Search Documents

By George D. Brunton

The past and present argillaceous rock studies for the U.S. National Waste Terminal Storage Program consist of: (1) evaluation of the geological characteristics of several wide- spread argillaceous formations in the United States; (2) laboratory studies of the physical and chemical properties of selected argillaceous rock samples; and (3) two full-scale in situ surface heater experiments that simulate the emplacement of heat-generating radioactive waste in argillaceous rock.

Jan 1, 1981

By A A. Latscha, D O’Connor

Increasing orebody complexity, restrictions in ground access, and longer lead times for disturbance approvals, have generated the need for the Resource Development Team within Rio Tinto Iron Ore (RTIO), to explore optimised drill design techniques that deliver resource conversion value while maximising program outcomes. In response to this challenge, the Team initiated a case study to produce an AI assisted/designed drill program using a non-machine learning AI. The case study involved the assessment and implementation of an AI generated drill program at one of RTIO’s Pilbara iron ore deposits, located in the Hamersley Province of Western Australia. The Mineral Resource is currently classified as 100 per cent Inferred. Access constraints inherent to topography, and the presence of exclusions zones have prevented adequate drilling coverage, resulting in lower resource confidence and a poor definition of the orebody extents and geometry. The drill campaign, planned in Q1 2023, needs to consider access constraints, complex topology and the limitations related to additional ground clearance, while addressing the requirement of improving orebody knowledge. The drill plan had to address two objectives. The first and main aim of drilling was to upgrade the Resource Classification to allow for possible conversion to Ore Reserve. The input for this objective was a volumetric representation of the areas currently not meeting pre-defined quantitative Resource Classification upgrade criteria. The second objective was to better define the orebody extents and geometry. For the second objective, the input to the drilling optimiser was a volumetric representation (blocks) of the areas of high uncertainty in the mineralisation/waste boundary, which were defined using an indicator conditional simulation technique. The drilling optimiser output was a range of compliant drill plans. A set of KPIs based on economic and orebody knowledge criteria were used to assess the plans and to select the most optimal drill design to be drilled in 2023. The geology and management teams were able to make better informed, objective decisions using the trade-off between cost and orebody knowledge gained. As part of the assessment, the AI generated plans were compared to our current planning practises. The AI assisted plans, when gauged against the project KPIs, showed clear and measurable improvements in both meeting project objectives and in managing operational risk.

May 24, 2023

By Mauricio Guimarães Bergerman

At the regrind or secondary grinding stages of base metal ores, the concern about energy efficiency is usually extremely important. In general, the specific energy consumption at this stage is higher than during the primary grinding stages. In addition, a tendency of finer grinding has been observed in the new projects of metallic minerals, due to the finer mineral liberation, which leads to increasing capital and operational costs. At Vale?s new copper projects in Brazil, regrind sizes with a P80 of approximately 40 to 20 µm have been necessary. Conventional ball mills, adequate for primary grinding, usually bring about low energy efficiency with products bellow 50 µm. Vale is using the vertical mill on its copper projects ? Sossego and Salobo, in order to optimize the regrind of rougher concentrates and reduce energy consumption. This paper presents the results of industrial surveys carried out on the Vertical mill circuits of Sossego plant during its initial years of operation, and compares these results with the design criteria and laboratory regrind tests used for the mill scale up. Keywords: grinding, regrinding, copper, vertical mill, stirred mill

Sep 1, 2012

By Nicholas Zabaras, Deep Samanta

"Solidification of metal aluminum and aluminum alloys is modeled on uneven surfaces characterized by sinusoidal curves. Wavelengths and amplitudes of these sinusoidal surfaces are varied to study their effects on processes like solidification, macro-segregation and inverse segregation. Solidification and macro-segregation are modeled using a slightly modified form of a stabilized finite element method developed recently to model high Rayleigh number solidification and porous media flows. For pure metal solidification, the effect of varying amplitudes and wavelengths is observed in heat transfer, fluid-flow ~nd phase change processes. The relative importance of shrinkage driven flow and solutal convection on the redistribution of solute for an alloy solidifying in a rectangular cavity is compared. The analysis is then extended by modifying one of the surfaces to a sinusoid. In this case the effects of varying amplitudes and wavelengths are studied in heat transfer, fluid flow, phase change, macro-segregation and inverse segregation processes.1 IntroductionTransport phenomenon during solidification of alloys is a major cause ofcasting defects such as segregation, micro-voids, hot tears, porosity, internal and surface cracks. Heat flow across metal and mold surfaces directly affects the phase change process and plays an important role in determining freezing conditions within the metal. In alloys, natural convection and shrinkage play an important role in determining the final solute redistribution, macrosegregation and evolution of solid macromorphology. Surface unevenness plays an important role during the early stages of solidification. It influences the heat transfer rate and fluid flow in the melt, which in turn affect the morphology and shape of the solid-liquid interface. The effect of surface unevenness on solute redistribution is important during solidification of alloys, where solute driven flow in the mushy zone is prominent. Thevik and Mo in [7] and [8] used a one dimensional model for studying surface segregation and macrosegregation in alloys under the influence of exudation and solidification shrinkage. Air-gap formation in their model was expressed through a variable convective heat transfer coefficient at the boundary. Tsai et al. in [3] and [4] have modeled macrosegregation in an aluminum-copper alloy driven by shrinkage and solutal convection. They used a single domain model based on mixture theory and solved the transport equations using finite difference methods. Our aim is to model solidification of aluminum followed by macrosegregation and inverse segregation in aluminum-copper alloys on uneven surfaces by finite element methods. These surfaces are modeled as sinusoids characterized by amplitudes, ?s and wavelengths, As, By varying As and ?s, changes in heat transfer, fluid flow, phase-change and macrosegregation are studied."

Jan 1, 2004

By B. Ballard

Engineers at a West Virginia coal preparation plant owned by one of the nation's largest coal producers sought a fire suppression system for the plant's MCC and cable spreading rooms. Officials considered the traditional options of water-based sprinklers, dry chemical, and clean agent systems; however, each of those options presented challenges. Sprinklers can damage electrical equipment, proper delivery of the agent and adequate coverage/protection can be an issue with dry chemical systems, and clean agent systems require room integrity. An alternative to traditional systems was discovered in the Victaulic Vortex Fire Suppression System. The first hybrid inert gas/water mist system (FM 5580), Vortex adequately addressed these concerns. The system, which deploys a high-velocity, low-pressure mixture of water and nitrogen, is not damaging to electrical equipment and extinguishes fires in open, ventilated areas. This is one of the first installations of the Vortex system in a prep plant, and is a compelling example of how new technology can overcome the challenges of traditional technologies. The paper will detail plant specs, situation, and system evaluation, selection, and configuration.

Feb 23, 2014

By H. A. Johansen

Recent advances in the metallurgy of chromium have enabled this metal to begin to take its place among the refractory metals. Considerable work is being done on the development of high-temperature alloys containing high percentages of chromium.1/2/ In spite of the relatively large amount of work done on these alloys, little is known of the properties of the pure metal. Information in the literature concerning the tensile properties of pure chromium metal is quite scant. This deficiency maybe explained by the great difficulty of preparing test specimens from such a brittle material, resulting in many losses in each phase of the specimen preparation and testing procedure.

Jan 1, 1954

By W Newns

This paper describes laboratory and in situ tests and determines a set of parameters for stiffness and strength properties for a weak sedimentary rock mass, the East Coast Bays Formation of Auckland. The parameters derived are discussed in relation to peak strength and in respect of deformation limits associated with sequential excavate and support (SEM) or conventional tunnelling.

Mar 8, 2011

By C. Y. Tang, Z. H. Chen, T. C. Lee

"In sheet metal forming process, the forming limit and strain distribution are governed by plastic instability and fracture following strain localization. It has been proved that the temperature gradient caused by plastic deformation as well as friction is one of the crucial factors to induce the strain localization in high-speed metal forming processes. In this paper, a numerical simulation of the sheet metal extrusion process has been conducted by using thermal-mechanical coupling finite element method. An improved mixed finite element method has been used to solve the large deformation elasto-plastic problem. In thermal phase, the transient heat transfer finite element method together with the Crank-Nicholson algorithm has been employed to determine the temperature field. Both the numerical results and the experimental observations reveal that the temperature gradient plays an important role in inducing the strain localization, which eventually leads to fracture failure in the sheet metal extrusion process.IntroductionSheet metal extrusion is such a process where the extrusion punch penetrates into one surface of the sheet metal material to let it extrude and flow towards the outlet of the die. This process can be used to produce protruding parts on a strip material. In engineering applications, the quality of the product is affected by many factors such as stress state, loading speed, material properties and lubrication condition. The research on failure mechanisms and improvement of formability in sheet metal forming processes by exploitation of differential thermal conditions has been of great interest recently [1-3]. It has been proved that the temperature gradient caused by plastic deformation, heat transfer, and friction between sheet and tools is one of crucial factors to affect 'the formability in high speed sheet metal forming processes [4]. In our previous study of sheet metal extrusion, it has been observed that plastic deformation is highly localized and some specimens are subjected to fracture failure in the form of crack propagation [5]. To understand this failure phenomenon, the effects of temperature gradients must not be ignored."

Jan 1, 2001

By AIME AIME

THE Board of Directors of the Institute has authorized the appointment of a committee to draw up rules of procedure under which awards can be made from time to time to petroleum engineers for outstanding contributions to the art of finding and producing oil and gas. These awards will 11e sponsored by the Petroleum Division and are the first recognition by any professional society of outstanding achievement in "oil mining." They will be in the form of either a gold medal, scholar- ship, or other suitable prize. The awards will be financed from the income of the Anthony F. Lucas Memorial Fund, which was started about fifteen years ago, shortly after' his death, by admirers of Captain Lucas.

Jan 1, 1936

By Albert G. Zima

THE conservation of strategic materials during war rime gives rise to many problems not commonly encountered in times of peace. During normal times, when world trade is unrestricted, we are apt to become lavish to a point of extravagance in our use of those materials which, during rime of war, become scarce owing to inadequate transportation and production facilities or because the enemy may be in position to control sources of supply. It becomes necessary, then, to enforce rationing of available sup-plies, and in some cases, where such supplies are wholly inadequate, we find we must resort to the use of substitute materials. We are now confronted with such a problem to an extent never before experienced, with the result that many of the commodities upon which our civilization depended are now either shut off completely or, because of the heavy demand occasioned by war production, are not available in sufficient quantities to meet requirements predicated on peace-time standards and manufacturing methods. It has become necessary, therefore, to make many changes, some of them very drastic indeed, to enable us to carry on our war effort effectively. This? discussion will deal briefly with one phase of this problem, namely, the conservation of alloys required in the making of steels necessary for war production. In line with a request from the War Production Board, the Technical Committee on Alloy Steels of the American Iron and Steel Institute made a study of experimental steels embodying the !east amount of alloying constituents, with the objective in mind of substituting these steels wherever possible for the standard alloy steels used heretofore. This study embraced the following phases: (1) The availability of silicon and manganese; (2) The average quantity of alloying elements recoverable from scrap; (3) The effect of increases in manganese and silicon contents on the general properties of steel; ( 4) The elements and ranges of elements which might be used to duplicate the hardenability of the steels now in use; (5) The effect of combining several elements in small quantities upon the properties of steel at various hardness and strength levels; (6) A determination as to whether or not the steels selected would suffice for general application. Working on this basis, the Committee arranged for the manufacture of several heats of steels containing various combinations of different amounts of such elements as silicon, manganese, chromium, nickel, and molybdenum. The steels thus produced were compared by hardenability tests.

Jan 1, 1943

By Ralph H. Sweetser

MUCH progress in -blast-furnace construction and in the manufacture of firebrick for furnace linings has been made since the publication of Bulletin 130 of the U. S. Bureau of Mines on "Blast-Furnace Breakouts, Explosions and Slips, and Methods of Prevention," by F. H. Willcox in 1917. At the time of publishing this report comparatively little information was available to blast-furnace men as to the fundamental facts relating to the character of blast-furnace refractories. Some of the accepted theories of only a few years ago have been completely reversed. The mortality of blast-furnace linings used to be so great that nearly every furnace plant had one or more complete linings in the brick shed ready for use in case of a lining suddenly "going out"; it was generally accepted that a furnace could not "keep her lines" more than two or three years at best, and often a hot spot in the shell would develop, or a breakout occur in the hearth or bosh within a year or two after blowing in on a new lining. In some respects these frequent relinings were not so detrimental as to he a complete loss because they afforded opportunities to take advantage of advances in blast-furnace practice. At present the cost of relining has greatly increased, but the life of a lining has also increased. Anything less than five years on a lining is now considered a short blast.

Jan 1, 1932

By K. Mukherjee

Instantaneous resistance change during martensitic transformation in Fe-30 at. pct Ni alloy has been studied using a low-noise electronic system. The smallest signals recorded in this investigation were of the order of 10 pv. These small signals did not show the initial increase reported by earlier investigators to support a double shear mechanism.&apos; A variety of pulse shapes and sizes was observed during "burst" transformations, and these signals were neither a linear function of the size of martensite plates nor of the volume fraction transformed. Even the smallest signals, presumably from single plates, showed complications resulting from elastic and/or plastic deformation, shock wave propagation, and so forth, which are inherent in the growth process of a martensite plate. The time of formation and interface velocity determined froni this experiment agree very well with the pioneering work of Bunshalz and Mehl.&apos; AN Fe-30 at. pct Ni (c0.005 pct C) alloy was used to study the time of formation of martensite plates. Martensitic transformations, unlike the nucleation and growth processes, are usually characterized by an extremely fast reaction rate. During the transformation, the crystal structure changes and this change is propagated through a finite volume of the parent crystal lattice within a very short time interval. The interface between the two phases probably consists of moving dislocations, and the time of formation of the plate depends on how fast this dislocation interface can move. Knapp and Dehlin~er or Cottrell and Bilby mechanisms, or similar dislocation models, can be used to calculate the time of formation of a martensite plate of a given size. In the past, conventional photographic technique475 as well as electrical resistivity techniques"~-" have been used to measure the time of formation of a martensite plate. The specific resistance of the martensitic phase in Fe-30 at. pct Ni alloy is lower than that of the austenite phase. Therefore if a current is passed through a small austenite sample in series with a large external resistance, then one would observe a voltage change across the sample as martensite is formed. Such dc measurements are shown in Fig. 1. The initial large voltage drop in Fig. 1, at the M, temperature, is due to a "burst" transformation where a large number of plates are formed in a cataclysmic manner within a very short interval of time. Even during the later stages of transformation as shown in Fig. 1, one can observe discontinuous voltage changes due to small bursts. In order to resolve the time scale of such discontinuous stages, the voltage signals are amplified and fed into a highspeed oscilloscope. In this investigation a low-noise amplifier was used for the first stage of amplification. The signal to noise ratio was further improved by the design of a pulse transformer. This transformer was capable of amplifying the signal by a factor of six. Voltage signals were studied over a wide time scale ranging from 2 sec to 0.1 psec. I) EXPERIMENTAL PROCEDURE A) Specimen Preparation. Specimens were cut from induction-melted Fe-30 at. pct Ni (<0.005C) alloy and cold-rolled to 0.2 by 1 mm cross section and an average length of 5 cm. During mechanical shaping, the specimens were strain-annealed at 950°C for 24 hr in vacuum. Finally the finished samples were vacuum-annealed at 1000°C for 6 hr and water-quenched to room temperature. The average grain diameter was 0.02 cm. B) Cooling System. The M, temperature of the alloy was -55°C. Fig. 2 shows the arrangement which was used to cool the specimen at a slow rate. The specimens were mounted inside a i -in.-diam hole in the 2-in.-long section of the copper specimen holder. This cavity was filled with silica gel. A dummy specimen was used under identical conditions for

Jan 1, 1969

One of the major changes in the resource industry in the nineties has been the re- internationalisation of the industry. The history of the resource business has been one of companies from the developed world utilising the cash flows from their operations to explore and develop mines in less developed regions of the world. This resource development has progressively generated wealth and economic development, which in tum, has led to a new generation of exploration and mining projects. &nbsp; InSouth America, Chile had led the way in a mining resurgence, now closely followed by Argentina, Brazil, Venezuela and Peru. Although Chile has long had a significant copper mining industry, the pre-nationalisation phase was driven by American capital; the current phase has been spearheaded by RTZ - BHP at Escondida with Canadian junior companies, in particular, providing major speculative impetus. The Australian junior companies have not been significant in South America. &nbsp; Although Canadian and USA exploration appears to be in decline, the mining industry, particularly in gold, is buoyant in North America. Interestingly, a number of listed and unlisted Australian companies are active, particularly in United States exploration. &nbsp; Australian-based companies have dominated the South-East Asian exploration scene, especially in the Vietnam region. To date, the combination of political and legislative uncertainties have failed to lead to significant resource developments in this region. The area remains one of great potential, as exemplified by the exciting developments in Indonesia. &nbsp; The Philippines has a history of mining, and this has been dominated by both local and North American operators. Both large and small Australian resource companies have a presence in the Philippines, and the development of the copper-gold potential could be impressive over the next decade. &nbsp; The tales of the undeveloped mineral potential of China are probably rivalled only by the supposed strings of virgin Russian orebodies! Many Australian companies appear to have looked but few have chosen to proceed with Chinese developments. There seems little likelihood that China will, in the foreseeable future, rival South America as a target for Australian and North American resource capital. &nbsp; Papua New Guinea has had an active, albeit chequered history in mining, with Australia long being the predominant source of exploration and development funds. The developing nation status of PNG has generated extreme uncertainty, with the current exploration scene all but dead. Most recently, the international flotation of Lihir Gold has tested the international and Australian investment community&apos;s commitment to PNG resource development. &nbsp; The Australian exploration scene continues buoyant, although dominated by gold. The base metals scene is generating, on average, one significant base metal mine developed every couple of years. This is probably the fastest rate of significant base metal development in Australia&apos;s history. &nbsp; The gold scene has been one of incredible dynamics, and there is no evidence that this momentum is waning. The development of new exploration techniques, together with a number of the companies reaching a critical size, has added to the momentum in the industry.

Jan 1, 1995

By K. P. Chong

Fracture toughness of oil shale is an essential property in fragmentation to optimize particle sizes and permeability distributions in in-situ processes. Fracture mechanics of oil shale has been based on conventional fracture mechanics using notched samples and assuming the material to be isotropic and elastic. Oil shale is a layered material more accurately characterized as transversely isotropic. The senior author proposes to use a semi- circular core specimen with a center crack subjected to three point bending. Singular crack tip elements with isoparametric elements are used. The precracked semi-circular disk is modeled under displacement loading. The effect of crack length on the non-dimensionalized stress intensity factor is investigated by strain energy method, ellipse method, and stress method. Very close agreements are found. The fracture toughness is obtained by compressing the specimen in to failure. Parameters such as oil yield are investigated.

Jan 1, 1984

By Northcutt Ely

This chapter deals with the systems of laws by which governments regulate the exploration for and production of the minerals within their jurisdictions. It is a summary, restricted by necessary space limitations, of material assembled by the author for a publication of the United States Bureau of Mines, "Summary of Mining and Petroleum Laws of the World," (Information Circular 80 1 7, 196 1. ) The present study is organized in three parts, dealing with (1) the historical background of these legal systems, (2) laws of the United States, and (3) laws of other countries of the world. The reader&apos;s attention is invited to the acknowledgments at the end of the chapter, which inadequately express the appreciation due those who have assisted in the collection of this material. Part I. Historical Development of Major Western Systems of Land Tenancy with Respect to the Ownership and Control of Minerals The use of metals in primitive societies was largely confined to the manufacture of weapons for self-preservation. The ruler&apos;s control over copper, then bronze, then iron, was essential to maintenance of his own ascendancy at home and his group&apos;s position against neighbors who had access to similar metals. Ancient societies were thus characterized by the ruling group&apos;s ownership of minerals and metals. The Egyptian civilization, which emerged in the fourth millenium B.C. upon the agricultural subjugation of the lower valley of the Nile, was responsible for extensive development of the upper valley as a source of mineral wealth. The production of gold during the height of that civilization has been estimated at $30,000,000 per year, thus equaling the early placers of California and Australia. The mines of Egypt were the property of the Pharaohs and were controlled at their direction. Greek mining developed a different scheme of land tenancy which more closely resembled modem concepts. Development of mineral resources was

Jan 1, 1964

By W. E. Bardelmeier

The high speed conveyor type self unloading bulk carrier concept has been around for about 70 years. Although the design was developed, refined and steadily improved in the Great Lakes, to date limited numbers of such vessels have emerged in the bulk ocean trades, and these have tended to concentrate within specific mineral trades. For example, North American gypsum companies have embraced conveyor self unloaders to the point where such vessels almost exclusively carry the gypsum requirements of this part of the world. One major aluminum company has developed an impressive fleet capability in self unloaders. Application of other ships tends to be fragmented through several mineral trades. A few years ago a new phenomonen began to appear on the Great Lakes. Whereas it had historically been accepted in that region that self unloaders were effective vessels for the minor bulk trades including limestone, coal, salt, gravel and sand; they had seldom been employed heavily in the big volume iron ore trades. Suddenly, however, the new generation of 60,000 ton Lakers which emerged were all designed as high speed self unloaders. The new vessels intended to trade especially in ore, or alternatively especially in coal, have somewhat different internal features, but the important point is that all are self unloaders.

Jan 1, 1979

By Mim Li, Huimin Lu, Lisha Yang

"CuInS2 thin films solar cells have drawn much attention for their low-cost, stability and high conversion efficiency. The electrodeposition of Cu-In precursor films, as the first step in making CuinS2 solar cells electrochemically in the air-and water-stable ionic liquid based on choline chloride/urea eutectic mixture has been investigated at constant potential. Compared with aqueous electrolytes, the large electrochemical window as well as the high thermal stability of this ionic liquid allow the direct electrodeposition of Cu-In precursor films. Then the precursor films were sulfuretted in a tube furnace at different sulfurization temperatures to optimize the films properties. The films obtained were characterized by X-ray diffraction (XRD), scanning electron microscope (SEM), energy dispersive spectroscopy (EDS).IntroductionCuInS2 is one of the most prospective absorber materials for low cost thin film solar cells, with a high conversion efficiency that exceeds 32% in terms of theory and nearly 13% in laboratory level [1-2]. In addition to its long-term stability, CuinS2 has a band gap energy Eg ranging from 1.3 to 1.55 eV and an optimal optical absorption coefficient reaching 105cm-1 [3-4]. CuinS2 thin films have been prepared by several methods such as spray pyrolysis [5-6], r.f.sputtering [7], vacuum evaporation [8-9] and electrodeposition. Comparing with vacuum methods, electrodeposition has lots of advantages such as less energy consumption, preparation big area thin film, stable system and enabling cheaper films.The electrodeposition of most technologically important metals has been shown to be possible from a wide range of ionic liquids. These ionic liquids are currently applied in a wide variety area. It is reported that the cell efficiency of chalcopyrite absorber layer (CIS, CISeS, and CIGS) via an electrodeposition route in laboratory condition has reached 11.3% [10]. Copper and indium alloy film is regarded as important precursor for the production of compound semiconductors with sulfur. The electrodeposition of the alloy film from room temperature ionic liquid (RTIL) has not been widely investigated. Only few alloy films, such as ZnTe, CdTe, GaAs and AlSb have been electrodeposited."

Jan 1, 2011

By Iwu GO, Almond DP, Joasoo _

The gravimetric integral Knudsen effusion method was used to measure cadmium activity values in binary liquid In-Cd alloys in the range 523 to 573 K. The activity measurements together with other studies from the literature indicate that special bonding conditions exist in the melts near a composition corresponding to InCd3. Sound velocities in In-Cd melts were also measured using a precision pulse-echo over- lap method in the range 404 to 953 K. The frac- tional deviation of experimental and ideal isentropic compressibilities at 623K shows a functional dependence on composition with a pronounced maximum near the composition 75 at.%.

Jan 1, 1980

By Raymond K. Will

Computers are becoming increasingly valuable tools in the mining industry as a greater variety of appropriate hardware and software becomes available, combined with greater acceptance by management, Within a given time period an engineering staff can evaluate or design a project to much greater detail and higher accuracy by utilizing computers once suitable programs have been developed. We are all aware that throughout the world the decreasing grade of minerals coupled with increasing waste to ore ratios necessitate larger capacity, longer term mining operations and attendant higher capital costs. Computers can be of assistance in all stages of mineral exploitation, from geologic exploration through mine feasibility studies and design, to marketing and transportation. Because of the high speed with which data can be digested and manipulated by computers, preliminary information from any stage of investigation can be analyzed to assist in further guidance of that stage. By use of preliminary mine feasibility studies, financial forecasts and sensitivity analysis, even information from a far-removed phase such as marine transportation of the product, can help guide the exploration phase to a realistic target.

Jan 1, 1973

By NIOSH NIOSH

This work explores application of a double alkaline leach method to extraction of alumina from Oregon ferruginous bauxitic materials. The process recovers a greater proportion of alumina from high-silica ores than is possible by a conventional single-leach method. This recovery is accomplished by calcining the ore, removing reactive silica in a preliminary dilute caustic soda leach, and then applying a second leach to dissolve alumina. Ores containing up to 15 percent Si~) 35 percent AI;:) Os, and 30 percent Os were examined. Under conditions of treatment established by experimentation, more than BO-percent alumina extraction was demonstrated. When and if conditions demand the use of low-grade materials, the double-leach process is capable of providing millions of tons of alumina from Oregon ferruginous bauxite.

Jan 1, 1963