Search Documents

By Albert Ruiz

The 2,250-MW, coal-fired Navajo Generating Station located in Page, AZ draws water from Lake Powell using submersible pumps installed in five inclined shafts. Drought threatens to lower the reservoir to below the existing intakes. A system of new steel-lined intake shafts located on the same site was required for uninterrupted plant operation. The small size of the site, and the need to keep the existing system in operation, required detailed designs and placed significant limitations on construction equipment and activities. The Navajo Sandstone that forms the near vertical shoreline of the reservoir is 98 percent very fine grained quartz, highly abrasive and contains highly fractured intervals that presented numerous challenges to drilling the new 152-m (500-ft) deep, 109-cm (43-in.) diameter intake shafts inclined 23° to 26° from vertical. Spatial constraints, submersible pump design and operational criteria required that each shaft have a unique inclination and orientation and hit a small breakout target located 76 m (250 ft) under water. Sophisticated drilling equipment and techniques as well as state of the practice downhole survey technology and methods were used to make adjustments and maintain drilling accuracy with less than 1 percent deviation. Environmental requirements mandated water as the drilling fluid and grout was not allowed in to the lake under any circumstances. The shafts were videotaped and the breakout locations were examined using an underwater remotely operated vehicle (ROV) to verify shaft locations and rock conditions, and to guide placement of pneumatic packers to ensure grout did not transmit to the lake during the steel liner installation. In anticipation of the invasion of quagga mussels, the shaft design included an allowance for a chemical dosing system and a copper-rich alloy at the exposed portions of the steel liner.

Jan 1, 2011

The 115-year history of the Hall-Heroult process for production of aluminium has been characterised by a sustained technology-driven improvement in costs and productivity. In the past decade the industry has effectively transferred best practice into older technology with improvements through computer control of the process, and redesign of cell linings using computer modelling . Incremental development is now at the point where diminishing returns will apply for further technical improvement effort however, until the gap between technical limits and current best practice is addressed through major process redesign. The process remains a long way short of its technical limits in energy consumption, carbon anode consumption, cell life and product purity. Investment cost in new capacity is very high, supporting the retention of older and less efficient technology and hence limiting the application of best practice in environmental performance and occupational health exposure. The industry is a major emitter of greenhouse gases yet the process has the potential to release oxygen as the primary waste. All of the above issues will be addressed in the new century, but only through commitment to the necessary long-term research and development that is required to achieve a redesign of the process.

Jan 1, 2000

By Christopher Mark

The first International Conference on Ground Control in Mining opened with the topic of pillar design. Two classic papers were presented, one by Bieniwski and the other by Wilson. Unfortunately, the two methods were so radically different from each other that it was nearly impossible to reconcile them. Adding to the confusion were the many other pillar strength formulas (such as the Salamon-Munro, the Holland-Gaddy, and the Obert-Duvall, just to name a few) that were also available. Little wonder that discussions of pillar design in those days often ended with anguished cries of ?but which formula is the right one?? The past 25 years have seen substantial progress in the science of coal pillar design. Indeed, one testament to the improvement is the relative scarcity of papers on the topic at recent Conferences. Two factors have been largely responsible for the progress that has been made. The first has been the collection of large data bases of actual case histories of pillar performance in a variety of settings, from shallow room-and-pillar mines through deep cover longwalls. These have made possible the development of empirical design procedures that are closely linked to real world experience. The second important factor is the development of sophisticated computer models that can accurately simulate pillar behavior and roof/pillar/floor interactions. Together, these two lines of research have led to a new understanding of pillar mechanics that identifies three modes of pillar failure: ? Sudden, massive collapse, accompanied by airblast, for slender pillars (width/height<4) ? Squeezing, or slow, non-violent failure, for most room and pillar applications (4<w/h<10) ? Entry failure or bumps for deep cover and longwall applications (w/h>10) It is particularly satisfying that the insights gained from numerical models broadly support those obtained from the empirical studies. While far less controversial than in the past, pillar design problems continue to arise. One recent example is pillar design for highwall mining. NIOSH has just released a software package, called ARMPS-HWM, which employs a number of modern pillar design concepts. Since highwall mining web pillars are long and slender, the greatest danger is that of a sudden collapse. ARMPS-HWM suggests two possible prevention strategies, one which concentrates on the SF of the webs, and the other which creates a ?pressure arch? using properly sized barrier pillars. The paper will close with a discussion of some current needs in coal pillar design, including: ? Updating older empirical methods, such as ALPS, where changes in technology (new types of roof support, more demanding ventilation requirements, faster retreat rates) may have made some of the original case histories obsolete. ? Methods for determining site-specific coal strengths, focusing on bedding plane strength and other factors that may effect confinement, as input for both empirical and numerical design. ? Improved methods for evaluating coal pillar performance for environmental issues, such as surface subsidence and hydrologic impacts, which consider such factors as depth, w/h ratio, water immersion/drainage, and time dependent seam strength.

Jan 1, 2006

By D. Küster, G. Franken, P. Schütte, J. Vasters

The CTC (Certified Trading Chains) mineral certification system has been piloted in Rwanda since late 2008. CTC project implementation is jointly driven by the Federal Institute for Geosciences and Natural Resources (BGR) and the Rwanda Geology and Mines Authority (OGMR), in cooperation with other national stakeholders. Five Rwandan mineral producers participate in the CTC project with their flagship mining concessions. Based on independent third-party audits, CTC certifies supply chain due diligence measures of these companies engaged in the artisanal mining sector through on-the-ground assessments of mining conditions, transparency, as well as mineral origin and traceability. The CTC system thus allows responsible mineral producers and their clients to verifiably demonstrate supply chain due diligence and good governance in conflict-affected and high-risk areas.

Jan 1, 2011

By V. Grujic, M. Grujic, D. Salatic

"Two areas are involved in the research work of the comminution process (crushing and grinding). The first one involves the changes of the size class distribution values that are definded by the differential equations in the function of the ore property and working conditions. The second area involves the comminution of the different levels in order to optimize the working parameters and to decrease the operational costs in the grinding process.We have studied, in detail, the possibility of functioning the crusher at the maximal loading, over 4500 kN, ball mills with diameters larger than 5.0 m and semiautogenous mills with diameters larger than 10.0 m.Using the computers, we have achieved the maximal loading range of the crusher, over Fc ? 4500 kN in the crushing process. In the grinding process, using the adequate differential equations in the automation process, we have established the correlation between the pulp mass capacity in the mill, pulp dencity, ore fineness in the pulp and recirculating ore charge.With the appopriate text, equations and graphs, this paper shows the results of our several years research work in the laboratory and in the ore comminution plant of Majdanpek Copper Mine."

Jan 1, 2003

By Carol A. Pilon

"IntroductionRECENTLY, the Saskatchewan Research Council (Saskatoon ) marked the completion of one of its coal-related projects with the publication of the Bibliography and Index of Coal in Saskatchewan and Adjoining Provinces and States, hereafter referred to as the Bibliography and Index of Coal. Over a two-year time period, literature was surveyed and indexed and bibliographic data were compiled using a computer-assisted information retrieval system called FAMULUS. The final publication contains 1150 bibliographic references, which are cross-referenced by six indices.The project was initiated in September 1974, in support of Saskatchewan's Coal Resources Evaluation Program , an ongoing research program sponsored by the Department of Energy, Mines and Resources (Ottawa) and the Province of Saskatchewan. This program places emphasis on such areas of concern as the occurrence of deposits, chemical and physical properties, calculation of reserves and computer-assisted applications for the evaluation of lignite resources in the Province. Attention is also given to aspects of geophysical exploration, mining conditions and economics, by-products and the transporting of lignite. These are the subject areas .covered by the Bibliography and Index of Coal.The over -all objectives of the literature indexing project may be enumerated as follows: (1) to build a specialized resource library by surveying established public and specialized libraries, and commercial data bases; (2) to enter library data into the FAMULUS information retrieval system, to be used to generate bibliographies and indexes, and to retrieve information by the use of specified searching techniques; (3) to make this library data available to interested persons."

Jan 1, 1977

By Walter von der Linden

On April 14, 1975, Consolidation Coal Company began to operate a longwall face in their Shoemaker Mine using shield supports. This was the first time that shield supports were used in the United States (1) 1/. Shortly thereafter, Kaiser Steel Corporation started a shield longwall face at their York Canyon Mine (2). From October 1975 through May 1976, three more longwall faces were commissioned in mines located in south-western Pennsylvania and northern West Virginia. In June 1976, four installations had completed their first panel and two installations had completed the subsequent move to the second panel where coal production is now well under way. During this time (April 75 to June 76) the total number of shield support face operating months, including moving time, was 40 and the combined face advance was approx. 17, 000 feet (5200 m) with face lengths varying from 450 - 550 feet (137 - 168 m). While the shield support experience in the U.S. is still limited on the basis of time and mining parameters, the operating results of all faces have been very satisfactory. New record 24 hr production figures were set and - far more important - long term production figures could be sustained on an impressively high level even when taking face moving time into account. The purpose of this paper is to review the performance of shield type supports in the U.S. and to assess their value as longwall supports for U.S. underground mining conditions with regard to roof control, maintenance, operator convenience, safety and productivity.

Jan 1, 1976

By A. J. Macdonald

Gold deposits hosted by banded iron formation (BIF) in Ontario exhibit a marked association with localized zones of deformed and hydrothermally altered BI:F . Secondary sulphides and carbonates are conspicuous. Proposed carbonate-facies IF , or exhali tes, such as green carbonate in the Larder Lake camp and ankerite veins in the Porcupine Camp are structurally controlled, hydrothermally deposited zones of carbonate replacement and fissure filling. Gold precipitation from hyd r othermal fluids in strain-generated conduits may be due to (a) plating upon secondary sulphides, (b) pH change due to carbonatization of BIF or (c) destabilization of gold in solution due to sulphidation of BIF .

Jan 1, 1984

By Richard O. Kneisley

An empirical method, based on U. S. Bureau of Mines field studies in several Western U.S. coal mines, is presented for sizing gate road yield pillars. Discriminant analysis was used to generate functions separating successful from unsuccessful case studies. These functions relate the pillar width-height and extraction ratios and a pillar development factor to the Coal Mine Roof Rating System (CMRR), and are assumed to establish three criteria that other entry systems, under similar conditions, must satisfy. A program, Pillar Sizer, from user-provided inputs, generates a range of pillar sizes that meets the proposed criteria. Although the analysis is based on a sample consisting primarily of two-entry systems, the derived expressions generate pillar sizes closely agreeing with observed, two-entry and three-entry in situ pillars. It is concluded that the proposed approach should assist mine operators estimate entry system yield pillar dimensions.

Jan 1, 2010

By Don Thompson

Canada’s oil sands are a controversial topic and virtually every newsmaker and layperson seems to have an opinion about this 179 billion barrel resource. The oil sands represent 97 per cent of Canada’s remaining oil reserves, but misinterpretation and misrepresentation of the facts are threatening development of a resource that generates significant employment and tax revenue for Canadians. Join Don Thompson, president of the Oil Sands Developers Group, as he dispels the top ten myths about Canada’s oil sands and presents an alternative perspective on an industry that can play a critical role in North America’s economic recovery.

Jan 1, 2010

By G. M. Ritcey

The recovery of copper from low-grade solutions res ulting from dump leaching is well known, whereas the recovery from highly concentrated copper solutions has not been practiced. This paper discusses the use of Ashland Chemical's Kelex 100, a substituted quinoline, for the recovery of copper from solutions resulting from leaching copper-nickel concentrates. A flow sheet is described, and an economic comparison shows Kelex 100 to be superior to either the LIX 64N or LIX 70 reagents of General Mills for the recovery of copper.

Jan 1, 1973

By P. Burmeister, R. A. Errath, A. Sapin

Sag Mills are becoming bigger in size almost every year. Concentrator plants are also becoming larger with more SAG and Ball Mills units with Gearless Mill drives installed in one plant. In contradiction to this development, concentrator plants are being built in increasingly remote areas, where the power supply and network conditions are not necessarily covering the needs for the operation of such plants. This paper describes sources of harmonic distortions and possible approaches to solve this problem. It also illustrates the permissible tolerances in terms of commutation of power electronics, based on already realized installations. Furthermore it explains how, and with which measures, harmonic currents created by non-linear loads with SAG and Ball Mill drives can be handled, and how harmonic standards can be fulfilled accordingly. Finally, this paper gives an overview about the technical impact of a strong versus weak network, and the economic relationship between them.

Jan 1, 2001

By J. Kruttschnitt

This paper, describing milling practice at Mount Ira Minis, is one of a series covering milling methods and cost that is being published by the Bureau of Mines, United States Department of the Interior. The Mount Isa concentrator began operations in day 1931 by treating a mixture of oxidized and sulfide ores. Since March 1935 only sulfide ores have been milled; this change involved major alterations to the flow sheet. The maximum capacity on mixed oxide and sulfide ores was 2,650 tons per day; the present capacity is approximately 1,880 tons of sulfide ore per day. The installation of additional crushing, grinding, and flotation equipment when completed early in 1939 will increase the maximum capacity of the concentrator to 2,240 tons of sulfide ore daily.

Jan 1, 1939

By D. Norval, J. J. Dunkley

The process of atomisation is introduced and related to granulation. Some processes applicable to ferroalloys are discussed, along with their limitations and advantages. Examples of applications of atomisation to the processing of ferroalloys, including ferrosilicon and ferromanganese for use in the welding industry and as injectable additions to steel or cast iron are also presented. The economics of the process and the impact of process scale are discussed, along with criteria for process selection and system design.

Jan 1, 2004

Technologies are receiving a lot of &apos;press&apos; - and rightly so; as they are seen as the means for achieving quantum leaps in productivity and cost reductions. A point of concern for Caterpillar is that we do not believe there is enough understanding of the infrastructure needed to support some of the future technologies, as well there is not enough utilisation of the current systems.

Jan 1, 1997

By John Hoelle

Coal mines in southern West Virginia, south-western Virginia and eastern Kentucky have experienced coal bumps at least since 1933. Most of the bumps have occurred due to high cover, strong roof and floor strata and stress concentrations due to the mining sequence. A longwall mine in eastern Kentucky first experienced coal bumps on the tailgate side of the longwall face in 1989. The bumps continued until 1996. The bumps were the result of: Thick overburden up to 2200 feet Strong roof and floor (strata strengths up to 25,600 psi UCS and elasticity modulus up to 4,800,000 psi Previous over-mining in places Sandstone channels Not all characteristics occurred simultaneously. The bumps produced seismic events recorded up to 4.3 (Richter scale magnitude), and damaged pillars that were up to 147 by 152 feet in size.

Jan 1, 2008

By G. R. Strimbeck

Experimental work is report on the gasification of 90-percent through 200-mesh, strongly coking Sewickley-bed coal with oxygen and with steam in three temperature ranges, namely, 2,700° to 3,400° F., 1,600° to 2,000° F., and 230° to 250° F. Thirty-one runs have been made, during which 56,000 pounds of coal have been charged to the generator at feed rates of 200 to 450 pounds of coal per hour. The average results, not the optimum results, are given in the following tabulation:

Jan 1, 1950

By Murali M. Gadde

Perimeter mining is a special form of very productive partial extraction method practiced at some mines in the United States. In the Illinois Basin mines where all major coal seams have weak underclay in the immediate floor, experience shows that any long-term ground control issues will arise due to floor failures rather than instability of the coal pillar itself. While there is a significant amount of work done on floor stability associated with regular pillars, no work has been done so far on the stability of perimeter pillars. This paper reports the results of a comprehensive study that was conducted for the first time on floor stability during perimeter mining in the Illinois Basin mines. A special plate template, which mimicked a common perimeter pillar configuration was created to conduct in-situ bearing capacity tests at five mines in three states of the Basin. Additionally, because of the complex shape of pillars created in perimeter mining that defies any closed-form solution, floor bearing capacity was studied using three-dimensional nonlinear numerical modeling. Based on these in-situ and numerical studies, some guidelines are provided for perimeter pillar stability analysis.

Jan 1, 2009

By Aline Silva Magalhães

As elevadas taxas de encruamento nos estágios iniciais de deformação plástica observadas para os aços bifásicos constituem uma das principais características que os habilita para aplicação em componentes estruturais na indústria de automóveis. Neste trabalho foi analisada influência de tratamentos intercríticos com aquecimento em temperaturas diversas, seguido de resfriamento brusco, no comportamento em termos de encruamento de um aço bifásico, por meio de dois métodos distintos de determinação do expoente de encruamento. Observou-se que a elevação da temperatura intercrítica influenciou de modo a reduzir o valor do expoente de encruamento, dado que o aumento da temperatura reflete a elevação do percentual de martensita na microestrutura do aço. Além disso, para as diferentes abordagens aplicadas para o cálculo dos valores de n, verificou-se que por meio da técnica de linearização da curva tensão versus deformação foram obtidos valores superiores do expoente de encruamento quando comparada à abordagem utilizando o critério da estricção.

Aug 17, 2017

By Ping Yang, Tian-bin Li, Min-hui Wu

"The process of filtrate loss of low solid-phase drilling fluid at different content of polyanionic cellulose is investigated by the standard filtration test. The test results showed that when time of filtration is same, the filtrate volume decreases linearly with the increase of content of polyanionic cellulose. When content of polyanionic cellulose is same, the velocity of filter loss decreases nonlinearly with the increase of time and the velocity of filter loss will reach a stable value. The filtrate volume in 7 to 8 minutes can reach half of the total filtrate volume. At the same time, the velocity of filter loss of drilling fluid decreases nonlinearly with the increase of viscosity. When apparent viscosity is between 3.5~4.15 mPa.s, decrease speed of velocity of filter loss is quick. The results are helpful for characteristics evaluation of filtrate loss of drilling fluid and control of filtrate loss.IntroductionDuring the process of drilling, water of drilling fluid can leakage into stratum, the water can result in instability and collapse of borehole wall. At the same time, the original ratio of drilling fluid will change. The density of drilling fluid will increase, the performance of the drilling fluid will change. Controlling amount of filtration is important to drill successfully. The additives of controlling filtrate loss are mainly two types, particle materials and polymer materials. High-molecular polymer is a kind of high-molecular material, has the adsorption effect, high polymer protection, can improve the advantages of slurry viscosity (Xu,2004 and Dehghanpour,2001). Some scholars carried out some study on the polymer material fluid loss agent in recent years, these study mainly focused on CMC, HEC, MHEC, CMHEC, starch and its derivatives(Zhang,2005 and Chevron,2009).About PAC (polyanionic cellulose) as drilling mud additives, a few of scholars carried out some relevant work. Plank (1992) applied PAC into ordinary freshwater drilling fluid and analyzed temperature stability of freshwater drilling fluid. Bennion (2000) applied PAC into drilling fluid and analyzed effect of polyanionic cellulose on strata inhibitory. Huang (2011) analyzed effect of PAC on properties of the high-density water-based drilling fluid. Mahto (2004) applied PAC into fresh water and salt-water drilling fluid and analyzed effect of PAC on rheological properties of the drilling fluid. Wang (2008) applied PAC into alkaline drilling fluid to study various performance of drilling fluid. PAC is a renewable resource and has good application prospect (Ankara, 2005). So it is very important to understand the effect of PAC on filtration process of drilling fluid.The test was conducted by changing the content of the PAC in drilling fluid. The object of this paper is to understand effect of polyanionic cellulose on filtration process of the low solid-phase drilling fluid."

Jan 1, 2017