Search Documents

By Donald Gagnon

El presente trabajo señala el proceso de sostenimiento de terrenos en las minas subterráneas a través del estudio de las condiciones geológicas subterráneas del área, con el fin de establecer distintos tipos de rocas que garanticen la instalación adecuada de las fortificaciones. Asimismo se describen las características y propiedades físicas de los difentes tipos de rocas, como el uso de los distintos pernos para el sostenimiento de roca y sus técnicas de instalación.

Oct 6, 1999

By Jérôme Boutin, Rémy Oddo, Sylvain Ouellette, Paul-Émile Boileau, Gilles LeBlanc, Pierre Marcotte

ackleg rock drills are widely used in the mining industry and are known to generate high levels of hand-arm vibration which contribute to the development of the hand-arm vibration syndrome for exposed miners.1-3 To reduce the vibration levels, a prototype of an antivibration handle was developed as part of a previous study.4 To provide some bench marking for this handle prototype and to follow the evolution of its performance over time, a test bench was developed to characterize the vibration emission values of jackleg drills under controlled operating conditions. As the current ISO 8662 series of standards could not apply directly to this type of tool, there was a need to design and validate a test bench to evaluate the vibration emission values of jackleg drills, while taking into account the conditions specific to the operation of this type of tool. Methods A test bench including an energy absorber, was developed for testing jackleg drills based on the ISO 8662-3 standard 5. The energy absorber was bolted to a 3300 kg concrete block to ensure tool stability. A pictorial view of the device is given in Figure 1. For validation purposes, acceleration measurements at the handle of a conventional jackleg drill were taken simultaneously along the three axes (xh, yh and zh) in an underground rock drilling operation as well as on the test bench. The handle accelerations were measured for three different jackleg angles (13º, 28º and 43º) determined with respect to the floor. Moreover, each measurement was repeated at least three times to asses the data repeatability. [ ] Results As a preliminary validation of the test bench, Figure 2 provides a comparison of the frequency weighted rms acceleration spectrum measured along the zh-axis, for both underground drilling and operation on the test bench (28º jackleg angle in both cases). It is shown that the vibration measured on the handle of a jackleg drill operating on the test bench is representative of that recorded during typical rock drilling operations, despite the fact that some harmonics of the percussion frequencies are generated with a higher amplitude on the test bench. Table 1 provides

Jan 6, 2006

By M R. Stevens, W Mori, G B. Boswell

The Onemana prospect is located on the eastern Coromandel Peninsula, North Island, New Zealand. Systematic exploration involving surface geological mapping, geophysics, rock and soil geochemistry, reverse-circulation and diamond drilling has identified a number of important features of a fossil hydrothermal system at Onemana. This relatively intact gold mineralised system is hosted within a sequence of rhyolitic volcanics and volcaniclastics, overlain by lake sediments, sinters and hydrothermal eruption breccia. The system lies within a graben/half graben bounded by major NE-trending faults which form the approximate boundaries to hydrothermal alteration. Rock and soil geochemistry indicate a broad zone of anomalous gold, silver, arsenic, mercury and antimony. Overlapping elevated rock and soil gold anomalies indicate strongest mineralisation occurs over two zones of hydrothermal brecciation named 'Breccia Knob' and 'Western Ridge'. Geophysical data obtained from Gradient Array Resistivity and Ground Magnetics have been used to produce anomaly maps. The terrain corrected resistivity plot shows a number of well defined linear resistivity anomalies which are believed to represent large silicified and quartz veined bodies at relatively shallow depths. The strongest of these anomalies correspond with 'Breccia Knob' and 'Western Ridge'. Reverse-circulation and diamond drilling targeting these resistivity and geochemical anomalies has confirmed wide intervals of quartz veining, silicification and gold mineralisation. Petrologic data based on drill samples indicates the existence of a laterally extensive gold bearing epithermal system. Hydrothermal alteration is thought to have been caused by strongly convecting, two-phase (boiling), near-neutral chloride fluids which persisted at high temperatures (170 - 220¦C) to the paleosurface. A geological model is postulated of a large, complex, hydrothermal system developed in a shallow lake or marginal lake environment created by rifting and graben development within a recently extinct rhyolitic volcanic centre. Geothermal activity alternated between relatively quiescent periods of unrestricted fluid upflow and sinter development interspersed with violent hydrothermal eruptions caused by near surface silica capping and overpressuring above a major fluid conduit centred under 'Breccia Knob'.  Opportunities for precious metal mineralisation are evident from drilling to date. Upflow of near-neutral chloride fluids to shallow depths favours the presence of strongly mineralised stockworks at relatively shallow depths. Periodic hydrothermal eruptions would have caused fracturing and rapid depressurisation of the hydrothermal system, strongly favouring the precipitation of gold from solution both near surface and within feeder-vein systems at depth.

Jan 1, 1995

By H. John Head, Fred N. Kissell

In This Chapter [Gas reports from around the world Regulations for gassy mines in the United States Differences between metal/nonmetal mines and coal mines Monitoring for methane and taking action Diluting methane with additional ventilation Eliminating ignition sources What experienced mine operators say about methane control and Looking for methane when starting a new mine or expanding an existing mine] This chapter gives guidelines for preventing methane gas explosions during metal and nonmetal mine development and subsequent production operations.3 Emphasis is placed on recognizing the differences between coal mines, where the potential for methane hazards is relatively well understood, and metal/nonmetal mines, where methane may accumulate unexpectedly. Also, interviews with experienced mine operators add much to a complete understanding of what must be done to address methane problems in metal/nonmetal mines. METHANE GAS IN METAL/NONMETAL MINES Gas reports from around the world. The presence of methane gas in metal/nonmetal mines around the world is more common than one might imagine [Edwards and Durucan 1991]. For example: • The former Soviet republics have occurrences of methane and hydrogen in apatite, gold, and diamond ores, where solid or liquid bitumen occurs in the rock. • Scandinavian iron ore deposits include methane and other hydrocarbons in boreholes that intersect pitch and asphalt within the deposits, and methane and nitrogen in boreholes and fissures in arsenic and sulfide ores.

Jan 6, 2006

By Donald J. Hallbom

"While pipeline hydrotransport is often the most economical way to transport large volumes of mineral concentrate, tailings, or fine ore slurry over long distances, it is in mountainous terrain that pipelining becomes particularly attractive. These areas are often remote, with limited existing infrastructure and few potential users willing to share in the cost of new infrastructure. The rugged terrain makes the construction of railways or roads suitable for haul trucks difficult and expensive. The elevation difference between the mine and the terminal means that the empty trains or haul trucks need to return up-hill, resulting in high fuel costs. With pipelines, this elevation difference may reduce or even eliminate the need for pumping. As a result, numerous pipelines have been built, or are being considered, in mountainous regions around the world including: Tasmania, New Guinea, China, Madagascar, the Rockies of North America, and the Andes of South America. However, there are technical difficulties that need to be overcome in the design and operation of mountain pipelines that do not affect pipelines on more level terrain. This presentation reviews some of these difficulties and methods used to overcome them.INTRODUCTIONPipeline transport of solid-liquid slurry (“hydrotransport”) is an important and cost-effective means of transporting large volumes of solids over long distances, especially from a single supplier to a single user (e.g., a concentrator to a port, a concentrator to a tailings dam, or a coal mine to a power plant). Pipelines are generally found to be more economically attractive than alternate transportation methods (e.g. trucking, rail, conveyors, shipping, or some combination) over the life of a project (Aude et al. 1974).Hydrotransport systems have been built in a variety of terrains, but it is in mountainous regions that pipelining becomes particularly attractive. These regions are often remote and generally do not have existing transportation infrastructure (roads, railways, navigable rivers). There are few potential users (e.g., farmers, other mines, forestry companies, etc.) who may be willing to share in the cost of new infrastructure. The rugged terrain makes the construction and maintenance of railways or all weather roads suitable for large haul trucks difficult and expensive. Mines tend to be higher than the receiving terminal (e.g. a port). This means that the empty trains or haul trucks need to return up-hill, resulting in high fuel costs. With pipelines, this elevation difference may reduce or even eliminate the need for pumping. Pipelines are easier to construct than roads and railroads in these areas for several reasons, including:"

Jan 1, 2006

By S. Kahraman, K. Develi, E. Yasar

Four hydraulic top hammers, one pneumatic top hammer, and three down-the-hole drills were observed in several rock types at quarries and highway construction sites to measure the performance data. At the same time, drill cuttings from each drill hole were collected for the determination of the coarseness index (CI), which is the sum of cumulative weight percentages of a particular size-graded sample of debris, and for the determination of median particle size (MPS), which is defined as the particle for which the quantity of particles equals 50% of the total of the cumulative distribution. After the sieve analysis was carried out on the drill cuttings in the laboratory, CI values were calculated and MPS values were obtained from the plots of cumulative undersize vs particle size. The performance data of the drills, CI values, and MPS values were analyzed using the least square regression method. It was seen that strong linear relationships usually exist between penetration rates and CI values, and penetration rates and MPS values for both top hammer drills and down-the-hole drills. Penetration rates increase linearly when increasing the CI and MPS values.

Jan 1, 2004

By Paul Hughes

This paper summarizes current underhand paste backfill mining as applied to Goldcorp Inc?s Red Lake Mine, Newcrest Mining Ltd?s Kencana Mine and the Lanfranchi Nickel Mine as well as ongoing research at the University of British Columbia?s Norman B. Keevil Institute of Mining Engineering. The Red Lake Mine utilises a 6 m wide undercut with a 2 MPa unconfined strength paste in order to selectively mine its high grade, high-stress orebody. Kencana?s orebody is located in a poor rock mass environment. An 8 m wide, 2 MPa unconfined strength paste sill allows a safe working condition for its high grade orebody. The Lanfranchi Nickel Mine utilises a cable-supported, 2 MPa paste, with 12 m span sills, to optimize the mining of the squeezing rock mass. This paper details the rock mechanic hazards, ground support techniques, paste practices and unique conditions for each mine. Further, an update of ongoing research at the University of British Columbia, focussing on the optimization of safe mining in underhand cut-and-fill mining in high-stress/weak rock masses, is presented.

May 1, 2011

By Jorge Tramaglia

En la naturaleza existe elementos radioactivos naturales conocidos por las siglaS NORM ( naturally occurring radioactive material) que desde su origen en el reservorio, se movilizan acompañando al petróleo hasta las instalaciones de proceso en superficie. En ese sentido, el presente texto señala la radioactvidad de esto materiales, transporte y acumulación, procesos de separación, valores de contaminación, las formas de irradiación y la espectometría.

May 1, 2015

By K. Viking

This article deals with some of the civil engineering related problems to be encountered when offshore wind energy projects transform from prototype offshore wind energy converter farms, developed and installed during the 1990's, to commercial farms that's currently planned to be built. The offshore wind energy converter (OWEC) installations encounter a wide range of problems, only partial of these are geotechnical. In Europe both onshore and offshore wind farms have, from a historical point of view, usually been founded by using the monopole technique, installed with traditional impact hammers, or by using gravitational foundations. However, the rapid development of bigger turbines and larger wind farms, together with increasing considerations of fatigue aspects, has lead to financial benefits of developing and exploring other foundation techniques. This paper reviews some Scandinavian experiences regarding critical components of the design phase in relation to connecting the superstructure to the ground, and some of the main considerations of how the loads applied to the structure are transferred to the surrounding soil. Keywords: Offshore Wind Turbines, Wind Farms, Foundation, Pile, Gravity Structures

Jan 1, 2005

By David Estrella, Hector M. Lizama, Jhonny Carrión

"Microcel™ sparging systems were installed on one column of the molybdenum cleaner circuit and one column of the copper first cleaner circuit at Antamina. The Microcel™ system is known to generate finer bubbles than jetting-type spargers, and smaller bubbles have been associated with higher recoveries in flotation. Alternating tests were carried out on the molybdenum column, using either jetting-type spargers or the Microcel™ system. Experimental conditions of gas flow rate, wash water rate, and froth depth were tested. Use of Microcel™ decreased the bubble sizes from 2.6-2.9 mm to 1.5-2.0 mm. In addition, Microcel™ improved both unit molybdenum recovery and unit molybdenum concentrate grade. In the copper first cleaner circuit, side by side tests were carried out that compared the Microcel™ column with a parallel columns fitted with jetting-type spargers. Best results were obtained at manifold pressures of 260-290 kPa, where bubble sizes of 1.6-2.6 mm were observed. In either copper or molybdenum flotation, the Microcel™ system required only 50-60% of the gas flow used by jetting-type spargers.INTRODUCTIONAntamina is a copper-zinc mine located in the Peruvian Andes. Compañía Minera Antamina is owned by BHP Billiton (33.75%), Xstrata (33.75%), Teck Cominco (22.5%), and Mitsubishi (10%). The mine was commissioned in 2001 with a capital investment of US$2.3 billion, and has a nominal 100,000 t/d mill capacity. Mining, milling, flotation, and tailings impoundment take place at the mine site, which sits at an altitude of 4,300 m above sea level. The deposit is a polymetallic skarn ore body with intrusive phases of quartz-monzonite porphyry into Cretaceous aged limestone [Evans et al, 2005]. Ore body thickness is 100 to 150 m and has the shape of a flat-lying crescent. Copper is present mainly as chalcopyrite with a minor bornite component. Zinc is present as sphalerite. Molybdenum is present as molybdenite. Some lead, bismuth, and silver are associated with the sulphides. The deposit is currently classified into six main ore types [Dechert, 2006], grouped into two categories: copper and copper-zinc. The mill produces four concentrate types: copper, molybdenum, zinc, and lead-bismuth. Copper, zinc, and lead-bismuth concentrates are transported by pipeline down to the port of Huarmey. Molybdenum concentrates are bagged and trucked to port."

Jan 1, 2008

By B. Samanta

A quality characteristic analysed through construction of the Shewhart control chart is required to be normally distributed. In mining applications, this assumption is often violated as many quality characteristics follow skewed or lognormal distribution. In this paper, two methods were investigated using a heuristic approach for setting up the control limits for a skewed population. Based on these approaches a Mode chart, and a Weighted Variance (WV) control charts were constructed. The performance of the proposed methods was compared with the normal based Shewhart method through a case study conducted in a surface mine supplying iron ore to a steel plant. A simulation study was also conducted to evaluate the effectiveness of the proposed methods over the Shewhart method. The study revealed that the Shewhart control charts generated more out of control alarms compared with the Mode and Weighted Variance control charts for a skewed population of Fe%. The simulation results also revealed that for extremely high skewed population, the WV control chart and Mode control chart provided higher probability of coverage than the Shewhart method; although the detection rate (probability of detection) of out of control condition for these methods was slightly reduced compared with Shewhart method.

Jan 1, 2004

By L. Hoffman, F. Seymour, S. Hoerger

Newmont has a large integrated operation in Northern Nevada with numerous mines, stockpiles, and processing facilities. There are over ninety defined metallurgical ore types and over sixty defined gold recovery process options. To take better advantage of the available synergies, a complete Nevada wide mine plan and process model along with a mixed Integer and Linear Programming optimization tool has been developed and implemented. This system is maintained and operated by a Nevada Planning Group. Standard in-house planning software tools and methods have been implemented at all mine sites. While increasing the effectiveness of planning in Nevada, these changes have allowed a significant reduction in overall Mine Engineering staff.

Jan 1, 1999

Plant survey data has shown that gold recovery through a specific copper concentrator was significantly lower than copper recovery. Size-by-size analysis revealed that this was due to poor recovery of+75 µm and ?23 µm gold containing particles. In order to further investigate the nature of the gold losses, experiments were conducted at laboratory scale. Gold deportment studies on the laboratory flotation products revealed that coarse gold (+75 µm) reporting to the rougher tailing was predominantly associated with non-sulphide gangue. Further grinding of the plant rougher tailing improved recovery of gold and copper, while not affecting iron recovery, due to improved liberation of gold from non-sulphide gangue in coarse size fractions. EDTA extraction to remove surface contaminants showed a similar improvement for fine, liberated gold flotation.

Jan 1, 2003

By J. -L. Briaud

This presentation shows the results of laboratory and field tests to date for the NCHRP project entitled "Downdrag on Bitumen-coated Piles". This project required to test a variety of bitumens in the laboratory to determine their properties and then to establish a field testing program to verify the bitumens effectiveness. Figure 1 shows an organizational chart that gives an overview of the agencies involved in the project. The first part describes the laboratory testing program in which bitumen samples of various types were obtained from a variety of manufacturers. Initially, classification tests were performed to verify the manufacturers' specifications. Additional tests were then developed and performed to determine the bitumens behavior under the various conditions that they may be exposed to in the field. The test results were analyzed and their usefulness for design purposes were determined. The test results are presented in either graphical or tabular form. The second part describes the field testing program which was designed to test the effectiveness of various bitumens under a wide range of soil, temperature, and construction conditions. The first site was in Edmonton, Alberta, Canada, where a construction project was to take place in the winter of 1989-90. This was ideal for the cold temperature extreme that was needed. The soil conditions were conducive to downdrag problems: an embankment placed over soft clay underlain by dense sand resulting in end-bearing piles. The other site was in New Orleans, Louisiana. The part of the project involving this downdrag study was to be carried out in the summer of 1990. The hot summer temperatures and extremely soft soil conditions (resulting in friction piles) gave the other extreme needed for this study. Each site is discussed in

Jan 1, 1991

A bearing isolator is a noncontact, nonwearing, permanent bearing protection device. It has a rotor and a stator, and the two are unitized, so that they do not separate from one another while in use. The rotor turns with a rotating shaft, while the stator is pressed into a bearing housing. The two components interact to keep contamination out of the bearing enclosure and the lubricant in. Bearing isolators do not require lubrication or any particular shaft finish or condition. The best bearing isolators are made of metal, usually bronze. They use a vapor-blocking feature that inhibits the free transfer of vapor contamination when the rotating equipment is cycled on and off.

Jan 1, 2004

By W. W. Adams, T. D. Lawrence, D. R. White

"This paper presents the results of the eleventh yearly accident-prevention contest, the National Safety Competition of 1935, conducted by the United States Bureau of Mines. Participating in the competition were 336 mines and Quarries in 37 States. Five mining or quarrying companies, each the leader in its group for having established the best safety record during the year, were awarded the national safety trophies 'Sentinels of Safety.Since these annual contests were begun 11 years ago the scope of the competition has been broadened materially, both as to the number of plants participating and as to the number of man-hours of exposure to accident hazards. Moreover, marked progress in the pre¬vention of accidents has been achieved, as is indicated by an almost constant downward course in the accident-frequency rates for the contest group as a whole during the past 11 years. On the other hand, the accident-severity rates for the group showed an upward trend during the first part of the period and a downward trend during the latter part, except in 1930 and 1934, when two disastrous explosions occurred with heavy loss of life, and in 1935, when there was an increase in the number of fatalities although no major disasters occurred. The accident rate for 1935, both as to frequency and severity, was higher than for 1934.The National Safety Competition is conducted by the Bureau of Mines in the interest of safety in the mining and quarrying industries. This object is accomplished directly through the efforts of the competing companies and their employees to win first place in the competition and thereupon receive well-merited and national recognition for their achievement. Indirectly the purpose of the contest is accomplished through studies by the Bureau of Mines of the fasts contained in the accident reports which the competing companies furnish to enable the Bureau to compute the accident rates that are the basis for determining the winners of the contest.The statistics that constitute the basis for determining the winning companies and the relative standing of all companies are prepared uniformly without regard to the States in which the companies operate, or to differences in classes of accidents covered by State laws relating to compensation for injuries resulting from industrial accidents."

Jul 1, 1936

By William R. Yernberg

The Society of Economic Geologists (SEG) held its biennial conference May 14 through 16, 2006, in Keystone, CO. SEG is an international organization with about 3,500 individual members with interests in economic geology. The 2006 SEG conference theme was “Wealth creation in the minerals industry — integrating science, business and education.” The conference exceeded expectations with 705 participants, including 102 students, from 44 countries. The conference featured 30 oral presentations, 24 professional posters and more than 70 student posters. The conference also included a trade show with 50 vendors, numerous field trips, workshops and social activities.

Jan 1, 2006

Reduce haulage truck accidents resulting from blind spots, with a special emphasis on reducing accidents during backing operations.

Jan 1, 1997

By R. D. Hull

Paper written on project work carried out in partial fulfilment of B.Sc. (Eng.) (Mining) degree As a partial fulfilment for the degree of B.Sc. (Eng) (mining) at the University of the Witwatersrand, a dissertation was to be completed in the mining industry. This was done at Finsch mine, with the purpose of determining the best solution to the required secondary breaking problem. In order to complete the study of the secondary blasting method available for use in the new block 4, cave mining method at Finsch mine the following problem statement was identified and solved ?The methods currently in use, for the secondary breaking of oversize rocks at their source in the current production levels, are to be investigated, and their applicability to the new block 4mining project determined?. To effectively achieve this problem statement above; time was spent researching and investigating, in depth, the methods that are currently in use at both Finsch and Koffiefontein mines; so as to gain practical knowledge of these. The methods were identified and independently evaluated, taking into consideration factors such as costs of the equipment, time to break oversize rocks, advantages, disadvantages, safety and labour requirements, etc. This in turn then allowed for a direct comparison between the methods and the decision as to the best to apply to the new block 4 production level. The methods that were investigated included: ?Concussion blasting, where concussion bombs and lay-on charges are used to break hang-ups and boulders. ?Drill and blast methods, where holes are drilled in large rocks and charged manually with explosives. ?Emulsion secondary blasting, which is a new project in use at Koffiefontein mine from African Explosives Limited. ?The Ro-BustTM breaking system, a hydro-fracturing breaking system. Once all the methods had been evaluated and compared it was found that the Ro-BustTM Breaking system was the most applicable for the breaking of boulders, with, the Emulsion Blasting System being used for hang-ups. Further information and the more in-depth version of this report, is stored in the resource centre at De Beers?Finsch Mineand the School of Mining Engineering WITS University.`

Jan 1, 2002

By Hanns J. Billmayer

Optimized Operator Compartment layouts based on previous Bureau of Mines activities in standardization and optimization of controls were designed and installed in three operating vehicles. Two National Mine Service 48A-36 TorKars were modified in production prior to delivery to the Quarto Mining Company. An Elkhorn AR-4 scoop owned by Adanac Coal Company was modified in a local rebuild shop. The modified vehicles were then evaluated underground under normal production conditions for a 60 day period. Vehicle operators and management appear well satisfied with the compartment modifications.

Jan 1, 1976