Search Documents

By Patrick J. Hannigan, Geir Veslegard, Frank Rausche, Rozbeh B. Moghaddam

A common type of deep foundation used in Norway to support bridge structures is the drilled pipe piles (piles) filled with concrete reinforcement after installation. The standard installation practice is the use of down-hole hammers. Complex geology and difficult subsoil conditions in Norway causes a high variability of soil and rock layers which in turn make for differences between actual subsurface conditions and those expected from geotechnical exploratory borings. This situation is strongly noted when the foundations are not fully socketed, and the rock layer is sloped. In this particular case, special testing procedures are required to assess the drilled pile base material and evaluate the rock-socket to ensure full contact between the foundation base and the rock surface. The local standard practice to verify the latter condition, consists of coring and visually evaluating the material recovered at the bottom of the drilled pile. This paper presents a case where the coring and visual inspection were not possible and alternatively the geological material encountered at the base of the deep foundations was evaluated using force-displacement measurements. Two 1016-mm (40in) diameter open-end drilled piles identified as P02-04 and P02-05 were tested and evaluated using in-situ force-displacement data prior to filling the piles with concrete. Test results showed an average displacement of 7mm (0.28in) corresponding to 35MPa (5.1ksi) stress level for P02-04, and 7.2mm (0.28in) corresponding to a stress level of 38MPa (5.5ksi). Based on testing results, both drilled piles were within the established material assessment criterion presented by the local authorities. INTRODUCTION This paper presents a case study in Norway where the material encountered at the base of an open- end drilled pipe pile (pile) was evaluated using force-displacement data. In the deep foundation industry in Norway, it is a common practice to install piles to support transportation structures. Once the piles reach the embedment elevation, and the pile base is assessed, these are filled with concrete. In projects where sloping rock is the supporting layer, and all nominal loads are supported by the pile base resistance, assessing the material encountered at the pile base to ensure full contact with the rock becomes critical. The local practice to make this assessment consists of the use of weighted tape, coring, or inspection cameras. However, similar to any other testing and evaluation methods, these come with their own limitations. The variability associated with the use of the weighted tape, accessibility for the coring equipment to complete a coring process, or the conditions at the foundation base such as murky water or thick drilling fluids could significantly impact the photo or video quality taken at the pile base. In such conditions, it is important to consider alternate testing methods to evaluate the material at the foundation base.

Jan 1, 2018

By K. C. Dean

Discarded automobiles represent the greatest single resource of reusable metals, plastics, and rubber in the United States. This report presents results of Bureau of Mines research, conducted from 1965 to 1983, on separating and recovering useful materials from the scrapped hulks, using old and new metallurgical techniques combined with standard scrapyard methods. The Bureau determined the materials composition of three composite cars designated as circa 1960, mid-1970's, and early 1980's, and used these cars to study smokeless incineration and hand-sorting techniques. In studies on treating rejects from automobile shredders, the Bureau designed a process that included air classification, water elutriation, magnetic separation, handpicking, and heavy-medium separation, and also investigated cryogenics and liquation. Complete recovery of cop-per and other metals was economically made by hand and tool dismantling, leaching, or selective melting of starters and generators. Techniques are also discussed for plastic recovery and waste tire treatment.

Jan 1, 1985

By C. Sun

The Leeville underground mine has been in operation since 2006 and currently produces 3,200 tons of ore per day with an average gold grade of 0.4 opt. The mine has a large horizontal extent of 2,500 feet by 500 feet and a vertical extent of 20 to 200 feet. High density of joints occurs within the host rock. Based on Rock Mass Rating and field observation, the Leeville ground conditions are characterized as poor to very poor. As such, heavy ground support is required for the mining operation in Leeville. Ore zones with a height in excess of 10 m (35 feet) are considered for longhole stoping. A typical stope measures 6.0 m (20 feet) wide, 30 to 55 m (100 to 180 feet, depending on the ground conditions) long and 10 to 30 m (35 to 100 feet, depending the thickness of ore body) high, yielding 10,000 to 20,000 tons when completed. Narrow ore zones, less than 10 m (35 feet), are mined using cut and fill. These drifts are 4.6 m (15 feet) wide by 4.6 m (15 feet) high. Based on the afore-mentioned poor ground condition, the establishment of a ground control monitoring system is key to operating both safely and successfully. The ground control monitoring system is composed of comprehensive instrument design and installation. Instruments include Multi-Point Borehole eXtensometers (MPBX) and Stretch Measurement to Assess Reinforcement Tension (SMART) cables. The monitoring system covers the mining zones and infrastructure openings. After about two year?s applications and measurements, useful data has been and continues to be collected to use in future stope and infrastructure structure design. The system provides the information making engineer and operation teams to do their job more confident and efficiency. Keywords: Ground control, Monitoring system, Long hole stope, Instrumentation.

Jan 1, 2009

By Edwin G. Sharp, Frank S. Gaunce, George M. Freeman, Denis J. Kemp, Eric Dulson, Paul Salmon, Ernest R. Hamilton, Carl E. Parden

"THE ECSTALL ZINC PLANT was built for the treatment of the Kidd Creek zinc sulphide concentrates. Construction proceeded throughout 1970-71, with operations beginning in April 1972. The two concentrate types treated differ principally in minor impurity and precious metal contents. Processing flexibility was required to allow efficient recovery of the by-products, especially cadmium, copper and silver. The conversion of the zinc sulphide concentrates to end products follows a sequence of operations that are common to most electrolytic zinc plants and typical of the ""Tainton- Jephson"" flowsheet.1. Roasting in air at an elevated temperature to convert the metal sulphides to soluble metal oxides (calcine) and sulphur dioxide. The sulphur dioxide is converted to sulphuric acid in a contad plant and shipped by train to market.2. Leaching of the calcine in spent electrolyte to effect extraction and recovery of zinc as zinc sulphate solution, leaving an insoluble residue.3. Purification of the clarified zinc sulphate solution by cementation with metallic zinc dust to remove impurities detrimental to the electro-deposition of zinc or detrimental to product purity. The solids from cementation are the starting materials for secondary metal recovery.4. Electrolysis of the purified zinc sulphate solution to reduce the zinc to the metallic state while coincidentally regenerating the sulphuric acid for recycle to the leaching step."

Jan 1, 1974

By A. D. Fowler, M. T. Anderson

A phenomenological model is presented that relates Pb-Zn mineralisation to proximal geopressure zones. Typically, geopressure zones (GPZ) consist of masses of undercompacted sediment encapsulated within impermeable shales and are characterised by high formation fluid pressures. Heat flow is perturbed in some GPZ on account of their insulating properties. Geothermal gradients as high as 150 degrees C/km have been observed over short distances in the sediments of the US coast of the Gulf of Mexico. Some modern geopressure zones are known to reach temperatures of 120-150 degrees C at depths of 2.5-3.5 km. It is demonstrated that the zones may act as proximal sources of hydrothermal fluids, thus explaining the high temperatures of mineralisation observed in the deposits, which are hosted in basins characterised by thick, rapidly deposited, shale-rich clastic sequences

Jan 1, 1991

By F N. Baez

This paper supplements a keynote address prepared for the MassMin 2016 conference on mass underground mining methods, including block, panel, inclined and sublevel caving. It advocates for a new cave mining paradigm that takes advantage of a number of new and disruptive technologies or innovations that have evolved over the last 15 years, some of which were initiated by major mining companies such as Codelco. The paper will address the challenges that the industry will be facing in the future as well as possible solutions. As background, the paper summarises the challenges that the industry has faced in the past and how such challenges were addressed. The author acknowledges that given his more than 30 years of experience with Codelco Chile (operations and corporate), aspects of his intelligent mining concept have no doubt been influenced and have matured during his invaluable time with Codelco also as the Head of Technology and Innovation. In the paper, he uses some of the innovations developed within Codelco and by the Chilean Government to illustrate the concept of ‘intelligent mining’.CITATION:Baez, F N, 2016. ‘Intelligent mining’ – the way of the future, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 3–8 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

Year of Election 1944 Walter Hull Aldridge, New York, N.Y 1955 Louis S Cates, New York, N.Y 1946 William Fraser (Lord Strathalmond), London, England 1917 Herbert Hoover, New York, N Y 1955 George M Humphrey, Cleveland, 0

Jan 1, 1959

By Zephaniah Varley, Dominic Parmantier, Paul Schmall, Richard Martin, Red Robinson

Sequential excavation of the Beacon Hill Station has been accomplished in highly complex and inter-layered sand, silt, and clay soils with multiple perched groundwater tables. Successful excavation has required the installation of a deep dewatering well system used to depressurize sand layers above and within the excavated tunnel faces. In addition, the presence of sand layers in the crown of the Platform Tunnels required jet grouting at depths of up to 49m (160-ft). This paper discusses the design intent, construction, and effectiveness of the dewatering system and the selective jet grouting of sand horizons and shaft break outs for the successful construction of the deepest SEM station excavation ever completed in the United States.

Jan 1, 2007

By David Conover

Technological advancements in electronic sensors and mine-wide monitoring systems have improved remote monitoring and analysis of underground mining information. The effective use of . these systems for ground control applications, however, remains a challenge facing the mining industry. The U.S. Department of Interior, Bureau of Mines is conducting research, utilizing real-time acquisition of rock mechanics data, to provide mine operators the means to rapidly identify and manage potentially hazardous ground conditions. The Bureau has installed a remote monitoring network in a Colorado coal mine to record Pressures from instruments installed in the roof and pi1lars of gateroads and from transducers on shield-legs along the face. The field data are being monitored at the Denver Research Center, 150 mi from the mine. A computer at the Center analyzes the field data and generates graphic displays, which permit detailed examination of mine-wide ground conditions in real-time. For the first time, Bureau researchers are able to perform real-time monitoring and analysis of rock mechanics data while mining is in progress. The data collection and display capabilities of the system were effectively used to identify and evaluate face stability problems at the mine.

Jan 1, 1990

Professor Skeats said: I wish at the ,outset to express my appreciation of the h0!-l0ur conferred on me by my election as President of this Institute for the ensuing year. The selection of a geologist for this position by a body of mining engineers andmetallurgists may be taken as an indication of the recognition that the subject is one which may play a useful part in the great metal industry. Among the records of primitive man the finding of implements of bronze and of iron indicated one of the important, advances made in human civilization, and shows that...

Jan 1, 1924

By M. Ide, K. Takemura, S. Taenaka, K. Shinzawa

"The laser characteristic is strongry dependent upon the stoichometry of forsterite (Mg2Si04) and YSO (Y2Si05) single crystals, because of change in the valency and occupied sites of doped Cr in the lattice so that mole ratios of Mg0/Si02 and Y203/Si02 in the above single crystals must be precisely analyzed. In this study ICP-AES was applied for analyzing the mole ratios. Emission intensities corresponding to Si and Mg or Si and Y were measured at the same time with internal standard method. Preparation of sample solutions, measurement conditions of ICP-AES and interferences by coexisting components were discussed, resulting in excellently precise detennination of stoichometry of the above single crystals.IntroductionIn conventional stoichiometric analysis of single crystals, the stoichiometry is detennined by analyzing each component separately with titrimetry and gravimetry techniques. On the other hand, by stoichiometric analyses using ICP-AES, emission intensities corresponding to components are measured at the same time with internal standard method. Consequently erros caused by variation of analytical condition are canceled out.Cr-doped Mg2Si04 and Y2Si05 syngle crystals are known as laser materials. The change of valency and occupied sites of doped Cr affect the characteristic of single crystal as aleser materials. The change of state of doped Cr.Stoichometric composition of Mg2Si04 is constructed by 2mole of MgO and 1mole of Si02, and Y2Si05 is constructed by 1mole of Y203 and 1mole of Si02. In this study, required analytical precision in component mole ratio is within an error of 0.0010 for Mg2Si04 (CV=0.05wt%), and within an error of 0.0030 for Y2Si05 (CV=0.05wt%) (Table I )."

Jan 1, 1998

Bioleaching Metals from Waste Printed Circuit Boards and the Shapes of Microorganisms

Sep 13, 2010

In response to increased aluminum demand, U.S. producers have begun reactivating primary aluminum capacity which was shutdown during the 1974-1975 recession. Reynolds Metals Company started up almost 80,000 tons per year of idled capacity at Listerhill, Alabama, and Jones Mills and Arkadelphia, Arkansas plants. Howmet Aluminum Corporation and Alumax announced that the operating rate at their jointly owned facility at Frederick, Maryland was being increased from 75 percent to 100 percent, equivalent to a 44,000 ton-per-year increase in output. Kaiser Aluminum and Chemical Corp. expected to restart one of the two idled potlines at its Mead, Washington facility in May raising its production rate by 27,000 tons per year. ANTHRACITE - The anthracite market for the larger sizes continues at a good level, and although the demand for industrial sizes has been weak, the current trend indicates an increased demand for industrial fines by the steel, auto, and other industries.

Jan 1, 1976

By Charles H. Rich

This Bureau of Mines report is an expansion and update of Information Circular 8719 and comprises maps and tables listing the name, location, and other pertinent data concerning certain fuel-related projects. The maps show the locations of the planned or proposed facilities. The tables include information on projects involving the proposed or planned development of fuel resources, as well as the development of storage, transportation, and conversion facilities. The report covers the 24 States west of the Mississippi River including Alaska and Hawaii. Of the 808 projects for which information is provided, 219 concern coal mines, 246 concern electric generating plants, and 115 concern uranium mines; Energy Supply and Environmental Coordination Act coal conversion notices are also included. Because of the dynamic nature of the energy industry, many uncertainties exist and some of the listed projects may never become realities. Also, no attempt has been made to determine the degree of certainty or viability of each project.

Jan 1, 1978

A numerical method for discriminating between replacement and sedimentary processes is applied to a folded stratiform sulphide occurrence. It is shown that numerical treatment of chemical analyses from a single diamond drill hole allowed a rapid assignment of the ore to the syngenetic sedimentary class and thereby enabled a revision of the evaluation program concerned with consequent reduction in costs.

Jan 1, 1973

By B. P. Watson

The Bushveld platinum group metal deposits are two distinct, shallow-dipping stratiform tabular orebodies which strike for many hundreds of kilometres. Mining is extensive, with depths ranging from close-to-surface to 2 300 m. The mining method is a variation of planar open stoping. Pillars are widely employed to support the open stopes. In the deeper levels, in-stope pillars are required to fail in a stable manner soon after being cut, and the residual pillar strength is used to stabilize the hanging wall. These pillars are commonly known as crush pillars. Little work has been done in the past to determine pillar peak and residual strengths, and pillars have been designed using experience and formulae developed for other hard-rock mines. This has led to over and undersize pillars with consequential loss of ore, pillar bursts and potential collapses. This paper describes a crush pillar design methodology, and provides design charts. Three mining environments were incorporated in the investigations, which included underground and laboratory measurements, analytical solutions, numerical model sand back analyses. The results of the study are suitable for the areas where the research was carried out, and may also be applied with caution in other similar environments.

Jan 1, 2010

By Wilton Johnson

Native asphalt was produced in 1982 by five companies in two States, Texas and Utah. Bituminous limestone, used primarily as a paving material for street and road repair, was produced by White Uvalde Mines and by Azrock Industries, Inc., Uvalde County, Tex. Historically, gilsonite, a solidified hydrocarbon found only in Utah and Colorado, had been mined by American Gilsonite Co. and by Ziegler Chemical and Mineral Corp. from properties near Bonanza, Uintah County, Utah. During 1982, Hydrocarbon Mining Co., a subsidiary of the Oberon Oil Co., entered into a joint venture with Miocene Resources Inc. of Novato, Calif, to form Hydrocarbon Resources Co. for the purpose of mining gilsonite about 50 miles south of Vernal, Uintah County, Utah. Under the agreement, Hydrocarbon Mining contributed gilsonite-bearing properties held by lease or sublease as well as mining equipment to the venture. The property contained leases totaling 760 acres with probable reserves of 268,000 tons of gilsonite. Miocene Resources provided the partnership with a minimum of $200,000 to develop two of the leases and were to be responsible for management of the mining operations.2

Jan 1, 1983

By Jim Richards, Eli Choueiry, Brett Robinson, Amanda Elioff

The Los Angeles Metro Gold Line Eastside Extension (MGLEE) extends Metro’s light rail system to the densely populated and growing East Los Angeles communities. Much of the 6 mile alignment consists of at-grade track, but the project also features a1.7 mile underground segment in cut-and-cover and twin-bored tunnel structures. In light of past experiences with open shield construction, The Metropolitan Transportation Authority (Metro) specified, for the first time, use of Pressure Face Tunnel Boring Machines (TBM’s) to advance tunnels through soft ground. This paper describes the history of the tunnel design, construction management, and construction methods adopted that resulted in successfully completing the tunneling segment.

Jan 1, 2007

By H. Robert Ensminger

The Belizean economy registered a modest real growth of 1.3% during 1981. The gross domestic product (GDP), based on current prim was $121 million' with an inflation-rate of 10%. The country received $19 million in economic aid during 1981. In early 1981, Belize'e four commercial banks raised the interest on deposits to 15% in an effort to curb capital outflow. During 1981, the financial situation deteriorated somewhat, particularly the balance of payments. For the year the total value of imports exceeded exports by almost $38 million, while the Government continued to maintain a fairly free trade policy. Import duties and term averaged about 8% on essential item and 40% on nonessential ones.

Jan 1, 1983

By Gloria Fernández

La contaminación por drenaje ácido de mina se considera como la responsabilidad ambiental y económica más grande que actualmente enfrenta la industria minera. En ese sentido, se delimita las áreas afectadas mediante la perforación de pozos de monitoreo a través de un estudio geofísico previo. Por ello, el presente trabajo señala los métodos geofísicos como herramientas que pueden ayudar a delimitar y mapear las zonas afectadas por la contaminación proveniente de drenaje y filtraciones que va desde canchas de relave, pilas de lixiviación a minas abandonadas, etc.

Aug 25, 2002