Search Documents

By Musa Karakus

Reflected light microscopic (RLM) examination of dust particles from lead and copper smelters can effectively characterize their mineralogy, texture, and origin. Scanning electron microscopic-energy dispersive spectroscopic (SEM-EDS) analysis provides confirmation of the optical identifications and chemical data on the phases. Studied lead smelter dust samples were from the: I) blast furnace, 2) sinter plant scrubber, 3) sinter plant crusher, 4) dross furnace, and 5) refinery. Phases identified included galena fragments, melted PbS, metallic Pb and Cu, Cu-Ni, Cu-Zn, Zn-Ag, Zn-Cu-Ag, Ni-Cu-Sb, and Ni-Cu-Zn-Ag metal alloys, Ni-sulfide, Cu-sulfide, and Cu-Pb-sulfide dross .phases; slag and sinter particles, coke fragments, unreacted original feed phases: pyrite, chalcopyrite, sphalerite, siegenite, bravoite; and oxidized particles: iss, bornite, chalcocite, covellite, magnetite, hematite, and goethite. Dust from a secondary copper refinery were found by RLM and SEM to consist of tenorite, cuprite, cassiterite, two silicate phases. Magnetite, hematite, Fe-Al-Cr-Mg spinel, periclase, forsterite, and wollastonite were derived from the furnace linings during initial cleaning.

Jan 1, 1992

By Marietta Canty

A paper is presented in which an innovative biological process is described for the treatment of cyanide-, metals-, and nitrate-contaminated mine process water. The technology was tested for its ability to detoxify cyanide and nitrate and immobilize metals in wastewater from agitation cyanide leaching. A pilot-scale demonstration is described in which a pilot plant was constructed to demonstrate the technology on a mine process waste stream at a mine in Nevada. The demonstration was performed Jointly under the Mine Waste Technology Program (MWTP), which is funded by the U.S. Environmental Protection Agency (EPA) and is jointly administered by the U.S. Department of Energy's (DOE) Western Environmental Technology Office (WETO) and the Superfund Innovative Technology Evaluation (SITE) Demonstration Program under Interagency Agreement Number DW89938513-0 I-0. MSE Technology Applications, Inc. (MSE) located in Butte. Montana, was the contractor responsible for conducting the project, and Pintail Systems, Inc., of Aurora. Colorado, was the technology provider. The pilot-scale unit was field-tested at the Echo Bay McCoy/Cove Mine southwest of Battle Mountain, Nevada. The biotreatment process was considered to be successful in destroying cyanide in the mine process water. The process was also determined to be effective in removing metals. The pH was consistently neutralized, and nitrates were successfully removed from the mine process water. As a result of conducting these pilot-scale tests, the biotreatment process was concluded to be an innovative, cost-effective alternative for the treatment of mining wastewaters.

Jan 1, 1998

By Lucas de A. Pontes, Lázaro A. Rohen, F. V. Carlos Maurício, Janaina da Silva Vieira, Sergio Monteiro, Dhyemila de P. Mantovani, Frederico M. Margem, Anna C. C. Neves

The lower density of the lignocellulosic fibers such as the hemp fibers and the other natural ones is one of the characteristics that allow the scientists to obtain high levels of specific properties that when compared to the properties of ordinary reinforcements gives to the hemp fibers an advantage as a material with an expressive potential in the mechanical properties area. Then, the aim of this present work is to characterize the relative density of the hemp fiber related to the water using the pycnometry technique. This technique uses the pycnometer and it is divided in two steps. In the first step the correction factor and the moisture content of the fresh hemp fiber specimen and in the other step some weightings were done such as the dry specimen (g), empty pycnometer (g), pycnometer + water (g) and pycnometer + water + specimen (g) using a digital balance with a precision scale of 0.001 g of the bran INNERSCAN. Based on these measurement and calculations using some formulations already established in previous studies, the relative density of the hemp fiber found was around 1.393 g/cm3 and the moisture content around 7.1%.

Mar 1, 2017

By Truan-Sheng Lui, Li-Hui Chen, Fei-Yi Hung, Cheng-Yi Chen

"This research used the austempering heat treatment on the SCM435 thin specimen with a type of double loop and obtained the Cr-Mo bainite structure, and then we could further investigate the mechanical properties of SCM435 bainite structure. Experimental data showed the stability of the mechanical properties of specimen with austempering temperature 830°C for 25 minutes was better than that of 15 minutes. The size of austenite grain affected the strength of thin specimen. After austempering at 830°C-25minutes and salt bath at 290°C, the stability of UTS was better than that of salt bath at 310°C and 330°C. The average hardness of all specimens was about more than HRA70. The specimen with austempering at 830°C-25minutes and salt bath at 290°C-30minutes had bigger grain size of austenite and retained y, it also had higher hardness and strength toughness. So, its stability was improved for tensile strength comparing with traditional tempered martensite process.IntroductionSCM435 is a Cr-Mo steel with high strength and high hardness properties, and it has been widely used in machine parts, shafts, gears and strength screw products [1-3]. However, this system often has lower reliability due to the brittleness of high-temperature tempering and quenching inequality. Considering the austempering heat treatment can obtain the uniform bainite structure to improve the temper brittleness, and the austempering heat treatment is a continuous process that it also has efficiency and uniformity. For the thin plate specimens, the mechanical properties of the bainite structure are better than traditional martempering structures."

Jan 1, 2013

By Charles H. Bucknam

A gold sampling optimization study was carried out in support of open pit gold mining operations for the Newmont Gold Company Bootstrap-Capstone deposits in Northeastern Nevada. Six bulk samples were tested using fire refining techniques at field particle size, to determine coarse particle heterogeneity of the ores, and by gravity .concentration methods at 10 mesh particle size, to observe any particulate gold liberation. An overall sampling model is presented for the deposit based on the pooled test information, to reconcile the results of coarse particle heterogeneity testing and the fine particle 'liberation testing. The sampling model is used to recommend procedures to control the variability of gold grade estimation due to the fundamental error (nugget effect) during sampling, sample preparation and assaying of the ores and other fundamental variances. The technique of simplified quantitative risk analysis (SQRA) is used to provide an economic justification for implementation of. recommended improvements to field sampling practices.

Jan 1, 1999

By David R. Jessey

An ore microscopic and geochemical study of the nickel-cobalt occurrence in the Southeast Missouri Mining District has revealed several significant relationships. Siegenite [(Ni,Co)3S4] is the dominant nickel-cobalt sulfide in the ores, however, several other members of the thiospi¬nel group (AB2S4) occur: carrollite (CuCo2S4), nickelean carrollite [(Co,Ni,Cu)3S4], fletcherite [Cu(Ni,Co)2S4] and polydymite (Ni 3S4). In addition, bravoite [(Ni,Fe)S2], vaesite (NiS2), millerite (NiS) and gersdorffite (NiAsS) are present. Thiospinel composition varies dramatically within the district. Paragenetic studies have shown that the stratigraphically lowest thiospinels are the most cobalt-copper-rich. A detailed ore microscopic study of the AMAX Lead Company Buick mine has also shown significant changes in mineralogical association, texture and grain size of the siegenite along the north-south strike of the major ore bodies. Siegenite commonly replaces and veins chalcopyrite and is subsequently replaced by sphalerite. Less commonly, siegenite and chalcopyrite are observed to form linear replacements along sphalerite grain boundaries. The grain size of the siegenite varies markedly, but in a predictable north-south pattern that is consistent with a genetic model formulated from geo-chemical data. The compositional as well as textural trends displayed by the thiospinel mineralization could be exploited to optimize recovery of any or all thiospinels of economic interest.

Jan 1, 1981

By Guan-zhou Qiu, Shui-shi Liu, Yu-feng Guo, Tao Jiang

"The preparation of high-quality synthetic ruitle from electric furnace titanium slag was systematically investigated by activation roasting followed by acid leaching process. The results showed that impurities such as Ca and Mg in titanium slag can be effectively removed and TiO2 grade of the product was markedly improved by the process. High-quality synthetic rutile containing 88.54% TiO2, 0.42% (CaO+MgO) was obtained under the conditions that roasted with 7.5%(wt) H3PO4 at 1000 oC for 2h, followed by two-stage leaching in boiling dilute sulfuric acid for 2h. Mechanism studies showed that anosovite solid solution and silicate minerals were reacted with phosphoric acid in the roasting process. As a result, titanium components in titanium slag turned into rutile (TiO2) and impurities were transformed into acid-soluble phosphate and quartz.IntroductionWith the gradual depletion of natural rutile and the rapid development of titanium industry in China, the natural rutile reserves cannot satisfy the requirement for production of titanium pigment and titanium sponge. Ilmenite is, therefore, becoming main raw material for titanium industry. However, because of its low TiO2 grade, it generally requires preconcentration to titanium-rich material such as titanium slag or synthetic rutile [1-3].Ilmenite resources are extremely rich in Pan-xi area of China, which account for 90.54% of total ilmenite reserves in China [4]. The titanium slag produced by electric smelting of ilmenite concentrate has high contents of Ca and Mg, and is not suitable as a raw material for chloride process and titanium sponge production. Therefore, upgrading titanium slag to prepare raw material suitable for chloride process and titanium sponge production has important significance for the development of China's titanium industry."

Jan 1, 2011

By Zhigan Deng

Cooling crystallization was used to separate iron (III) and nickel (II) from acidic sulfate solution produced by leaching of molybdenum-nickel black shale. The effect of K2SO4 concentration, crystallization temperature, solution pH and crystallization time on recovery of nickel (II) and precipitation of iron (III) was investigated, in order to obtain effective separation of nickel and iron. The optimum parameters determined were as follows: 200 g/L K2SO4, 10 °C crystallization temperature, solution pH of 0.5 and 24 h crystallization. Under these conditions, 97.6% nickel (II) was recovered as K2Ni(SO4)2, 6H2O crystals and only 2.0% of the total iron (III) was precipitated. Recrystallization yielded K2Ni(SO4)2, 6H2O crystals with a purity of 98.4%.

By Wei Lv, Xuewei Lv, Senwei Xuan, Chenguang Bai, Kai Tang

The contact angle between six iron ores and water were determined by the capillary pressure method with cyclohexane as the perfect wetting liquid. The factors influencing the contact angle were discussed, and a relationship between the content of oxy–hydroxides and the contact angle of iron ores was obtained. The results show that the ore F has the lowest contact angle but the ore D get the biggest, which are 32.09° and 78.16°, respectively. The volume fraction of oxy–hydroxides is linearly dependent on the contact angle. The contact angle decreased with increasing the volume fraction of Fe2O3*H2O.

Mar 1, 2017

By Kenneth McGowan

"The aluminum industry is the 5th largest consumer of energy and the largest consumer of energy on a per-weight basis. Process heating accounts for 25% of the energy consumed to manufacture aluminum. Consequently, the generation of this energy results in the production of a significant amount of CO2 (over 3.75 million metric tons in 2003)1. As a result, the Aluminum Industry Technology Roadmap of 2003 listed the development of improved refractory materials as a goal to reduce energy use and decrease greenhouse gas creation. The result of a R&D effort addressing this desire is the development of patented microporous refractory materials for metal contact applications in all furnace areas including the belly band. It has been demonstrated that this material can reduce energy consumption up to 38% in furnaces and significantly reduce heat loss in launder and trough systems. Furthermore the material developed is non-wetting and remains un-penetrated by metal throughout its lifetime. The material does not contribute to the formation of corundum. As a result, the energy efficiency of an older lining remains intact compared to standard refractory materials which may have an initial high insulating value (such as lightweights and board) or standard dense refractory (even with penetration inhibitors) both of which show a rapid increase in thermal conductivity as the refractory is penetrated with aluminum and formed corundumIntroductionThe aluminum industry is the second largest producer of metal in the United States, behind the iron and steel industry. It is the 5th largest consumer of energy and the largest consumer of energy on a per-weight basis. Process heating is required to melt, hold, purify, alloy, and heat treat the metal and accounts for 25% of the energy consumed to manufacture aluminum. As such, process heating is the second largest energy consuming operation. Smelting, which utilizes an electrolytic reduction process is the largest energy consuming operation1.Most process heating is accomplished through the use of fossil fuels, either directly or indirectly. The choice of fuel is dependent on a plant’s location and fossil fuel availability. Table I shows the processes impacted by refractories and the calculated BTU’s generated by usage of the respective fuels as well as the Metric Tons (MT) of metal passed through each process in 20001."

Jan 1, 2009

By Wei Yu, Tiejun Chun, Jian Pan, Deqing Zhu

In this paper, the technology of producing fluxed pellets by using hydrated lime as binder instead of bentonite was carried out. Green balls with 0.8% bentonite and others with 2% hydrated lime were obtained under the same conditions of 1.5% coke, 1.45 basicity and balling at 8.5% moisture for 13 min in disc pelletizer. The properties of two types green balls were as follows: drop numbers of 4.8 to 5.0 times/0.5m, compressive strength of 19.7 to 24.2 N/pellet and thermal shock temperature of 280 to 385?, respectively. Comparing with bentonite as binder, the compressive strength of fired pellets with hydrated lime is elevated by 13.8% and climbs up to 3113 N/pellet under the following conditions: preheating at 1050? for 10 min and firing at 1300? for 15 min. The hydrated lime also improves the metallurgical performance of fired pellets. The reduction index was enhanced from 68.6% to 70.6%, RDI+3.15 increased from 90.1% to 98.8% and reduction swelling index dropped from 22.4% to 7.4%, respectively. Therefore, hydrated lime can not only replace bentonite as binder to enhance the firing behaviors of green balls, but also effectively improve the metallurgical performance of fluxed pellets which can be used as high quality feed for blast furnace.

Jan 1, 2011

By S. N. Monteiro, E. B. Zanelato, J. Alexandre, M. T. Marvila, A. R. G. Azevedo, G. C. Xavier

One of the parameters used in the study of mortars is the adhesion resistance, which indicate show much the mortar adhered to the substrate. The usual study is done at 28 days, to worldwide standardization. Few researchers study the adhesion of mortars to ages other than 28 days. In this scenario, the adhesion strength tests of conventional mortar with a 1:1:6 mass scale (cement, and sand) at 7, 14, 28, 56, 91, 182 and 364 days were performed in order to understand the behavior of this material. The usual characterization tests of the mortars were carried out to correlate the values obtained with the adhesion results. The obtained results demonstrate that the mortar continues to gain resistance with the passage of time. For the trait studied the gain was considerable, indicating that over time the cement continues to hydrate, reacting and contributing to the strength of the material.

Mar 1, 2018

By Dominik Hofer

A broad spectrum of tantalum containing input materials can be processed for the production of synthetic tantalum concentrate (“SynCon”). The use of these low grade substances offers a secure alternative to mining of coltan in Central Africa. SynCon is produced in a multi-stage pyrometallurgical process, wherefore the melting behaviour of slags presents an important factor especially regarding the energy consumption and its optimisation. The characteristics of a slag comprising mostly Al2O3, CaO, SiO2 and MgO are influenced by the amount of other oxidic constituents which enfolds the main focus of this study. A hot stage microscope serves for the investigation of the slag behaviour in a temperature range from 1000 to 1600 °C under reducing atmosphere (CO/CO2 gas). The experimental results are compared with thermodynamic calculations (FactSage) to get a better understanding of the process.

By Petrus Christiaan Pistorius, Farzin Fatollahi-Fard

The production of synthetic rutile—a common starting material for most titanium production processes—from iron-rich titanium minerals such as pseudorutile and ilmenite is described. The process for “upgrading” the mineral to synthetic rutile is by carbothermal reduction of the mineral while immersed in a molten salt at high temperature, followed by magnetic separation of the reduced iron. A variety of factors are also investigated, such as particle size of the mineral, the type of mineral, and the molten salt used. The solubility of iron(III) oxide in different molten salts is also experimentally determined.

Jan 1, 2016

By T. DebRoy

In recent years rapid technological advances have been achieved in the application of high energy density heat sources such as lasers and electron beams in diverse metals processing operations such as metal refining, fabrication, coating, surface modification and alloying. However, our phenomenological understanding of these new and emerging processes has not kept pace with the technological achievements. Inadequate understanding of plasma-metal interactions, the complexity of the component physical processes, and the scarcity of thermophysical data at temperatures much higher than the melting points of metals are the main difficulties in the comprehensive analysis of these processes. Several unique contemporary issues related to metals processing with high energy density beams such as rapid evaporation of alloying elements during processing and the role of plasma in influencing vaporization rate interfacial tension and species solubility in metals are discussed in this paper.

Jan 1, 1993

By Alice Barreto Bevitori, Felipe Perissé Duarte Lopes, Denise Cristina Oliveira Nascimento, Sergio Neves Monteiro, Isabela Leão Amaral da Silva

"The piassava fiber is one of the most rigid natural lignocellulosic fibers, which has since the last decade been investigated as possible reinforcement for polymeric composites. In the present work, the tensile properties of polyester composites reinforced with piassava fibers with thinner diameters were investigated. Composites with volume fractions up to 30% of continuous and aligned piassava fibers were tensile tested at room temperature to evaluate the ultimate strength, elastic modulus and total strain. For each volume fraction, individually separated fibers with the smaller diameters were tested. The results indicated that the tensile properties tend to improve with increasing volume fraction of the thinner piassava fibers. The role played by the fiber/matrix interaction was analyzed by scanning electron microscopy.IntroductionA significant change in the transportation sectors mainly the aerospace and automotive, occurred last century with the introduction of stronger and lighter materials. The most relevant example was the polymer composite reinforced with synthetic fiber. They are nowadays replacing conventional materials such as the aluminum alloys in airplane body owing to superior specific strength. in recent years, however, environmental problems in a global scale are imposing a reversion in the use of synthetic fiber specially the glass fiber. In spite of its higher specific strength, this fiber and its polymer composites can neither be recycled nor incinerated in a thermal plant to generate electricity [1]. Moreover, the fabrication, processing and transportation of a glass fiber composite are associated with C02emission, the major responsible for global warming [2].A possible substitute for glass fiber without the above-mentioned environmental problems, could be a natural fiber. In fact, natural fibers obtained from cellulose-rich plants, also called lignocellulosic fiber, are already being used in several engineering fields, particularly the automobile industry [3-6]. Figure 1 illustrates an automobile and its many components made of lignocellulosic fiber composite [7]."

Jan 1, 2011

By R. W. Charles

The Los Alamos National Laboratory, under the sponsorship of the U.S. Department of Energy; is involved with laboratory and field experiments to assist in development of the Hot Dry Rock concept of geothermal energy. The field program consists of experiments in which hot rock of low permeability is hydraulically fractured between two wellbores. Water is circulated from one well to the other through the fractured hot rock. Our field experiments are designed to test reservoir engineering parameters such as heat-extraction rates, water-loss rates, flow characteristics including impedance and buoyancy, seismic activity, and fluid chemistry. Laboratory experiments were designed to provide information on the mineral-water reactivity encountered during the field program. Two experimental circulation systems tested the rates of dissolution and alteration during dynamic flow. SOlubil ity of rock in agitated systems was studied. Moreover, pure minerals, samples of the granodiorite from the actual reservoir, and Tijeras Canyon granite have been reacted with distilled water and various solutions of NaCl, NaOH, and Na.CO.. The results of these experimental systems are compared to the observations made in field experiments done within the hot dry rock reservoir at a depth of approxi-mately 3 km where the initial rock temperature was 150 to 200°C.

Jan 1, 1981

By R. H. Crist

Reactive components of algal cell walls include uronic and alginic acids: In addition, many marine species have half ester sulfate groups which function as fixed anions. Associated metals vary with the media, eg., Ca and Mg in fresh water (FV) and Na, Ca, Mg in seawater. . These metals readily exchange with aqueous phase protons or metal cations. A plot of the total amount of metal cations displaced by protons vs .. pH shows one inflection at pH 4 for FV algae and' in addition a second inflection at pH 2, 3 for marine algae. The first inflection is interpreted as. Indicating the cations associated with carboxyl groups ,and the ,second with half ester ?Sulfate groups. The exchange capacities of various aigal ,species vary widely. When FV algae is placed in a Pb2+ solution,- the amount of Pb2"' deposited on the algae is. Equivalent to the. Total Ca2?, Mg2, and H+ displaced? thereby confirming the ion exchange mechanism. Ion exchange equilibrium constants are reported for the displacement of ca2+ from Vaucheria. With Mg2+, sr2+, Cd2+, Pb2+_ and Na+ as well as the reverse reactions. Cd2+ can .be removed partially from algae by precipitating it as CdS or Cd(OH) 2 Pb2+ and Cu2+ are also partially removed as the hydroxides. Rates of reaction for various alkali hydroxides decrease with increasing .unhydrated cation radius. It is concluded that theory is useful in predicting viable applications for algae in pollution abatement.

Jan 1, 1991

By Ragnhild E. Aune, Mark William Kennedy, Shahid Akhtar, Jon Arne Bakken

"To determine the heating rate of billets using ‘short coils’, an appropriate correction factor must be applied to the theoretical relationship. In 1945, Vaughan and Williamson published a semi-empirically modified Nagaoka coefficient applicable for moderate frequency induction heating processes (10 kHz). Recently it was demonstrated that the method of Vaughan and Williamson gives <10% error in the estimated power when heating aluminum billets at 50 Hz.In the present study, experiments have been conducted on aluminum billets in order to verify an empirical frequency corrected ‘short coil’ equation. Measurements of electrical conductivity (<± 0.5%), current (± 1%), heat (± 1-3%), and magnetic flux density (± 1-2%) have been performed. The results are compared with 1D analytical calculations, and 2D axial symmetric FEM modeling using COMSOL 4.2®. The frequency corrected equation has proven to provide accurate predictions of power (<4% error) within the frequency range 50 Hz to 500 kHz.IntroductionInduction heating is commonly applied to the re-heating of billets before forging or extrusion processes. The resistive heating produced by eddy currents in the solid or semi-solid work piece during this procedure, is driven by the time varying magnetic flux density in the air-gap between the work piece and the coil. The flux in the air-gap is created by the current flowing in the induction coil, i.e. the magneto-motive force. In Figure 1 it can be seen that the currents present in the work piece are concentrated in the outer ‘shell’, or the first electromagnetic penetration depth (dw), and flow in a direction which opposes the magnetic field produced by the induction coil."

Jan 1, 2012

By Kazutoshi Haga, Atsushi Shibayama, Altansukh Batnasan

This study presents a viable approach for recovery of precious metals such as gold (Au), silver (Ag), palladium (Pd), and base metals, including copper (Cu), nickel (Ni), cobalt (Co), lead (Pb) and zinc (Zn) from waste printed circuit boards (WPCBs) via iodine-iodide leaching and precipitation. The behaviours of dissolution and precipitation of precious and base metals during iodine-iodide leaching and precipitation processes were discussed. Sodium hydroxide (NaOH) was used to remove base metal impurities exist in the pregnant leach solution under alkaline conditions. Precious metals remained in the resulting solution from NaOH precipitation were recovered by reduction using ascorbic acid (L-AA) solution. Results show that under optimum leaching conditions, almost all (> 99%) of Au was dissolved in an iodine-iodide solution when the dissolution efficiencies of other precious metals (Ag, Pd) and base metals, besides calcium (leaching of 25%) were less than 1 and 6%, respectively. The study revealed that more than 95% of Cu, Ni, Pb, Zn, Fe and Mn were initially removed from the pregnant leach solution at pH of 9.3 with addition of 0.1 M NaOH. Then 99.8% Au, 81.7% Ag and 74% Pd were precipitated from the obtained solution after NaOH precipitation while L-AA dose was 0.6 ml/ml at the condition. It can be concluded that the precious and base metals could be recovered selectively and economically from WPCBs via iodine-iodide leaching followed by precipitation using NaOH and L-AA.

Mar 1, 2018