natural Gas Branch und the Applied Physics Branch of the Bureau of Mines to deter-mine the most effective uses of explosives in shooting oil and gas wells, as measured in terms of rates of production from the wells. An experimental investigation of the effects of detonating explosives in shallow holes drilled in rocks, chosen to be similar to those forming oil and gas reservoirs, forms the basis of this study. Records obtained from strain gages placed in the rock around the experimental shots permit determination of the generation and propagation characteristics of the strain wave. Water-injection tests made on the test holes before and after shooting allow the increase in fluid conductivity resulting from the shot to be determined. By rotating these data to the physical properties of the rock, and by conducting shooting experiments over the range of rock types common to oil and gas reservoirs, it is expected that relationships between the fluid conductivity and the properties of the explosive and rock can be developed and used for designing efficient shots for oil and gas wells. Four series of experiment.al tests were completed during the summer of 1949 and are described herein. The results of these tests confirmed the feasibility of the experimental approach and permitted outlining the plans for future research discussed in this report. This report is presented to acquaint industry with this research program and the progress to date, so that the Bureau may have the benefit of suggestions from interested readers.

Jan 1, 1950

By D. P. Roberts

This investigation aimed to simulate the experiments performed by Nic Gay (Gay, N.C. 1976. Fracture growth around openings in large blocks of rock subjected to uniaxial and biaxial compression. International Journal of Rock Mechanics and Minining Sciences and Geomechical Abstracts, vol. 13. pp. 231-243) on fracture growth around openings in blocks of rock subjected to uniaxial and biaxial compression, using the Elfen discrete element code. The results of the physical experiments indicated a number of trends that were successfully replicated in the numerical simulations, including crushing ahead of the face, the formation of a sub-vertical tensile fracture at centre-span, the formation of groups of fractures originating from the crushed face zone, the formation of large corner-to-corner fractures which precede sample failure, and linking of slot corner and sample corner fractures leading to sample failure. In addition, other features were apparent that were not reported by Gay. It is believed that these took the form of conjugate shear fractures (as reported by Gay in a previous paper) and other features that may have been altered or inhibited by the presence of pre-existing structure in the physical samples. It was found that the samples, though nominally made up of the same rock type, must have had significantly differing properties. The presence of pre-existing structures may have contributed to this discrepancy. Strain measurements from the physical experiments were reasonably well matched, except where the gauge lay directly in the path of advancing fractures.

Jan 1, 2012

By N. D. L. Burger

An effective prototype face support system to minimize rockfalls in rockfall-prone mines was developed and patented during a project sponsored by the Mine Health and Safety Council (MHSC). An experimental development model (XDM) roof support unit was developed and evaluated. Mines with rockfall problems in the face areas can use the roof support system to reduce fatalities and injuries in the face area of stopes. The roof support system consists of two similar support units connected to each other via two crank mechanisms. Each unit consists of a headboard supported by a ?wishbone? structure (top and bottom leg). In the first design a threaded bar with struts similar to a scissors jack keeps the legs apart. (In the final version that was field trialed, the threaded bar mechanism was replaced with a hydraulic cylinder). All the components are manufactured from steel. To move the system forward the first support unit is collapsed, the second remaining in the loaded position. The first unit then hangs from the second unit to which it is connected. The first collapsed unit is then manually cranked forward and prestressed. If the required position is still not achieved, the other unit is released and moved forward. The specification for the system was determined and presented at a workshop with industry participants. Different concepts were developed and evaluated against the system specifications. A technology demonstrator was then developed and tested on surface. The technology demonstrator development process included detail design, building and testing of components and subsystems, design reviews and the building and commissioning of the technology demonstrator. The testing of the technology demonstrator was done in a 500-ton hydraulic press, in a mock-up stope and underground. A risk analysis, in which technical, logistical and economic aspects were assessed, was done to determine the critical areas of the system. During the next phase of the project working prototypes were developed for underground tests and evaluation. This process indicated that it was necessary to adjust the system specifications and a redesign was called for. In an iterative process test units were built for purposes of evaluation, specification verification and field trialing. After the successful conclusion of the trials the equipping of a complete production stope started for purposes of integrating the system into the current mining process.

Jan 1, 2008

By Daniel Hauer

Blocking. (5) The “blocking” of boulders is a much cheaper way of breaking them up than “mud capping.” It should always be used in preference to that method except when too much time will be consumed by a crew of men waiting for the drilling to be done, as shown in example of cost No. 1, as given under “mud capping.” Under such circumstances the time consumed would be a greater cost to the contractor than the extra amount of dynamite. Then, too, on large thin boulders to drill one hole would result only in breaking the stone into such pieces as would again have to be broken; and the many holes might equal the cost of extra dynamite. Under such circumstances if method (6) cannot be used, “mud capping” will have to be resorted to, to do the work economically.

Jan 1, 2006

By Eric R. Bauer

The U.S. Bureau of Mines, in cooperation with a southwestern Pennsylvania coal mining company, BethEnergy Inc., Mine No. 60, Eighty-Four, PA, recently assessed the feasibility of using pre driven recovery rooms (open entry recovery) when longwall mining to increase the productivity of the coal extraction process. Two recovery entries, one 200 ft long and another 600 ft long, were supplementally supported with bolts, channels, and wire mesh, and either fly ash-cement piers or fiber cribs, then mined into by the longwall face. The recovery entries showed little deterioration as the supports provided adequate resistance to the front abutment loading. Compared with conventional recovery methods, the fullface recovery room allowed for panel extraction to be completed nearly 17 days faster and to reduce face equipment move time by 1-1/2 days. The potential productivity increase accompanying recovery rooms is greater than the cost of supporting a fullface recovery room. The fullface recovery room provided over 18 additional production days and the opportunity to mine nearly 68,400 st of coal per year per panel mined.

Jan 1, 1989