Search Documents

By Murat Alkan

In this study, a self-propagating high-temperature synthesis (SHS) and following acid leaching techniques were carried out to produce boron carbide (B4C) powder. First, B2O3 was obtained through calcinations of H3BO3 at 1073 K for 2 hours. Then, the glassy B2O3 obtained was crushed and sieved. In the SHS experiments, different amounts of B2O3, Mg and C black were used. The SHS product was obtained in the form of black, spongy solid. In the leaching step, the SHS product was leached in a HCl solution to eliminate the MgO and Mg3B2O6. The effect of acid concentration on the selective leaching was studied at different concentration range, solid/liquid (S/L) ratio, and temperature. The products obtained were characterized by using X-ray diffraction, chemical analysis and SEM techniques.

Jan 1, 2009

By W. W. Adams

[Sales of explosives - permissible explosives5/ other high explosives, and black blasting powder - in the United States during the calendar year 1937 reached a combined total that slightly exceeded the quantity sold in 1936. A larger output was reported for permissible and other high explosives but a smaller for black powder. Production of the three classes of explosives totaled 404,744,294 pounds, more than 3 percent over 1336. The total quantity produced included 49,579,441 pounds of permissible, 288,924,253 pounds of other high ex- plosives, 36,403,950 pounds of black powder in pellet form, and 23,836,550 pounds of black powder in granular form. Sales of granular black powder declined 26 percent compared with 1936 and of pellet black powder 12 percent; gales of permissible explosives increased nearly 4 percent and of other high explosives 10 percent]

Jan 1, 1938

By Charles E. Semler

The possible utility of selected compositions in the systems SrO-ZrO2-MgO and SrO-ZrO2-Dolomite for commercial refractory products was confirmed in this study. Specifically the compositions of interest are located in the sub-systems SrZrO3-ZrO2-MgO and SrZrO3-ZrO2-Dolomite. Both sub-systems have regions that are not affected by hydration, but the sub-system SrZrO3-ZrO2-MgO has a larger candidate compositional region. Solid state phase relations were determined for the subject systems over the temperature range 1600°C to 1300°C, with compatibility diagrams presented for each. The systems appear to show good refractory character with no apparent low melting compositions. As the compositions of commercial interest lie mostly in the higher ZrO2 portion of each system, information is presented regarding the firing treatment required to develop stabilized cubic ZrO2. A list of suggestions for further study of these systems, to further delineate the characteristics required for possible commercial utilization, is presented.

Jan 1, 1982

By J. R. Thoenen

In June 1929 the Bureau of Mines issued a 13-page information circular entitled "Mineral Wool," which was one of the first publications to present to the public Rome technical aspects of the mineral-wool industry. Since then several articles on the subject have appeared in the technical press as well as in publications of State organizations. Inquiries for information on mineral wool have continued to be received by the Bureau of Mines in large number, and in 1935 it was decided to make a field survey of the plants then producing and to collect therefrom technical data to be compiled in a paper for nubile distribution. With the cooperation of the industry, this survey was made, and Information Circular 6984, Mineral Wool, was published in January 1930. The issue was exhausted after a few months, and requests for copies continued to come to the Bureau. As opportunity arose, further field studies were made in American as well as Canadian plants. The present circular contains the essential information in Information Circular 6994 together with date from later field studies.

Jan 1, 1939

By D. F. Hambley

This report documents the work carried out by Engineers International, Inc. and its subcontructor, W. G. Pariseau, in order to develop a design manual for ore passes for open pit mines. The work included an extensive information search, novel analyses in rock flow theory, cost and time estimation for shaft and raise construction methods, and development of design criteria for the are pass proper, dump point, and draw point.

Jan 1, 1983

By J. J. Shields

With the increased use of mechanized equipment in mining bituminous coal, production panels are mined out rapidly. To keep current with the rapid completion of production panels, development work must be speeded up also. Although the same type of equipment usually is employed in development as in production places in the same mine, past output per man for development usually was less than from production panels. A study of development practices in 14 mines reveals a tendency toward equalization of the output per man between development and production.

Jan 1, 1957

By R. Hipsley, D. Arbonies, P. J. Dobak, M. Visher

The Storm deposit is a high grade breccia hosted “Carlin-type” gold deposit located at the north end of the Carlin Trend. Storm consists of 3 smaller deposits: 1) 49er Zone, 2) End Zone, 3) Discovery Zone. Structural intersections and favorable stratigraphy at the Paleozoic Popovich/Rodeo Creek formation and Bootstrap limestone formation contact are the primary known controls to gold mineralization at Storm. High grade silica-sulfide breccia occurs in the footwall of the north-south trending, dike filled, Dee fault. This mineralization cross-cuts silicified heterolithic breccia zones localized above the Bootstrap limestone where northwest, dike filled, reverse faults cut this structural-stratigraphic horizon. 40Ar/39Ar dates of 37.57+ 0.34 Ma (basalt dike) and 162 Ma (lamprophyre dike) have been obtained from dikes in the Dee pit which are locally mineralized by the same event as Storm. This paper will focus on the descriptive aspects of the Storm deposits.

Jan 1, 2001

By MANZOOR ALI BROHI, IZHAR MITHAL JISKANI, Atta Ur Rehman, SHUAI HAN, MUHAMMAD TARIQ, NIAZ MUHAMMAD SHAHANI

A thorough improvement in mine safety is contingent on many factors that require scientific decision-making for selection and prioritizing of important factors for safety improvement. Their analysis using an established scientific method can improve mines’ safety conditions and assist the administration for informed decision-making. This research establishes a mine safety evaluation index and proposes an integrative model based on the entropy weight and grey clustering methods. In the evaluation index, 27 significant factors of safety are identified and categorized into 7 criteria. The proposed evaluation system analyzes all indicators according to Pakistan’s current mine safety situation and their significance for potential safety improvement in the future. Results reveal that current safety practices are outdated due to a lack of mechanization in the mining industry and minimal capability of the management to achieve the desired safety targets. Appropriate safety policies and safety education are missing in the daily working environment. The lack of overseeing the execution of safety operations and the lack of ambition and strong work ethic workers contribute to the paucity of mines’ safety conditions. The prevention and control systems to manage risks and hazard are not in place, and the working environment in mines remain difficult. Therefore, to have enhanced mine safety, important factors can be addressed in chronological order, as presented in this paper. The proposed methodological approach can be applied to other prioritization applications to analyze the indicators and determine the appropriate management strategies.

Jun 14, 2021

By F. E. Lathe

INTRODUCTION THE present study, based largely upon phase equilibrium diagrams and other theoretical considerations but nevertheless addressed primarily to the practical metallurgist, has been undertaken with a view to discovering what light can be thrown upon the role of alumina in slags. According to Liddell (23), "alumina apparently acts as .a base if much silica is present, as an acid if the silica is low, always as a nuisance." Newton and Wilson (26) state that .alumina "is never added intentionally, as it makes the slag viscous, and is generally an undesirable constituent of slags". Camp and Francis (3) sum up their views by saying, "alumina is seldom used intentionally as a flux, but it is present in nearly all raw material, hence unavoidable". One has only to read The Function of Alumina in Slags, by Henrich (I3), and the very extensive discussion that followed the presentation of his paper, to realize that, before the days of phase equilibrium diagrams, it was a very serious question indeed as to whether alumina should be calculated as a basic, acid, or neutral constituent. Opinions then differed widely, as well they might; today, even though no categorical answer can be given to the question raised, the function of alumina can be at least partly clarified by a study of the fundamental work done by the Geophysical Laboratory in Washington and by certain universities in both America and Europe. It will be a source of gratification to Canadian metallurgists and ceramists to know that work of this type is now under way in the recently organized Physical and Crystal Chemistry Section of the Mines Branch, Ottawa, and that results of practical value have in fact already been obtained.

Jan 1, 1951

By S. Banisi, M. Pourkani, A. Kargar, D. Hamidi, M. Sarvi

"Flotation circuit of the Sarcheshmeh copper mine, which processes 40,000 t/d of ore at 0.9% Cu, consists of rougher, cleaning and recleaning stages. To study the stage recovery of copper, one of the eight identical flotation banks was selected for sampling. It was observed that 17% of copper goes to the tailings and the lowest copper recovery was for particles coarser than 105 microns. The third five-cell unit of this bank not only did not recover appreciable amount of copper but also decreased the concentrate grade. The grade of the last five cells was lower than the feed grade suggesting that mixing of the concentrates of the three units was not beneficial. To alleviate the problem, the concentrate of the first four-cell unit was directed to the cleaners feed box (i.e., by- passing the regrind mill). This increased the overall copper recovery by 1.7 %. Also rather than the current practice of adding the reagents only at the feed tank (i.e., 100-0-0%), various combinations of stage addition were examined. It was found that 75-25-0% addition regime could increase the total copper recovery by 1.3%. At the recleaning stage in order to increase the final copper concentrate grade, a froth washing system was used. To ease the maintenance of the system, a shower type washing system was installed. The optimum wash water superficial flowrate was found to be 0.06 cm/s. Continuos sampling of the recleaners with and without wash water over a period of two months showed an increase of 1.5% in the final copper concentrate grade at constant overall copper recovery.INTRODUCTIONThe Sarcheshmeh copper ore body that may rank as third or fourth largest in the world contains 1 billion tonnes averaging 0.9% copper and 0.035% molybdenum. It is located in southeastern Iran and has been processing 40 000 t/d of ore since 1982. The mine produces 100 000 tonnes of copper and 2200 tonnes of molybednite concentrate per year.After three stages of crushing, the ore with a F80 (80% passing size) of 12.7 mm is fed to eight parallel ball mills in closed circuit with cyclones to produce a product 70% finer than 75 microns. The concentrate of rougher flotation circuit is ground; rougher tails constitute the main component of the plant final tailings. A concentrate with an average grade of 31% Cu (chalcocite and chalcopyrite) is obtained after cleaning and re-cleaning stages. Total recovery of the plant varies between 83% and 87%, depending on operating conditions and ore type."

Jan 1, 2001

By R. B. Anderson

As a part of a Bureau of Mines program on the conversion of coal to liquid and gaseous fuels, the kinetics of the Fischer-Tropsch synthesis on iron catalysts was investigated. Nitrided catalysts were studied at 21.4 atmospheres using feed gases ranging from 2H2+1CO to 0.25H2+1CO, and at 7.8 to 21.4 atmospheres using 1H2+1CO gas. The overall apparent activation energy increased with increasing carbon monoxide content of the feed gas from 19.5 kcal/mole for 2H2+1CO to 23.7 for 0.7H2+1CO. The rate of synthesis with 1H2+1CO feed increased linearly with operating pressure from 7.8 to 21.4 atmospheres. A semifundamental rate equation of the form [r=a'PH2 0.6pco 0.4- ?r0.5PH200.5] was shown to fit the data satisfactorily. The relative usage of hydrogen to carbon monoxide decreased with increasing conversion, passed a minimum, and then increased. Apparently water is the principal primary product and carbon dioxide is produced by subsequent water-gas shift reaction. In another group of experiments water, carbon dioxide, argon, and methane were added to 1H2+1CO feed to a nitrided iron catalyst. Argon and methane were only diluents. Carbon dioxide was a slight inhibitor and water vapor was a strong inhibitor to the rate of synthesis. Water accelerated the water-gas shift and usually increased methane production. Important factors of catalyst geometry in determining rate were found to be particle size and extent of reduction. Apparently the active portion of the catalyst is confined to a layer of 0.01 to 0.02 cm from the external surface of particles. A special solution was made of differential equations relating re¬action at the catalyst surface to diffusion in pores of the catalyst for spherical particles with an active layer surrounding an inert core. The equation derived expressed the experimental data reasonably well. Diffusivities determined by this equation varied from 3 to 24X10-6 cm2/sec; these values are of the same magnitude as observed for the diffusion of gases in liquid. The appendix presents a group of synthesis experiments at pressures of 21.4 to 103 atmospheres. In this range the rate of synthesis on nitrided iron catalysts increased with pressure to the 0.74 to 0.84 power.

Jan 1, 1964

"8.1. IntroductionThe stoichiometry of most named platinum-group minerals (POM) is known (cf. Cabri, 1981b, in Chapter 7), but, because these minerals are subject to a wide range of element substitutions, representative analyses require treatment in a separate chapter (section 8.2). The analyses, in all cases done by electron microprobe, are grouped in sections according to the principal platinum-group element (POE) for each POM, and then follow sequentially with increasing amounts of the principal POE starting with the ideal composition, when known. In order to facilitate reference to specific POM by name, an alphabetical listing is also given (Table 8.1). A range of compositions, in addition to one or several ""representative"" analyses, is given for some POM when more than one analysis has been reported for a particular locality. The tables of POM analyses (Tables 8.2 to 8. 76) include at least one analysis for every locality for which data have been published, to the best of the authors' knowledge. All analyses are referenced for locality and publication source, and include several unpublished analyses (all but one done at CANMET). Most analyses have been rounded off to one decimal place for amounts more than one per cent and their formulae calculated on the basis of an even number of total atoms. In all tables, ''n.d.'' stands for elements sought for but not detected and a dash signifies elements not sought, or when these haven't been specificed in the publication source.Section 8.3 contains tabulated analyses and, in some cases, also includes a critical assessment of POE-bearing minerals in which the POE occur in trace or minor quantities. The organization of the data in this section is by mineral groups; e.g., sulphides, sulpharsenides, silicates, etc. Some of these data are also discussed in Chapter 4 by Crocket (1981) and are discussed briefly in Chapter 6 by Crocket and Cabri (1981)."

Jan 1, 1979

By Bjarne Ekberg

"The most economical way of dewatering mineral concentrates is to reduce the moisture content in the material mechanically using thickeners and filtration avoiding thermal drying whenever possible. In addition to this, the dewatering process should produce low moisture cake, high quality liquid, consume little energy. As a part of the dewatering process The CERAMEC® capillary filter has been proven to meet these requirements in over 150 installations. The filtration is done by using ceramic filter plates with small pore size. The capillary action in the filter medium secures gas free filtration at good vacuum, and due to the small pore size, filtrate is crystal clean and particle free. The energy consumption is minimal. This paper will discuss results from filters installed at Pyhäsalmi Mine Oy in Finland where the technology was has been used since the late eighties. Results from more recent installations like Los Pelambres in Chile and LKAB in Sweden will also be discussed.INTRODUCTIONThe idea of using capillary action to make dewatering more efficient was invented two decades ago. Ten years later whole filter plants utilizing the new method were delivered to mine concentrators for dewatering of mineral concentrates. Further development of ceramic membrane plates made it possible to meet the requirements in iron ore dewatering. In addition to low cake moisture, high capacity and low energy consumption, there are a lot of environmental advantages in using capillary filtration. One of them is clear filtrate.CAPILLARY FILTRATIONA micro-porous filter material behaves like a large number of narrow capillaries forming a network. When a pressure difference ?P is applied over the wetted, hydrophilic pore with the radius r, the force striving to push the water out of the pore will be ?Ppr2. The force striving to hold the water in the pore will be the vector force 2pr? cosa of the surface tension ? and the cosine contact angle a. Equalling those forces and solving the equation for ?P we get"

Jan 1, 2003

By Fahimeh Dehghani, Louis Ackah, Tathagata Ghosh, Justin Godbold, Jia Liu, Meisam Peiravi, Manoj Mohanty, Azam Baharlouei

Primary economical deposits of rare-earth elements (REEs) are exhausting all over the world, and it has become necessary to find new sources and methods for their extraction. In addition, increasing the application of REEs in modern technological society has increased its demand globally. One of the important movements to compensate for the future shortages of critical metals is the recovery of REEs from recyclable materials. This paper presents a review of the classification and extraction methods, as well as general applications of REEs with emphasis on secondary sources such as coal and coal byproducts, iron ore tailings, apatite, and phosphate byproducts. An overview of the current state of knowledge on the various methods of REE beneficiation and extraction is covered. These methods include physical separation, as well as hydrometallurgical and bio-hydrometallurgical techniques. The application of these REE extraction techniques for enhanced recovery has been driven primarily by the unique industrial application of these important elements. This paper further explores the existing and potential environmental challenges associated with REE extraction. The authors have presented a wide array of literature, in-depth discussion of the subject, and a succinct summary of processes and relevant case studies.

Sep 23, 2020

By Stanisław Prusek, CHONG WEI, Huawei Xu, Jun Wang, Andrzej Walentek, Artur Dyczko, Derek B. Apel

The excavation-induced stresses transferred from the panels or pillars in upper coal seams play a key role in the occurrence of rockbursts in driving roadways during close-distance coal seam mining, which has become a common problem and threat to many underground mines. The authors established a 3D finite-difference numerical model via FLAC3D software using the closedistance coal seam mining conditions in the Zofiówka Mine as a case example to reveal the rockburst mechanism in such conditions. The excavation-induced vertical stresses are analyzed, which provides a basis to build a conceptual model to explain the possible source mechanism of the rockburst under such conditions. Nine typical rockburst indicators considering different contributing factors are then selected as the evaluation criteria to assess rockburst potential in the study site. The results suggest that the superposition of multiple excavation-induced stresses of the main drift and tailgate provides an environment for stress concentration and energy accumulation. The side abutment stress induced by mining in the upper coal seam has a “strengthening” effect to the rockburst occurrence. The great deviatoric stress induced by complex excavating situations is another important exterior cause. A strict calibration procedure should be implemented before using indicators to predict rockburst potential. A methodology was proposed to estimate the location and magnitude of rockbursts combined with numerical modeling, laboratory tests, and feedbacks from the field. The study could provide some references and guidelines for preventing and mitigating rockbursts in underground mines under similar engineering conditions.

Aug 26, 2021

By M. B. Shongwe, R. K. K. Mbaya, C. K. Thubakgale, P. Mendonidis

"A low-grade nickel-bearing ore was pre-concentrated on a SB40 laboratory model Falcon Concentrator. Three size fractions, -212+125, -125+75 and -75 µm were tested with the intent to upgrade the nickel content by reducing their content of fine silica, which becomes amorphous during leaching. Separation of silica from nickel-bearing magnesium silicate minerals; hornblende, clinochlore and talc, was more efficient in the finer particle sizes, -125+75 and -75 µm, and at high G-forces. For these two size fractions, nickel was upgraded from 0.06 to 0.07%, with a reduction in silica content from 52.12 to 50.71%. Leaching of feed samples prior to pre-concentration resulted in the formation of amorphous silica, indicative of the presence of fine silica in the samples. Leaching of nickel from the -125+75 µm fraction increased with increasing G-force and feed pulp percent solids, while that of -75 µm was not influenced. The optimum nickel recovery was 15.68% to the Falcon underflow, using the feed size fraction of -75 µm, 30 G and a feed pulp solids content of 10% solids, after 120 minutes of treatment.INTRODUCTION A low-grade South African nickel-bearing ore with about 0.06% Ni was previously studied for atmospheric pressure acid leaching using sulphuric acid. The study was motivated by the continuing search for methods to treat of low-grade ores, which appear to be an increasingly important source of valuable metals as a result of a declining production from rich sulphide ores. Nickel is a base metal that is used as an alloy in steelmaking and chemical industries because of its resistance to corrosion (Haudet et al., 2015). Nickel laterite ores with grades lower than 1.50% Ni are considered to be complex ores, accounting for 70% of the global nickel reserves (MacCarthy et al., 2016). Their complex nature may be attributed to the indefinite mineralogy of these ores, in which nickel may occur in more than one mineral host. In some cases, nickel may be finely disseminated in the ore. The grade of such an ore and complex mineralogy do not justify the application of pyrometallurgical methods for extraction of nickel (Zhu et al., 2012). This suggests that there is a need for less expensive alternative methods of extraction. This study investigates the application of centrifugal gravity concentration, using the Falcon concentrator, followed by leaching to determine the effect of pre-concentration of the ore prior to extraction by atmospheric pressure leaching with sulphuric acid."

Jan 1, 2017

By Robert L. Stephens

"It can be argued that one of the most important property of any material is cost, since this property detennines the applications for which a material can be considered. Despite growing demand and production for commodity metals such as copper, nickel, zinc, lead, and tin, the cost of these metals has been steadily decreasing in real terms. The only way that metal miners and producers can remain financially viable in the long term is by continuing to lower their cost curve through the implementation of new metals production technologies. This paper reviews technological developments in the production of copper, nickel, zinc, lead, and tin that have or threaten to redefine the cost curves for these metals.DisclaimerThe opinions expressed in this paper the author's, and are not necessarily those held by the author's employer, Cominco Ltd.IntroductionThis meeting will discuss many novel technologies and processes for producing metals and materials with specific properties that will enhance the applications ranges for the material or will allow entirely new applications to be developed. However, in every real-world case, the cost of the new material or process is an important property that determines which applications the material or process can be used in. Other properties that are important depend on the applications.A recent press report (1) discussing the potential replacement of aluminum radiators with copper radiators in pickup trucks and sport utility vehicles provides an interesting example to reinforce the importance of cost in materials selection. In this case, the displacement of aluminum by copper is being considered because of the more favorable heat dissipation characteristics of copper. Heat dissipation has become more important due to the development of hotter-burning V-8 and V-6 engines. For this application, engineers also consider cost, weight, size, durability, and manufacturing process. The report stated that the development by the International Copper Association (ICA) of the ""CuproBraze"" manufacturing process for heat transfer products was an important development. This technology produces 845 radiators that weigh less, are more uniform in quality, and are potentially more compact. They are also expected to cost less in high production quantities than copper units produced in the past, last three to four times longer than soldered copper radiators, and the process also eliminates the use of lead solder from the manufacturing process."

Jan 1, 2000

The phosphorus content of the banded iron formation (BIF) and of the associated iron ore deposits in the north west of Western Australia is known to vary widely, a fact which has considerable econ~mic significance. Trendall and Blockley (1970) have described the variety of textural appearances of apatite in the Hamersley Group BlF, and suggest that apatite may account for the entire phosphorus content of the unaltered BIF.A preliminary investigation using an M.A.C. electron microprobe analyser has shown that, at least in some iron ores and in partially enriched BIF and associated shales, the phosphorus occurrence is more complicated than this. A suite of samples was examined from one location which covered the entire Dales Gorge Member and some adjoining macrobands in the Mt. McRae shale, together with samples selected for their high phosphorus content, degree of ore enrichment, and position relative to the enrichment zone. Calcium apatite was not observed in any sample of ore from this sequence, despite its ubiquitous occurrence in the BIF. Silicate mineralogy in the enriched regions also differs from that in the BIF, but this change has not yet been studied in detail.The phosphorus content of goethite in one orebody is often high and appears to be in solid solution in the goethite structure. It shows little or no variability on a micro-scale within a grain, except where theremay be a zoned enrichment near boundaries and solution channels. There is also a limited solubility of phosphorus in hematite (the maximum observed by the author is 0·1 per cent P); but where the hematite is martitic (after magnetite) its phosphorus content is always low or zero. In some bands, martitic hematite has been hydrated to goethite, and this also has a very low phosphorus content. Phosphorus was not found in the silica or silicates in the ore, and even when iron enrichment is just beginning, a limited suite of samples from the BIF suggests that the phosphorus content of the chert microbands is almost entirely in the microscopic goethite nuclei (after riebeckite) scattered throughout the chert. The ability of goethite and hematite to accept phosphorus...

Jan 1, 1973

By Dave Bulled, Khiratt Husain

"The use of High Pressure Grinding Rolls is gaining significant interest as a replacement for SAG milling in the comminution of hard rock ores because of the potential for reduced costs in terms of energy and grinding ball consumption. Estimation of expected energy consumption for fullscale operations has conventionally involved the testing of a few fairly large samples in pilot scale HPGRs. This paper describes the development of a small-scale batch test method for determining a work index for HPGR of a large number of samples that can be used to show the variability of the ore as an integral part of a geometallurgical approach to circuit design and production forecasting.The test equipment that was developed comprises a hydraulic press with adjustable pressure operating on small batches of ore in a locked cycle test procedure. A work index measurement was determined that links the specific energy consumed in the test to the breakage achieved such that the index can be used to predict comminution energy requirements.The measurements were calibrated against laboratory scale HPGR equipment to develop a model for design and forecasting that includes crushers, HPGRs and ball mills in a complete comminution circuit.INTRODUCTIONEstimation of the expected energy consumption for full-scale HPGR operations has conventionally involved the testing of a few fairly large samples in laboratory and pilot scale machines (Danilkewich, 2006). With the financial input of five mining corporations, SGS Lakefield Research has developed a small scale test capable of providing relevant information on the variability of energy consumption and size reduction from drill core samples. It is our intention that the values measured in the test will be scaled up, through benchmark comparison with pilot sized and full sized HPGR units, to allow plant design and throughput forecast on a block by block basis of the mine plan using a new CEET program. CEET® (an acronym for Comminution Economic Evaluation Tool) is an advanced grinding design and performance predicting tool that uses energy relationships to model the performance of SAG / Ball mill circuits."

Jan 1, 2008

By Richard Curtis

Optimum Colliery is presently experiencing a shortfall of stripping capacity in order to meet its production requirements. Due to the long dragline procurement times, several alternative stripping methods were evaluated in order to alleviate this shortfall in the interim period. Based on the experience gained at the mine. The writer will discuss some of the important factors which influence dragline performance and show how these factors may by used in a theoretical approach to analyse various dragline applications.

Jan 1, 1990