Search Documents

By G. R. Purdy, J. A. Malcolm

The isothermal dendritic precipitation of y in p CuZnSn is compared with the isothermal formation of Widmanstatten a plates in p CuZn. Although both precipitates are evidently bounded by semicoherent interfaces, the dendritic shape of y evolves through smooth "sinuoidal" shape perturbations, while a-p interfaces tend to be strictly planar, or rnicroscopically faceted. An estimate of the average inter-facial free energy of cube-oriented y in p through the Mullins-Sekerka analysis indicates that it is low (of the order of 50 ergs per sq cm). Interface mication is apparently controlled by volunle dij'usion, and the observed anisotropy in growth probably results from anisotropy of inter facial free energy. Studies of the grain boundary precipitation of y in p indicate that the precipitate can grow in both $ grains, but becomes unstable with respect to the grain with which it shares a mobile semicoherent interface. Facets observed at the tips of Kurdjumov-Sacks-oriented Wid-manstatten a plates correspond to variants of an irrational hahit, near (231)0. Comparison with Hu and Smith's determination of relative interfacial free energies of a-(3 boundaries suggests that this system possesses an extremely deep o cup, which results in an ej'ective low-o zone. The possible effects of such a cup on the stability of a-p interfaces are discussed, a needles, grown during rapid continuous cooling, possess microscopically smooth interfaces, and are characterized by a high degree of' damage in the region of the boundaries. These boundaries, induced to move on tempering at 200"C, become faceted as equilibrium is approached, which seems to indicate that boundary structure and mobility in this system are dependent on the local degvee of departure from equilibrium MULLINS and sekerkal have elucidated the phase boundary stabilizing effect of surface tension. a factor not taken into account in previous treatments of morphological development. Their analysis applies to the isothermal growth of a pure spherical precipitate (planar in the limit of infinite radius) in a slightly supersaturated solution, under conditions of inter-facial local equilibrium and isotropy of interfacial free energy. More recently, several other factors which might tend to stabilize planar interfaces have received attention. These are: i) interface diffusion;4"8 and ii) slow interfacial reaction. cahn7 included a slight anisotropy in interfacial free energy, and showed that it has no stabilizing effect, but forces shape perturbations to reflect the anisotropy. shewmon4 noted that dendritic morphologies are rarely observed in solid-solid systems, and, in particular, postulated that slow interfacial reaction occurs at all boundaries between proeutectoid ferrite and austenite, except those which propagate parallel to {11 l)y planes (for Kurdjumov-Sachs [K-S] related phases). Previously, Aaronson~ had proposed interfacial reaction at the broad faces of Widmanstatten plates, and expected that the lateral motion of high-mobility incoherent ledge edges would produce planar precipitates bounded by law-mobility semi-coherent interfaces. The problem of interfacial reaction during the dif-fusional formation of precipitates has often been ignored, although it is apparent that a small component of chemical reaction must exist at any moving interface." Further, all solutions of the diffusion equations for boundary conditions corresponding to isothermal growth predict infinite growth rate at time zero, so that elements of interfacial reaction would be most easily detected at early times. However, reported deviations from diffusion control are comparatively rare," and the local-equilibrium diffusion-control model appears adequate for the description of many isothermal growth systems.'2"9 Cahn14 has treated the problem of migration of an interface which is able to reach positional energy minima, and concluded that such an interface, if subjected to a high local ther-modynamic "driving force", may migrate normal to itself without the benefit of ledges. As local equi-

Jan 1, 1968

The inherently explosion-proof mine (EPM) concept is based upon the non-flammability of certain combustible-oxidant-inert gas mixtures, and the effect of partial pressure of gases on physiological reactions. In a properly controlled underground environment, gas explosions are impossible, men can do work, and relatively high concentrations of methane would be permitted. A systems analysis has been performed to examine the physiological, engineering, and economic feasibility of such a concept, and methods and equipment are recommended for maintaining an EPM atmosphere in a bituminous coal mine producing a nominal two million tons of clean coal per year. It is concluded that: engineering feasibility can be demonstrated using subsystems and components that can be designed and built within the present state-of-the-art, that economic feasibility is possible within approximately five years, and that physiological feasibility is sufficiently promising to warrant continued investigation.

Jan 1, 2012

By Herbert D. Drechsler, James B. Stephenson

"AbstractThe paper identifies the major components of price change which affect the determination of the internal rate of return of a mining project. It illustrates several price indexes which may be used to measure general price increases, identifying techniques which might incorporate them into mine valuation procedures. The ""hurdle rate"" for new investment is discussed.IntroductionDECISIONS regarding the value of an orebody and whether or when to mine an orebody are based on an estimate of the cash flows which would be associated with its exploitation. These pro-forma cash flows represent cash in or out of a possible mineable deposit and include exploration and construction costs, sales revenues, operating expenses, taxes, debt borrowings, interest and debt repayment. It has long been recognized that when combining the cash flows occurring over the life of the mine, dollars received or paid out early have greater value than those received or paid out later. This time value of money has been incorporated into mine evaluation calculations through the use of present-value or discounting techniques. Another factor affecting mine valuation, inflation, is not accounted for by valuation techniques now in use. In recent years, price changes have become more volatile. In the past, price change could easily be ignored when evaluating potential mines. Today, the combination of larger investments and greater price volatility leads to great concern about the effects of price change on mine valuation."

Jan 1, 1977

By Jr. Brinkley

For a theoretical description of power plants that derive their energy from the combustion of a fuel, it is necessary to solve, to an appropriate degree of precision, a hydrodynamic problem that requires for its solution a knowledge of the thermodynamic properties of the working fluid com-posed of the products of the combustion reaction. It is usually a good approximation to assume that the properties of the combustion gas are determined by the conditions of thermal equilibrium, and it is thus possible to employ the methods of Classical thermodynamics for their computation. The thermodynamic properties of fuel gases also are of considerable importance, as they form the basis for the design of appropriate means for their effective utilization. The specification of the operating conditions to produce a gas for use as an intermediate in a chemical process, such as the synthesis of liquid fuels, may be based upon a study of the variation of the composition of the synthesis gas with changes in the various process variables. Although there exists a large number of important scientific and technical applications of the data that can be obtained from the systematic determination of the thermodynamic properties of combustion gases, such application has been greatly handicapped by the extremely tedious and time-consuming computational methods required. The development of large-scale automatic computational equipment makes feasible the initiation of a systematic program for the determination of the thermodynamic properties of combustion gases and for the application of such data to specific problems of scientific and technical importance. As a part of its program of basic research in flame and combustion phenomena, the Explosives and Physical Sciences Division of the Bureau of Mines is engaged in such a program. The present communication is designed to introduce a series of reports presenting the results of this program.

Jan 1, 1951

By D. D. Walker

Scheelite, the most abundant tungsten mineral in the Philipsburg region of Montana, is found in replacement deposits and along fissures and cracks in limestone at various distances from contacts with acidic igneous rocks. It also occurs at the limestone-igneous contacts, but typical garnet tactites are developed in only a few places in the region. The most favorable host rocks for scheelite mineralization are the Jefferson, Hasmark, and Madison limestones. Scheelite is exposed in float, outcrops, and surface and mine workings along a 2-mile-wide belt extending southwest from Lost Creek beyond Silver Lake, a distance of 15 miles or more. (See fig. 1.) Some scheelite is found in veins formerly mined for silver. Powellite and molybdenite occasionally are present with the scheelite. Hubnerite occurs in quartz veins in the Black Pine area 10 miles northwest of Philipsburg. These quartz veins occur in the quartzites of the Precambrian Spokane formation. Tungsten production in the region has come almost exclusively from scheelite deposits, both lode and placer. During a 6-year period beginning in 1943 a total of 142.0 tons of 63-percent W03 concentrate was produced by H & H Mines Co. In the early 1950's, the Trigger mine produced 4,000 tons of 1-percent W03 ore and the Tip Top 650 tons of 2.0-percent W03 ore and 2,906 tons of 2.2-percent ore. There has been sporadic production from some of the smaller properties in the area.

Jan 1, 1960

By David Schlain

IN 1942 the Bureau of Mines began to develop the Kroll process for use in the large-scale production of titanium. Titanium and titanium alloys are now commercial metals. These metals are relatively expensive, but It is now evident that they will have important industrial uses and that in many instances these will be related to their remarkable corrosion resistance. This bulletin presents the known corrosion properties of titanium and its alloys in useful form. In marine environments titanium is highly resistant to corrosion and does not pit, or undergo crevice corrosion, stress corrosion, or corrosion fatigue. Titanium is also highly resistant in many salt solutions, including most chlorides. It is very resistant to corrosion in nitric acid solutions. It is also resistant to white fuming nitric acid. However, it may react violently with red fuming nitric acid. In phosphoric acid solutions titanium has rela¬tively good resistance to corrosion, but it has less resistance to sulfuric acid and still less to hydrochloric acid solutions. Titanium corrodes very rapidly in hydrofluoric acid Solutions. It is very resistant to corrosion in many organic chemicals. However, it has only moderate resistance to formic acid solutions and poor resistance inn oxalic acid solutions. Titanium does not corrode in dichloroaretic acid but, corrodes rapidly in 100 percent trichloroacetic acid at 100° C. Titanium is resistant to barium, calcium, magnesium, ammonium, and sodium hydroxides. Titanium is inert in wet chlorine, bromine, or iodine gases. However, in dry chlorine gas titanium reacts rapidly enough to ignite. It also reacts rapidly with dry bromine gas, but, it is resistant to dry iodine gas. When titanium is exposed to red fuming nitric acid solutions with high nitrogen dioxide content and low water content, it corrodes, undergoes stress-corrosion cracking, and becomes pyrophoric. This occurs more readily with some titanium alleys, such as titanium-8 percent manganese. A fresh titanium surface immersed in water or in an aqueous solution and in contact with an oxygen-rich atmosphere under sufficientt pressure is unstable and will ignite spontaneously. Inherently an active metal, titanium has a tendency to become less active in environments containing oxidizing agents such as air, oxygen, chlorine, or ferric, cupric, or platinic ions. Titanium is more noble than most structural metals in roost, environments and its excellent corrosion resistance is generally not, affected by contact with these metals. However, some of the other metals corrode faster because of contact with titanium. Titanium undergoes anodic polarization readily, so that even when it is the less noble member of a galvanic couple it may corrode less because of the contact. Titanium alloys often have corrosion properties and electrochemical characteristics similar to those of commercially pure titanium. Titanium alloys containing noble metals, zirconium, molybdenum, vanadium, tantalum, or copper sometimes have better corrosion resistance than pure titanium.

Jan 1, 1964

By E. A. Gulbransen, J. W. Hickman

DURING the past two decades considerable progress has been made in the art of manufacturing heater alloys. The conventional iron-chromium-nickel alloys have been improved by the addition of small quantities of other elements. Up to the present time, to our knowledge, there has not appeared a systematic study of these alloys where the newer tools of investigation have been brought to bear on the problem. It is not yet clear what roles the additional elements play in increasing life time in usage. As a first approximation one might guess that elements such as manganese, silicon, zirconium, calcium and aluminum would aid in the formation of a protective film on the alloy surface, thus retarding the oxidation rate and increasing lifetime. If these additional elements do form protective oxides in the outer surface of the oxide film, it may be possible to identify them by means of reflection electron diffraction. It is also possible that the additional elements may not diffuse to the surface but may remain at the interface between the oxide and the metal. Then, too, the major elements in the alloys undoubtedly form oxides which are stratified on the surface. If the minor elements concentrate in a layer in contact with the substrate where they undergo oxidation and if this oxide film offers resistance to the diffusion of iron, chromium and nickel ions, then the lifetime of the heater element might be expected to increase. It is also possible that preferential reduction in the diffusion rates of the several ions may Occur to such a degree that oxides may form in the body Of the film and On the outer surface which are different from those that would normally form if the additional elements were not present. The use Of transmisson electron diffraction may aid us in jnterpreting these phenomena. UP to the Present time all Of the factors which influence the lifetime of a given heater element are not definitely known. Among these are: (I) The rate of oxidation of the alloy. This may be dependent upon the composition and the physica1 state of the "alloy. (2) The stability of the structure of the coating which forms. Transitions from one structure to another or solid phase reactions resulting in a change of composition may occur. The tendency of the film to adhere to the substrate when heated and cooled successively will be important. (3) The evaporation of various constituents from the alloy such as the remova1 of carbon by Oxygen in a decar-burization reaction. With these possibilities in view, an electron diffraction study of the oxides occurring on six different nickel-chromium alloys was undertaken with the hope that the results of this study could be correlated with oxidation rate studies as determined by means of the vacuum microbalance method1 and with lifetime tests carried

Jan 1, 1949

By M. C. Flemings, F. R. Mollard

Two-phase Pb-Sn alloys, ranging in compositiotz from 12 to 26 at. pct Pb, were unidirectionally solidified in a convection-fvee system, with thermal gradients in the liquid of up to 480°C per cm. Plane front solidification Loas achieved in all alloys at sufficiently steep gradient and slow growth rate. Conditions causing breakdown of the interface to a cellular or dendritic structure were roughly as predicted by a sinlple constitutional supercooling criterion. Structures of alloys of near-eutectic composition, solidified with plane front, exhibited a lamellar structure; the alloys furthest from the eutectic exhibited a rod-like morphology. Assumptions used in a previous paper for calculations of solute redistribution in two-phase plane front growth are shown to be reasonable for Pb-Sn alloys. Results of calculations are in good agveement with experiment. These show that variations in growth rate during solidification of the composite produce marked changes in average composition of the solid. IN a previous paper, Part I,' conditions necessary for plane front solidification of two-phase alloys were discussed and calculations given on solute redistribution in this type of solidification. This paper, Part 11, describes experiments on Pb-Sn alloys, designed to check the assumptions of the analyses presented, and to demonstrate their applicability to a given alloy system (Pb-Sn). APPARATUS AND PROCEDURE General. A vertical crystal growing unit was built for the study as described below, and "normal solidification" employed throughout (i.e., the ingot was completely melted except for a portion near the bottom end and then solidification initiated). The furnace was designed to permit achieving very low interface velocities, and steep gradients, in essential absence of convection; it is sketched in Figs. 1 and 2. Simple heat flow considerations indicated choice of a small-diameter specimen (ingot) to achieve high thermal gradients; ingot size chosen was 0.3 cm in diam. The ingots were held inside silica tubes 0.06 cm wall thickness. The requirement for an essentially convection-free system was met by use of the vertical furnace with the heat source over the heat sink, as well as by use of the small diameter ingots. In addition, by selection of tin-rich Pb-Sn alloys, the diffusion boundary layer (lead-rich) was denser than the bulk liquid and would not cause convection. The only apparent driving force for convection in this system was the small transverse temperature gradient resulting from heat flow into the samples from the furnace. Such convection must have been small, however, since 1) no temperature fluctuations in the melt were noted in the recordings, which would have indicated turbulent convection, and 2) experimental results obtained and described below could not have been achieved in presence of significant convection. Ingot Preparation. Pb-Sn alloys ranging from 12 to 26 at. pct Pb were prepared from high-purity lead and tin (99.9999 pct pure metal). Each alloy was prepared by first melting the pure metals in the proper ratio in air, in a Pyrex container. The melt was then stirred thoroughly with a graphite rod and cast into a preheated graphite mold. Ingots were then prepared from these castings for use in the actual experiments; each ingot consisted of a rod of alloy, 15 cm long in a 25-cm-long transparent fused-silica tube, 0.3 cm ID and 0.06 cm wall thickness. One chromel-alumel thermocouple, made with 0.004-in.-diam wire and protected by a two-hole alumina tube, was inserted into each ingot. The 1.5 cm of the thermocouple nearest the bead were protruding from the alumina tube and were coated with a very thin layer of boron nitride paste which provided electrical insulation while allowing good heat conduction. The electrically welded junction size was about that of each wire and the cross section of the two wires represented about 0.3 pct of the sample cross section. Including the coating, the thermocouple cross section still represented less than 0.5 pct of the ingot cross

Jan 1, 1968

By M. W. Lewis, J. Werner

Fluctuating metal prices, declining head grade, and increased operational costs are forcing many open pit mining companies to look to their balance sheets for significant cost reductions in order to remain competitive. Maintenance continues to represent a significant proportion of the total operating costs in the mining industry. Compared with the other major cost components of the mining process, very little effort has gone into maintenance optimization. The potential payoff from maintenance optimization on the cash cost of the commodity is enormous. A large percentage of these costs are incurred in unscheduled maintenance events, which typically cause serious disruptions to the production process. These maintenance-induced production losses can be a significant contributor to the overall operating costs. A structured proactive maintenance approach using the latest advances in technology can achieve dramatic cost reductions and productivity improvements. Remote condition monitoring systems are becoming increasingly commonplace and have the potential to identify problems prior to failure. Detection of equipment degradation prior to failure will enable repairs to be scheduled thereby reducing costs and interruptions to production. Remote condition monitoring technology has evolved rapidly in recent years, with a host of new tools becoming available to assist mine operators in improving their maintenance operations. These tools have capabilities such as remote real-time vital signs and performance monitoring, alarm/event handling, trend analysis, and maintenance workflow management. When these monitoring tools are used in conjunction with a mine management system, the vital signs data can be integrated and associated with maintenance history, predictive maintenance data, operational information, and geographical information. This integrated approach to the management of vital maintenance data will help shift the mobile equipment maintenance paradigm from reactive to proactive. This paper will introduce a proactive approach to the management of the maintenance process and the tools required to facilitate this process.

Jan 1, 2005

By Huang Zhiwei, Paul Skayman, Kevin Holley

In 1989 The First Brigade for Geology and Mineral Exploration of Qinghai Province discovered gold at Jinlonggou and Qinlongtan, Tanjianshan. Between 1992 and 2002 small scale mining was carried out at these sites using underground mining methods at Jinlonggou and an open pit at Qinlongtan. During 2003 and 2004 geotechnical investigations were carried out in support of a bankable feasibility study. An important objective of this investigation was to meet both internationally accepted standards and codes of practice, and also to satisfy the Chinese requirements. Extensive use of local experience was utilised. Where possible geological drilling information was incorporated into the assessment. Extensive geotechnical mapping of surface and underground exposures, and index testing to gain an appreciation of rock intact strength were used to characterise the sites. Rock mass classification (MRMR) was used to assess indicative overall slope angles and appropriate bench stack heights for the proposed pits at Jinlonggou and Qinlongtan. Measured discontinuity orientations were used in kinematic analysis to assess stability of possible pit slope geometry at a batter and overall scale to provide preliminary recommendations for the pit slope configuration. Numerical modelling was also carried out to improve the understanding of anticipated pit behaviour. Site investigation and preliminary geotechnical design details, that incorporate site specific conditions for the formation of open pits at Tanjianshan, are discussed in this paper.

Jan 1, 2006

The mine surveillance and communication system hereafter described provides continuous local and remote monitoring of several parameters critical to normal mine operation at each of ten underground sites in the Bruceton Research Mine. The techniques employed are well proven and have been care-fully chosen to provide the best solution to the technical problems involved while giving special attention to economic considerations.

Jan 1, 1973

By Robert E. McIvor

"“Classification System Efficiency (CSE)” is a powerful, emerging tool that can be used to increase grinding circuit efficiency. It is defined as the percentage of the ball mill energy being used to grind target, oversize particles. The discovery, validation and current use of CSE, including how it was manipulated, are described through seven plant case studies. These resulted in efficiency improvements ranging from 3 to 30 percent, along with major reductions in over-grinding. The achievable CSE for any given circuit is described. This paper demonstrates both how, and how much, every plant can benefit from increasing grinding circuit CSE.DEFINITIONS: BALL MILL CIRCUIT “CLASSIFICATION SYSTEM EFFICIENCY (CSE)”, “EFFECTIVE MILL GRINDING POWER”: “WASTED/OVER-GRINDING MILL POWER”The closed ball mill circuit is shown in Figure 1. The extreme importance of the circulating load ratio in determining circuit productivity was demonstrated by Davis (1925) and re-published by Guadin (1939), as shown in Figure 2. The circuit production rate increases with increased circulating load ratio, rapidly so at first and continuing to increase more gradually with higher and higher values of circulating load ratio.The underlying cause of this relationship was seen when comparing the ball mill feed and product size distributions from two different ball mill circuits, one with a low circulating load ratio, and one with a high circulating load ratio (Figure 3). While the F80’s and P80’s of these two circuits were close to the same, the mill feed and discharge size distributions were quite different. The ball mill in the circuit with the higher circulating load ratio contained a substantially greater fraction of material coarser than the target P80, as indicated by the respective mill feed and discharge size distributions. This fraction represents the fraction of the mill power being expended on “coarse” (in this case, plus P80 size) material, or the circuit “classification system efficiency.” The “effective mill grinding power” is the total mill power multiplied by the CSE. The compliment of CSE, the remaining fraction of “fines” in the mill, is the fraction of the mill power being wasted, and spent on over-grinding of material already finer than the circuit target product size. This is the “wasted/over-grinding mill power”"

Jan 1, 2013

By Larry G. Stolarczyk

Jan 1, 1980

By H. H. Dreissen, F. J. Fontein

The operating principle of the classifying cyclone has been described often but some special aspects of the cyclone receive further clarification here. In addition, several uses of the classifiers are summarized and made clear by means of practical examples. In coal and ore washeries, the washing cyclone is widely used for the separation by specific gravity of sizes up to about 12 mm. This application has lately been extended to the separation by specific gravity of particles up to about 50 mm. This use makes special demands on the construction and wear resistance of the cyclone. The sieve bend, a development of the Dutch State Mines which is less well known than the hydrocy-clone, is dealt with at some length. The sieve bend is an apparatus designed for wet screening. Attention is given to the variables influencing the performance of the sieve bend. Hydrocyclones are now so widely applied that it would be difficult to find an industry not, directly or indirectly, using them or knowing how to use them since publications on this subject abound.1-3,5,9-11,13-15 However, because of the large number of variables influencing the operation of classifying cyclones, it is not entirely possible to calculate the results of this type of cyclone. Therefore, a number of lesser known variables will be discussed here along with some special applications of the classifying cyclone. FACTORS INFLUENCING CYCLONE CLASSIFICATION Shape of Particles: The shape of particles may cause a much coarser classification than the one expected, considering the sieve analysis and the cyclone dimensions chosen. This was clearly shown by feeding a mixture of spheres and disks in water into a cyclone. The spheres were 0.36 mm diam and the disks, 3 mm diam and 0.03 mm thick. These dimensions were chosen in order that the disks and spheres might have the same rates of fall under gravity. Both spheres and disks had a specific gravity of 1.05. The results obtained with these particles in a cyclone are summarized in Table I. Test No. 2 shows that the catch of spheres was

Jan 1, 1963

This report is in partial fulfillment of Contract S0241051 awarded to COMINEC on June 27, 1974. 'Me purpose of the work under this contract is to develop a conceptual design for an automated longwall mining system. The conceptual design will serve as the basis for future design and development of an automated longwall mining system capable of sustained production in excess of 2,500 tons per shift with reduced manpower which will ultimately be demonstrated in an area where conventional longwall mining has been successful. 1.2 DEFINITION OF THE PROBLEM 1.2.1 Why An Automated System The most obvious benefit of automation and remote control in a longwall mining system is the reduction of accidents consequent upon a reduced working force in the hazardous face areas. However, another important aspect of the problem is the skilled labor shortage which is being compounded by the need for vastly increased coal production. The United States coal mining industry had a working force of almost 600,000 miners in 1928 but was able to muster only 145,000 miners in 1970. The miners required to staff the additional working sections and the new mines necessary to meet our energy needs are simply not available. Only automation and remote control will permit a reduced work force with increased production by keeping the face equipment operating continuously.

Jan 1, 1975

By R. W. Raymond

THE sudden death of Dr. Drown, on Nov. 17, 1904, brought to multitudes the pang of personal loss. Of all those who, as students at Lafayette College, the Massachusetts Institute of Technology and Lehigh University, were brought under his influence, not one can have forgotten him, and all will now acknowledge, with an unfading gratitude, what they owe in professional equipment to his wise, clear, skillful guidance, and in character to his sympathetic, stimulating personality. Outside of this wide circle, the experts of both hemispheres will lament the departure of one who, in his department of scientific inves¬tigation, both knew what work was needed, and how to do it so that it needed not to be done again. The older members of the American Institute of Mining Engineers will remember with gratitude the part he took, as Secretary from 1873 to 1884, in promoting the interest of that organization, and in shaping the plan and policy which it has followed with such noteworthy success. And, in addition to all these (though partly included among them), there are a host of friends; who can scarcely think of the public loss by reason of their own. Thomas Messenger Drown was born March 19, 1842, at Phil¬adelphia, Pa. His parents were natives of New England; and. he was the youngest of their three sons. He received his preliminary education in the public schools and the High School of Philadelphia, from which he was graduated in 1859. Be-

Jul 1, 1905

The Department of Mineral Resources is the lead agency in mine site environment management and control inNew South Wales. The Department introduced a Mining, Rehabilitation and Environmental Management Plan (MREMP) process several years ago in order to integrate the activities of other government agencies who may have a material interest at the mine site. The MREMP process has resulted in a spirit of trust and co-operation between agencies and between agencies and mining companies. The spirit of co-operation has been reflected in greater public confidence that mining is environmentally responsible.  

Jan 1, 1995

By D. J. Coolidge, H. L. Sheakley

THIS paper does not deal with all sands used in the glass industry in Missouri; it covers only that used in the plate-glass factory at Crystal City. However, it is probably safe to say that other sands, produced throughout the state for this purpose, are of identical nature. The glass sand used in Missouri is commonly called the St. Peter deposit, which is ascribed to the Ordovician Rock series in the form of sandstone. This St. Peter deposit, aside from a few small outliers, covers a large area of eastern Missouri. It forms, through a broad curve, the northeast margin of the typical Ozark region between Cape Girardeau on the southeast and Mineola, Montgomery County, on the northwest. The belt is extremely irregular, varying from one to ten miles in width; its length is 150 miles in a straight line. The outcrop near the entrance to the Crystal City mine appears in the form of a sandstone bluff approximately 30 ft. high, running along Plattin Creek (Fig. 1). Above the sand rock an overburden of Joachim limestone appears, which thickens to nearly 300 ft. and forms the hill commonly called Buck Knob. Test holes where drilled at various points and the drillers' log indicate that the St. Peter deposit ranges in thickness from 63 to 71 feet. PROPERTIES OF THE ST. PETER SAND From an analysis of the glass sands of the St. Peter formation in Missouri, the follow-

Jan 1, 1942

By D. Babich, L. Alcorn, E. Spencer, A. Smith

Noise is one of the most pervasive health hazards in mining. A compilation of Mine Safety and Health Administration (MSHA) noise survey data for Fiscal year 1990 shows that approximately 40% of the total samples taken for longwall occupations exceeded the Permissible Exposure Limit (PEL) of 100% [Gigliotti et al. 1991]. In order to properly determine workers’ exposures on longwall coal mining systems, it is necessary to provide accurate baseline measurements for these mining systems. This research was designed to develop guidelines and test procedures for identifying all noise sources that are major contributors to the underground noise exposure of longwall coal mining system workers. Once the high noise sources are identified, promising engineering controls can be tested and evaluated to reduce the noise of the sources. The measurement system used to analyze the noise sources included stationary dosimeters in a documented repeatable pattern and a time-motion study of the cutting cycle and operator’s work cycle. Significant results from the underground measurements show that the highest sound levels recorded are at the stageloader discharge segment and tailpiece controls and remained at about the same level throughout the test.

Jan 1, 2007

By Paul Hatmaker

Lime was a highly useful commodity thousands of years before the simple chemistry of its manufacturing process was known. The employment of lime for agriculture, building, and even certain essentially chemical purposes is so old that its origin is among the unrecorded details of man's first ventures into the manufacture and use of prepared substances. Lime is a most versatile material and consequently has come to be widely utilized in modern civilization. Immediately before the depression of the early 1930's the annual production of lime in the United States was more than 4 million tons, valued at 33 to 42 million dollars. This output was sold to many industries, so many that mere enumeration becomes tedious. In addition to agricultural and building lime the sales statistics compiled annually by the Bureau of Mines include lime sold to the steel and other metallurgical industries as refractory and fluxing material, as well as that used by paper mills, glass works, tanneries, and water-treatment plants. These major uses normally consume about 86 percent of the domestic sales. The remaining 14 percent includes lime sold for use in the manufacture of alcohol, alkalies, bleaches, calcium acetate, calcium carbide, coke gas and byproducts, glue, insecticides, oils and fats, paints, and rubber, in the refining of salt, in the manufacture of sand-lime and slag brick, in the disposal of sewage and garbage, in the manufacture of silica brick, in the refining of sugar, in the textile industries, and in wood distillation. Many other uses are also known for which complete sales data are not available.

Jan 1, 1934