Search Documents

By N. Raeis Hosseiny, S. H. Bassir

"Chador-Malu iron ore is one of the most important iron mines of Iran.About 98 percent of Fe in the ore is in shape of Magnetite, Hematite, Martite, aqua oxide of Iron and the other irons are with ferrous silicates, actinolite, cholorite and ferrous dolomites. 1% of Fe has replaced in pyrite. The phosphor distribution in the ore is non-hemogenous and its average in the whole of the deposit is 94%. It is in shape of Apatite.This mine contains considerable phosphor, which makes it useless for metallurgical uses. At this mine the phosphor is reduced in the iron ore at two steps. At the first step, magnetic part of the ore is separated from the gangues and phosphors by magnetic separator. At the second step, the ore is enriched by the flotation methods. Experimental flotation methods to obtain the optimum conditions are as follows:• Effect of Starch as Hematite depressant with ATRAC as Apatite collector• Effect of Sodium silicate as Hematite depressant with ATRAC as Apatite collector• Effect of ASAM as Apatite collector with Sodium silicate as Hematite depressant• Effect of ATRAC (BEROL) as Apatite collector with Sodium silicate as Hematite depressant• Effect of ASAM & ATRAC mixture as Apatite collector with Sodium silicate as Hematite depressant• Effect of Kcarbonate as pH-modifier• Final test to Optimize pH, Collector, DepressantAt this research we have found the optimum circumstance of the flotation of Chador-Malu iron ore in order to decreasing phosphors of iron oxide and floating of Apatite to make pure Hematite.To reach the optimum conditions, some tests were done with different amounts of pH, collector and depressant. The results are as follows:"

Jan 1, 2003

Discussion of "The Ordering Transformation in Titanium-Aluminum Alloys Containing up to 25 at. pct Aluminum" by F. A. Crossley, Trans, TMS-AIME, 1968, vol. 242, pp. 726-30. Dr. Blackburn, in his response, pointed out that the c/a ratio of the Ti-26 at. pct A1 alloy quenched from 900°C is 1.6006 and not 1.5965 as plotted in Fig. 19. An error in transcription was made in preparing Table V of Ref. 1 (F. A. Crossley, Trans. TMS-AIME, 1966, vol. 236, p. 1174). The corrected Fig. 19 strengthens rather than weakens the argument that a martensitic transformation occurs in alloys containing from 15 to 18 at. pct Al. A Study of the Factors Which Influence the Rate Minimum Phenomenon During Magnetite Reduction, by P. K. Strangway and H. U. Ross, Trans. TMS-AIME, 1968, vol. 242, pp. 1981-88. Page 1883 Reverse Figs. 5 and 6. Sigma—Its Occurrence, Effect, and Control in Nickel-Base Superalloys, by J. R. Mihalisin, C. G. Bieber, and R. T. Grant, Trans. TMS-AIME, 1968, vol. 242, pp. 2399-2414. Pages 2403, 2407, and 2414 Arrows should appear on Figs. 4 and 9; a sigma is missing from Table IV; line 2, page 2414, change "case" to "cast". These are published correctly in the bound volume. Index, December Issue There were a few omissions in the Author Index. These have been corrected and published properly in the bound volume.

Jan 1, 1970

By Dave Deglon

"The Western Cape Mineral Processing Facility (WCMPF) is a collaborative educational initiative between the Departments of Chemical Engineering of the University of Cape Town, the University of Stellenbosch and the Cape Technikon. The primary objective of the WCMPF is to facilitate the education, development and graduation of suitably qualified engineering graduates and diplomates for the mining industry. The WCMPF consists of academics and Technical Officers in the Departments of Chemical Engineering of the three tertiary institutions. The Technical Officers are usually metallurgists, with several years of industrial experience. The main objective of the Technical Officers is to improve the practical education of mineral processing students. In addition, the Technical Officers are responsible for organising an annual mineral processing student field trip for students from all three tertiary educational institutions. In recent years the WCMPF has embarked on a number of additional initiatives aimed at improving the quality of mineral processing education. These include the development of several new pilot plant practicals, an initiative in pyrometallurgy, the introduction of novel ‘end to end’ or ‘integrated’ practicals and the use of mineral processing simulation packages to complement the practical training.The WCMPF has been functioning for well over a decade and, by virtue of this, might be considered a successful collaborative educational initiative. The WCMPF has played a key role in the education of over five hundred mineral processing graduates and diplomates. During this time period, the WCMPF has gained a body of internal knowledge which might be of benefit to other educational institutions, viz."

Jan 1, 2003

By Y. C. Han

The advances in seismic design considering soil-structure interaction or soil-pile-structure interaction are described using a substructure approach. The nonlinearity of soil is considered approximately using a boundary zone model with non-reflective interface, and computer programs are available for practical applications. The validation of model is confirmed with dynamic tests on piles in the field, and the results for a single pile are used to compare with the predictions in this study. The liquefaction for sand soil layer can be accounted for, and a case of liquefaction is discussed. Two practical examples are examined, a vacuum tower structure supported on foundation of steel pile group and a table top structure supported on foundation of concrete pile group. To illustrate the effects of soil-pile-structure interaction on the seismic response of vacuum structure, different base conditions are considered, rigid base, i.e. no deformation of the foundation; linear soil-pile system; and nonlinear soil-pile system. The method introduced can be applied to the design of tall buildings, bridges, industrial structures and offshore platforms with soil-pile-structure interaction under seismic or dynamic loads.

Jan 1, 2010

By Noan Tonini SImonassi

Fibras de rami (Boehmeria nivea) estão entre as lignocelulósicas naturais com potencial para utilização em compósitos poliméricos. O presente trabalho avalia a resistência ao impacto deste tipo de compósito. Corpos de prova normalizados foram confeccionados com percentuais de até 30% em volume de tecido de rami alinhadas ao longo de todo o comprimento. As fibras foram embutidas sob pressão em matriz de resina poliéster do tipo ortoftálica curada à temperatura ambiente por 24 horas. Os corpos de prova foram ensaiados em pêndulo de impacto Izod e as superfícies de fratura analisadas por microscopia eletrônica de varredura, MEV. A resistência ao impacto aumentou exponencialmente com a quantidade relativa de tecido de rami reforçando o compósito. Este desempenho foi associado à dificuldade de ruptura imposta pelas fibras bem como ao tipo de trincas resultantes da interação tecido de rami/matriz de poliéster que ajuda a absorver a energia do impacto.

Aug 17, 2017

By L Soebari, W Sunyoto

The Wabu Ridge Gold Skarn deposit is located at elevations of up to 3100 metres above sea level, in the Central Highlands of Irian Jaya, Indonesia, 35 km NNW of the Grasberg porphyry deposit. Wabu is a grass-roots discovery in an area with no previous gold mining history or record of gold mineralisation. A geological resource of 117.26 million tonnes at an average grade of 2.16 g/t Au (1.0 g/t Au cut-off) has been defined to-date. Mineralisation is hosted within a skarn occurring along the southern boundaries of the Late-Miocene age monzonite-diorite Pagane intrusive complex. The intrusive complex occurs in the footwall of a major EW structure, the Derewo fault, which displays sinistral strike-slip and reverse fault movement. The Derewo fault separates Derewo metamorphic units to the north from platform sediments of the Australian craton to the south. The skarn has a strike length of 6 km and is up to 1.5 km wide. It is developed within calcareous shelf sediments of the Tertiary New Guinea limestone group and is dominated by prograde garnet development. Gold mineralisation was deposited during retrograde alteration and is directly associated with arsenophyrite and bismuth minerals. Retrograde alteration is distinguished by a sequence of clinopyroxene , magnetite, epidote and hornblende, biotite and chlorite and lastly carbonate. Gold is associated with the biotite/ chlorite phase together with sulphides and precipitated as the result of fluid mixing. The Wabu Ridge Gold Skarn deposit was identified in April 1990 during a regional program of helicopter assisted stream sediment sampling of -80 mesh (180 microns) fraction and panned concentrate sampling. The initial discovery sample site was situated 15 km down stream from the deposit and returned 1.49 ppm Au for the stream sediment sample and 138 ppm Au for the panned concentrate sample. A regional airborne helicopter magnetics survey, conducted in early-1992, helped defined the main magnetite associated skarn zone and the extent of associated igneous rocks. Detailed follow-up commenced in May 1992 and consisted of detailed mapping, soil sampling and ground magnetics prior to drilling the first hole in October 1992. Drilling to-date has delineated a contained geologic resource of 8.1 million ounces of gold and potential exists for a larger resource.

Jan 1, 1999

By Z Li, Z Yan, T Htet, S Zhang

During the pyrometallurgical processes, a substantial quantity of high-temperature ironmaking and steelmaking slags, generated at temperatures ranging from 1400 to 1600°C, is wasted, as the heat contained in these slags is released into the environment during the tapping process without effective utilisation. On the other hand, a significant amount of energy is required to reheat the cold materials for the manufacturing of glass and mineral-wool, often necessitating the addition of high-silica materials to facilitate the production process. In this study, an innovative approach is presented to harness the heat present in molten metallurgical slags to directly produce new raw materials for glass and mineral-wool manufacturing while simultaneously reducing energy consumption and mitigating CO2 emissions. The theoretical amount of waste glass that can be effectively added in the process has been estimated via thermodynamic calculation. Experimental assessments were conducted to examine the impact of high-silica waste materials on the dissolution, melting and fluidity. Potential recipes for glass and mineral-wool manufacturing were suggested and an assessment of the energy savings, and reduction in CO2 emissions with manufacturing of glass and mineral-wool using this innovative approach were included. It was determined that the processes could lead to a reduction of over 26 kg of CO2 emissions per 100 kg of new material used, primarily due to the utilisation of heat from slag and the accelerated smelting process.

Aug 21, 2024

By Matthew Geary, Stephen J. Marino, Jordan A. Schreiner

"INTRODUCTION Project Overview The Southeast Collector (SeC) is a new 15km long 3.0m internal diameter wastewater tunnel designed by Hatch Mott MacDonald (HMM) that twins the existing 2.6m diameter York-Durham Sewage System (YDSS) tunnel. Both sewage tunnels are located north of the City of Toronto in Ontario, Canada. The SeC provides much needed conveyance capacity for the rapidly growing York Region population, supporting development until 2036 and increasing sewage system security (Hatch Mott MacDonald and AECOM 2011). Construction of the SeC will also permit flows of the twinned section of the YDSS to be bypassed in order to clean, inspect and carry out any essential maintenance within the YDSS tunnel. Although owned and operated by York Region, the SeC spans two regional municipalities beginning upstream from the intersection of Ninth Line and Rouge Bank Drive in the City of Markham in York Region to the downstream Finch Avenue and Valley Farm Road intersection in the City of Pickering in Durham Region. See Figure 1 for the SeC and YDSS alignment. The project includes 19 shafts and chambers with depths ranging from 8 to 48m in addition to seven facilities supporting the operation and maintenance of the sewer. The construction contract was awarded to Strabag Inc. in July 2011 for $291M CAD. Construction Management services were provided by a joint venture team of Hatch Mott MacDonald and AECOM. Existing York-Durham Sewage System The YDSS tunnel was completed in 1979 and was constructed using an open shielded TBM with ribs and lagging temporary support, followed by installation of a 380mm thick unreinforced cast-in-place (CIP) concrete final lining. The YDSS sewer system has numerous connections that accumulate flows from various urban areas within York Region. The section of the YDSS twinned by the SeC flows under gravity conditions and had been putting a strain on the municipality’s potential for population and development growth having reached its maximum capacity of 420 ML/d. According to the York Region’s Water and Wastewater Master Plan, the existing YDSS would not have been able to handle wet weather flows past 2016 (Genivar and XCG Consultants 2009). The dependability of this section of the YDSS is also of concern because it is the main and critical connection between the sewer systems upstream and the downstream Duffin Creek Water Pollution Control Plant (WPCP)."

Jan 1, 2016

By Cleo Griffith Rall

The method for determining the effective porosity, of oil- and gas- bearing sand described in this report is a development of an earlier method devised by Bureau of Mines. The apparatus has been improved and made more convenient to use, but the procedure has been in use for many years without essential changes. A tabulation at the end of the report gives the results of more than 2,000 porosity determinations for oil sands in the fields of 13 states. A selected bibliography of articles containing descriptions and evaluations of various methods of determining porosity Is a. part of this report. The method was devised and developed at the Petroleum Experiment Station at Bartlesville, Okla., as part of the Bureau's research on fluid-energy relationships and ,on methods of improving the recovery of crude oil from underground reservoirs.

Jan 1, 1949

By S. K. Kawatra

Many mineral oxide and multi-component oxide (basalt) specimens break down into powders upon expo-sure to sodium vapor at elevated temperatures for extended times. This paper examines several possible mechanisms of oxide breakage by sodium vapor, both experimentally and from a thermodynamic viewpoint. The oxides for which reduction by sodium was thermo-dynamically favorable all exhibited some degree of fragmentation. The oxides which were not favorable for reduction by sodium did not exhibit fragmentation, with the exception of rutile, a titanium oxide. The rutile fragmentation was caused by the reduction of iron that was in solid solution in the rutile crystal structure.

Jan 1, 1995

By M. Clair Smith

The Bureau of Mines investigated the Rip Van Winkle mine, which is about 25 miles northwest of Elko, Nev., from October 1942 to February 1943 to determine possible resources of lead-zinc-silver ore. The property is owned by the Rip Van Winkle Consolidated Mining Co., which maintains its offices in Salt Lake City, Utah. Ore was discovered in the 1860's, and active mining was carried out intermittently until 1939, when the Rip Van Winkle Consolidate Mining Co. acquired the property. This company equipped and developed the mine, erected a flotation mill, and operated on a 65-ton daily basis. The ore is mined from veins, mineralized faults, and replacement deposits of wall rock. The country rock comprises cherty shale, granite, porphyry, intrusive breccia, and breccia, and brecciated shale. Mining operations were carried down to the 700-foot level. The Bureau of Mines drilled 5 diamond-drill holes, totaling 1,084 feet, from the 600- and 700-foot levels, excavated a 250-foot surface trench, and took 26 underground samples. The ensuing sections note the location and physical features of the district, mention the equipment, and specify the property and ownership. The history of the mine is briefed, and the geology, mine workings, and plant are described. The work performed by the Bureau of Mines is summarized and supplemented in detail by assay maps, logs of diamond-drill holes in appendix A, and by tables of sample analysis in appendix B.

Jan 1, 1949

By J. W. Eckerd

The crushing of chestnut-size (1-5/8 by 13/16 inch) Pennsylvania anthracite in four commercial crushers (impact) jaw) hammer-mill) and gyratory types) was studied by the Bureau of Mines to determine which could produce the largest proportions of buckwheat Nos. 1 and 2 sizes (9/16 by 3/16 inch). Single pass dry and wet crushing techniques and the effect of stage crushing were evaluated. Calculations were made to show the effect of closed-circuit reduction on production rates and yield of the various sizes. The data show that the gyratory crushers produced the greatest percentage of the desired sizes. A ring-type hammer mill produced the greatest tonnage of buckwheat No.1 and rice (14.9 tons per hr.) during dry grinding tests) but the yield of these sizes was only about 55 percent) as compared with 62 to 70 percent for the gyratory crushers. The impact and jaw crushers produced the smallest amount of buckwheat and rice and the largest quantity of oversize material.

Jan 1, 1960

By William R. Yernberg

The combined 80th Annual Minnesota Section of SME Meeting and 68th Annual University of Minnesota Mining Symposium was held April 17 and 18, 2007, in Duluth, MN. About 350 mining industry professionals attended the conference, including engineers, executives, mining managers and suppliers from the United States, Canada, Australia, Finland and Brazil. This year’s theme was “Consolidation – Growth – Technology.” The 80th Annual Minnesota Section of SME meeting included concurrent technical papers sessions, a keynote session that featured two distinguished speakers and a general managers session in which taconite mine operators provided updates on their operations. The Minnesota Section meeting also offered an SME short course titled “Control the Feed, Control the Mill.” More than 50 individuals at-tended the short course.

Jan 1, 2007

By J. S. Hansen

In support of its objective to conserve mineral resources by minimizing premature failure of materials, the Bureau of Mines conducted a cooperative study with the U.S. Department of Energy on the erosion and abrasion resistance of hard materials for valves in coal conversion systems. This report describes a newly developed erosion-testing apparatus and presents data on the erosion resistance of over 200 materials. Erosion resistance of most metals was comparatively low. In contrast, ceramics and cermets such as B4C, WC, SiC, Si3N4, and TiB2, when fabricated to minimize porosity, displayed greater than five times the erosion resistance of metals. Coatings such as boron diffused into Mo and WC, chemical-vapor-deposited TiCN, and electrodeposited TiB2 were highly erosion resistant if applied in thicknesses ranging from 60 to 75 µm. Erosion resistance of cemented carbides was inversely related to metal binder content.

Jan 1, 1979

NIOSH research has focused on the monitoring and the control of methane levels in active mine workings. Response times for instrumentation using catalytic heat-of-combustion sensor technology were evaluated. NIOSH research has modelled the flow of methane gas onto long-wall faces and gobs, developed engineering controls to limit methane levels during mining, and designed coalbed and gob degasification systems. Available methane control systems have been challenged by recent developments in longwall and room-and-pillar mining systems. This includes increased face advance rates leading to increased productivities, increased longwall panel sizes, and the generally deeper workings of U.S. coal mines. The potentially violent nature of any underground explosion or ignition requires the measurement, control, and reduction of methane emissions into the mine environment for continued worker safety.

Jan 1, 2008

By J. M. Hong, H. K. Zheng, R. Hu, C. B. Zhou

The Jinping-I double curvature arch dam, located in the middle reach of the Yalong River and with a maximum height of 305 m, is the world highest dam of the same type that has been completed. Since the second and third periods of the reservoir impounding, after which the reservoir water level was raised by about 200 m, a significant amount of leakage was observed out of the drainage holes deployed in the lowest drainage tunnel at the left-bank abutment at EL. 1595 m, with a pressure of 0.3 MPa at one typical hole when it was blocked. In this study, a number of analyses including water quality analysis, digital borehole imaging, tunnel geological mapping and in-situ groundwater monitoring were performed to investigate the source of leaking, the leakage passages and the performance of the grouting curtains. An inverse modeling procedure combining the orthogonal design, finite element forward modeling of the transient seepage flow, artificial neural network and genetic algorithm was invoked to further evaluate the permeability of the foundation rocks whose permeability was underestimated in design, using the in-situ measurements of flow rate and piezometric head. The geological structures that lead to the leakage were identified and the seepage flow behaviors in the dam foundation and the left bank abutment were assessed. Given the connectivity nature of the sub-vertically oriented fractures that induce the leakage event, it is found that some of the drainage holes with relative larger amount of discharge could be closed or blocked for reducing the amount of leakage without remarkably increasing the pore water pressure in the foundation rocks.

Jan 1, 2015

By Dave Bulled

"This paper describes the design of a molybdenite flotation circuit using FLEET technology applied to kinetics data produced from laboratory flotation testing and distributed across the blocks of a mine plan using a geostatistical approach. The geostatistics assigned the statistical error that arises from having a limited amount of sample testing data to the kinetics estimates of each block of ore in the mine plan. The final design then included a quantification of risk based on the accuracy of the block flotation kinetics and model fitting. The design made reference to the extensive technical reports describing earlier metallurgical test work including some pilot plant work over thirty years ago.The testing involved conducting MinnovEX Flotation Tests (MFT) to determine the rougher flotation kinetics at the specified reagent conditions and rougher-cleaner tests to determine the change in kinetics resulting from regrind. These flotation kinetics were used within FLEET simulations to create a full-scale flowsheet and plant design including recommended equipment sizes and the forecast of operating results. Measurement of detailed flotation kinetics for a wide range of samples allowed the effect of size of grind and efficiency of classification (i.e. width of size distribution) to be predicted for the whole ore body.INTRODUCTIONAdanac Moly Corp. proposed to develop a 20,000 ton per day mill to produce high quality molybdenite concentrate from its Ruby Creek resource in north-western British Columbia. It is a relatively clean low grade porphyry-monzonite occurrence containing minimal quantities of other sulphides such as chalcopyrite, pyrite, sphalerite and galena. Molybdenite occurs mainly as coarse flakes with lesser amounts of finer sized values. An optimum plant design was required to can achieve the predicted operating results, at a known level of risk, while treating the variability inherent in the ore body."

Jan 1, 2007

By Erwin L. Zodrow

THE AUTHORS welcome this timely opportunity to comment o n a paper by MacLean and Merner (" Room-and- Pillar Mining at the Prince Mine of the Cape Breton Development Corporation " , ClM Bulletin , June 1978, pp. 59-62) concerning the rock falls and their relation to "a change in the strata". First, however, it is proper to express our gratitude to the Cape Breton Development Corporation, and in particular to A. R. MacLean, for making it possible for us at the College of Cape Breton to start two new collections. The first of these is a fossil plant reference collection from the Sydney Coalfield, Cape Breton (Upper Carboniferous period) , and the second is a documentation of the role o f pyrite in the formation of hydrated sulphates (samples from No. 26 Colliery, 1-B Mine, and the Prince Mine at Point Aconi). Conditions of sedimentation in the deltaic-type basin of the Upper Carboniferous time in the Point Aconi area were such that on the (coal) swamp, now represented by the Stubbart (or Hub) seam , (a) clays of varying thickness and extent were deposited , (b) biogenetic sulphur was introduced and (c) flora were buried. These are essentially the culprit s that make rock falls possible and at the same time predictable over large areas (in the present mine). The clays lithified to become shale, and biogenetic sulphur combined with iron to become pyrite (marcasite?), which exists as nodules and in fine-grained layers.

Jan 1, 1978

By A. Duerksen

"Surface coal mining in West Virginia has supplied energy to the eastern coast of the United States for over a century. Over the years, the coal mining industry has been forced to adapt as societal demands regarding health, safety, and environmental impacts have changed. More recent pressure has called for another iteration of change: long-term post-mining sustainability. The research discussed in this paper investigates one potential solution - or component of a solution - to improve the sustainability of surface coal mining in West Virginia: post-mining wind power. The paper begins with an introduction to the Appalachian region of the U.S. and the role that mining has played in its history, followed by a discussion of the need for sustainable mining and how post-mining wind power may help fulfill it. Data processing methodology of field data from monitoring locations is then explained. The results are then used to estimate the electrical output of a wind turbine. This data is then utilized in a case study discussion of one of the monitored sites. The paper concludes with an analysis of the broader implications of the research and a discussion of future work."

Jan 1, 2011

By G. Vouille, P. Bérest

Residual stresses observed in rocks often result from non-compatible initial strains. These stresses can be determined when the incompatibility tensor associated with the initial strain tensor is known. The residual stresses in a cylindrical rock sample can be computed the sample is considered small enough for its incompatibility tensor to be constant. Les contraintes résiduelles, dont on observe couramment les manifestations dans les roches, résultent souvent de l’existence de déformations initiales non-compatibles. Ces contraintes peuvent être calculées lorsque le tenseur d’incompatibilité associé aux déformations initiales est connu. Les contraintes résiduelles dans une éprouvette cylindrique sont données dans le cas où le tenseur d’incompatibilité est constant. Eigenspannungen, die man haeufig in Steinen beobachtet, sind oft Ergebnis einer inkompatiblen Deformation des Anfangszustandes. Diese Spannungen koennen berechnet werden, wenn der Inkompatibilitaets-Tensor der Anfangsdeformation bekannt ist. Die Eigenspannungen einer zylindrischen Probe werden fuer Fall eines konstanten Inkompatibilitaets-Tensor bestimmt.

Jan 1, 2003