Search Documents

By Teena Redhorse, David Tsztoo, Anthony Yu

"Since ancient times, storing and conveying water via underground water systems and tunnels has been touted for its strategic advantages. Underground cisterns and tunnels assured protection of essential fresh water supplies from man made contamination and especially from enemies who would gain an advantage by disrupting an adversary’s water supply in a siege. Modern day engineers do not usually specify tunnels for reasons of avoiding deliberate contamination or siege — however, they are just as enamored with the idea of building tunnels for water conveyances.Such was the case for the San Francisco Public Utilities Commission (SFPUC). The SFPUC provides drinking water to 2.6 million residential, commercial and industrial customers in the San Francisco Bay Area. The SFPUC’s water system includes 257 km (160 miles) of transmission pipelines and tunnels from the SFPUC’s largest reservoir, the Hetch Hetchy Reservoir inside Yosemite National Park, to San Francisco. About 129 km (80 miles) of the system consist of tunnels. A 30-km (19-mile) section of the tunnel network, called the Mountain Tunnel, was thought to be at risk of a catastrophic failure in its concrete-lined section of 18 km (11 miles). For much of the project planning process, a new replacement tunnel was presumed to be required according to the tunnel planners.Originally constructed between 1917 and 1925, the Mountain Tunnel has been in continuous service since 1925. The 30-km (19-mile) tunnel is located downstream of the Hetch Hetchy Reservoir water source in Yosemite National Park, between the Early Intake and Priest Reservoir (Fig. 1). Approximately 18 km (11 miles) of the tunnel is lined with unreinforced concrete. Though the condition of the tunnel was being monitored through water sampling and periodic inspections, there was growing concern that the tunnel lining was at risk of a partial collapse that could interrupt water delivery for up to nine months. The SFPUC was faced with a decision to construct a new bypass tunnel to replace the lined section of the Mountain Tunnel or to rehabilitate the existing tunnel."

Jan 6, 2018

By A. F. Cohen

When location guidelines are followed in choosing sites for fixed point velocity transducers for use in underground coal mine monitoring, mine air turbulence intensities <11% are generally expected at those sites. The objective of this Bureau of Mines investigation to determine the effect of turbulence intensities <11% on vortex shedding sensors and transducers. Measurements were made at velocity levels of interest for underground coal mine monitoring use (?200, ?500, ?1,000, ?1,500 ft/min). The effect of grid-produced turbulence intensities (2% to ?14%) on the output of vortex-shedding air-velocity transducers was less than ±10%.

Jan 1, 1985

By Y. Pan, V. V. S. Vytla, P. Tukkaraja, R. BHARGAVA, S. Jayaraman Sridharan

Panel caving is an underground bulk mining method that utilizes gravitational force for mining massive, steeply dipping, and deep-seated ore deposits at a lower operating cost. To control dust and gas emissions entering the production level during the extraction of ore from the draw points in a panel cave, relatively negative pressure is created in the cave by installing an exhaust fan in the exhaust drift located on top of the cave. Since caving is a dynamic process, the design of an effective ventilation system is a challenging task, and therefore, estimation of airflow resistance offered by the broken rock inside the cave is critical. The complex and dynamic nature of caving also makes it difficult to predict the airflow resistance by using traditional approaches. This study investigates the effect of changes in the bulk porosity of the broken rock on the cave airflow resistance using computational fluid dynamics (CFD) approach. The results show an inverse relationship between the cave airflow resistance and the bulk cave porosity. The pressure-quantity characteristic curves presented in this paper provide valuable information for sizing and operating an exhaust fan used for a mature panel cave ventilation.

May 17, 2022

By K. Mansfield

Spent Pot Lining (SPL) is an unavoidable waste product of the electrolytic process in the smelting of aluminium. SPL is considered to be a hazardous waste in various countries because it contains significant quantities of absorbed fluorides along with traces of cyanide. In 1995, Portland Aluminium undertook the investment of AUD$26,400,000 to construct a Research and Development processing facility at Portland, Victoria, Australia, to treat SPL. Extensive research, development and design were carried out over 5 years prior to the investment decision. This study led Portland Aluminium to install an Ausmelt pyrometallurgical furnace to combust and melt the SPL producing a hydrogen fluoride (HF) laden gas, which was cooled and then converted to aluminium fluoride (AlF3). Both the cooling and AIF3 manufacture were processes developed by Portland Aluminium. Many commissioning, equipment reliability and process problems have been encountered that had not been experienced in the trials at Ausmelt or in the developmental process for the treatment of the furnace offgases to form AlF3. Designs based on anticipated process expectations have had to be re-engineered by the SPL team to ensure plant and operational success. In June 2001, the installation of the final major component - a slag granulation process - was completed. This has produced a vitrified (glassy) slag that is expected to have leachability qualities acceptable to the Victorian Environment Protection Authority (EPA) to allow commercial end uses of the slag material to be developed. Today (September 2001), the smelter has successfully used the fluoride product, namely 65- 70% AIF3, in aluminium production and the SPL plant has significantly increased throughput with expectations to be at annual design rates of 12,000 tonne of SPL in early 2002. "The Alcoa Portland SPL Process" has been technically developed and is a proven process for the treatment and recovery of valuable components from SPL materials.

Jan 1, 2002

By B. B. Letson

The heats of formation of lithium chloride and lithium oxalate were determined with the aid of a Bureau-developed, glass Dewar-type solution calorimeter which uses thermistors as its temperature sensing element. Values obtained at 298.15° K were -98.38 ± 0.54 kcal/mole for lithium chloride and -329.02 ± 0.79 kcal/mole for lithium oxalate, using graphite as the standard state for carbon.

Jan 1, 1965

By Anthony M. Bauer

It is the nature of mining to reshape the landscape. Mining is an earth moving process with many of the same activities associated with the regrading of a site for a shopping center, drainage channel, housing project or ballfield. The difference exists only in purpose and duration of activity. The purpose of mining is to, produce a valuable product. The purpose of regrading for construction of a project is to create a predetermined landscape for a specific end use. In both situations the objective is to move earth materials as efficiently as possible. The question is then raised, if similarities exist, can mining operations be directed to shape predetermined landscapes as an integral part of its earth moving activity. This paper will explore the opportunities and issues of shaping sand, gravel and hardrock construction aggregate sites for productive end uses. It is based upon the premise that, as an earth moving operation, the process of extracting sand and gravel includes an inherent capability to shape productive lands as an integral part of the mining operation. In the course of any mining operation non-commercial materials, including overburden, fines and excess sand are handled to extract and process the commercial products. This activity exists regardless of whether or not there is a plan to reclaim the land. Moving this dirt is a basic operational cost. This cost need not be significantly increased when the material is deposited to shape land rather than be stock- piled just to clear the way for mining the deposit. Moving of dirt to create useable land can be guided by the same criteria used to remove the dirt from the deposit: for example, limiting the- hauling distance. Over a period of time earth handling costs can be reduced by minimizing the need to transport the stockpiled material a second time to the new landform location.

Jan 1, 1984

By F. F. Aplan

"The material known as coal has a highly variable composition. As a consequence, coals show a great variation in their physical and chemical properties as a function of coal rank. The situation is further complicated because the preparation engineer must deal with raw coal, as mined. This is an assemblage of coal, upwards of 30% mineral matter and, typically, several percent pyrite. The kind and amount of the mineral constituents is also highly variable from source to source. A knowledge of coal rank and source location, and the kind and amount of associated impurities, is the first step in evaluating the response of a raw coal to preparation procedures. The raw coal must first be characterized before information from one source can be extrapolated to that of another.INTRODUCTIONCoal is a black or brownish-black combustible solid, derived from a heterogeneous mixture of plant remains and associated mineral matter that have undergone chemical and physical metamorphic changes by biological and geological processes without free access to air. It is composed principally of carbon, hydrogen and oxygen with lesser amounts of nitrogen and sulfur. 'Its exact chemical and physical nature has remained poorly defined, because the term 'coal' refers to a broad range of coalified solids ranging in rank from anthracite to a variety of bituminous coals of differing volatile matter content, sub-bituminous coals, and ending with lignite and brown coals. The variation in chemical and physical properties through these ranks is massive. In summary, Luckie's (1988) assertion is apropos: ""There is no such thing as coal; there are coals"". The coal preparation engineer, and, most especially, those scientists and engineers from other disciplines wishing to work with coal, must constantly keep this admonition in mind because what is true for one coal seam is often not directly applicable to another."

Jan 1, 1989

By Dachun Liu, Xutao Guo, Wenlong Jiang, Baoqiang Xu, Bin Yang, Yong Deng, Heng Xiong

Typical copper dross, the byproduct of lead bullion pyrometallurgical refining for copper removal, mainly contains Pb, Cu, S, As, Sb and Sn etc. In traditional treatment process, copper dross is transformed to be copper matte by smelting with iron scarp and iron pyrite. Here, a new treatment process of converting-vacuum distillation (CVD) was proposed and investigated. Based on this concept, the converting process was tentatively investigated in this paper. The results of element distribution of converting samples showed the sample has three layers. The upper layer is mainly sulfides of lead and copper, the middle layer is mainly copper arsenide, and the lower layer is lead arsenide and crude lead. On the condition of oxygen flow rate 400 ml/min, the converting temperature 1000 °C, the holding time 1 h, the converting time 10 min, the lead copper alloy containing 0.17% S was obtained.

Mar 1, 2018

By H. S. Caldwell

The objective of this investigation by the Bureau of Mines was to develop and test for laboratory use a retort embodying many features required for practical commercial-scale applications of vacuum distillation of metals. A gas-fired vacuum retort was developed comprising a hollow, cylindrical graphite liner encased in a thin shell of stainless steel. The liner prevents the shell from collapsing under vacuum and protects it from corrosion by metal vapors and the molten metal charge. The vacuum-tight shell protects the liner from oxidation and flame erosion. The retort was used to distill zinc from dross and die-casting scrap. More than 99 percent of the zinc was recovered as a condensate containing 99.8 to 99.9 percent zinc. (Atmospheric distillation recovers 95 to 98 percent at a purity of 99.5 percent zinc.) Distillation rates of 50 pounds of zinc per hour were attained at a temperature of 65° C. with pressures ranging between 50 and 100 microns. Distillation at this low temperature is not practicable at atmospheric pressure. Also, the retort is suitable for distilling other volatile metals such as cadmium and magnesium.

Jan 1, 1961

By J. K. Brimacombe

Since the Peirce-Smith converter was introduced to the non-ferrous industry in the early part of this century, there has been a paucity of research on process-engineering aspects of the reactor such as gas injection. This paper reviews studies conducted at UBC over the last decade on gas discharge dynamics, high-pressure injection, bath slopping, oxygen/bath reaction kinetics and out-of-stack heat transfer within the converter. The ultimate objectives of this work have been to extend refractory life and to increase converter productivity.

Jan 1, 1985

By Jerry C. Tien, Yingjiazi Cao

"Coal spontaneous combustion (SponCom) is a natural phenomenon in underground operations, which can either happen naturally or be triggered by human activities. For underground operations, espe-cially in coal, SponCom can happen frequently as a result of air leakage, although its incubation period may vary depends on types of coal and surrounding environment, resulting in uncertainty in control. In China, most of the underground coal operations now use longwall mining method because of its superior safety, high productivity and efficiency. With an increased popularity, there is also an increasing necessity to study spontaneous combustion, its occurrence and management. There have been many theoretical analysis and experimental studies over the past half century hoping to understand the occurrence of coal combustion and its control measures to better understand the occurrence and to design controlling measures to limit the dam-age it causes. In this paper, research on coal spontaneous combustion fundamentals from these three aspects will be reviewed, gaps highlighted and possible directions for future studies. INTRODUCTION The history of anthropic development is the history of human's energy utilization progress. From the first usage of fire, people have been continuingly seeking energy resources on earth. Coal, as an abundant, economic and convenient source of fuel quickly became indispensable and made significant contribution to economic growth worldwide. With technology and societal development, people are becoming more and more coal-dependent, but at the same time, problems of fossil fuel combustion came into sight. In global coal mining industry, spontaneous combustion has now presented one of the most challenging safety issues, it is also believed that it has contributed significantly toward the climate change. It is essential that more effort be invested to examine the cause of SponCom and its control measures. Coal SponCom is a complex process, with both physical and chemical inter-actions among various interrelated factors such as local airflow distribution, ventilation pressure, methane emissions (if any), and physical surroundings underground. With the advent of powerful computers, simulation techniques and af-fordable modelling packages in recent years, significant advances have been made in understanding sponta-neous combustion. But because of the complex nature of combustion and varying underground conditions, there are still areas that need further examining. This paper will focus on illustrating the current research of coal spontaneous combustion and addressing research gaps and future study areas."

Jan 1, 2019

"During his presentation at the 2016 George A. Fox Conference about the history of public-private-partnerships (PPP) in the tunneling and underground construction industries in New York, Vincent Tirolo, Jr., told a story about how, as a young engineer in the late 1960s, he and others pooled money to purchase a calculator for $75 that had the ability to perform sine and cosine functions. That was a big deal in those days and would make their job much easier. Oh how far things have come. Tunnel and underground construction engineers can now virtually map out and plan entire projects before the first shovel ever breaks ground. And the machines that are used to build the tunnels have advanced in ways that could not have been imagined 50 years ago.The calculator is just one example of innovation in the industry and on Jan. 26, more than 400 industry professionals attended the George A. Fox Conference at the Graduate Center of New York (CUNY) to learn more about the next innovations, new tunneling technologies and what the future might hold for the industry. The conference included sessions on contracting models, rescue and fire life safety and new technological developments as well as an international project spotlight presentation from Nasri Munfah about the Eurasia Tunnel, connecting the European and Asian sides of Istanbul, Turkey.The project, also known as the Istanbul Strait Road Tube Crossing project, was named the 2015 Major Tunneling Project of the Year by the International Tunneling and Underground Space Association.The tunnel boring work for the 3,344-m (11,000 ft) long tunnel under the Istanbul Bosphorus Strait was completed in August, heralding a new era in tunneling.Tunnel boring work was launched in April 2014 with a ceremony with then Prime Minister Recep Tayyip Erdogan in attendance. The work was completed on Aug. 22, 2015 with Prime Minister Ahmet Davutoglu participating in the ceremony."

Apr 1, 2016

By G. Vallebuona

Currently, empirical models are used for predicting the hydrocyclone performance in terms of capacity, cut size (d50,c), water split and partition curve. These models, for example those of Lynch and Plitt, have been developed and checked for hydro cyclones with diameters larger than four inches. For smaller diameter hydrocyclones little empirical modelling has been done. This paper reports extended experimental research on small hydrocyclones. For these cyclones, the suitability of existing empirical models has been checked and their accuracy compared. Modifications of the existing models equations are proposed, improving their predictive capability for the small cyclones performance.

Jan 1, 1994

By A M. Garforth

Insurers are hesitant to provide coverage for Open cast Pit side wall collapse, and even the consequent damage to plant and equipment in the pit as well as the resulting interference with the mining operations. After a general introduction to relevant principles of insurance, this paper addresses some of the major reasons for that reluctance based upon the authors? extensive claims experience, examines what limited coverage can still be obtained and looks to the future possibilities. Confidentiality of sources and examples referred to in this presentation is a natural imperative so that a bibliography is not provided but reference is made to relevant sample insurance policy wordings.

Jan 1, 2006

By J. E. Nesset, F. Rosenblum, J. A. Finch, R. Payant

ABSTRACT Under certain conditions of moisture and oxygen, sulphides can spontaneously self-heat. We tested a hypothesis that galvanic interaction between some sulphides can promote self-heating. Galvanic interaction is controlled by the rest potential difference between sulphides and particle size. A series of binary sulphide mixtures was tested. Individual sulphides and mixtures with low rest potential difference did not self-heat, but mixtures of high rest potential difference did. When testing pyrite-sphalerite mixtures, self-heating increased inversely with particle size, with the fineness of the pyrite governing self-heating, indicating the rate-limiting step is the reduction reaction. The results support the hypothesis that galvanic interaction contributes to sulphide self-heating. A possible mechanism based on hydrogen sulphide as an intermediate product is proposed. The understanding gained will be of interest to those involved in storage, shipping, and disposal of sulphides.

Jan 1, 2012

By F. W. Schweitzer

The trend toward development of large low grade ore bodies has accelerated in recent years. It has been estimated within the copper industry that "porphyry" type deposits will provide the bulk of copper production during the next 30 years. It is further estimated that in these deposits the average ore grade by the year 2000 will be 0.25% copper (1). Many of the new porphyry copper discoveries are of such extremely low grade that they are particularly sensitive to small fluctuations in cost variables and copper prices. Because haulage constitutes a major item of surface mining expense, the capability to transport large tonnages of material at increasingly lower unit costs is vital to the profitable operation of many of these mines. High capacity conveyor belts appear to have considerable promise in this area. The heaviest use of high tonnage conveyors has been in the brown coal industry in Germany. In the past 20 years several such installations have proven successful. In addition to the German installations, several other successful systems have been put into operation. Some examples are: The Oroville Dam project in the United States; the tar sand operation in Northwest Canada; the pre-mine stripping and mining of the Twin Buttes Mine in the United States; the Kursk Magnetite &apos;dine in the U.S.S.R.; and the Nchanga Copper Mine in Zambia. Most of the systems mentioned are handling alluvial material consisting mainly of fines. The noteworthy point regarding these installations is their high continuous capacity. One of the largest lignite mines in the world is at Fortuna, Germany, where over 15,700 tons (15,250mt) per hour of overburden is transported on an 87 inch (221cm) wide belt running, at over 1000 feet (305m) per minute.(2). Another example is a 20,000 ton (18,150mt) per hour system for loading iron ore into barges on the Great Lakes (3).

Jan 1, 1976

By Lennart Bergstedt

Boliden Aktiebolag, the prime base metal mining company of Sweden, annually treats some 11-12 million tons of sulphide ore in nine concentrators. Its first flotation plant was established in the early thirties for the complex Boliden ore. Since then, the number of mines and plants has gradually increased. Considerable effort has been devoted to the development of all phases of the technology of ore prospecting, mining, milling, smelting and refining. This has been necessary due to the complex and low-grade ores. The development of concentration has mainly been directed toward the arts of grinding and flotation. During the forties and fifties, open-stage fine crushing followed by two-stage grinding in rod and ball mills with cyclone classification was successfully introduced and used throughout the plants. The increasing cost of grinding media led to studies of an autogenous grinding technique as early as 1945. Basic test work commenced during the early fifties, with a. number of ores tested for pebble grinding. In 1956 a new pilot plant was built, with equipment installed for the continuous testing of pebble grinding and, later, for primary autogenous grinding of run-of-mine ore. The intensive test work showed that pebble grinding was feasible in almost all of the plants. At this early stage of testing, however, the merits of autogenous grinding could not be fully evaluated. As a. consequence the rod mill/ball mill grinding systems were converted to rod mill/pebble mill systems whereever possible. In parallel with the converting of grinding systems the development work concerning the merits of autogenous grinding went on. The major result

Jan 1, 1977

By E. D. Eastman

"The factors that determine the efficiency of reduction of iron oxides by gaseous reducing agents may be considered in two classes; those which effect the equilibrium between the reacting substances end their products, and those which affect the rete of reaction. Both sets are of prectical importance, the former as influencing the maximum possible efficiency and the latter as determining what fraction of the maximum yield may be readily or profitably obtained. In addition, the thermal changes attending the reduction greatly affect the chance of successful industrial application of any such process, and knowledge of them is necessary for the intelligent design of apparatus and control of the reaction. Some aspects of each of these three divisions of the problem are discussed below.I. The Maximum Reducing Power of Fuel Gases on the Oxides of IronsThe gases that heve been considered specifically in this work are coal gas, water gas and producer gas, typical analyses” of which are given in Table 1 Of the various hydrocarbons represented in Table 1, (several being grouped or averaged as C2R4), methane is the only gas assumed to be capable of existence at appreciable pressures under the conditions of interest here. The equilibria in the several systems which may ensue when one of the above gases is allowed to react with the iron oxides, may therefore be represented in the most general case by equations of the type of the following arbitrarily chosen ones:"

Jun 1, 1923

By B. W. Naugle

This report describes the carbonizing properties of coals from the principal beds in Cambria County, Pa. Samples of coals from Upper and Lower Freeport and Upper and Lower Kittanning beds having estimated minable reserves of 50-million tons or more were studied by the Bureau of Mines. Cambria County coals rank either as medium-or low-volatile bituminous. A preparation study indicated that all coals tested in this county, except one sample from the Lower Freeport bed, were responsive to cleaning and would yield a product with satisfactory chemical properties for metallurgical coal. All coals tested from Cambria County yielded strong coke; however, they expand excessively when carbonized singly, and should be used only as minor constituents in metallurgical coking blends when carbonized in slot-type ovens.

Jan 1, 1959

By R. Elliott, C. A. Pickles, J. Peacey

As the nickel sulfide ore deposits become decreasingly viable as a source of nickel metal, increasing attention is being paid to the exploitation of the nickeliferous laterite ores. Attempts to produce a high grade ferronickel concentrate from these ores by pyrometallurgical methods face several challenges, in particular the selective recovery of the highly disseminated nickel from the reduced ore. The current work explores strategies for maximizing the size of ferronickel particles formed in order to improve the selective recovery of the ferronickel by magnetic separation. The effect of various coal, elemental sulphur, pyrite and sodium sulphate additions on ferronickel particle formation and size at 1000°C have been investigated. It has been observed that increased coal additions leads to a moderate improvement in the size of the ferronickel particles, while the presence of any sulphur bearing reagent leads to a significant increase in particle size. The retention of sulphur in the reduced material has also been studied, showing sodium sulphate has the highest retention, followed by pyrite and then elemental sulphur. An inverse trend was observed in the efficiency of sulphur retention on the basis of residual mass of sulphur per unit mass of reagent added.

Jan 1, 2015