Search Documents

By J. C. Stankus

To protect mine personnel and moving equipment at underground roof fall areas, mine operators typically install steel sets, which are covered with wooden blocks and backfilled with an expanding type cement material. In large roof falls, the cost of void backfilling becomes prohibitively high causing some mines to leave the voids open. However, the durability of wood over time and the capability of the steel set and wood lagging to resist falling rock are unknown. This has caused concerns for the Mine Safety and Health Administration (MSHA) and ground control engineers. During past two years, Keystone Mining Services, LLC designed and developed various impact-resistant steel set designs that were approved by MSHA and installed in various underground fall rehabilitations. This paper presents the patent pending impact-resistant steel set design methodology, including (1) steel set design per AISC national standard, (2) design, development, and laboratory testing of a water proof composite impact resistant lagging panel, and (3) impact resistant steel set design based on Law of Conservation of Energy. Two underground cases will be included detailing the application of the system.

Jan 1, 2011

By Earl Rau

Introduction Will cogeneration be a major power source in the future? The location of electric power generating plants has changed. In 1900, more than 50% of electricity was generated by industrial plants. Since then, industrial plant generation of electricity greatly decreased to 17% in 1950 and to only 3% in 1980. Changing economics in electric power generating costs, though, may allow cogeneration to reverse this trend. Cogeneration has been defined as the simultaneous production of electric (mechanical) and thermal energy from a single energy source. Some applications are considered to be byproduct generation of electricity from industrial, thermal operations. Cogeneration is not new to the mining and minerals industry. Smelters and steel mills have used waste heat to generate electricity. Public Utilities Regulatory Policies Act of 1978 The potential for increased industrial cogeneration of electricity is related to the March 9, 1978 enactment of the Public Utility Regulatory Policies Act (PURPA). The US Supreme Court ruled that PURPA is constitutional. The court upheld requirements that utilities interconnect to cogenerators. It also ruled that 100% of avoided costs be used as the guideline for electricity sales by a qualifying facility (QF) to a utility. The state of New York established a floor price $0.06/kWh for electricity sales from a QF to a utility. It is obvious, then, that a cogenerator must first establish price and then become a qualifying facility in order to sell electricity to a utility. Proposed cogeneration plants The estimated industrial cogeneration potential for the years 1986 to 2000 is 9500 to 25,000 MW. Industries represented in this cogeneration estimate are pulp and paper, petroleum, chemicals, food, textiles, rubber, plastics, steel, lumber and wood, cement, glass, metal fabrication, and industrial parks. A cogeneration plant has been proposed for the Union Carbide chemical plant in Institute, WV. A steam turbine/generator would be installed to replace the pressure-reducing valve in the 2.7 MPa (400 psig) header. Scott Paper Co., Mobile, AL, proposed a cogeneration plant using a coal- and wood-fired boiler and a turbine/generator to produce process steam and electric power. A cogeneration system has been proposed for a large oil refining plant. A pulverized coal boiler would produce high-pressure steam to operate a turbine, generator. The exhaust steam from the turbine will go to the process and an existing turbine. Kansas City, MO's Armour meat-processing plant has proposed a cogeneration plant. This proposal is to use a natural gas or oil-fired, gas-driven turbine and a generator. The waste heat from the gas turbine would go to a heat recovery boiler for use as process heat. Dade County, FL is implementing a central energy system to supply electricity, air conditioning, and domestic hot water for five buildings in downtown Miami. The cogeneration system is to provide flexibility, to optimize fuel use efficiency while serving the variable thermal demands. Generation of electricity from municipal waste is not considered to be a cogeneration process but is covered by PURPA. Special considerations are provided for waste/electric power generation to encourage the development of these systems. ?

Jan 7, 1987

By A. C. Fieldner

This report is the fourth of a series of annual summaries of research and technologic work on coal by the Technologic Branch of the Bureau of Mines. The coal research program of the Bureau has been broadened and made more flexible to adapt it to changing conditions and needs of the coal industry, and as a result information as to the properties and composition of coal has been increased and new and improved practices in mining, preparation, and utilization of coal have been devised. The present

Jan 1, 1940

By Carlos A. Barrena Chávez

El presente trabajo señala una variación en la preparación del Under Cut como método de Explotación Sub Level Stopping 3 en la mina Iván -en tanto es usado como subnivel para el reconocimiento, perforación radial y ventana de extracción durante el proceso productivo. El desarrollo de este método contempla una rampa principal de acceso, desde donde se realiza el trabajo de preparación de la cámara para su posterior explotación.De otro lado, se resalta la importancia del estudio geomecánico para el dimensionamiento de la cámara y la secuencia de explotación en el planeamiento de minado.

Sep 12, 2005

By J. Wasmund Concha

En los últimos años la innovación en la industria minera viene tomando cada vez mayor importancia puesto que será una necesidad para desarrollar proyectos económicamente atractivos. Dentro de ella un nuevo tipo de flotación viene ganando cada vez mayor importancia, nos referimos a la Flotación de Partículas Gruesas (FPG), es decir partículas mayores a 150µm y hasta 850µm. Se estima que para proyectos brownfield este tipo de flotación podría permitir ampliar la capacidad de planta hasta en un 25% solamente implementando el sistema de FPG, y sin la necesidad de instalar más molinos.

Sep 1, 2017

By H. M. Thorne

The Petroleum Experiment Station of the Bureau of Mines at Laramie, Wyo., in cooperation with the University of Wyoming, has in progress chemical and refining studies of Wyoming black oils. In general, these crude oils are characterized by their high sulphur, high asphalt, and low gasoline content and are called black oils because of these properties and their color. Characteristics of the various Wyoming black crude oils, as determined by the Bureau of Mines Hempel method of analysis, have been published.4/

Jan 1, 1938

By H. M. Thorne

The Petroleum Experiment Station of the Bureau of Mines at Laramie, Wyo., in cooperation with the University of Wyoming, has in progress chemical and refining studies of Wyoming black oils. In general, these crude oils are characterized by their high sulphur, high asphalt, and low gasoline content and are called black oils because of these properties and their color. Characteristics of the various Wyoming black crude oils, as determined by the Bureau of Mines Hempel method of analysis, have been pubished.4/

Jan 1, 1938

By Sudhir Kumar Kashyap

In underground activities ground control is a challenging problem. It affects safety, production, and efficiency. As per statistics of accident data, ?fall of roof/sides? is one of the major causes of mine accidents. In many cases, our experiences and understanding of soil and rock behavior still fall short of being able to predict how the ground will behave. Presently, empirical approaches to design are widely used in estimating mine support parameters. Under these circumstances, expert judgment plays an important role, and such accidents can be obviated with accurate measurement and optimization of data and analysis using the neuro-fuzzy technique of artificial intelligence. Recently, a neuro-fuzzy hybrid approach has become one of the major areas of interest in engineering fields because it gets the benefits of neural networks as well as those of fuzzy logic systems, and it removes the individual disadvantages by combining them on the common features. Neural network and fuzzy logic technologies have common features, such as a distributed representation of knowledge, the ability to handle data with uncertainty and imprecision, etc., like in ground control. Fuzzy logic technique has tolerance for imprecision of data, while neural networks have tolerance for noisy data. In this paper we have focused an intelligent technique, i.e., neuro-fuzzy technique, to approximate the setting load given to the standing support (props) erected for the purpose of supporting freshly exposed roof during underground mining. We have used twelve input variables of rock parameters, and after having trained using a neural network with a sigmoidal function as an activation function, simulation was done to find the output parameter, i.e., the pre-load (setting load)to be applied on props. Outputs of the neural network were again fed to the fuzzy system together with the twelve parameters, incorporating five triangular membership functions for each parameter. Final optimum output was approximated using the MATLAB program, which was found to be satisfactory. Neuro-fuzzy technique has better performance over individual neural networks or fuzzy logic technique.

Jan 1, 2012

By Parry. V. F.

"INTRODUCTION Coal is a compressed mass of heterogeneous, macerated, metamorphosed plant remains that have collected in the earth's crust. Probably no two beds of coal have identical properties, and different parts of the same bed may vary considerably when measured by some of the many empirical tests that have been developed to classify or differentiate the properties of coal. Because of this great variability in properties, the commercial processing of coal to produce coke and byproducts has developed largely as an art based on experience, rather than as a science. Much empirical chemical research, however, has been and is being conducted on coal carbonization, and this work is of practical value in obtaining larger yields of gas and byproducts and in the improvement of the physical properties of the coke.Both ultimate and proximate analyses have been used for correlating purposes. 3/ In the United States the proximate analysis is used for the classification of coal according to rank and grade. The proximate analysis can be employed usefully in the coal—carbonization industry because separation of the combustible matter of coal into volatile matter and fixed carbon is, in fact, a small carbonization test conducted on 1 gram of coal heated in a platinum crucible.Small—Scale Laboratory Coking Tests,Many empirical tests have been devised for determining the coking properties and measuring the yield and quality of gas and byproducts obtainable from various coals. These tests, made on samples ranging from 25 grams (about 1 ounce) to 5 kilograms (11 pounds), furnish information that is roughly proportional in practical value to the size of the sample carbonized. However, the cost of the carbonization test also increases with the amount of the sample, so that for preliminary surveys of a number of coals, samples of 25 to 1,000 grams usually are employed."

Dec 1, 1939

By M. Mahan, D. D. Blue, O. C. Garst, F. Fraas, L. Fink

"Early in World War II it became apparent that the known bauxite re- serves might not be adequate to supply the demands of the American aluminum-producing industry, as the transportation of bauxite from abroad to this country might easily be interfered with by hostile action. Consequently, the Bureau of Mines set up an intensive, well-integrated program for the production of cell-grade alumina from low-grade domestic ores. This pro-gram of investigation covered the production of alumina from clay, alumite, red mud, and other low- and marginal-grade ores. In line with the Bureau's usual policy of conservation of natural resources, it was decided that the investigation should be extended to cover the production of alumina and other valuable byproducts from aluminum dross.Statistical information showed that during the year 1943-44, an average of 2,900 tons of aluminum dross was generated monthly. This dross, after partial removal of free metal, had an average metallic aluminum content of approximately 9 percent. Some of this dross was produced by the melting of alloyed aluminum; but a large proportion 1,700 out of 2,900 tons - was generated by two producers of primary aluminum, and the dross did not contain an great proportion of alloying metals. Compared with dross from other sources, this 60 percent of the country's capacity can be assumed to have relatively uniform composition. Moreovcr, the problem of collection and distribution can be minimized because of the relatively small number of plants included in the organization of these two producers of virgin metal.Except for large pieces of metallic aluminum that easily can be mechanically separated for remelting, this dross has been discarded and scrapped. Inasmuch as chemical analyses show that the alumina content of dross is far higher-than ordinary ores - 111 percent alumina equivalent in dross compared to 57 percent alumina in bauxite - aluminum dross is a far richer source of aluminum than any known naturally occurring ores. The discard, of this waste material during the war and reconversion periods would be unsound economically. The work reported herein describes tests at the College Park Station of the Bureau of Mines on the recovery of metal, alumina, ammonia, methane, and abrasive-grade corundum from dross."

May 1, 1946

By R. V. Norris

The great coal strike of 1902, which confined the work at the Short Mountain colliery of the Lykens Valley Coal Com pany almost exclusively to pumping, gave an opportunity to determine with considerable accuracy the cost of pumping the water from these very old, extensive and wet mines. This colliery, which is located in the extreme southwestern end of the anthracite coal-field, has been operated continuously since 1836, and has shipped 7,747,313 tons of coal. This and the Williamstown colliery are the only operations in Dauphin county. The workings cover about 5 miles along the North dip of the extreme westerly end of the basin, with the operating slopes near the center. They extend around the westerly spoon of the basin and back about 31/4 miles easterly on the South dip. The mines are very deep, the present workings ex tending to 711 ft. below sea-level, and about 1600 ft. below the lowest surface-opening. The coal is hoisted principally from the Short Mountain slope, which is 1550 ft. long, with 26 to 68 degrees dip, and from an inside slope, No. 4, 800 ft. long, with 52 to 72 degrees dip. The ordinary capacity of the colliery is about 1000 tons per day, and the average output for the years 1897 to 1901, in clusive, was 297,000 tons per year. The seams worked are the lowest Red Ash measures, being, respectively, Nos. I, II and III of the coal-bed series, but locally called the " Little Lykens," " Lykens," and " Whites." On the accompanying plan the Lykens seam is shown in full and the Whites in dotted lines. The pumping-plant is divided into four lifts, the pumps being located as shown in the section, Fig. 1, and the plan, Fig. 2.

Jan 1, 1904

By Werner Burger

Earth Pressure tunnel boring machines are tackling difficult ground conditions that five years previous were not considered feasible. The technology has evolved that allows EPB TBMs to cross into areas that with the latest in conditioning and special design considerations are now possible to mine. This paper will review the various recent developments and those projects where these new techniques have been applied.

Jan 1, 2008

By B B. Du, Y N. Lu, L X. Wang, S L. Wu

The cohesive zone in the blast furnace is largely affected by the softening and melting behaviour of ferrous burden because of its vital role in the blast furnace process. The Visual High Temperature Methodology (VHTM) has been given to study the softening and melting behaviour of sinter, two kinds of lump ores and acid pellet intuitively. Before softening, both two kinds of lump ore swelled and more serious for lump ore B because of its denser structure than lump ore A. The softening and melting temperature intervals are different from one another and this phenomenon contributed to the gas permeability of ore layer in the cohesive zone since the ‘ore window’ has formed. Besides, the softening and melting behaviour of mixed burdens have been studied, where it has been found that the softening and melting characteristics of mixed burden A (consisting of sinter and lump ore A) is better than mixed burden B (consisting of sinter and lump ore B) and mixed burden C (consisting of sinter and acid pellet) despite the poorest characteristics of lump ore A. The reason is that the high temperature interactivity between lump ore A and sinter is much better than lump ore B and acid pellet. The high temperature interactivity is mainly influenced by the chemical compositions, porosity and contact condition. This paper provides a new research method for the softening and melting behaviour of iron ore and an important technical basis for the optimisation of blast furnace burden.CITATION:Wang, L X, Wu, S L, Lu, Y N and Du, B B, 2017. The softening and melting behaviour of single and mixed iron ore burdens, in Proceedings Iron Ore 2017, pp 605–610 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By C. E. McManus

MANY mechanical advances have been made on mining equipment during the year 1951. There have been a number of trends established and many modifications made on open-pit equipment to increase the efficiency and availability of all the machines necessary in the moving of overburden and iron ore. Some years ago, the trend toward larger shovels for the loading of off-highway trucks began, but in the last year, it has become general practice to use the 5 to 7 ¼ -yd quarry-type shovels in the loading of haulage units. For years these larger shovels were used in the locomotive haulage pits. As the truck capacities increased from 15 to 20 to 30 tons, the need for larger loading units became apparent. Today in most mines, large shovels are in evidence and a few 8-yd shovels will be delivered this year for loading off-highway trucks. Torque Converter-Shovel The Diesel-driven shovel with its friction bands has been modernized with the torque converter. There have been about ten shovels remodeled to take a torque converter in the drive system. The large high-torque, low-speed Diesel engine was removed and replaced by a high-horsepower, high-speed, automotive-type engine. This engine was connected directly to the torque converter. The torque converter was connected to the shovel through the standard original sprocket and chain. Dual governors controlled engine performance. One governor controlled the high idle of the engine; the other governor, which is connected through a flexible shaft to the output shaft of the converter, controlled the loading of the engine. With this dual governor hook-up, the engine anticipates load conditions and is operating at high idle and full throttle before the shovel load is transmitted back through the converter to the flywheel. It has been found that with this automotive-type engine and converter, the shovel capacity has been increased about 20 pct. Also, the wear on the friction bands, breakage of hoist cables, and other mechanical breakages has been reduced materially. Alloy-Steel in Shovels The shovel equipment manufacturers have been experimenting with low-temperature-strength, high-alloy steels to combat the excessive breakage that occurs in extremely cold weather. High-nickel alloy steel has been used in critical areas that are affected by low temperatures, the most notable being dipper sticks. Most shovels ordered today are equipped with some of this special, alloy steel. More and more manganese alloy is being used for replacement parts such as shovel pads, idlers, drive sprockets, etc. Although the initial cost of these parts is considerably higher than the standard replacement items, the life of these manganese parts is considerably longer and well worth the added expenditure. Dipper-teeth repair is still a problem. Most companies use the small replaceable inserted tooth. It has become common practice among some of the companies to "job out" their dipper-tooth repairs to outside welding companies. This necessitates an additional inventory of teeth, but it does guarantee an adequate supply of replacement teeth at all times. These contractors have set up their shops on a production basis and can do an acceptable job at a high rate of speed. Thermite welding has been used in retipping teeth. To date, the process cannot be called successful but with improvements the time required to repoint the dipper teeth will be decreased considerably. The submerged arc process has been tried in the replacement of these dipper points, but like thermite welding has not proven successful. Here again, if a method can be developed to use submerged arc, the job of teeth repair will be made much easier. New model shovels in 6 ½ and 8 cu yd sizes fea-

Jan 1, 1952

The National Institute for Occupational Safety and Health (NIOSH), in partnership with stakeholders in the mining and surface drilling industries, con-ducted research to develop engineering control technologies that reduce workplace noise exposure. The result of this research partnership is the development of a partial cab.

Jan 8, 2007

The Electrolytic Refining and Smelting Company of Australia Limited (ER&S) operates a copper smelting and refining plant and is situated close to the heart of the highly industrialised area of Port Kembla. In March, 1982 the Company entered into an undertaking with the State Pollution Control Commission (SPCC) to monitor ambient levels of sulphur dioxide (S02) gases present in the atmosphere in the surrounding urban area. Despite the use of a 200 metre high stack for dispersal of the smelter waste gas stream at ER&S, two local suburbs, Warrawong and Primbee were experiencing on occasions high ambient concentrations of S02 resulting in discomfort to local residents. In late March 1982, ER&S installed a highly advanced S02 monitoring system to continuously monitor the levels at Warrawong. The system was extended to include S02 monitoring at Primbee in November 1982, and further extended in June 1983, to include an input of meteorological data. Initially the system was designed to monitor and react to high concentrations of S02 at either of the two monitoring stations. Currently however, refinement is taking place to allow a predictive nature to be built into the system such that it not only reacts to an adverse situation but can predict weather patterns likely to cause high concentrations and thus avoid these events. The entire system is still undergoing a growth and development period, however the results obtained to date are pleasing to both the Company and the SPCC.

Jan 1, 1984

By Godofredo F. Barrios

For years urethane screen surfaces have been used in a wide range of wet screening applications where openings from as fine as 100 microns and coarser have been used. The purpose of this paper is to expose the reader to new developments in both screen surface and screening equipment technologies which allow an end user to consider urethane screen surfaces for fine screening applications. These technologies allow an end user to use the inherent advantages of urethane with regards to wear resistance while also realizing the benefits that a high oper area urethane screen surface can bring. These benefits include non blinding characteristics and feed capacities that which rival that of traditional stainless steel surfaces. The paper will highlight the features of this patented urethane screen surface technology and the screening machines they are used in conjunction with. There will also be a presentation of case studies of commercial installations where these technologies are utilized. These case studies are from the base metals industry therefore relevance to the conference is direct and not inferred. Included in the paper will also be constraints which must be taken into account when considering urethane screen surfaces such as temperature and chemical attacks. This paper will expose potential end users to a possibility of using screens to achieve extremely accurate size separations in applications where screens were previously not considered. The paper will explain and demonstrate that prior concerns of screen surface blinding, high screen surface consumption rates and large screen surface area requirements can be eliminated by proper utilization of high open area urethane screen surfaces.

Jan 1, 2007

By B. J. Moore

This publication contains routine analyses and related source data for 547 natural gas samples from 22 States and three foreign countries. Of this total, 340 samples were collected during calendar year 1967. The remaining 207 analyses are of samples collected during previous years, but releases granting, permission to publish the results were not received until 1967. All samples were collected as a part of a continuous survey of the free world for occurrences of helium in natural gas. The Bureau of Mines has conducted this survey in the United States since 1917, and in 1965 it was expanded to include foreign gasfields. The analyses published herein were made by mass spectrometer and a special helium analysis apparatus which are described in Bureau of Mines Bulletins 4863 and 516.4 Nine previous publications have been made to present results of 7,618 gas analyses made by the Bureau of Mines Helium Activity prior to 1967. The first three, Bulletins 486,5 576,6 and 6177 contain analyses and related source data on 5,218 gas samples collected from 1917 through 1960. The other six

Jan 1, 1968

By R. S. Simkus, J. R. Egan

"Changes have recently been applied to the Sullivan Concentrator lead and zinc circuits to treat fine-grained ores which make-up the majority of ore reserves in the mine. Pilot plant test work conducted in 1990-91 indicated that concentrate grades would be substantially improved by reducing the particle size (P,0) of the lead from 38 to 15 µm and the zinc from 45 to 24 µm.Circuit revisions involved installation of major new equipment including: two GUO kilowatt Vertimills for regrinding, a 4 metre diameter column flotation cell and a 4 metre diameter hyperbaric pressure filter for dewatering. Duties of the existing regrind mills were reassigned.IntroductionThe Sullivan ore body is a massive sulphide deposit consisting of fine grained mixtures of sulphides, sometimes inter-banded with country rock and varying widely in their content of lead, zinc, iron and silicates. Principal economic minerals are marmatite and galena. Iron is mainly present as pyrrhotite (85%), and to a lesser extent as pyrite (15%) .The orebody has been actively mined since 1923, with 1992 ore reserves estimated at 15,800,000 tonnes with an average grade of 4. 7% lead and 7. 9% zinc. Current plans call for treatment of 1,600,000 tonnes/year, (7,000 tonnes per operating day), with flotation feed grades of 5.9% lead, 10.1% zinc, and 22.0% iron."

Jan 1, 1994

By Jorge James

En los últimos 20 años la conflictividad social alrededor de las minas y proyectos mineros ha aumentado debido a diferentes razones. Haciendo un análisis de los conflictos se pueden extraer lecciones que sirvan a las empresas mineras para evitar, o al menos mitigar, conflictos futuros. Esta lista de 50 lecciones puede servir como una guía de lo que hay que hacer, de lo que hay que evitar, o por lo menos de qué temas se deben tomar en cuenta al momento de desarrollar un proyecto minero.

May 10, 2023