Search Documents

By Ettore Contestabile, Cameron Thomas

Implosive connectors such as XECONEXTn have been used extensively for joining electrical conductors. This implosive action of explosives has also been used in other forms of high-energy metal working with excellent results. However, the inherent blast energy of these units can cause environmental side effects (especially airblast) which may restrict their use around inhabited areas.

Jan 1, 1994

By J. P. Ducarme

Numerous fatal/nonfatal accidents involving underground workers struck by powered machinery occur yearly, with continuous miners and roof bolters involved in the majority of these accidents. In an attempt to reduce these accidents, researchers at the the National Institute for Occupational Safety and Health (NIOSH) Pittsburgh Research Laboratory conducted studies of operator interactions with the motions of continuous mining machines and roof bolter boom arms. These operators generally perform their tasks in close proximity to the equipment in confined workspaces, often employing awkward postures. Since experiments with human subjects using the actual equipment were not feasible due to safety concerns, researchers opted to conduct controlled experiments in laboratory settings. Utilizing motion capture technologies and computer simulations, the studies collected data on equipment and operator movement in a range of seam heights and working postures. This article details the results of these studies to examine operating speeds based on usage and seam height.

Jan 3, 2010

By Fred H. Perfect

The thermite process, now approximately 80 years old, has heretofore been practiced in ceramic vessels. This paper outlines the successful production of several million pounds of alloy produced in zuater-cooled copper vessels. THE high temperatures necessary to produce fluid high-alumina slags have probably discouraged earlier workers from attempting to utilize water-cooled vessels. The following is a report of the successful application of this method, together with a report of the physical and chemical problems which had to be solved to make the process practical. About 1955, when Reading Alloys was more concerned with the production of ferrotungsten than with most other types of alloys, it was found to be exceedingly difficult to predict the reaction rate that one would experience from one tungsten ore to another . This difficulty was increased for two reasons: the physical state of the ore as received was seldom uniform, and the size of the mass to be reduced is a very important factor in developing the proper mix for the final reaction rate and temperature. For example, the reduction of ferric oxide with aluminum would theoretically produce temperatures of about 2600°C, and, in spite of the losses due to radiation, the energy is quite sufficient to produce a very fluid slag and iron effecting a very clean separation. On the other hand, the reduction of ferrous oxide with aluminum, while it is not as energetic as the first reaction, nevertheless should give temperatures above 2000"C, which should cause separation of alumina and iron, but, in practice, this is not the case and good fluid slag is not obtained. The heat of reaction, calculated from the thermo-dynamic heats of formation of the constituents of the reaction, offers a convenient guide to the feasibility of a thermite reaction. Thus, the values listed in Table I can be used as an approximate guide for estimating the results which may be expected in the reduction of various oxides and combinations of oxides using aluminum as the reducing agent. As a generalization, those reactions releasing approximately 600 cal per g of total mass represent the lower limit at which to expect separation of slag and metal. On the other hand, those reactions which release 1100 to 1200 cal per g are too violent to be used successfully without the addition of considerable inert material, such as lime, fluorspar, and so forth. Reaction rate is also a very important factor. This, of course, is governed very largely by the sizing and intermingling of the oxidant and reductant and by the starting temperature of the reactants. This is why those figures shown in Table I can only be a general guide. Further, it must be understood, that by adding powerful oxidizing agents, such as nitrates, chlorates or metallic oxides, such as molybdenum trioxide or chromium trioxide, certain problems respecting low temperatures are not necessarily solved. This is true in the addition of oxidants, such as sodium chlorate. By adding too high a concentration of sodium chlorate as a booster for a particular reduction, explosions are generated. Generally, they are of an intermittent type so as to give a Roman Candle effect to the reduction itself; with each surge resulting from a minor explosion more and more material is thrown

Jan 1, 1968

By Dennis R. Dolinar, John L. Ellenberger, Gabriel S. Esterhuizen, Anthony T. Iannacchione

A survey of pillar conditions was carried out at 21 operating limestone mines that use the room-and-pillar method. The surveyed pillars were all located in rock that was classified as “Good” to “Very Good” using the RMR rock mass classification system. The average pillar width was 14.5m and the width to height ratio varied between 0.53 and 3.52. Pillar conditions were rated using a visual rating system that accounts for the effect of geological structures as well as stress related fracturing. Nine cases of pillar instability were recorded. Pillar instabilities were typically limited to individual pillars or small groups of pillars within an otherwise stable layout. Local geological structures such as inclined discontinuities or weak bedding planes contributed to instability in seven of nine cases that were observed. Elevated pillar stresses contributed to instability in the two remaining cases. All the unstable pillars observed had width-to-height ratios of less than 1.5. It is concluded that pillar instability is most likely to be caused by unfavorable geological structures in pillars with width to height ratios of less than 1.5. Stress related instability such as rib spalling becomes more prevalent when the average pillar stress approaches approximately 20 MPa.

By James R. Wait

An attempt is made here to collect together various reports and publications that are based on research supported all or in part by Contract No. H0155008 for the past two years. The subject matter deals primarily with the excitation, transmission, and reception of electromagnetic waves in mine environments. This contract from the U.S. Bureau of Mines with the Office of Telecommunications supports the efforts of James R. Wait (Principal Investigator and Consultant to OT), David A. Hill (Co-Investigator), and various associates within the Boulder scientific community. The contributions of Samir F. Mahmoud were supported, in part, by the contract while he was a Visiting Fellow with the Cooperative Institute for Research in Environmental Sciences at the University of Colorado. Administrative assistance in CIRES has been provided by Mrs. Lana R. Hope.

Jan 1, 1976

By Ralph B. J, Sadler W. R

Thiobacillus ferrooxidans was shown to catalyse biodegradation of chalcopyrite concentrates. The process was growth associated at normal temperatures (30°C) in dilute acid solution (pH2, H2SO4) in submerged cultures. Approximately 20% of the copper dissolved in 22 days in the presence of T ferrooxidans while less than 0.6% was released when bacteria were absent. In ore column leachates, the iron and sulphur oxidizing species T ferrooxidans, ranged from I04 to I06 cells/ml while exdusively sulphur oxidizing species ranged from I02 to 104 cells/ml. T ferrooxidans predominated below pH 3 while other sulphur oxidizing bacteria favoured higher pH. Organisms were distributed vertically in ore columns according to pH differences, resulting from gradual acid consumption by gangue, during trickle irrigation.There was a sequential development of bacteria in leachates from fresh ore irrigated with water only. High pH sulphur oxidizers were always present, low pH sulphur oxidizers appeared within a week while T ferrooxidans took 50 days to show up. Routine monitoring of bacteria in dump leachates provided a qualitative indication of events in otherwise inaccessible ore bodies.

Jan 1, 1981

The mining industry is generally regarded as a high risk industry, mainly because of the difficulties in estimating the tonnage and grade of mineral resources, the fluctuations in metal prices, mining problems and other problems which occur with mining in offshore and remote locations, such as appropriation or disruption to supply. As a consequence, finance providers require a high reward from mining projects. In the past two decades, the development of "mega" projects has led to the packaging of the finance becoming more sophisticated. Some would see this move as a measure of the evolution of banking rather than an intrinsic facet of mining finance itself. Project financial managers now require a thorough knowledge of all the financial tools which are available and have to be aware of the funding options so that they can put together a finance package which minimises the cost of the financing with the risk spread adequately between the partners of the financing. The different sources and types of finance for mining projects are described herein along with the factors which determine their costs. To understand the ramifications of financing mining projects, it is essential to appreciate the fundamental difference between debt and equity, which illustrates the importance of gearing. Costs of finance are determined by the interaction of supply and demand forces. Bankers and other financiers have become more adept at isolating a wide selection of risk elements and have devised a formidable range of insurance mechanisms. There is still a lot of money looking for good project risks and if a good project is properly presented and structured, financing can be obtained in today's market.

Jan 1, 1990

It has long been recognised that Australia can benefit substantially in an economic sense from its rich resource base. The significant resources of the Gippsland Basin are a good example of the wealth of this nation. As cited in popular debate, Australia must value-add to its natural resources to ensure its long term economic prosperity. The significant oil, gas and coal resources of the Gippsland Basin have provided the Strategic Research Foundation with the basis for two major research and development initiatives ensuring the long term economic development of the Basin and Australia. The gas and coal reserves of the Basin together with the area's extensive history in electricity generation provide the rationale for establishing Ceramic Fuel Cells Ltd. A consortium comprising Australia's leading industrialist - BHP, State energy authorities and the Nation's major research and development organisations, has formed Ceramic Fuel Cells to undertake and manage research, development and commercialisation of solid oxide (ceramic) fuel cells which convert fossil fuels directly to electricity with greater efficiency and less pollution than existing technologies. The oil and gas resources of the Basin together with the valuable experience of the operators in recovering these resources, have provided the impetus to investigate the feasibility of a Marine Engineering Research Centre. The commercially oriented research, education and training objectives of the Centre are well supported by the leading industrialists in related industries.

Jan 1, 1992

By Zhou Wenbin

In this paper the mechanical properties of high carbon equivalent cast iron for automobile brake discs were analyzed through thermal analysis curves. Experiment results show that the mechanical properties have a strong correlation with thermal analysis curves and an effective way to predict the mechanical properties of high carbon equivalent cast iron was proposed based on the features of thermal analysis curves.

Jan 1, 2010

By D Matthews

With a brownfield project comes control integration challenges. The Khumani Iron Ore Mine’s second phase expansion posed a number of challenges as there was substantial brownfields work conducted. The fi rst phase was the compilation of the modifi ed process functional specifications for the project. The second phase was an audit on all of the operational sequences; this included a comparison between the SCADA sequences, sequential starts analysed from the historian data (with the potential for improvements made by the plant operators in manual start-ups) and what was proposed in the process functional specification. Differences, inclusions and missing equipment were highlighted. The third phase was the comparison of interlocking and control in the PLC with the updated process functional specification; this was done during the coding process. Running parallel to the three phases was the SCADA integration; tie-ins to the existing SCADA were conducted on maintenance days and shutdowns, in many instances with ‘dummy’ equipment to get the operational staff accustomed to the new interface. This paper details each of the phases, the success of this methodology as well as the pitfalls experienced.

Jul 11, 2011

By Manuel Rapiman, Ricardo Sepulveda

The feasibility study of Escondida Norte (ENorte), recommended a slope angle design for the Final Pit. But, according to the experience obtained with the slope adjacent to the West wall of ENorte, in which Compañia Minera Zaldívar (CMZ) gained in its phase 4, a slope of similar geotechnical characteristics will be exposed in the West Wall of Phase 1 (Premine) and of the Final Pit, with an interramp angle 53º and with very good stability results. In this regard, Minera Escondida Ltd. (MEL) performed a study of the slope angles for the phases mentioned and according to this delivered the results of this evaluation, the recommendations and/or the necessary conclusions in the design to ensure that the slopes are stable enough and may enable safe operational management of them.

Jan 1, 2006

By Lucas Barcelos Dias

A demanda por materiais ecológicos vem crescendo exponencialmente nos últimos anos. O potencial destes produtos é dado tanto pela versatilidade em seu uso quanto pela sua disponibilidade na natureza. Um dos materiais em expansão é o OSB (Oriented Strand Board), utilizado na vedação do Steel Frame. O trabalho tem como objetivo substituir em três porcentagens 15%, 30%, 45% das tiras de madeira do OSB convencional pela fibra do epicarpo do coco de babaçu (FECB), a fim de melhorar a resistência mecânica. Os resultados obtidos na chapa de 11 mm incorporada com FECB apresentaram resistência a tração entre 15 e 26 MPa e de flexão entre 42 e 75 MPa, tornando assim superiores ao produto encontrado no mercado.

Oct 30, 2017

Laboratory induced polarization measurements were made on representative samples of concentrated sulphide ores from three environments in New South Wales Comparisons were made with the membrane polarization exhibited by an argillaceous sandstone. The sulphide samples showed a strong polarization effect, the magmtude of whIch depended directly on the conductivity of tlIe pore electrolyte.

Jan 1, 1969

By R. P. King

The MODSIM mineral processing plant simultor is used to find optimal combinations of target separation specific gravities in a typical modem coal washing plant. A plant that is set up with these optimal targets can deliver up to 10% more yield at the same ash content as the same plant set up with separation targets chosen by conventional methods. MODSIM is the only simulator currently available that can simulate the liberation of pyrite and other mineral matter during open- and closed-circuit grinding operations. The simulator can therefore be used to assess the benefits of grinding operations in the flowsheet.

Feb 24, 1997

By F. Enslin

Heavy metals and sulphates in acid mine drainage (AMD) can beadsorbed onto bentonite clay, leaving clean water and a heavy metal loaded clay precipitate as products. Due to the toxicity of heavy metals, the clay could not be disposed of safely in the past. A method was thus required to remove the heavy metal content from the clay. Acid leaching was proposed to liberate the heavy metals from the loaded clay. Sulphuric, nitric and hydrochloric acid were considered as lixiviants. Loaded clay samples were leached over a range of pH values from 1 to 3.5 to identify an optimum leaching condition. From the results it was found that metals can berecovered from loaded bentonite clay by means of acid leaching and the optimum pH for heavy metal liberation was found to be 2.5, with uranium as an exception, being optimally leached at a pH of 3. This allows for the possibility of selective leaching. Furthermore, X-ray diffraction analyses indicated that the clay structure did not deteriorate significantly during acid leaching, suggesting that the bentonite could be reused. The treatment of AMD with bentonite clay, and subsequent acid leaching of the clay, is a sustainable solution, and current outcomes could possibly lead to industrial implementation of the process during water purifying and metal recovery from waste streams. Keywords: Acid mine drainage, bentonite, heavy metals.

Jan 1, 2010

By Scott Thayer, Michael Murphy, Natalie Cope, Gabriel Esterhuizen, Anthony Iannacchione, Tim Miller, Brent Slaker

"The Subtropolis room-and-pillar mine extracts the Vanport Limestone (Allegheny Formation, Pennsylvanian System) near Petersburg, Ohio. Strata instability problems associated with excessive concentrations of lateral stress caused the mine operator to implement a change in layout design. This mining method has been identified as a stress control layout, which has been used by other underground stone mines in the past with varying degrees of success. Practical experience has shown that entry headings advance in the direction of the principal lateral stress, producing lower stress concentrations with better mining conditions. It is important to minimize stress concentrations along the mining front, so an arrow-shaped advance is recommended. This technique advances more developments (headings) in a “good” direction and reduces developments (crosscuts) in a “bad” direction. As is expected, the stress control layout enhances the potential for shear failures in crosscuts. It is, therefore, important to focus crosscut engineering interventions that either: (a) lower stress concentrations (for example, an arched roof) or (b) enhance strength of the strata containing the shears (for example, rock reinforcement). This study focuses on observing strata conditions on a regular basis and monitoring the response of this strata to changing geologic and mining conditions through 3D Dynamic LiDAR scans.INTRODUCTIONProject AimsThe Subtropolis Mine is extracting the Vanport Limestone in northeastern Ohio. Since the start of mining in 2006, ground conditions have been significantly affected by excessive lateral stress condition. In some other mining districts with this hazard, certain mine layouts have been shown to lessen the potential for unstable ground conditions. The term “lessen” is used to state the realization that stress concentrations are not eliminated but instead occur in less frequency and intensity, and their locations can be projected.The stress-control mine layout, specifically for large-opening room-and-pillar stone mines, naturally evolved at mines suffering from excessive lateral stress problems. These mines will typically experiment with methods to mitigate adverse impacts, thus developing best practices for their conditions. These practices have evolved into a basic framework for the stress control mine layout. For example, Jack Parker was able to write about personal experiences at the White Pine Mine in Michigan (Parker, 1966, 1973). Various researchers at the U.S. Bureau of Mines (USBM), the Mine Safety and Health Administration (MSHA), and the National Institute for Occupational Safety and Health (NIOSH) have studied the effectiveness of stress-control mine layouts over a wide range of geologic conditions (Emery, 1964; Mark and Mucho, 1994; Iannacchione et al., 2003). While the stress control layout design approach has proven successful in many categories, it can be difficult to implement. For example, excessive stress conditions in crosscuts can put the ground control focused intervention at odds with ventilation and haulage constraints, thus limiting optimal crosscut size, shape, and location. Therefore, more information on the effectiveness of this approach is needed."

Jan 1, 2019

By A. R. Naderian

Laboratory strength and deformation testing of freshly blasted sandstone and claystone overburden from Jeebropilly colliery in Queensland and in-situ plate-bearing tests on four backfills of different ages showed that the bearing capacity of backfill is a function mainly of compaction, not of age. The modulus or stiffness of the backfill is significantly increased by previous loading, in some cases up to threefold. Backfill material experiences some compaction through the passage of mining vehicles, likely to provide a bearing capacity that will support normal construction activities; the limited testing performed suggested that completed backfills are capable of supporting loads of up to 200 kN/m2 while sustaining displacements acceptable for a wide range of residential and industrial uses, but may be susceptible to collapse settlements due to saturation in the long term

Jun 19, 1905

From a vast army of workers to gargantuan machines to immense volumes of material being moved, almost everything about the Port of Miami Tunnel (POMT) project points to tunneling on a massive scale. Almost.The star of this underground and underwater show is a Herrenknecht tunnel boring machine (TBM,) nicknamed ?Harriet? by a local Girl Scout troop. With her 12.9-m- (42.3-ft-) diameter cutting head and a total length of 139 m (457 ft), Harriet is boring through thousands of cubic meters of clay, dirt and sand, which is often mixed with coral and other materials, to create two 1,280-m (4,200-ft) traf?c tunnels connecting Watson Island and the Port of Miami (Dodge Island) beneath Biscayne Bay, FL. But in the midst of all of the oversized equipment and machines, a strong contender for the best supporting nod goes to a relatively tiny machine: the Brokk 400. Bouygues Civil Works Florida crews are using the compact, remote-controlled and electric-powered machine to excavate five cross passages between the twin traffic tunnels. The pas-sages will be essential to the safety of people who drive their vehicles under the bay every day.

Sep 1, 2013

By Jürg Schlumpf

Concrete is one of the decisive construction materials, also for the AlpTransit Gotthard Tunnel. The client has many requirements, and many are the solution possibilities that concrete systems can offer. Cement producers and concrete admixture manufacturers have been challenged to design and test jointly concrete systems for cast and sprayed concrete. The testing operation followed the scenario laid out by the Gotthard AlpTransit Project management?s instructions ?Testing system for concrete mixes.? Various supplier teams have applied for the concrete systems for sections Amsteg/Erstfeld, section Sedrun and/or sections Bodio/Faido and have also followed through with the tests. As was to be expected, the rate of failed mixes matched the level of the requirements. Thanks to this system, it was nevertheless possible to test complete concrete systems for all sections and to get them approved. The joint ventures tendering for the contracts were allowed to include only approved mix designs in their bids. Workability and durability are of paramount importance for cast and sprayed concrete mixes. Durability is influenced by the chosen mix design where binder concept and well-defined water content, i.e., impermeability, are determinant. Aggregates for AlpTransit are to be considered as given. The concrete mix design also determines workability. Because ambient conditions and also requirements with respect to workability are subjected to change, it is necessary that the mix designs include control measures. The choice and number of components for the concrete systems (cement, additives and admixtures) allow adaptation to changing conditions. For AlpTransit such adaptive measures must meet very strict requirements.

Jan 1, 2008

In addressing the need for non-degree tertiary training, let us examine some recent reviews of engineering and geoscience education. The Finniston Report (1) criticised the formation of engineers in the UK and stated that this was largely due to the narrow British conception of engineering as a branch of applied science which militates against an effective marriage between theory and application. It also criticised the system for not giving students sufficient grounding in the synthesis of technical, human and financial considerations within their undergraduate courses. As we all know, this report has led to the restructuring of engineering education in the UK. More recently, a Review of the Discipline of Engineering was carried out in Australia by a committee chaired by Professor Sir Bruce Williams (2). The report stated that: Australia has a fairly good system of engineering education that should be made better. more should be done to develop the communication skills of both staff and students. more attention should be paid to changes in engineering practice and the human element in technology. there is a serious shortage of state of the art equipment in most engineering schools. female enrolments in engineering courses should be increased from the current level of about 7% to 20% by 1997. employers should develop a better understanding of the need for continuing education. staff in engineering schools should develop closer relations with employers of engineers. higher education institutions with engineering schools should give financial and other inducements to staff to increase the proportion of study leave or professional development leave spent working as engineers in the business sector. there is considerable room for improvements in the teaching process and in the development of evaluation schemes for assessing the teaching contributions of staff. In its recent report to the Council of the Institution of Engineers, Australia, the Task Force on Engineering Education(3) makes the following points: managerial, entrepreneurial, professional and interpersonal skills should be introduced and integrated into the undergraduate courses but studied in depth as part of continuing education. the continuing education policy of the Institution should be promoted and strengthened with all engineers required to pursue continuing education. the Institution should develop a comprehensive guide to continuing education available from universities, colleges and other public and private sector organisations.

Jan 1, 1989