Search Documents

By A. Andreas Hejja

Flow of slag and settling of matte in slag resistance electric furnaces are discussed in conjunction with furnace geometries, stirring action of the electrodes, buoyancy and electromagnetic effects. The rectangular electric furnace was regarded as a channel reactor and the mode of slag flow as a channel flow. The flow is affected both by buoyancy and electromagnetic forces, however the effect of electromagnetic forces is minimal. The flow velocity is made up of two components; (i) that developed by the action of the electrodes, and (ii) the bulk flow velocity determined by the smelting rate and the volume of the reactor. Slag samples were taken from various depths of the molten bath and were analyzed microscopically to determine the size and distribution of matte particles, The action of the electrodes was described by a simple mathematical formula indicating a balanced settling rate in the area of electrode action.

Jan 1, 1996

By N. Nemeth

The filter is an apparatus designed to hold the filter medium. At such a medium takes place the entire liquid-solid or gas-solid separation process. Hence, the medium is really the essence of filtration. Yet, the medium, an originally clean porous substance with trapped solids in it, is perhaps the most neglected part of filtration research. Basically three problems prevail at the medium: 1) Penetration of solids and their blinding of the medium and the influence of such blinding on the resistance to flow. ii) The behavior of the medium in long term repetitive filtration. iii) The filter effect phenomenon whereby the flow rate on filtering an apparently clear liquid through a medium decreases with time. This study undertakes to investigate these fundamental processes.

Jan 1, 1968

By Z. S. Shao, X. Z. Li

"Sub-critical crack growth plays an important role in long-term creep failure in brittle rock. Based on micromechanics established by using relationship between micromechanical wing crack growth model and macroscopic strain, and comparing theoretical model with testing results, a method, which applies the theory to real rock, is suggested in this paper. Using this method, properties of creep, damage and progressive failure in brittle rock are investigated. Effects of stress state on creep failure time and steady-state creep rate are analyzed and graphically presented. The results are helpful to support structure design and service life evaluation of underground structures with high geostatic stresses. INTRODUCTIONDuring the long-term operation in underground space with brittle surrounding rock, due to chemical action between pore water and rock, the failure of rock often occurs at stresses below its short-term failure strength, which brings serious effect on the long-term stability of underground structure. Thus, the long-term strength of brittle rock attracted wide interests of scholars around the world. The static fatigue limit was predicted by exponential function that is derived from abundant experiment data of stress level and failure time(Schmidtke & Lajtai, 1985), and similar result by relationship between stress state and failure time was also suggested (Lau & Chandler, 2004; Aubertin et al., 2000; Sangha & Dhir, 1972). According to relationship between steady creep rate and stress state during creep, a critical stress that transforms steady-state creep to accelerated creep was studied and the long-term strength was suggested (Tsai et al., 2008; Ma & Daemen, 2006; Lajtai et al., 1991). Based on the results of experiment in compression, the long-term strength of rock was defined by stress at volume strain reversal. When applied stresses are larger than the long-term strength, the microcracks in the rock will grow constantly, damage of rock will increase and failure of rock will occur finally (Chandler, 2013; Bieniawski, 1967; Brace et al., 1966)."

Jan 1, 2015

By William A. Vogely

HIGH ACTIVITY, continuing the substantial recovery from the slump of 1954, characterized the domestic nonfuels-mining industries during 1956 Income generated in producing nonfuel minerals and mineral products3 increased 9 percent over 1955 as compared with a 6-percent increase for all industries. Thus, the 1956 performance of the mineral industries, while not as dramatic as the 27-percent increase obtained in 1955, continued to exceed the gains of the total economy. Other measures of mineral activity strengthen this conclusion. The index of physical volume of mineral production, presented for the first time as an integral part of this review, reflects significant gains in all major sectors during 1956; and, although the overall increase was diminished somewhat by the steel and iron-ore strike in July 1956, the all-mineral index (including fuels) reached a new high.

Jan 1, 1958

By Carl Heising

Longwall workings in the Federal Republic of Germany are situated in deep depths. Coal deposits are characterized by a sequence of many seams and manifold geological disturbances. Hence result special requirements on the layout of workings, the methods of coal getting, supports, mine ventilation and dust control. As for the application of dust control the large quantities of fresh air and, this, the high air velocity and the limited water contents in the run-of--mine coal must be taken into consideration. The principle of our methods of dust control is to avoid, if at all possible, the development of dust and, if this is not possible, to suppress the dust even during its development. In nearly all coal faces, the method of water infusion prescribed by our Mines Inspectorates is applied. Continuous water in- fusion is preferred. For water infusion in the coal face, intensive developments as to the process and as to the tools and apparates to be applied were done. The German coal mining industry differs between cutting coal getting and stripping coal getting. Water spraying to the tracks of coal ploughs as well as internal and external water feed to the loader required special activities of further development in past years. There are possibilities to still improve such methods in future. A new important field of applying dust control developed from the application of powered supports. In this field, water spraying prevails. Wet methods of dust control are prefered also in the conveying and loading of coal and at through-flow crushers, however, as far as possible, combined with a covering of the working points where dust develops. Devices for the collection and sedimentation of dust, so-called dust exhausters, are used also with crushers In advanced headings, dust control is performed solely by water. Gateroads kept on or behind the coal face line call for new methods of dust control which are at present under development.

Jan 1, 1980

By C. Michael Morgano

Static tests are costly and time consuming, so they are not always the best answer [ ]

Jan 1, 2005

By Dirk van Zvl

The design of cover systems for reclamation schemes in tailings requires estimation or determination of tailings materials properties such as compressibility, shear strength and consolidation characteristics. It is very difficult and expensive to obtain truly undisturbed tailings samples for laboratory testing. In situ testing methods have been developed for economically obtaining large amounts of information. Two of these methods are described, the piezocone and the flat plate dilatometer. Both of these methods provide a rapid means of detailed material identification in a nearly continuous fashion for the entire depth investigated. The equipment is described and typical data from a uranium tailings impoundment is presented. The results are compared and the advantages and disadvantages of these methods are discussed.

Jan 1, 1984

PRESIDENT MOSES.: The meeting will please come to order. Will you kindly state your names prior to making any statements, in order that we may deep the record straight? The first paper this morning is a joint one on vocational training, by D. W. Rockey, H. A. Tiemann and Wm. Moorhead. Mr. Rocdey. (Applause.) D. W. ROCKEY (State Superintendent, Industrial Education, Santa Fe, New Mexico) (Mr. Rocdey's notes not received in time for publication.) MR. TESCHER: I would like to ask you, Mr. Rocdey, you say you gave the Phelps-Dodge Corporation financial assistance; to just what extent was the State obligated, and how much assistance was given, etc.?

Jan 1, 1927

By S. N. Monteiro, C. M. F. Vieira, A. P. N. M. de Sa, J. P. D. Vitorino

"This work has as its objective to characterize an ash waste and to evaluate its incorporation into a clay to produce bricks and roofing tiles. The waste is a type of fly-ash resulting from the incineration of a selected part of urban garbage, which is basically constituted of organic matter and plastics. The waste was submitted to mineralogical and chemical characterization. Compositions were prepared with incorporation of the waste in amounts of up to 20wt.% into athe clay. Rectangular specimens were prepared by extrusion and fired in a laboratory furnace at 900°C. The physical and mechanical properties evaluated were: linear shrinkage, water absorption and flexural rupture strength. The results showed that the waste is predominantly composed of quartz and calcium compounds. The incorporation of the ash was deleterious to the evaluated properties of the clay. It is suggested that the incorporation should be made in amounts below 5wt. % to avoid deleterious effect in the mechanical strength and water absorption of the clayey ceramic.IntroductionThe world attention has turned to a subject of great concern today, the production and disposal of large amounts of industrial wastes as well as wastes of various sources. When deposed in an unsuitable place, these wastes can cause considerable harm to human health and to the environment. Our planet suffers with air pollution, groundwater and soil contamination as well as silting of rivers and lakes with the growing amounts of our society wastes.The recycling of waste materials is of great interest to the industries, mainly due to the environmental agencies legislation. One of the practices for correct disposal of these wastes being investigated is to incorporate into red ceramics, such as bricks and roofing tiles. The natural variability of the characteristics of the clays associated with the relatively simple processing techniques and also the low performance required for the products allow the presence of relatively high levels of impurities in clayey ceramics."

Jan 1, 2011

By S. P. Kinney

[The blast-furnace operator is often confronted with the problem of determining the size of the materials which are used in the furnace burden. The statement is heard that the coke is larger or smaller or that certain ore is finer than that previously used. A screen analysis of the materials used gives a measure of the different sizes of materials in an aggregate. When one is fine and the other is coarse, the difference is obvious; but when the materials are of similar sire, it is more difficult to estimate the degree of finances or coarseness. In considering raw materials it would be desirable to be able to judge the size of the radio ideal materials entering the furnace and the burden as a whole, by one representative value, such as the average size of particle. Previous work by Perrott and Kinney3 developed a method for measuring the average size of particle in a mass of finely ground materials, and an attempt will be made to apply this method to the materials included in the blast-furnace charge and to the entire burden.]

Jan 1, 1930

By H. NORTON JOHNSON

THE oil industry in California during 1929 reached new heights and new depths in the discovery and development of the oil resources of the State. The discovery of new fields, and more especially the discovery and development of deeper prolific sands in known fields has, for the first time in its history, brought the potential production of completed wells within the State to over 1,000,000 bbl. oil per day. Constant improvement in equipment and technique has made possible economic development to depths unheard of but a few short years ago. Commercial production from a depth of over 4000 ft. was considered quite an accomplishment in 1923 when the Meyer sand at Santa Fe Springs was developed, and when later oil was successfully raised from this depth.

Jan 1, 1930

By Diler Katircioglu-Bayel

This manuscript aimed to examine the impact of operating parameters on the wet grinding of talc in a vertical-type stirred media mill. Within the scope of the research, the effects of operating parameters including media filling ratio, solid mass fraction, grinding media size, and grinding time were studied. The findings were assessed based on the product particle size (d50, d10), surface area (Sw), and energy consumption (Em). As a result of the present research, the following optimum grinding test conditions were determined: 65% media filling ratio, 40% solid mass fraction, 1 mm grinding media size, and 120 min grinding time. After determining the optimum grinding conditions, the Box–Behnken statistical design was used to determine the effect of parameter interactions on the d50 size. The media filling ratio was found to significantly affect the decrease in d50 compared to the other two parameters. Furthermore, the minimum d50 size was also achieved under optimum grinding conditions.

Aug 12, 2020

By Larson. William

What is Lunar In-Situ Resource Utilization (ISRU)? ISRU involves any hardware or operation that harnesses and utilizes ?in-situ? resources to create products and services for robotic and human exploration In-Situ Lunar Resources ???Natural? Lunar Resources ??Discarded Materials Lunar ISRU Products and Services ??Excavation, Site Preparation, and Outpost Deployment/Emplacement ??Mission Consumable Production ??Outpost Growth and Self-Sufficiency Benefits of ISRU ??Increased science and exploration hardware (instead of consumables) ??Increased safety, crew exploration time, and self-sufficiency ??Technology spin-in/spin-offs help recycling on Earth & space economy

May 1, 2009

By C. H. Zhou

Cryogenic grinding of Printed Circuit Board will bring less pollution, reduce energy costs, smaller particles, regular particle size, efficient process, separation various materials due to different fracture toughness. Systemic studies of recycling discarded Printed Circuit Board (PCB) by low-temperature modification and cryogenic grinding have been made in this paper. Firstly test mechanical property of PCB at different low-temperature, including impact strength, flexural strength, and shear strength. Do experiment on the power consumption of different cooling temperature, The results show that the average power consumption is lower between -30? to -60? and the average power is decrease in evidence at -30?. Use ZKB type double roll shear crusher to crush PCB to 20mm×20mm particle size, in a temperature range of -10 ~ -30? Used R type mill to grind sample to minus 3mm under different working condition, the average power consumption is decrease in evidence from -10 ? to -30 ?, power consumption is the lest at rotational speed is 1180rpm.

Jan 1, 2014

By Charles A. Taschereau

Burkina Faso ? Formerly known as Upper Volta; Country is landlocked and dry (Sahel sub-Sahara zone); ? Among poorest countries in the World, according to the United Nations Human Development Index (in 2005, 178 out of 179 countries; in 2009 173 out of 179); ? Population 13,9 Millions; Life expectancy is 51.4 years; Fertility rate 6.47 children/woman; Average age is16 years; literacy rate 23.6% and GDP per capita $1,213; ? French is official language; Politically stable country; very low criminality rate; corruption level low. Multiparty elections since early 90s; Legal and political systembased on French civil law system; ? Country just opened a few years ago to International mining companies, with a new mining code and investment code; ? No experienced labour; ? All new codes and laws; no established practices; Very limited economic development, mining is already main product of exportation and the country will become with Essakane a mineral economy (over 50% of total exports from mineral sources);

May 1, 2010

By Musa Karakus

Ceramic build-ups are synthetic mineral deposits formed in critical locations in or near the throats of inductor units in channel induction furnaces, the preferred melting and holding furnaces used in iron foundries. The build-ups are undesirable because they slow down melt circulation, increase power consumption and cost. and decrease the quality of the metal. This study involved the determination of the mineralogy of build-up samples and the quantitative measurement of phase abundance in those build-ups by cathodoluminescence microscopy. These undesirable deposits usually are hard and dense and contain variable amounts of entrained metallic iron. The non-metallic phases dominantly consist of oxides and silicates of several refractory elements, AI, Mg. Ca, Si, and Fe. Minor amounts of the sulfides of Ca. Mg, Fe and REE elements, especially Ce and La. and the oxides and silicates of Ce and La elements are locally present in the build-ups. The build-up samples were found to be ideally suited for study by cathodoluminescence, which has provided an easy means for rapid re-cognition of the phases present in the build-ups. The phase compositions were determined by electron microprobe analysis. The phases identified and their characteristic cathodoluminescence shown in the ceramic build-up samples were: spinel (bright green, blue-green, and red). forsterite (red and purple), periclase (dark reddish-brown, blue. and orange), corundum (red, blue, orange, and white), anorthite (yellow, yellow-green, blue, and blue-purple), hibonite or calcium hexaluminate (dark green), mullite (dull red-brown), gehlenite (deep blue), silica(dark brown, pink, purple, red. and blue), monticellite (light violet blue and light pale yellow-orange), silicon carbide (orange), oldhamite (bright yellow and orange). Ce-La silicate phases (purple), and glass (orange, dull red, and purple). Non-luminescent phases were: hercynite, Fe-oxides, Ce-La-oxides, Fe-sulfides, and metallic iron.

Jan 1, 1989

By L. F. Heising

Ten composite samples of Mesabi Range nonmagnetic taconite from the Hibbing, Minn., area were evaluated by flotation and by reduction roasting-magnetic separation to determine their potential as a future source of iron are. Only one of the composites yielded concentrates that could be considered marketable, using as a criterion a 10-to-1 iron-to-silica ratio. Cursory petrographic examinations of all 10 composited samples and a detailed mineralogical study on 1 sample suggest that unfavorable mineralogical associations between iron and gangue minerals are responsible for their poor beneficiation characteristics.

Jan 1, 1967

By W. F. Faragher

The principal equipment in the catalyst plants at Ludwigshafen-Oppau was inspected and is presented in the form of flow sheets for the manufacture of four of the principal catalysts. The equipment is in many cases of special design rather than stock items that was built by the company and modified in the coarse of the growth of the high-pressure synthesis of hydrocarbons in Germany. It is believed that if the manufacture of catalysts were to be undertaken elsewhere, the selection of equipment for the operations involved could be made successfully from the guidance furnished by this rather general report. Five additional catalysts are described, also. II. CATALYST 5058 FROM FRESH TUNGSTIC ACID In a supply tank of about 2,000 liters capacity, 500 kg. of tungstic acid (W03.H2O) that contains about 92-93 percent of W03 is dissolved at 60-70° C. in 1,500 liters of mother liquor. The solution is-effected by stirring for about 1-1/2 hours. The mother liquor is obtained from a previous, lot of catalyst and is first adjusted to a concentration of 13 percent 1H3 by passing in gaseous ammonia. The solution is allowed to stand without stirring for 1 hour, then is pumped into the saturating vessel through a cloth filter (three-quarters hr. to one hr.). The saturator is purged with H2S and thereafter the solution, which has been cooled to about 75° C., is heated in an atmosphere of hydrogen sulfide with stirring to about 70° C. This charge is slowly cooled to 50°, and then more rapidly to about 20° C. (time of cooling 6-7 hours).

Jan 1, 1946

By Thomas V. Falkie

Mining and exploration, in the year 1971, can be characterized as a year of politics and the beginning of an era of legislation. Certainly the activities of our state and federal lawmakers and international politicians over-shadowed technical developments, which are outlined in the following pages. The nationalization of the Chilean copper industry was the most far-reaching event of the year. Not only will it have an effect on international metal trade, but the nationalization will also affect the major mining companies in such a way as to cause strategic, managerial and technical adjustments in metal mining and exploration efforts in other parts of the world.

Jan 2, 1972

By R. J. Stevens

THE Roan Antelope Smelter commenced operations in October, 1931. As originally designed, its equipment consisted of one reverberatory furnace, 120 X 25 ft, two Peirce-Smith converters 12 X 20 ft, and one straight line casting machine. Since that time the following additions have been made: One reverberatory furnace 120 ft X 28 ft (1934) One reverberatory furnace 95 ft X 28 ft (1943) Two 12 X 20 ft Peirce-Smith converters (1934 and 1938) One 13 X 30 ft holding furnace 6 (1938) One straight line casting machine and 2 ladle tilting quadrants (1934) The metallurgy of the smelting process is comparatively simple. However, there are several features of operation which are uncommon to most copper smelters: (1) The high grade of concentrate treated; this has always been about 50 pct copper. (2) The high flux burden on the charge. This is necessary because of the deficiency of bases'in the concentrate and the high alumina content of the concentrate. (3) The frequent necessity of adding coal to the furnace charge to control the matte grade. (4) The high grade of matte produced. This has led' to unusual converter problems. From the commencement of operations, the ore mined has come from the Roan Basin orebody. The concentrate produced from this ore consists mainly of chalcocite and shale with small proportions of other copper minerals. As mining operations extend to the Roan Extension orebody, the proportions of bornite and chalcopyrite in the concentrate will increase with a corresponding decrease in the copper content of the concentrate. Because of the concentrate grade the capacity of the reverberatory . furnaces in terms of tons of copper produced per ton of coal burned is high.. This ratio is usually over 2.2, and on especially favourable runs has reached 2.6. Reference to Table , shows that the iron content of the concentrate is unusually low. Only part of this iron is available for slag formation, the balance going to the matte. To make up this deficiency in bases, limerock is added to the furnace charge. This flux ensures a slag that is of the correct silicate degree, is sufficiently fluid, of low specific gravity, and it counteracts the thickening effect of the alumina present. An ample supply of flux is obtainable from Ndola, 2 2 miles distant by rail. Although the reverberatory slag has a high copper content, the slag fall is low and the copper loss in the slag now rarely exceeds 1.0 pct of the total copper charged. The blister copper shipped is of such purity that only one fire refining operation has been necessary to produce a wirebar with properties comparable to electrolytic copper. Bismuth has always been the most troublesome impurity and consequently the problem of its control in the finished product has been of prime importance. Practically none is removed in the reverberatory furnace. The bulk of the elimina-

Jan 1, 1947