Search Documents

By Edward E. Johnson

The principal purpose of this study was the development of an engineering and economic model of a hypothetical large-scale open pit gold mining operation. The guiding concept in developing the model was the idea that, through study of a number of such models, it would be possible to evaluate a mineral property and to make reasonable estimates of the benefits to be derived from research in mining and metallurgy. The model by use of a computer is able to produce results easily and quickly when cost factors are varied. Cost factors may be varied as a result of assumptions of improved technology or of assumptions of assuming different approaches or methods to accomplish a particular segment of the mining or processing operation. The discounted cash flow rate of return was used to measure the effect of changes in costs or expected revenue. In this study, assumptions based on past processing practices were made in an effort to reduce costs of processing the ore These assumptions were: (1) Eliminating the low-grade cyanide circuit; (2) reducing the quantity of material to be processed by screening after crushing; and (3) using a combination of assumptions (1) and (2). All three assumptions resulted in reduced capital investment and operating cost that caused substantial increases in the rate of return.

Jan 1, 1968

By Stephen Tadolini

A unique circumstance created by monitoring a pre-driven longwall recovery room permitted measuring the stresses of a coal pillar throughout its entire life cycle in less than a week. A fender pillar, created in approximately the middle of a longwall panel at a depth of 650 ft, transformed from a solid barrier pillar - to a yielding pillar - to a residual pillar as 3 ft slices were methodically removed with the longwall shearer. The complete transformation, or life cycle, took place in less than 12 hours. The stresses were quickly transferred from the pillar onto the standing pumpable concrete supports and into the outby pillars. Roof to floor closure measurements, combined with the timing of the pillar behavior, provides a detailed look at the uncontrollable convergence of underground mine openings. Pillars remain the most important form of ?primary support? and understanding these life cycles is vital for safe and efficient mine design, in both room and pillar and longwall panel extractions.

Jan 1, 2007

By Mark C. Russell, Charles T. Russell, Brooke Colburn, Parker Bailey, Desiree Bernhard, Kaito Durkee, Tristen Cutshall, Rob P. H. Urselmann

Hypersonic tunnel boring (HTB) uses directed, high velocity projectile impacts to remove rock. HTB is highly independent of rock strength and targets hard, abrasive rock and variable rock environments. This paper discusses history, theory and presents test (2×2 m and .75×.5 m tunnels) field trial results and technical and economic evaluation. The HTB tests are compared against the historic ‘project REAM’ and the concept against tunnel boring machines and drill & blast in design studies for full-scale 12 m and 4.5×5.5 m tunnels. The positive results indicate that under these conditions HTB can replace Drill & Blast and Tunnel Boring Machines.

Jun 13, 2021

By A. W. Hall

Cylindrical plastic scintillators were investigated for efficiency in detecting neutron-induced prompt gamma rays. Scintillator performance was compared on the basis of half-resolution and peak-to-trough ratios for gamma spectra obtained from Co-60 (1.17 and 1.33 MeV), Th-228 (2.62 MeV), and PuBe (4.43 MeV). Various sizes of Pilot Chemical scintillators (types B, F, M, and Y) were tested. The best half-resolution, 7.7 percent for PuBe, was achieved with a 5-by 5-inch Pilot Y?scintillator and dual photomultipliers. Comparison with sodium iodide (NaI) scintillators and the use of plastic scintillators for on-stream analysis of sulfur in coal is discussed. Plastics were found to be unsuitable for on-stream analysis of materials having complex prompt gamma ray spectra; however, they could conceivably be used for those yielding Simpler spectra.

Jan 1, 1974

By William F. Jahn

Because of the' situation in Europe during the summer of 1939, with the possibility of war and consequent curtailment or loss of supplies of tin to the United States, the Bureau of Mines undertook an investigation of domestic tin resources. This was permitted by the Strategic Minerals Act of 1939, which authorized investigation of possible domestic resources of strategic minerals necessary in a national emergency. The minerals selected were in short supply, and the United States depended almost entirely on imports to meet normal requirements. The Black Hills of South Dakota were selected for investigation as one possible source of tin because of the occurrence of the mineral there has been known since 1876, although production had never been important. The Tinton area, in the northern part of the Hills, had received the most attention and contained some minor indicated and inferred tin deposits.

Jan 1, 1949

By Michelle Stokes, Alexandra Miller, Campbell McKenzie

"The ancestral Ringarooma River in northeast Tasmania has transported alluvial tin and other heavy minerals from their onshore source of stanniferous Devonian granites downstream into what is now Ringarooma Bay. Previous exploration work has demonstrated the presence of potentially economic tin mineralisation within the palaeochannels and terraces associated with the submerged river.The offshore tin resource lies directly on the seabed or with less than 2 m of overburden, and within 5 - 50 m water depths in the wider bay area. The main river channel continues offshore for at least 13 km, with high tin grades found within the palaeochannel but also dispersed across the sea floor as a sheet wash, a result of Quaternary sea level change reworking the placer deposits. This drowned portion of the coastal plain contains a continuation of rich tin leads as low gradient anastomosing channels, and has been delineated by marine seismic and drilling activity since the 1960s. Tin grades in the Tertiary and Quaternary alluvial profiles vary from 50 - 300 g/m3, with the highest concentrations in the coarser basal horizons. A previous offshore explorer estimated a resource of 194 Mm3 at 150 - 250 g/m3.Kenex Ltd created 3D models of the paleochannels and the mineralisation with the aim of better constraining the resource estimate and identifying additional depositional areas. The modelling was undertaken with the input of geophysical data, bathymetry and geochemical sampling of the seabed surface and from historic offshore drill holes. A prospectivity model covering Ringarooma Bay was produced to target tin-bearing gravels. Predictive maps were created to represent various features of the offshore mineral system, including assessing gradient changes in palaeochannels and their sinuosity. The model identifies areas with higher potential for alluvial tin mineralisation and will be used to focus the exploration programme over tenements currently held by Kenex Ltd."

Sep 1, 2014

By Patrick Wong, Gareth Hatch, M. A. Halim, V. I. Lakshmanan, Darcy Tait

"This paper describes development of an integrated chloride process for separation and purification of REEs. The process includes atmospheric leaching of ore/concentrate with mixed chloride lixiviant containing HCl and MgCl2 followed by bulk recovery of REEs, dissolution of the bulk intermediate product, and separation of individual REEs by solvent extraction (SX) process steps. Mixed chloride leaching technology provides the opportunity to regenerate the lixiviant, while the addition of MgCl2 in HCl enhances the hydrogen ion activity by orders of magnitude increasing REE extraction efficiency at a lower concentration of HCl. An individual REE separation process developed by Innovation Metals Corp. is being piloted at a state-of-the-art facility at Process Research ORTECH Inc. in Mississauga, Ontario, Canada. The SX process includes the separation of light REEs (La – Nd), medium REEs (Sm – Gd) and heavy REEs (Tb – Lu plus Y) from leach liquor followed by individual REE separation. Each SX circuit proceeds by multistage extraction followed by scrubbing and stripping. The process is chloride based and reagents are recycled, reducing waste generation and optimizing water usage to reduce environmental impact.INTRODUCTIONRare earth elements (La to Lu plus Y) exhibit a range of unique magnetic, electronic, catalytic and optical properties. Due to these special properties, the application of REEs is increasing and they are found in components for wind power generation, hybrid electric cars, catalytic converters, and many electronic devices.Rare earth elements (REEs) are commonly divided in two groups: light rare earth elements (LREEs) and heavy rare earth elements (HREEs). Light rare earth elements include elements from lanthanum (La) to neodymium (Nd). Although promethium (Pm) is considered an LREE it is unstable and scarcely occurs in nature and is generally excluded. Heavy rare earth elements include elements from samarium (Sm) to lutetium (Lu) plus yttrium. Although rare earth elements are not rare and the rare earth oxides are scattered around the globe, over 95% of REEs+Y are currently produced in China (Pitts, 2011). On one hand the Chinese government is restricting the export of rare earth elements and on the other hand the demand for REEs+Y is increasing in the rest of the world. This has created an imbalance in the supply and demand of rare earth elements and has led to a rush for developing new rare earth projects."

Jan 1, 2016

By M. N. Rubin

This report summarizes the work performed under USBM contract J0100018. The purpose of this work was to document the currently available noise control techniques that can be incorporated into new coal preparation plants during the design stage. This was accomplished by reviewing the related experience of the contractor and subcontractor (Bolt Beranek and Newman Inc.), conducting an extensive literature search, visiting operating coal preparation plants, and contacting various equipment manufacturers. The treatments addressed include equipment substitution, changes in plant layout, and retrofit treatments for existing equipment.

Jan 1, 1982

By A. G. Starliper

The report covers studies by the Bureau of Mines on the removal of metallic values in two waste products from the Longhorn tin smelter at Texas City, Tex. One product was a slag that contained tin, tungsten, iron, tantalum, and columbium. The other product was a spent acid solution that contained tin, tungsten, iron, lead, copper, zinc, and silver and that came from presmelting treatment of impure tin concentrates. Molten slag was treated with sulfur or sulfur compounds and with coke, calcium carbide, or gaseous reductants to form tin sulfide that volatilized from the charge and to reduce tungsten along with iron and silicon to form a carbon-bearing metallic layer. The metallic layer was treated by an oxidizing alkali roast and then was water-leached to extract the tungsten. The waste acid was used in other experiments to dissolve an iron-tin- tungsten alloy (hardhead) obtained by direct reduction of the slag. An insoluble fraction containing tungsten, silver, silicon, columbium, and tantalum was removed, and copper was cemented on metallic iron, Tin was recovered by cementation on zinc plates, and lead was precipitated by adding sulfate ion. Iron was precipitated by increasing the pH which left a solution containing principally zinc. Slabs of hardhead were electrolyzed in an electrolyte consisting of waste acid to plate out groups of metals at different pH?s. The time did not permit thorough exploration of this method of treatment.

Jan 1, 1962

By Sidney Katell

This report is the fourth in the series, Bibliography of Investment and Operating Costs for Chemical and Petroleum Plants. The initial work, Bureau of Mines In- formation Circular 7516, was published in October 1949 in conjunction with the synthetic liquid fuels program authorized by Public Law 290, 78th Congress. It included references to and abstracts of publications appearing from 1930 to September 1948 on all processes in general use in the petroleum refining and chemical industries. A supplemental bibliography, Bureau of Mines Information Circular 7705, was published in January 1955 to cover the period September 1948 through June 1952; and Supplement 2, Information Circular 7751, published in September 1956, covered the period June 1952 through June 1954. The present supplement covers the period July 1954 through December 1956.21 The information in this paper was obtained from the following sources: 1. Bureau of Mines Information Circulars. 2. Bureau of Mines Reports of Investigations. 3. Chemical Engineering. 4. Chemical Engineering Progress. 5. Chemical Engineering Costs Quarterly (Cost Engineering).

Jan 1, 1958

By T. F. Mitchell, J. A. McAllister, S. J. Hussey

"INTRODUCTION During the Bureau's extensive program of investigating possible domestic sources of manganese, an are-dressing study was conducted in its laboratories at Salt Lake City, Utah, on a sample of oxide manganese ore representative of vein material from the Ophir Hill mine at Ophir, Tooele County, Utah. The sample (obtained by blasting down and mixing a portion of the vein) was submitted by the Ophir Development Co. of Ophir, Utah. As the ore was too law in grade to be acceptable for direct production of ferromanganese, it was tested to determine its amenability to concentration by ore-dressing methods.At the beginning of the investigation of manganese-ore beneficiation in December 1940, the only product marketable to Metals Reserve Company was ferrograde manganese, grade B, the requirements for which follow: Mn, min., 48 percent; Fe, max., 7 percent; Si02, max., 10 percent; P, max., 0.18 percent; A1203, max., 6 percent; Zn, max., 1 percent.Later, the specifications were modified gradually. As of May 15, 1943, manganese products were acceptable if they contained over 35 percent manganese and less than 3 percent zinc and 1 percent phosphorus. Prices were based upon material containing 48 percent manganese, 6.0 percent iron, and 11 percent silica plus alumina. Premium were paid for manganese content in excess of, 48 percent and iron content below 6 percent, penalties being imposed upon products containing less than 48 percent manganese or more than 6 percent iron or more than 11 percent silica plus alumina. The specifications for commercial manganese further required that maximum particle size be 12 inches and that 75 percent of the product be coarser than 20-mesh. Therefore, fine material, such as table and flotation concentrates, had to be nodulized or sintered. In addition, carbonate manganese ores were not acceptable unless calcined."

Oct 1, 1947

By Sam S. Taylor

In most oil fields, natural gas is the major source of energy causing flow of oil to the well. The amount of gas produced with the oil generally exceeds actual energy requirements, so that in time the gas reserve of the field becomes seriously depleted and the oil production must be stimulated by some auxiliary means. One of these is to repressure the oil formation with natural gas; or, where a as supply is not available, often air is used. Although air is a cheap and convenient repressuring medium, its use sometimes is attended with several disadvantages. First, the return air-gas mixture decreases rapidly in fuel value, often until it can be used no longer as a source of power. At the same time, explosive mixtures may result if recycling is used, causing hazards to life and equipment. Second, sortie fields experience considerable trouble with the formation of emulsions which become increasingly difficult to treat. Although there is no definite proof that air repressuring always causes these emulsions, many operators are convinced that this is the case. The Petroleum Experiment Station of the United States Bureau of Mines at Bartlesville, Okla., has been interested in problems connected with air-repressuring for a number of years. Some time was spent in studying the so-called "bad gas"--return mixture of low fuel value. However, it appeared impossible to attack the problem successfully from this angle, and an approach was made through a laboratory-scale study of direct oxidation of crude oil.

Jan 1, 1934

By Kurt F. Weitz

"The number of materials that can be classified as fillers covers an extremely wide range: this paper outlines those fillers of the industrial mineral type that find extensive application in the paint and plastics industriesIn the paint industry, mineral fillers are known as extender pigments. Extenders are added to paint and plastic compositions to (1) lower the cost and (2) rein-force or modify the physical properties of a composition.Commonly used extenders are classified according to chemical type and discussed in terms of the change in physical properties that they impart to a paint or plastic film. Available cost reductions and data on the consumption of extenders in the Canadian paint industry are also included."

Jan 1, 1970

By B. F. Haanel

IN the fall of 1929, a paper was presented at the Annual Western Meeting of the Institute entitled The Fuel Research Laboratories at Ottawa and the Scope of Their Investigations. At that time, the equipment of the laboratories had not been completely installed, but the regular routine work was being carried on as usual, and several large-scale investigations were being conducted. It is now five years since that paper was presented, and it seems fitting that a brief description of the investigations which have been undertaken, together with results-especially those which have reference to western Canadian fuels-be presented at this Annual Western Meeting. The coal mining industry of western Canada has, within the past few years, suffered many unfortunate vicissitudes. The replacement of coals by oil, for bunkering ships, for operating railway locomotives, and for heating, has weighed heavily on the coal mining industry of British Columbia and Alberta generally, but more particularly in the Crowsnest Pass area and Vancouver-and hydro-electric developments have also left their impress. With a full appreciation of these conditions, the Department of Mines planned research and large-scale investigations which it was considered would be of the greatest benefit to the coal industry, and the results have amply justified the plans and anticipations. The fact, however, must not be lost sight of, that the application of the findings of certain of these investigations would not have been feasible had not the Federal Government assisted the transportation of coal by the application of railway subventions. These subventions permitted Canadian coals to compete at competitive points with United States coals, and it must be admitted also in this connection that certain of the collieries which have benefitted, both as a result of the railway subventions and the investigations conducted by the Fuel Research Laboratories of the Department of Mines, made special efforts to produce a coal which was capable of competing with the American product, by special preparation at the mines.

Jan 1, 1936

By John D. Godfrey

A brief account of economic developments in and around northeastern Alberta is presented and mention is made of mining and industrial developments currently of interest in the area. Planned and projected operations are briefly discussed for this region. The history of geological surveys and mining activities in the Shield area of Alberta and the adjoining parts of Northwest Territories and Saskatchewan is traced. Reassessment of the presently-known economic picture of northwestern Canada in conjunction with some recent information on Precambrian structures of northeastern Alberta points to some interesting mining possibilities, particularly in and around that province.

Jan 1, 1960

By Clarence O. Babcock

In this report, the Bureau of Mines presents a method for reducing the complexity of designing room-and-pillar mining systems by treating them as anisotropic soft inclusions in the surrounding ore or host rock. Theoretical models were derived for the calculation of the effective Young's moduli for these systems. The predicted behavior of the plate-type elements used in these models agreed well with test results from 21 plates each with 49 holes spaced on a 7 X 7 Cartesian grid. The plates behaved as anisotropic solids, the effective Young's moduli of which could be predicted from the scaled hole size and spacing. Actual hole shape was insignificant. The effective Young's moduli for simple mining systems are calculated in sample problems. This approach should provide information about field stress in the mining region and the stress distribution in the surrounding ore or host rock when the actual mining configuration is replaced by an anisotropic inclusion in a finite element analysis. The field stress within the inclusion can then be applied to the actual opening shape to determine the stress distribution within the mining region.

Jan 1, 1970

By B. A. Rogers

IN addition to the usual methods of manufacturing steel, a number of special processes have been the subject of considerable experimentation-and use in manufacturing practice. A number of these methods have been of a type in which a rapid refining action has been secured through the intimate mixture of fluid slag with fluid metal. The persistence with which more rapid methods are sought is indicated by the current interest in the Aston' method for producing wrought iron and in the Perrin2 process for dephosphorizing and deoxidizing steel. In the Perrin process, in particular, the mixing action is extremely vigorous and the reactions proceed with surprising speed.

Jan 1, 1936

By Alexander May

This report describes a new method of weighing based upon observing the apparent weight of an object ill two separate pure gases. The method is presented in terms of experimental data which prove its soundness, but does not attempt to show the maximum accuracy possible with this technique. The new method incorporates the underlying principle that the apparent weight of an object is a linear function of the density of the atmosphere in which the object is weighed. The coefficients of this linear function are the true mass and volume of the object. From this functional relationship the true mass and volume of the object may be determined.

Jan 1, 1970

By Stephen Utter

Stresses induced by block-caving mining were estimated from in-place measurements of strain or deformation in rock and concrete around mine openings. The four types of gages used for measurements in the Climax Molybdenum mine during 1959-61 were Whittemore gage, Carlson strain meter,2 Valore strain cell, and Climax extensometer. Gage performance in the laboratory was evaluated by stressing instrumented rock and concrete specimens in a universal testing machine and by comparing measurements taken by the gages and a standard gage. Gage performance in the mine was evaluated by comparing measurements taken during an 18-month test. The Whittemore gage, Carlson strain meter, and the Climax extensometer proved suitable for the investigation; the Valore strain cell, effective in the laboratory tests, gave erratic measurements in the mine.

Jan 1, 1965

By M. Pelegrin Rodríguez, J. Castellanos Suarez, R. Causse Miyares, A. Mosqueda Martínez, Rubén Aja

"This paper will describe the methods and the results of studies to integrate polymetallic nodule extractive metallurgy methods into existing and operating technologies or plants with the aim of reducing the capital cost of deep-sea mining challenges and to streamline the supply chain of raw materials where such opportunities exist (Moa Bay and others). It will also assess the possibility to carry out pre-industrial processing operations with productivity corresponding to pilot mining operation in the Clarion Clipperton Fracture Zone (5–10% of assumed annual production) with the use of existing facilities. The present study shows the results of high pressure acid leaching of polymetallic nodules (PN) mixed with laterite non-commercial ore. It also presents PN processing in the presence of ammoniacal tailings obtained from the Caron process. The experiments were carried out according to 24 full factorial design. The regression equations were determined for extractions of Ni, Co, Cu, Zn, Fe and Mn. The obtained results show that increasing temperature, the acid/ mineral ratio and the leaching time have a positive and significant effect on extraction of all the studied metals. However, increasing the tailings addition favors the extraction of the Co, Zn and Mn. The extraction of Fe diminishes, while the extraction of Ni is not affected. In the following conditions; 180 min, 260°C, 0.5 kg acid /kg minerals and 2.5 kg PN/kg tailing; the following extractions were achieved; 96% Ni, 90% Co, 97% Cu, 99.9% Zn, 43% Mn and 26% Fe."

Jan 1, 2017