Search Documents

By M. W. Grabinsky

Better in situ performance data is required in order to advance the rational geomechanical design of cemented paste backfill systems. A few in situ test programs have been conducted, but these have suffered from too few measurement locations within the stope and have not used enough different types of transducers to fully capture the information of significance. In this paper the important geomechanical design aspects are listed, the underlying physical phenomena are described, and some previous in situ measurement efforts are reviewed. A new approach to in situ measurement campaigns is then described including measurement techniques, locations, and the logistical aspects of mobilizing transducers in an active mining environment. A work-in-progress is used to illustrate the principles and concepts involved.

May 1, 2007

By Yuexin Han, Wenbo Li, Xinran Zhu, Pengchao Li

A multi-stage fluidization magnetization roasting is a promising method to treat limonite ore. The dehydroxylation of limonite ore is a key reaction in the pre-heating stage. In this study, the dehydroxylation mechanism of limonite was studied in a laboratory fluidization roasting reactor. The samples were characterized using in situ X-ray diffraction, Fourier transform infrared spectroscopy, and simultaneous thermogravimetry and differential scanning calorimetry analysis. The phase transformation and kinetics analysis were studied. Results indicated that the dehydroxylation occurred at the temperature of 250–350 °C with the vanish of hydroxyl functional groups (-OH). The dehydroxylation kinetics followed the 2-D diffusion (Jander) reaction model G(α) = [1 − (1 − α)1/2]2, and the calculated activation energy was 113.43 kJ·mol−1. This study is conducive to exploiting limonite ore resources using magnetization roasting technology.

Nov 2, 2023

By Jay J. Burns

TWO zinc concentrating mills are operated by the St. Joseph Lead Co. in St. Lawrence County, N. Y. The Edwards mill is operating at present only sixteen hours a day treating 400 tons daily. The metallurgy at Edwards presents no unusual problems therefore this discussion is mainly limited to the metallurgy of the Balmat ore. The Balmat mill has a capacity of 1,250 tons per day and the operating crew consists of three shift bosses each with five millmen per shift. Two crusher operators work on each of two shifts and one cleanup man on day shift. The repair crew is made up of a foreman and three repairmen, one of the repairmen being capable of taking over any operating job in the mill from shift boss down. Each millman is capable of handling the next job in line and several men in the yard crew are broken into handling the start-off job in the mill so that temporary shortages of men do not cause extensive overtime. Sphalerite, pyrite, and galena, the principal ore minerals, occur in a gangue of calcite, dolomite, and silicates, especially diopside, plus tremo-

Jan 1, 1947

By T. Z. Mugodi, D. R. Fleming

Information and Communications Technology (ICT) is defined as ‘The goods and services that support the electronic display, processing, storage and transmission of information’. Early in 2002 the South African Department of Trade and Industry (DTI) commissioned a study into the diffusion and adoption of ICT in eight sectors of the economy. The platinum mining Sector was one of these. The key findings presented in this paper are based on the platinum sector component of that study. The paper examines the theoretical basis behind technology transfer and innovation diffusion and presents the results of an ICT diffusion survey carried out in the South African platinum mining sector. ICT is shown as the modern day technological tool which is an accelerator of economic development. The current state of ICT diffusion in the platinum mining sector is defined and projections for the near future are given. Recommendations which will ensure smooth and full adoption are presented and justified.

Jan 1, 2003

By K. A. Grace

K.A. Grace's article advocates usage of the terms describing resources as defined by the US Bureau of Mines (USBM) and the US Geological Survey (USGS). Originally recommended in 1943, the terms were revised in 1976 and again in 1980. Mr. Grace further recommends that the term reserves should be severely restricted and that it should encompass mining and processing factors. The list of references quoted in the article does not, however, mention the study concerning reserves that was made over a period of almost four years by a joint Committee on Definitions. This committee was sponsored by three societies - the American Institute of Mining, Metallurgical, and Petroleum Engineers (AIME), the Society of Economic Geologists (SEG), and the American Institute of Professional Geologists (AIPG). Most of the detailed work was done by a working party appointed by the Society of Mining Engineers (SME) of AIME. After studying previous definitions in the US as well as in the United Kingdom, Canada, Australia, France, and other European countries, the following definitions were proposed and accepted in 1974 by the SME board of directors. (Ore reserve definitions in Rhodesia, South Africa, or New Zealand were not mentioned as having been reviewed.) Table 1 lists definitions from MINING ENGINEERING, July 1975. Notice in Table 1 it was mentioned, under Resources, that the definitions of reserves were recommended for the purposes of commercial evaluation. It was further stated that the terminology adopted by the USBM and the USGS, as released to the public, covering resources, was recognized as such. Mr. Grace also recommends that reserve calculations should allow for future losses in ore tonnage, ore grade, milling, and smelting. Unfortunately, it might take years to develop a prospect after it has been discovered. Mining methods have to be tested before being finalized in order to know what tonnage of ore is going to be lost, or how much dilution is likely to occur. The same problems are present in concentrating or in smelting. Operating mines usually know how mined grade compares with ore reserve grade. They can usually predict fairly closely what their final metal recoveries are probably going to be. It is, however, expecting too much to have to delay quoting reserves from say a recently drilled prospect. Any responsible mining geologist or mining engineer (or company for that matter) should state several things about an ore reserve calculation: that it is or is not a preliminary estimate only; that estimated grades have not been diluted to allow for a future, as yet unknown, mining method; that metal recoveries are or are not only tentative, based perhaps on drill hole samples only or on no metallurgical testing at all. Reserves of a partially explored prospect are always quoted when it becomes necessary to raise capital. If they are described as preliminary only (really just tonnage and grade estimates and not true "reserves") in addition to being accompanied by some of the items just mentioned, nobody is going to be misled. If, on the other hand, a report by a member of the SME or SEG is intentionally misleading, the individual must be reported and eventually disbarred from his or her society. To summarize, let us stay with the definitions of ore, ore reserves, and related terms as recommended and accepted by SME. I might add that on occasion I have used a fourth category in my ore reserve calculations, namely Geologically Possible Ore. This category is more or less the same as Inferred ore defined by the USBM and USGS. I have never given a grade to this category, which may be based only on geological mapping, geochemical sampling, or geophysical traversing.

Jan 8, 1985

By Haigh J. E

An accurate measure of the earth's magnetic field can be made in a few seconds with the portable proton precession magnetometer. Such an instrument increases the applicability of the long successful method of magnetic prospecting for minerals. As an example of the usefulness of the proton magnetometer, a survey over volcanic rocks near Apsley (Tas.) was made.INTRODUCTIONA completely portable magnetometer whose operation is based on the free precession of polarized protons in the earth's magnetic field, is now available on the market at a price competitive with magnetometers based on the classical physical principles. The ease, accuracy, rapidity, and reliability with which measurements of the earth's total magnetic field can be made with the proton precession magnetometer, led to the try-out of the instrument in an actual field problem so as to evaluate fully the capabilities of the instrument. Such evaluation is important, because the history of magnetic prospecting has shown that whenever significantly improved instrumentation has been introduced, prospecting costs have been substantially cut and many areas in which the prospecting costs were formerly considered excessive in relation to probable returns, have become economic mineral prospects. The proton precession magnetometer offers the possibility of opening up new areas for successful magnetic prospecting.AN OUTLINE OF THE HISTORY OF MAGNETIC PROSPECTINGWhile an outline of the history of magnetic prospecting is not directly connected with the evaluation of a proton pre...

Jan 1, 1963

By S. McPherson, M. Chalkley, R. Ellenwood, W. Nicot

"The Moa JV was formed in December 1994 as a 50/50 joint venture between Sherritt Inc. and General Nickel Company S.A. of Cuba. The joint venture consists of the mine and Pedro Sotto Alba processing plant in Moa, Cuba and the Corefco refinery in Fort Saskatchewan, Alberta, Canada. Throughout its now nearly 23-year history, the Moa Joint Venture has faced a number of global, operational and process challenges. Global challenges have included high input costs such as for fuel oil and sulphur, as well as low nickel prices. Operational and process challenges have included increasing ore haulage distances, decreasing ore Ni + Co grades, and increasing ore impurity contents. For example, increases in impurities such as Mg and SiO2 in the ore result in increasing acid demand in leaching and decreasing solids content of preheated leach feed slurry, respectively. In spite of these challenges, the mixed sulphide production capacity from the Moa Joint Venture has increased from 12,500 to 37,000 t/y Ni + Co since 1994 by judiciously targeting expansion projects and by continuously performing process and operational improvements.INTRODUCTION The Pedro Sotto Alba high pressure acid leach (HPAL) plant at Moa Bay, Cuba has a long history (Maslenitzkiy, 1969; Chalkley, 1996; Carlson, 1960; Roy, 1961; Carlson 1961). The plant was constructed by Moa Bay Mining Company and started up in late 1959 after several years of process development by Freeport Nickel Company, including operation of a 10 t/d plant in Hoskins Mound, Texas and a 50 t/d plant in Port Nickel, Louisiana (Southwick, 2004), as well as development work by Chemical Construction Company (Chemico) to precipitate metal sulphides (Roy, 1955a; Roy, 1955b). The Moa plant had an original reserve of 50,000,000 t of ore, graded at 1.35 wt% Ni, 0.146 wt% Co, 3.70 wt% Si, 1.00 wt% Mg and 4.5 wt% Al. At original design rates of 2,000 kt/y of ore, the design capacity of the plant was around 25,000 t/y Ni + Co as a mixed sulphide product, which would be shipped to the Port Nickel Refinery in Louisiana for processing. In 1960, the plant changed ownership and was restarted in 1961 under Cuban management. Between 1961 and 1989, the plant was also supported by involvement from the former USSR, supplying spare parts and consumables. In 1994, Sherritt Inc. partnered with the General Nickel Co. S.A. of Cuba and formed the Moa Joint Venture. This joint venture includes the mine and Pedro Sotto Alba HPAL processing plant in Cuba and the Corefco refinery in Fort Saskatchewan, Alberta, Canada. Under this partnership, ore is processed in Cuba to produce a nominally 55 wt% Ni and 5 wt% Co mixed sulphide product that is shipped to Canada and processed by Corefco to produce class 1 nickel, high grade cobalt and byproduct ammonium sulphate fertilizer."

Jan 1, 2017

By R. Shimpo

Equilibrium calculations by a computer may sometimes fail in giving solutions when the system includes a large number of components and more than three phases, and especially when no definite information about stable phases is given. An improved method of calculation is presented in which the number of phases need not to be initially fixed, phases can appear or disappear in the course of' calculation and a new method is combined with the Newton-Raphson method to obtain solutions easily. The improved method is applied to the copper smelting operation and all the successive stages of the operation are successfully simulated.

Jan 1, 1983

By John C. Nigro

Bench scale and pilot plant research was conducted using dolomites (CaO,MgO) lime as the basic additive in the preparation of self-fluxed pellets from a typical magnetic taconite concentrate (5.57 S_2). The specific objective of this investigation was to ascertain the viability of the magnesia lime pellets in high temperature oxidizing and reducing atmospheres. Pellet basicity and induration temperature were major parameters affecting fired pellet quality; temperatures ranging from 1,200° to 1,250" C appeared to be the most favorable for production of self-fluxed pellets with basesities (B) above 1.0. Comparison of the mechani¬cal and metallurgical properties of regular (acid) and self-fluxed pellets (B 1.55) produced under similar conditions in a modified grate pelletizing machine showed that the self-fluxed pellets were more resistant to abrasion and to high and low temperature reduction disintegration, an important consideration in commercial application. The Plus 3 mesh Linder index increased from 68 percent (regular pellets) to over 90 percent (self-fluxed pellets). The reducibility and swelling indices of the self-fluxed pellets were found to be comparable to the regular pellets.

Jan 1, 1972

By Jie-Liang Wang, Yongdan Cao, Zhao Cao

"The effect of ethylenediamine tetraacetic acid (EDTA) on flotation separation of fluorite from bastnaesite and its selectively depression mechanism on fluorite were studied by single mineral flotation, artificial mixed minerals flotation, solution chemistry analyses, Zeta potential and XPS measurements.The results show that fluorite can be deeply depressed by EDTA while the flotation of bastnaesite is almost unaffected when octanohydroxamic acid (OHA) is used as a collector. The separation index (SI) between bastnaesite and fluorite increases with the dosage of EDTA, SI can be raised from 1.18 to 12.66 when EDTA dosage increases from 0 to 2×10-3mol/L.Solution chemistry analyses show that EDTA is able to convert the Ca(OHA)2 hydrophobic precipitation on fluorite surface to a soluble Ca-EDTA complex but cannot complexly dissolve the Ce(OHA)3 precipitation on bastnaesite surface. Therefore, the Zeta potential of OHA conditioned fluorite can be reduced significantly by EDTA while the reduction degree to Zeta potential of bastnaesite is relatively low. XPS measurement shows that EDTA removes the chemically adsorbed OHA from fluorite surface but has little effect on the adsorbed OHA on bastnaesite surface. As a result, fluorite can be selectively depressed by EDTA in bastnaesite flotation, which behaves an important industrial application prospect in rare earth ore flotation.INTRODUCTIONNowadays, Rare earth elements (shortened as RE) and compounds are of significant importance for a range of rapidly expanding industrial applications including catalysis, metallurgy, renewable energy, and special materials due to their unique electrical, magnetic, optical and chemical properties [1]. The seventeen RE elements, including the lanthanide-group fifteen elements, yttrium and scandium, could be divided into three groups, i.e., light, medium and heavy RE elements based on the different solubility of RE sulfates [2]. Bastnaesite ((Ce,La)CO3), containing approximately 75% REO, is one of the most important light RE minerals [3]. Flotation is the common method to recover basetnaesite [4-6]. Nonetheless, basetnaesite is often associated with calcium-bearing gangue minerals such as fluorite, and the separation of basetnaesite and fluorite by flotation is usually difficult due to their similar surface properties and therefore floatability [7-9]. Therefore, research on high selective flotation reagents of bastnaesite over gangue minerals has attracted a lot of attention [10]."

Jan 1, 2018

By William Cochran

The Bureau of Mines investigated mine subsidence caused by recent underground mining, estimated the extent of damages, and formulated a procedure for evaluating subsidence costs. On the basis of the quantity of material removed from beneath the surface, bituminous coal mining currently causes more extensive subsidence problems than mining of other minerals; costs are highest in areas such as western Pennsylvania where urban and suburban development and related types of land use conflict with mineral recovery. The Bureau of Mines estimated subsidence costs, including surface damages and control costs, for a 12-county area in western Pennsylvania for 1968. Total surface damages attributable to the underground production of bituminous coal in the 1-year period were $295,000; in addition, 12.4 million tons of coal, valued at $4.3 million, was left in place to minimize potential surface damage. Of the total subsidence cost ($4.6 million), $2.7 million was classified as external or social costs, not reflected in the market value of bituminous coal; this averaged $0.05 per ton of production, or slightly less than 1 percent of the market value.

Jan 1, 1971

By Dale S. Preece, Lee M. Taylor

Accurate computer prediction of the muck pile produced by a conventional blast requires modeling of the physics that occurs during the rock motion phase of a blast. The ability to predict the motion and the subsequent muck pile can have a significant economic impact on the mining industry.

Jan 1, 1990

[E. E. SCHUMACHER, Chairman ARTHUR PHILLIPS, Past-Chairman L W. KEMPF, Senior Vice-Chairman E. A. ANDERSON, Vice-Chairman H. A. MALONEY, Treasurer FRANK T..SISCO. Secretary 29 West 39th Street, New York 18, N. Y.]

Jan 1, 1946

By Joseph J. Wallace

1. The investigation shows that there are two coal beds of major importance in Perry County from the standpoint of present production -Flag and Fire Clay -and two beds of minor importance -Haddix and Hindman. The Flag and Fire Clay beds contain the largest remaining known reserves. 2. Known measured and indicated reserves in all beds, based on a minimum thickness of 14 inches and 1,800 tons per acre-foot of coal in place, are estimated at 840 million short tons as of January 1, 1954. Of this total, 720 million short tons is in beds 28 inches and more thick. Areas in each bed were omitted from the estimate because available data relative to the bed characteristics are too meager for making an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, these should be added to the total estimated reserves.

Jan 1, 1954

By M. Fan, Z. Long

"This paper presents some studies on recovering valuable elements from Chinese coal by-products, including coal combustion fly ash, stone coal ash, and coal flotation tailings. Both commercialized technologies and economic potential recovery methods are described in this study. Magnetically stabilized air-dense medium fluidized bed separation, tribo-electrostatic separation, froth flotation, and hydrometallurgical methods are discussed in recovering various valuable elements in Chinese coal by-products from different coalfields. These valuable elements include iron, carbon, aluminum, rare earth elements, lithium, gallium, germanium, uranium, titanium, scandium, silicon, vanadium and phosphorus, etc. The ultimate goal is to fully utilize all valuable elements in coal by-product. Each component within coal by-product should be efficiently segregated to its highest value. INTRODUCTION Coal is mainly composed of energy-producing elements carbon and hydrogen. In addition to these elements, coal usually contains many other valuable elements, including iron, aluminum, silicon, rare earth elements, lithium, gallium, germanium, vanadium, uranium, titanium, scandium, and phosphorus, etc. These coal-associated elements are significantly enriched in coal combustion by-product fly ash because of majority of main components, carbon and hydrogen elements, being removed. Table 1 provides the chemical composition range of the main elements oxides in 12 Chinese fly ash samples collected from coal power plants located in Northeast China, Northwest China, Southwest China, and Southeast China. It can be seen from Table 1 that the major mineral components of different ashes are similar, but the bulk chemistry of different fly ashes may vary widely due to the changes of ratios of the mineral components in different coals. The major mineral components in various Chinese coal combustion fly ash are silicates, iron oxides, and unburned carbon."

Jan 1, 2017

By H. Kenworthy

The purpose of the study described in this publication is to develop methods for recovering simple master alloys or single metal components from discarded and scrapped S-816 alloy, The Bureau of Mines started this investigation late in 1955 after the need became apparent for a method of reclaiming high-temperature alloys from an ever-increasing accumulation of rejected and wornout jet engine turbine buckets. Laboratory studies showed the following: (1) Pyrometallurgical separations are not selective enough, (2) several methods can be used for effective chemical dissolution of the major constituents of the alloy, (3) a master alloy or complex salts of cobalt and nickel can be separated, (4) chromium, contaminated by several other metals, may be segregated, and (5) more time and effort need to be expended in separating the minor constituents and improving the purity of the major metals removed. Difficult and incomplete chemical separations were attributed to the complexity of alloy composition, as were the long tedious chemical analyses o' products. For determination of several of the metallic components, standard methods of separation and routine analytical procedures had to be considerably modified to achieve satisfactory results. The overall technical problems involved in separating S-816 components do not appear to be insurmountable; however, refinement of several of the methods used in this investigation is desirable.

Jan 1, 1961

By Bill Starke

The acceptance of AugerCast piles in Canada has been limited. Many engineers are apprehensive about the quality of the piles produced by this method. However, advances in the sensing instruments and computer technology can now provide satisfactory levels of quality assurance. Post construction tests such as the sonic echo method can give an indication of pile shaft integrity. Computerized monitoring of the pile installation process is an immediate and more positive method of quality assurance. The computer continuously measures and records the parameters which indicate the quality of the pile. If these parameters do not indicate a satisfactory pile, it is replaced before the concrete hardens. Computerized monitoring of the installation process is another tool available to the engineer. The data from this system analyzed with soil borings, site inspections, and possibly sonic tests can provide the engineer with enough information for pile certification.

Jan 1, 1997

How did you get into mining; were you from a mining town or mining family? Not at all. I grew up in northwest Kansas. I liked to hunt and fish, so I thought it would be fun to work for a company that made knives or guns. It seemed like metallurgical engineers would be something those companies could use, so I started in physical metallurgy. I got a summer job at the great Climax molybdenum mine near Leadville, CO shoveling muck onto conveyors. I was hooked. I loved everything about mining, so in the fall, I changed majors from physical metallurgy to mineral processing. For many years you actually discouraged young people from studying the mining disciplines. Could that be right? That’s true.

Jan 1, 2007

By J Canterford

There is an apparent push to develop and commercialise "new and innovative" process flow sheets. A not-too-difficult reality check clearly demonstrates that the success rate of this push is not particularly significant and in fact could be regarded as a waste or misappropriation of R&D funding and the associated brain power. As Julian Sumner Miller would comment "why is this so?" To put it bluntly, many of the so-called innovative developments are equivalent to gold plating the dunny door - visually interesting but of very limited practical value. This presentation encapsulates some personal lessons learnt over the past 45 years.CITATION:Canterford, J, 2013. Developing a ænew and innovativeÆ process flow sheet - Traps for all players of all ages, in Proceedings MetPlant 2013 , pp 1-5 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 15, 2013

It has been fairly firmly established (Fisher, N. H., 1945) that the fineness of the gold in any ore deposit varies with the depth from the surface at which the deposit was formed, and, as a corollary to this, that it is dependent upon the temperature and pressure at the time of deposition. This relationship is such that, under certain conditions, the gold fineness, taken into consideration with other recognised criteria, furnishes a very sensitive and reliable guide to the relative temperature of ore formation, at least within the epithermal and the upper part of the mesothermal range.Definition of Fineness.The fineness of gold is calculated in parts per thousand and refers to the proportion of gold present in the naturally occurring metal in the lode, which is actually a gold-silver alloy, containing usually about 10 parts per thousand of base metal and up to 500 parts perthousand of silver. A clear distinction should be made between fineness and gold-silver ratio. The latter refers to the total gold and silver in the lode as determined by assay and is usually expressed as the ratio Au:Ag. Only in deposits where other silver-bearingminerals are entirely absent, which occurs comparatively rarely, can the gold-silver ratio be used as a measure of gold fineness and, in many cases, the two have no relationship. For instance, in the Edie Creek area in New Guinea, the lodes formed under shallow epithermal conditions all carry gold 500 to 550 fine, although the gold-silver ratio ranges from 1:100 to 1:1, in places in adjacent lodes.Determination of Gold Fineness.The fineness of lode gold can be determined only after it has been separated from all other minerals. Amalgamation recovers gold fairly cleanly - unless native silver is present - and the fineness of amalgam bullion is generally a reliable indication of the correct fineness of the gold. If the use of plates is involved, the bullion may be adulterated, but the effect of any copper, or other metal, that may have been introduced can be cancelled by assuming that the gold and silver shouJrl add up to about 990 fine, or by ignoring the base metal content altogether, which varies little in naturally-occurring gold, and in calculating for comparison purposes all fineness figures to the basis Au + Ag = 1,000.The composition of bullion obtained from cyanidation is generally intermediate between the true gold fineness and the total gold-silver proportion as determined by assay of mine or mill-head samples of Cyanide solution dissolves other silver-bearing minerals and the fineness of the resulting bullion is thereby lowered. Consequently, the fineness of cyanide bullion rarely corresponds to the true gold fineness and is useless for diagnostic purposes, although it is a common fallacy to refer to the fineness of cyanide bullion as the fineness of the gold.

Jan 1, 1950