Search Documents

By Robert J. Ramsey, N. Finkelstein, Robert D. Jeppson

Introduction The Utah Copper Division of Kennecott Copper Corporation will present its contribution to the A. M. Gaudin Flotation Symposium in four parts. The first two segments will discuss briefly the historical development of the Utah Copper Division and describe the ore body. The third segment will review the facilities and operating procedures for the Utah Copper Division's newest plant, the Bonneville Concentrator. The fourth segment describes flotation process circuitry, including molybdenite recovery procedures, at the Arthur and Magna concentrators. (The Bonneville concentrator is a crushing and grinding unit and does not have its own flotation plant). 1. Historical Development Progress through change has been the key to the successful operation of the Utah Copper Division for more than 70 years. As the original low-grade copper operation, the pressures to remain competitive and profitable have dictated the timing and extent of each change. Much of the change has occurred through technological and economic advancements in the area of ore concentration. The Utah Copper Division of Kennecott Copper Corporation had its origin June 4, 1903, when the Utah Copper Company was organized. The initial mill of 300 tpd (tons per day) capacity was built at Copperton a few miles below the present Bingham Canyon mine site. From 1904 to 1910, the Copperton mill was expanded to a capacity of 1,000 tpd, and all of the known apparatus for gravity concentration were evaluated.

Jan 1, 1976

By J. P. Martin, A. H. Geisler, J. H. Crede, E. Both

The investigation of a 50 pct Co alloy was undertaken to determine whether there was any direct correlation between the structure and properties of Co-Fe alloys which were given various magnetic heat treatments. The magnetic anisotropy and texture of the 0.002-in. cold-reduced 98 pct material tend to decrease and change in nature with increasing temperature of the recrystallization anneal. Annealing samples in a magnetic field had little effect on either the magnetic properties or texture. However, cooling them in a magnetic field greatly improved their magnetic properties. THE beneficial influence of a magnetic field applied during the heat treatment of certain soft magnetic materials has been known for a long time. Early work showed that the presence of a magnetic field of a few oersteds during the heat treatment of Fe-Ni alloys will cause a large increase in maximum permeability. A pronounced increase in the residual induction which is produced by the magnetic anneal causes the hysteresis loop to approach the shape of a rectangle. Such results are beneficial since the desired properties are high permeability, high induction at maximum permeability, high residual induction, and low coercive force. More recently Libsch and coworkers1 studied the effect of magnetic annealing on the hysteresis properties of a series of Co-Fe alloys prepared from powders. They observed good response for the 35 and 50 pct Co alloys but little response for the 42 pct Co alloy. They pointed out that this was somewhat surprising since the 42 pct alloy has a high linear magnetostriction and zero crystal anisotropy and similar conditions in Fe-Ni alloys give excellent response to magnetic annealing. They found optimum properties to be at the 50 pct composition with residual induction, Br = 19,000 gauss and coercive force, Hc = 0.68 oersteds after the magnetic anneal. Before the magnetic anneal these values were B, = 12,600 gauss and Hc = 1.15 oersteds. The optimum treatment consisted of cooling from above the y-a transformation temperature to 900°C in a field of 20 oersteds, holding 11/2 hr at 900°C, then cooling at a rate of 20° to 25°C per min in the field to below 230°C. Cooling rate mainly affected coercive force with the value decreasing from 1.09 to 0.88 oersteds as the rate was increased from 3° to 48°C per min. Cooling from 1020" to 900°C in a field followed by further cooling to 230°C without the field gave properties decidedly inferior to those for samples annealed with the field applied throughout the cooling. They concluded that to get the best properties the samples must be cooled in a field to a threshold temperature above which the alloy is plastic enough to be affected by magnetostriction. In this respect the holding temperature must be high enough so that the alloy exhibits good plasticity to permit the optimum orienting of magnetic domains by relaxation of magnetostriction. In contrast, the holding time was of less significance for there was little improvement when the time exceeded 1/2 hr. The improvement in properties effected by magnetic annealing has usually been attributed to the establishment of a domain texture caused by the "freezing in" of magnetic strains. On the other hand, Smoluchowski and Turner2,3 apparently found that a magnetic field applied during recrystallization could alter the crystal texture. If this effect is real, improved properties would also be expected when

Jan 1, 1954

By Harry L. Brown, Philip E. Armstrong

Young's modulus doto ore presented for W, Mo. Ta. V, Cr. Ni, Ti, and Zr as a function of temperature up to about 0.7 of the melting points. A plot of reduced temperature us reduced modulus produces a general correlation except for titanium and zirconium. Young's modudlus data for some representatiue commercial graphites are given up to 2400°C. All results were obtained from longitudinal resonance-frequency measzrrements of 4-in. long samples, corrected for simultaneously measured thermal expansion. Comparison of poly crystalline and single-crystal tungsten behavior indicates that all the observed modulus values are frequencv -dependent at the higher temperatures. STATIC measurements of elastic properties of materials at elevated temperatures are extremely difficult to make since the elastic behavior is obscured by relatively large first-stage creep effects. Dynamic methods which avoid this difficulty by utilizing the measurement of the resonance frequency of a simple vibrational mode have been described in the 1iterature.l-3 The authors have extended the operating temperature range of this type of measurement to above 2000°C and have described the equipment elsewhere.~ The Young's modulus data presented here were obtained with this equipment, using samples about 4 in. long and 1/4 in. diam, supported horizontally at the center and excited to the fundamental longitudinal resonance frequency. Young's modulus was calculated by the formula: E = 4f2f2p where E = Young's modulus, / = frequency, 1 = length, and p = density. Dilatometric data were obtained simultaneously by optical measurements of the change of length of the sample. For the metals tested, an attempt was made to obtain modulus values that would be representative of the pure, strain-free, randomly oriented material. All of the graphites studied exhibited a high degree of elastic anisotropy, while the method assumes an isotropic homogeneous material. However , when the values for Young's modulus obtained for AUC graphite were compared with those taken from static measurements at room temperature they were found to be only about 4 pet higher. This is excellent agreement considering the low precision of modulus calculations from stress-strain curves. The difficulty in using data of apparent Young's modulus for anisotropic materials arises when the attempt is made to use these data and shear-modulus data to obtain Poisson's ratio. The results are usually meaningless and sometimes absurd.' RESULTS Table I lists the sources, impurity content, thermal history, and dilatometric constants of the metal samples that were investigated. All the metal samples were tested under a vacuum of 1 to 5 x 10-5 Torr. Where our dilatometric data agreed with previously published data, the table lists the previous values and the literature reference. Where no reference is given, the constants were determined from our dilatometric data. Table II presents the modulus data in units of millions of psi as a function of temperature in degrees centigrade. The numbers were obtained from curves fitted to the experimental data. For some types of calculations, such as those attempting to correlate creep data, the slope of the modulus curve is of interest, and this information also is reported in Table 11. It is always tempting to try to fit physical-property data into some general pattern and then use this pattern to predict the behavior of other similar materials. The general pattern for an elastic modulus of a metal seems to be a linear deoro- with increasing temperature Over the range between 0.1 and 0.4 of the melting temperature, then a progressive1y decreasing value up to the melting point. Metals appear to retain finite moduli

Jan 1, 1964

By R. J. Walter, W. T. Chandler

The Ch-H phase diagram was determined for by-drogen concentrations up to ChHo.9 at temperatures below 400°P'. The phase diagram includes a mis-cibility gap and a eutectoid transformation. A peri-tectoid transformation is postulated at the hydrogen-rich end of the diagram, Phase diagrams were determined for two levels oj purity, of the columbium. A single solid solution exists in the Cb-H system above 400°F. There has been considcrable disagreement among investigators concerning the system at temperatures below 400°F. Albrecht, Goode, and ~allett' proposed a miscibility gap containing two bcc phases with the two lattice parameters converging at about 140°C (285-F), and Brauer and ~erman' found a two-phase room-temperature region between 10 and 41 at. pct H. At sufficiently high hydrogen concentrations in the one-phase region, the hydrogen-rich phase was found to be face-centered orthorhombic. Wainwright, Cook, and Hopkills3 recently reported that the face centered orthorhombic hydride phase is derived from a unit cell which is slightly tetragonal with a small departure from 90 deg of the angle (y) opposite the r axis. The orthorhombic hydride phase was observed for hydrogen concentrations between 0.2 and 0.8 H/Cb atom ratio. Paxton and coworkers4 found that needlelike hydride plates formed in a hydrogen-charged columbium single crystal and suggested that this transformation possessed the characteristics of a diffusionless phase transformation. On the basis of room-temperature, X-ray diffraction data, komjathy' suggested that an order-disorder or martensitic transformation occurs. In the present study, the Cb-H system was investigated to resolve the discrepancies found in the literature for this system. PROCEDURE The columbium specimens were prepared from two heats of wrought 1/2-in.-diameter electron-beam melted columbium rod and from two columbium powders of -80 mesh size of different impurity contents. The columbium bar stock was pur chased from Urah Chmg Corp.; the 99 and 99.5 pct purity colulnbium powders were obtained from Fansteel Metallurgical Corp. and Kern Chemical Co.. respectively. The chemical analyses of the columbium bar and powders are listed in Table I. Hydrogen charging was performed by exposing the columbium specimens to hydrogen at 1 atm pressure at various temperatures. After exposure the specimens were quenched to prevent the hydrogen pickup which would take place if cooled in hydrogen, or the hydrogen loss that would occur if cooled in an inert gas. Adequate hydrogen purity was achieved by passing high-purity tank hydrogen (maximum 5 ppm total impurities) through an Engelhard catalytic Deoxo unit, magnesium per chlorate desiccant, and finally through activated charcoal at the temperature of boiling nitrogen. Activated charcoal at -321°F has been reported6 to remove impurities from hydrogen to a nondetectable level. A schematic representation of the heat-treating apparatus is shown in Fig. 1. A metal-sheathed thermocouple embedded in the colun~bium specimen was used to control the temperature during heat treatment and to pull the specimen boat into

Jan 1, 1965

By I. Ashmole

From the point of view of the environmental impact created, dimension stone mining is a relatively benign industry. There are no emissions besides those of the diesel powered earthmoving equipment utilised in its extraction and a small amount of blasting gases. Contamination of water resources is only likely in the event of petrochemical spillages from storage facilities and equipment, and these can largely be either prevented or cleaned up effectively. The major environmental impacts are of a visual nature, while in sensitive areas, habitat destruction and the destruction of archaeological heritage may become significant impacts. The dimension stone industry has grown at an average rate of over 7% per annum since 1986, and is forecast to continue growing at this rate for the foreseeable future. The cumulative environmental impact of the industry will thus become more significant over time. This paper discusses the environmental impacts of dimension stone mining and recommends effective means for dealing with the practical aspects of reclamation and mine closure in dimension stone mining within the context of environmentally responsible business practices. The discussion focuses mainly on the operations of the Finstone Group in Southern Africa, which are considered to be world leaders in the application of environmental management within the dimension stone mining industry, although reference is also made to other situations which the authors have encountered at dimension stone quarries around the world.

Jan 1, 2008

By D. G. Sinclair

In any discussion on the subject of mine-safety, it is well to honestly face the fact at the outset that mining is a hazardous occupation and that certain inherent dangers attach to the work, which, in spite of the greatest vigilance on the part of everyone concerned, will from time to time exact their toll of in jury or death from the underground worker. Great progress has been made of late years in narrowing down the range of these necessary risks, and, illustrative of what can be done along these lines by concerted effort, it is pleasing to read from time to time of large operating mines running for weeks, months, a year or more, without a single lost-time accident. To achieve any results in the work of accident prevention it is necessary, first, to have a definite goal, such as a no-accident period, be it a week, a month, or a year, to aim at; and, second, to set up definite standards to work by. The legal code of regulations should form the basis of all standards of work at every mine and should, for this reason, cover as far as possible all conceivable phases of operation. This represents the ideal, but in practice it is unattainable, largely because of the many variables that must be considered, due to the divergence in the scale of operations and to differing geological conditions at the different mines. Hence it becomes necessary for the operator who wishes to attain the maximum in the establishment of high standards of safe operation to so amplify the code as to meet the peculiar requirements of his operation.

Jan 1, 1930

By A. C. Mulholland

The electrical control of three-electrode submerged-arc furnaces suffers from a number of complexities, mostly due to the nature of the furnace electrical circuit providing power to the furnace where the three electrodes are interconnected within the furnace through the molten metal bath. This gives rise to what is known as the interaction effect 2, where variations in one electrode?s current can cause comparable changes to the currents in the other electrodes, particularly in larger furnaces with low power factor. Resistance-based control of the electrode penetration has largely alleviated these problems, since the resistance encountered by each electrode is predominantly dictated by the length and conductivity of the current path from the electrode?s tip to the molten metal bath, which acts as the three-phase circuit?s floating neutral point. Hence resistance changes due to tip position or conductivity changes beneath one electrode do not affect the resistances beneath the others, effectively decoupling the control of the individual electrodes1. Although resistance-based control is therefore generally accepted as superior to current-based control for the regulation of submerged-arc furnace electrode penetration, a few furnace operators still prefer to use current control under specific furnace conditions. This paper presents the results of analysing the performance of both current and resistance-based control in typical scenarios encountered on industrial furnaces, taking into account a number of factors including electrode penetration, power distribution, efficiency and asymmetry of the electrode currents. In order to accomplish this, three typically encountered scenarios were simulated. The results obtained show that resistance control provides more benefit in all cases, however, the uneven electrode current distribution generated by resistance control when electrodes are on top stops may cause some concern if baking of the electrodes is required in this scenario.

Jan 1, 2009

By Sarah Ramp, Daniel V. Cacciola, Justin Labrozzi, Shafiq I. Siddiqui, Faisal Ahmed

"Construction of embankments up to 34 ft in height for twelve ramps and roadways needed for the New Jersey Turnpike Interchange 14A project required ground improvement. The subsurface conditions, consisting of up to 30-ft thick layer of highly-compressible peat and organic soils, would induce up to 8 ft of primary and 4 in. of secondary consolidation settlements to the embankments over a long period of time. Innovative ground improvement solutions were needed to meet unique challenges posed by the poor subsurface conditions, space and existing utility constraints, aggressive construction schedule, and massive size of the project. A variety of ground improvement techniques were utilized in six different zones of the embankments to limit settlements and ensure stability of the embankments. These techniques included preloading with surcharge and prefabricated vertical drains (PVD), load balancing using light weight fill, and concrete column rigid inclusions (RI). Additionally, augercast piles with load transfer platform were used under an existing bridge with low vertical clearance. An innovative approach consisting of preloading with surcharge and PVDs followed by installation of RI was needed in one of the six embankment zones with the worst, i.e., very soft, soil conditions. The design of the RI was performed by a specialty ground improvement contractor (SGIC) using Plaxis 2D and 3D softwares. The performance of the ground improvement systems was verified and monitored by load tests and instrumentations. This paper presents details of the ground improvement design, construction, monitoring results, and lessons learned, with a focus on the RI.INTRODUCTIONNew Jersey Turnpike Interchange 14A is located within the cities of Bayonne and Jersey City, in Hudson County, New Jersey. The New Jersey Turnpike Authority (NJTA) identified Interchange 14A as an area of mass congestion in need of redevelopment to improve the increasing demand of traffic and roadway safety. The New Jersey Turnpike Interchange 14A project included the construction of twelve (12) new roadways, in addition to the construction of four new bridges. The limits of construction are shown in Fig. 1.The fill height required to construct the roadway embankments varied from 2 to 34 ft. The proposed embankment side slopes varied from 6H: 1V to 2H: 1V. Additionally, mechanically-stabilized-earth (MSE) walls were utilized to retain the embankment fill along some segments of the roadways. As shown in Table 1, the proposed roadways were divided into six zones, based on location, subsurface condition, and embankment height."

Jan 1, 2017

By Robert Rhea Goodrich

This research was done partly in the non-ferrous laboratory of the Department of Metallurgy of Columbia University, under the direction of Dr. Edward I?. Kern, and completed elsewhere. Acknowledgment is due to Prof. Arthur L. Walker, Dr. Edward F. Kern and Dr. William Campbell of the Department of Metallurgy, for their kind advice and for the inspiration derived from their instruction. This report is given under the following heads: Petrographic Description (Microscopic Study); Sampling and Preparing Ore for Treatment; Chemical Analysis; Treatment of Ore. Petrogeaphic DescRiption Texture: variable. Fine to medium mixed aggregate. Original Structure: Obscurc. Secondary structure: Fractured; healed. Mineralogy (Minerds are grouped for interpretation purposes and are arranged, in each group in approximate order of abundance)

Jan 1, 1916

By Jerry E. Olson

In 1984, the U.S. Bureau of Mines conducted a mineral survey of the Black Rock Desert Wilderness Study Area (WSA) (NV-020-620), which covers approximately 319,000 acres in Humboldt County, Nevada. About 90% of the WSA is underlain by Pleistocene desert playa sediments; the remainder is comprised of Jurassic-Triassic metamorphic rocks, a Cretaceous intrusive and Tertiary volcanic rocks. Most of the WSA is within a down-dropped fault block of the Basin and Range physiographic province. No mines or evidence of major exploration were identified within the WSA; but five claim blocks within or adjacent to the WSA and zones of anomalous character as defined by the Bureau of Land Management were examined. No mineral resources were identified, but anomalous gold, silver, and indicator element content of samples taken near Pinto Hot Springs indicate resources may exist. Lithium content of samples from near-surface sediments on the desert playa is too low for resources, out geologic conditions are favorable for higher concentrations at depth. Occurrences of zeolites are not considered to be of commercial interest. Approximately 27,000 acres are held under geothermal lease, and most of the WSA is of interest for oil and gas. No evaluation of these commodities was made by the Bureau of Mines

Jan 1, 1985

By Frank Rausche

Introduction and Background Testing -Pile Preparation -Data Processing -Data Interpretation/Case Studies Case Studies - Existing Piles Stories from around the world

Jan 1, 2001

By Barber C, Buselli G

Detailed monitoring of point sources of groundwater pollution is expensive due to the high cost of drilling monitoring boreholes. Whether groundwater pollution is due to mining, industrial or domestic waste disposal, a universal difficulty when monitoring groundwater contamination is the placement of boreholes to adequately define the extent of the pollution plume. This paper reports groundwater 'resistivity variations determined from transient electromagnetic soundings at a domestic waste disposal site north of Perth in Western Australia. Together with available hydrogeological and water quality data, the geophysics provides a broad "plume scale" picture of groundwater contamination. A simple three dimensional model of plume development, which takes account of the dimensions of the wastes, has also been developed and shows good agreement with the spread of contamination indicated by the geophysics for relatively small values of the dispersivities. Better estimates of these parameters are still required. The work indicates that a combination of geophysics and modelling with ground-truth data from groundwater quality monitoring of boreholes is required to avoid difficulties in interpretation of data and to better define the extent and migration of pollution in Groundwater.

Jan 1, 1988

By T. L. Joseph

The extent to which hot metal from the blast furnace affects open-hearth practice and the quality of steel produced has been discussed widely. Open-hearth operators have attributed difficulties experienced in making satisfactory steel to characteristics of the pig iron not disclosed by ordinary analysis. The commonest criticism of the iron has been that it is "physically cold" or "dirty." Often when the blast furnaces are working irregularly the quality of the iron is questioned. A cold hearth, slipping and hanging, the use in the past of unsintered flue dust, and the use of ores difficult to smelt have been associated with the production of iron of poor quality. The difficulty of the situation is that we have no proven yardstick for quality aside from ordinary analysis. Uniformity in analysis is recognized as being important, but the difficulty of changing the open-hearth practice when the iron analysis varies widely may not always be fully appreciated. Although the problem of correlating the characteristics of steel with those of pig iron is admittedly obscure, the effort of producers of quality steel to investigate all factors that may have a bearing on the final product is justified. This report contains data on the oxides in several hundred casts of basic iron produced in a furnace during the course of normal operation on Lake ores. Incidental to the study of the oxides in the iron, it was desirable to follow closely the temperature of the iron. The effect of temperature of the iron upon the silicon and sulphur present is discussed. A general relation between the basicity of the slag and the sulphur in the metal was developed. The amount and composition of oxides in the hot metal and in the steel bath during various intervals between melt-down and tap are discussed. Heats of rimmed steel, killed steel, and semikilled steel were investigated. The hot metal on individual heats was either all taken from a mixer or consisted partly of direct metal and partly of metal from the mixer. Samples of the iron for oxide determinations were

Jan 1, 1937

By Jan Luca Grunow, Ansgar Bendiek, Klaus Böde

According to the Markowitz portfolio theory the value of a diversified portfolio is higher than the sum of the parts of a portfolio, which is an important consideration for the correct valuation. This is valid for real estate portfolios as well as for mining assets (or enterprises). This paper analyses the application of the portfolio theory to a diversified portfolio of assets in the real estate industry and draws conclusions on further research work to be done in the minerals industry. The volume of real estate transactions is increasing over recent years. As such, the nature of those transactions is constantly changing and in some cases portfolios become more heterogeneous as they are composed of different property categories, e.g. locations and types of use. This makes their economic evaluation more difficult. This paper focuses on the acquisition of a fairly heterogeneous real estate property portfolio purchased by “Commerz Real” in Germany in Q4 2019. For economic evaluation the widely used Markowitz portfolio theory (Markowitz, 1952) was applied. It was investigated whether diversification effects could achieve added value in the form of a reduction in risk compared to the sum of their individual components. As a result the findings of this research could be applied to other heterogeneous real estate transactions and even to mine property portfolio or PPP1 project portfolio transactions.

Jun 25, 2023

By Richard Akerman

At the International Sessions of the Iron and Steel Institute of Great Britain, the American Institute of Mining Engineers and the Verein Deutscher EisenhUttenleute, held in Allegheny City, Pa., in October, 1890, Sir James Kitson, then President of the Iron and Steel Institute, presented an account by Sir Henry Bessemer of the origin of the process which bears his name.? The paper graplhically told how, after the first successes immediately following the first reports given at Cheltenham of the new process, there rapidly succceded such obstacles and difficulties in its practical application, that the whole matter was nearly abandoned in 1858. Suddenly, however, the situation changed, so that at length it became possible

Jan 1, 1894

By Herbert Clark Hoover, Lou Henry Hoover

PREVIOUSLY I have dealt with the methods of separating silver from copper. There now remains the portion which treats of solidified juices ; and whereas they might be considered as alien to things metallic, nevertheless, the reasons why they should not be separated from it I have explained in the second book. Solidified juices are either prepared from waters in which nature or art has infused them, or they are produced from the liquid juices themselves, or from stony minerals. Sagacious people, at first observing the waters of some lakes to be naturally full of juices which thickened on being dried up by the heat of the sun and thus became solidified juices, drew such waters into other places, or diverted them into low-lying places adjoining hills, so that the heat of the sun should likewise cause them to condense. Subsequently, because they observed that in this wise the solidified juices could be made only in summer, and then not in all countries, but only in hot and temperate regions in which it seldom rains in summer, they boiled them in vessels over a fire until they began to thicken. In this manner, at all times of the year, in all regions, even the coldest, solidified juices could be obtained from solutions of such juices, whether made by nature or by art. Afterward, when they saw juices drip from some roasted stones, they cooked these in pots in order to obtain solidified juices in this wise also. It is worth the trouble to learn the pro- portions and the methods by which these are made. I will therefore began with salt, which is made from water either salty by nature, or by the labour of man, or else from a solution of salt, or from lye, likewise salty. Water which is salty by nature, is condensed and converted into salt in salt-pits by the heat of the sun, or else by the heat of a fire in pans or pts or trenches. That which is made salty by art, is also condensed by fire and changed into salt. There should be as many salt-pits dug as the circumstance of the place permits, but there should not be more made than can be used, although we ought to make as much salt as we can sell. The depth of salt-pits should be moderate, and the bottom should be level, so that all the water is evaporated from the salt by the heat of the sun. The salt-pits should first be encrusted with salt, so that they may not suck up the water. The method of pouring or leading sea-water into salt-pits is very old, and is still in use in many places. The method is not less old, but less common, to pour well-water into salt-pits, as was done in Babylon, for which Pliny is the authority, and in Cappadocia, where they used not only well-water, but also spring-water. In all hot countries salt-water and lake-water are conducted, poured or carried into salt-pits, and, being dried by the heat of the sun, are converted into

Jan 1, 1950

By François Robert, Steve Green, Tyson Birkett, Dan Richardson

Abstract -Detailed sampling using a portable diamond drill, and interlaboratory comparison of selected samples have been combined with statistical studies of truncated populations to establish the gold content of several outcrops in the Val d'Or area. The outcrops chosen are non-mineralized. The background gold concentration in the rocks of the region is 5 ppb or Jess. Gold is distributed relatively homogeneously within the outcrops studied except for slightly increased concentrations within quartz-tourmaline veinlets. Three samples, of which 20 grams of powder are analyzed for each, can adequately determine the gold concentration of a structurally simple outcrop in the Val d'Or area.

Jan 1, 1992

By Mohamad Sabsabi, André Hamel, André Moreau, Paul Bouchard

"Laser-Induced Breakdown Spectroscopy (LIBS) is an atomic spectroscopy technique used to measure elemental concentrations. It is well-adapted to in-situ and in-line measurements during materials processing in general, and pyrometallurgy in particular. It is an optical non-contact technique and it can measure nearly all elements, including light elements. Our group has developed a mobile prototype system to measure molten metals. The system includes a tube, also called a lance, one end of which is immersed in the molten metal. An inert gas flows in the tube and bubbles out below the surface. The LIBS measurement is made through the tube and onto the bubble’s surface. This is done to avoid measuring contaminants, slag, or fluxes often found at the surface of the melt. An added benefit is that the molten surface is constantly renewed and thus, more representative of the bulk. An alternative to using our lance is to use a tuyère, such as a gas injection tuyère in a converter, as we did several years ago in a nickel matte converter. In this presentation, we will show various applications emphasizing more recent developments. This includes the simultaneous measurement of the concentrations of Cu, Ni, Fe, Co and S in molten matte at 1125 °C. The more obvious industrial applications of the technology include determining the best time to end oxygen blowing in the converter and elemental concentration measurement during alloying.INTRODUCTIONThe mining industry continually faces challenges in optimizing cost and productivity. Because of the large volumes of materials that are being processed, small improvement can have a big impact on benefits. Better real-time information can help improve this optimization."

Jan 1, 2016

By D. S. Rogers

"Throughout the history of mining at the Dome, gold has been found in a number of different rock types and in association with a number of different structural settings. Diamond drilling plays an important role in the evaluation of the stratigraphic and structural features which control ore deposition. The main function of diamond drilling is to locate favourable areas of mineralization.To date, over 20,000 diamond drill holes have been drilled from combined surface and underground programs. Needless to say, a great many significant intersections, carrying a wide range of gold values, have resulted from the total of over 756 miles of drill cores which these programs have produced.However, the term ""significant"" takes on new meaning in light of the experience of diamond drilling in a number of ore-type situations at the Dome Mine. Drilling through individual ore veins, such as the Fuchsite Vein or the Quartz-Tourmaline Vein, often intersect the vein structure; however, assays from the veins frequently fail to yield any ore grades. Similarly, drill cores through stringer-type occurrences such as dacite or conglomerate, when assayed, fail to indicate the true size or grade of the orebody ultimately mined.IntroductionOver the years, those who explore for gold and those who have the slightly less fickle task of actually mining gold have shared a common dilemma. That dilemma lies in the failure to relate the results of diamond drill information to a positive ore situation, or ultimately to reconcile ""diamond drill indicated ore"" to actual ore reserve tonnages.Drawing on the knowledge of more than 72 years of mining history at the Dome operation in the famous Porcupine Camp, this paper will review a number of drift and stope situations in which the grades of the ore material extracted will be compared with the anticipated grade of that same drift or zone as calculated solely on the basis of diamond drill assays."

Jan 1, 1982

By Albert W. Deurbrouck

This report describes the preparation characteristics of 23 coal samples collected from nine of the more significant coalbeds of Fayette County, W. Va. In 1963 almost 5.4 million tons of medium to high volatile B coals of excellent quality for metallurgical and steam markets were produced in Fayette County. Of the 23 coal samples collected 11 would require some upgrading to pro-vide metallurgical quality products, 11 were acceptable as received, and 1 was a noncaking coal. Cleaning these coals to metallurgical standards would require only the removal of the sink 1.58 specific gravity material which would be quite easy as very little near-separating-gravity material was present at this gravity.

Jan 1, 1965