Search Documents

By Reza Ghomashchi

Casting is the most economical route to transfer raw materials into readily usable components. The economics of casting would be more pronounced and better realized, if there are no or limited necessary post fabrication treatments. Therefore, there is an urge towards near or net-shaped casting as there are significant advantages over conventional casting including reduction of component weight, excellent surface finish, higher strength and integrity of the as-cast parts, closer tolerance, and the ability to produce pore-free parts by controlling the solidification shrinkage. The concept of near or net-shaped casting is currently employed for both semi-finished products such as strip-casting and finished shaped casting, as in case of high pressure die casting or squeeze casting. The full potential of this process yet to be explored and is expected to be realized within the next 10 years, especially in case of strip casting. The current article discusses different near or net-shaped casting routes currently employed for fabrication of high integrity finished products with main emphasis on aluminum-silicon alloys. In this regard, attempts will be made to identify the key parameters during fabrication and highlight the importance of process control and optimization in fabricating premium quality cast products. Keywords: Near Net Shape casting, Solidification, die casting, squeeze casting, rheocasting, thixocasting

Jan 1, 2003

By Yasuhiro Konishi, Yoshiyuki Noda

"This paper describes a new processing of rare-earth oxide precursor, in which rare-earth carbonate powders are precipitated directly from emulsions of rare-earth loaded carboxylate solutions, using CO2 gas and water. This synthetic route of rare earth carbonate is a combined process of the stripping and precipitation stages in a conventional solvent extraction. Using this technique, lanthanum carbonate and yttrium carbonate were prepared at temperatures of 10 to 80°C and CO2 pressures of 0.1 to 3.0 MPa for 120 min. The rates of carbonate precipitation in a batch autoclave were sensitive to processing parameters such as CO2 pressure, temperature, and organic-phase composition. The particle size distributions of the carbonate powders were markedly dependent on temperature and C02 pressure.IntroductionSolvent extraction is the most appropriate commercial technology for separation and purification of rare earths. In typical commercial processes, the rare earths are stripped from loaded solvent extractants using aqueous solutions of mineral acid. After adjusting the pH of the aqueous strip solution, the rare earths are precipitated as insoluble powders of oxalates or carbonates, from which oxides can be produced by calcination. Such conventional processing can be simplified when the stripping and precipitation stages are combined by emulsifying rare-earth loaded solvent extractant with aqueous oxalic acid solution. It is likely that the single-stage precipitation stripping results in a marked decline in the consumed amounts of precipitating and neutralizing agents, thereby saving on both running and capital costs.Yoon and Doyle1) first demonstrated that oxalate powders of lanthanum and yttrium are directly precipitated from rare-earth loaded carboxylic acid solvent extractant when contacted with aqueous oxalic acid solution at ambient temperature and atmospheric pressure. Yttrium oxalate pow4ers were also prepared by precipitation stripping of di-(2 ethylhexyl) phosphoric acid. (D2EHPA) extractant using oxalic acid-hydrochloric acid solutions. 2) Moreover, neodymium oxalates were directly precipitated from organic solutions of tertiary aliphatic monocarboxylic acid and 2-ethylhexyl phosphonic acid mono-2- ethylhexyl ester using aqueous oxalic acid solutions, and powder characteristics of the resulting oxalates were compared with those of powders by the conventional solvent extraction routes. 3 • 4) Recently, attention has been directed towards the influence of processing parameters on the particle size distributions of yttrium oxalate precipitates. 5)"

Jan 1, 2000

By Wilhelm Wendt

About five years ago we showed that it is possible to use the spectral in- formation in the light emitted by the off-gas flame of a PS converter for on-line production control. Very recently measurements have been performed using improved optical equipment and data evaluation software, resulting in both improved accuracy and the establishment of new optical process parameters. Using the optical signals the slag heats could be stopped at a predetermined Cu content of the white metal with an accuracy of +0.2% Cu m the range 74-78% Cu. A good correlation was found between the slag composition and optical data, providing a possibility for on-line monitoring of the SiO2 content of the slag. The measurements indicate the possibility of predicting the optimum end-point of the copper-making stage and having real time information on the impurity removal. Factors influencing the optical parameters, such as blowrate, Pb content, temperature etc. will be discussed.

Jan 1, 1993

By E. W. Lithgow

Commercial volumes of nickeliferous laterite ores overlie part of a 90 km long belt of peridotites in central Dominican Republic. Protores are serpentinized harzburgites and dunites, with lesser serpentinite. The ore mineralogy consists mostly of goethite, serpentine-group minerals, quartz and poorly crystallized, x- ray amorphous materials. Minor constituents are hematite, gibbsite, olivine and enstatite. In the Ore Dressing plant the mine feed is subjected initially to proper sizing and blending to produce a homogenized mix. Subsequent drying and upgrading, by selective crushing and screening of rock fragments through a Barmac circuit, complete preparation of the ore for pyrometallurgical processing.

Jan 1, 1993

By I. Gaballah

Cadmium is toxic to plant, animals and humans. The council directive of the European Communities No 8315 13lEEC has fixed an upper limit of 200 ppb for the release of cadmium in industrial effluents. The conventional method of neutralization/prccipitation ( NIP ) is inefficient to reach this limit. The objective of this study is to test the efficiency of the trees modified bark to remove cadmium cations from industrial effluents after the conventional treatment by NIP. Laboratory scale tests with synthetic solutions show that the cadmium removal depends upon pH and initial concentration. About 99.9 %, 99 % and 96 % of the metal are removed from synthetic solutions containing 10, 100 and 1000 ppm respectively. Pilot plant trials ( 1 m3 ) with an industrial effluent bearing about 500 ppb of cadmium lead to the almost complete elimination of the cadmium ( final concentration is lower than the analytical detection limits < 20 ppb ).

Jan 1, 1994

By D. F. Suarez

Spontaneous nodulation leading to growth of well developed glossy spheroids (generally hemispheres) of up to 0.06 cm width in 120 min has been observed during copper electrodeposition with certain levels of glue, thiourea and C1-. Thiourea alone can produce spontaneous nodulation but addition of glue and/or Cl- is required for rapid and sustained growth. In most cases once the glossy nodules develop they consume the majority of the copper deposited; thus, the specific current densities (and hence copper electrodeposition rates) on the glossy nodules are about an order of magnitude or, more greater than on the adjacent planar surfaces. The texture of the adjaoent planar surfaces is not glossy in appearance but is well faceted showing the usual deposition grain structure for such additives. Cathode potentials when spontaneous nodulation occurs are about TOO my more negative than with usual copper electroplating. This fact associated with evidence of extremely high levels of cathode surface passivation based on cyclic voltammograms indicates that the conditions which lead to spontaneous nodulation result from a very tightly adsorbed additive surface film. This film breaks down in specific points initiating the glossy nodules which then grow at extremely rapid rates. Current density is also important in spontaneous nodulation. At equal deposition times a current density of 21.5 mA/cm produced much larger glossy nodules than at 48 mA/cm2. The surface concentration of the glossy nodules was much greater in the latter case, however. The role of current density is still not well understood. The role of it as well as the relative roles of the three additives, thiourea, glue and Cl- in spontaneous nodulation is presented. Preliminary results and some possible correlations of these to help explain spontaneous nodulation are presented. It is believed that tankhouse upsets where cathode nodulation occurs may be related to this phenomenon.

Jan 1, 1987

By Larry Southwick

This Peirce-Smith Converting Centennial symposium is celebrating the contributions of two men, William Peirce and E.A.C. Smith, in advancing technology allowing the copper industry to realize its full potential. However, theirs is representative of a larger story: New, simpler technology releasing the stranglehold of older, more complicated technology, new developments in vessel configuration and design finding alternate routes around dead ends in operability, advances in technique and concepts removing roadblocks of cycle time and capacity, and overall innovation opening up vast new reserves around the world to those companies willing to embrace those improvements. Our story is also one of personalities, stubborn smeltermen versus the innovators, those inside the industry versus those from outside. It is a story of an initial borrowing from the steel industry, but also Peirce and Smith, from the refining end of the copper business, taking the ideas of Baggaley from Pittsburgh’s steel and airbrake industry, who built on what Hollway, Manhès and David, Douglas, and others had done in smelter tests, further to compete with the previous primacy and closely held expertise of the copper smeltermen in Wales. These advances have been well recorded in photographs taken over the last 150 years. A number were submitted especially for this symposium. Many others were published in the mining and metallurgy press of the times. Several mining schools also retained copies of photos either taken during field trips, or donated to the school by alumni and operating companies. This presentation will provide a selection and discussion from these sources of “converters in action”, describing the various designs, operations and developments depicted. The focus here will be on the first roughly 60 years of copper converter development, from Bessemer’s days at the dawn of this new idea, up to and slightly past the time of initial adoption of Peirce and Smith’s designs.

Jan 1, 2009

By Zhigang Liang

Investigation into the mixing of 150t ladle furnace by two-nozzle jetting was performed by a water model simulation of 1:4. The effects of nozzle arrangements including separation angle, radial position and asymmetry as well as tracer adding position on the mixing time were studied. The most favorable mixing is achieved when the two nozzles are symmetrically arranged at half radii in the ladle, with 45o separation angle. The empirical relationship between the mixing time and stirring power intensity has been established for two-nozzle jetting based on the present experimental results. In addition, the swelling above bath surface is also investigated with two-nozzle jetting.

Jan 1, 2009

By Ian Baker, Xavier Pierron

"Iron aluminides hold great promise for intermediate temperature applications (to ~ 600°C) because of their excellent oxidation and sulphidation resistance and good strength. However, they have poor low temperature ductility, a feature which is exacerbated by water-containing environments. This paper presents an overview of the effects of environment on the ductility of iron aluminides, including the effects of iron aluminum ratio; ternary alloying additions, particularly boron; strain rate; and temperature. The mechanisms involved in water-induced embrittlement are discussed.IntroductionOver the last few years, it has became increasingly evident that the ductility and fracture toughness of many intermetallic compounds, particularly aluminides, are reduced dramatically if they are mechanically tested in either air or in hydrogen-containing atmospheres (1-5). For FeAI and Fe3AI, it has been shown that water vapor, for example in air at room temperature, can form atomic hydrogen by reacting with the Al atoms (1, 2). As a result in iron aluminides, the environmental embrittlement process is quite similar to traditional hydrogen embrittlement. This can be easily demonstrated by either testing an iron aluminide in an environment free of the deleterious species or by testing at high strain rates, both of which result in greater ductility. The purpose of this paper is to review recent progress in understanding environmental embrittlement in FeAI and Fe3AI, and to consider possible environmental embrittlement mechanisms. Greater understanding of this phenomenon will lead ultimately to remedies to this problem which is a major reason for preventing the practical application of these materials. First, some background on the iron-rich aluminides."

Jan 1, 1996

By R. Craig McClung

Contrary to other sulfide minerals, where recovery is principally liberation controlled, the recovery of molybdenite is more complex. It is this complexity that initiated a geometallurgical investigation of molybdenites from Bingham Canyon. The aim of this investigation was to determine the effect mineralogy and/or mineralogical attributes have on recovery. All samples were analyzed using normal mineralogical techniques. The results reveal the presence of two distinctly different types of molybdenite. These have been identified as the two polytypes of molybdenite: i.e. hexagonal (2H); and rhombohedral (3R). The 2H-polytype occurs as textbook-shaped particles in quartz-molybdenite veins that are located in the current pit bottom. The 3R-polytype occurs as disseminated, “ball”-shaped particles with a dull or frosted appearance and are concentrated along the margins of the current pit. Concerning their metallurgical behavior, each type exhibits unique metallurgical properties that are consistent with those reported in the published literature. The 2H-polytype is easily ground and kinetically “faster” floating with surface attributes that are amenable to higher rates of recovery. This results in the production of a high quality concentrate under normal operating conditions. The 3R-polytype, by comparison, is difficult to grind and kinetically “slower” floating with surface attributes that are less amenable to recovery. Therefore, in deposits with higher concentrations of the 3R-polytype, modifications to the normal operating parameters may be necessary to improve recovery. This investigation highlights the necessity for understanding the mineralogical characteristics of any economic mineral(s), as these will have a direct impact on recovery.

By Bora Derin

This work deals with the recovery of valuable metals from the ancient copper smelting slags located in Küre-Turkey. In this process, copper and cobalt were recovered in metallic form and/or as their compounds, whereas iron was recovered as magnetic oxide or pigment. Abrasive grit material was produced using reduced final slag. The process stages involved carbothermal reduction in a DC arc furnace, granulation, leaching, chemical precipitation, selective sulfidizing roasting and product preparations. In this paper, the process stages were described as theoretically and experimentally whereas slag and products were characterized in detail.

Jan 1, 2003

This symposium is dedicated to the lifetime achievements of Professor H.Y. Sohn. It covers the scientific fields, processing routes and investigation techniques in which Prof. Sohn has worked during his career and is based in the equally important three topical areas: Principles, Technologies, and Industrial practice. Professor Sohn was General Chair of the very first TMS Fall Extraction and Processing Symposium in 1983 in San Francisco which led to the Annual such symposia as this International symposium. Furthermore, the theme of that symposium was sulfide smelting, which is also included in this symposium. [ ] Professor Sohn was born in a beautiful dynastic capital Kaesung, Korea on August 21, 1941. He received his B.S. degree in 1962 from Seoul National University, M.Sc. in 1966 from the University of New Brunswick, Fredericton, N.B., Canada, and his Ph.D. degree in 1970 from the University of California at Berkeley all in Chemical Engineering. After working as a Research Associate at the State University of New York at Buffalo and as a Research Engineer at Du Pont?s Engineering Technology Laboratory, Dr. Sohn joined the Department of Metallurgical Engineering at the University of Utah in 1974 and currently holds the ranks of Professor of Metallurgical Engineering and Adjunct Professor of Chemical Engineering.

Jan 1, 2006

This symposium is dedicated to the lifetime achievements of Professor H.Y. Sohn. It covers the scientific fields, processing routes and investigation techniques in which Prof. Sohn has worked during his career and is based in the equally important three topical areas: Principles, Technologies, and Industrial practice. Professor Sohn was General Chair of the very first TMS Fall Extraction and Processing Symposium in 1983 in San Francisco which led to the Annual such symposia as this International symposium. Furthermore, the theme of that symposium was sulfide smelting, which is also included in this symposium. [ ] Professor Sohn was born in a beautiful dynastic capital Kaesung, Korea on August 21, 1941. He received his B.S. degree in 1962 from Seoul National University, M.Sc. in 1966 from the University of New Brunswick, Fredericton, N.B., Canada, and his Ph.D. degree in 1970 from theUniversity of California at Berkeley all in Chemical Engineering. After working as a Research Associate at the State University of New York at Buffalo and as a Research Engineer at Du Pont?s Engineering Technology Laboratory, Dr. Sohn joined the Department of Metallurgical Engineering at the University of Utah in 1974 and currently holds the ranks of Professor of Metallurgical Engineering and Adjunct Professor of Chemical Engineering.

Jan 1, 2006

This symposium is dedicated to the lifetime achievements of Professor H.Y. Sohn. It covers the scientific fields, processing routes and investigation techniques in which Prof. Sohn has worked during his career and is based in the equally important three topical areas: Principles, Technologies, and Industrial practice. Professor Sohn was General Chair of the very first TMS Fall Extraction and Processing Symposium in 1983 in San Francisco which led to the Annual such symposia as this International symposium. Furthermore, the theme of that symposium was sulfide smelting, which is also included in this symposium. [ ] Professor Sohn was born in a beautiful dynastic capital Kaesung, Korea on August 21, 1941. He received his B.S. degree in 1962 from Seoul National University, M.Sc. in 1966 from the University of New Brunswick, Fredericton, N.B., Canada, and his Ph.D. degree in 1970 from theUniversity of California at Berkeley all in Chemical Engineering. After working as a Research Associate at the State University of New York at Buffalo and as a Research Engineer at Du Pont?s Engineering Technology Laboratory, Dr. Sohn joined the Department of Metallurgical Engineering at the University of Utah in 1974 and currently holds the ranks of Professor of Metallurgical Engineering and Adjunct Professor of Chemical Engineering.

Jan 1, 2006

This symposium is dedicated to the lifetime achievements of Professor H.Y. Sohn. It covers the scientific fields, processing routes and investigation techniques in which Prof. Sohn has worked during his career and is based in the equally important three topical areas: Principles, Technologies, and Industrial practice. Professor Sohn was General Chair of the very first TMS Fall Extraction and Processing Symposium in 1983 in San Francisco which led to the Annual such symposia as this International symposium. Furthermore, the theme of that symposium was sulfide smelting, which is also included in this symposium. [ ] Professor Sohn was born in a beautiful dynastic capital Kaesung, Korea on August 21, 1941. He received his B.S. degree in 1962 from Seoul National University, M.Sc. in 1966 from the University of New Brunswick, Fredericton, N.B., Canada, and his Ph.D. degree in 1970 from theUniversity of California at Berkeley all in Chemical Engineering. After working as a Research Associate at the State University of New York at Buffalo and as a Research Engineer at Du Pont?s Engineering Technology Laboratory, Dr. Sohn joined the Department of Metallurgical Engineering at the University of Utah in 1974 and currently holds the ranks of Professor of Metallurgical Engineering and Adjunct Professor of Chemical Engineering.

Jan 1, 2006

By J. C. Agarwal

Slags produced by modern smelting furnaces contain copper values which are unacceptably high for discard. The electric arc furnace is employed commercially to clean copper from flash furnace slags but the addition of highly oxidized converter slags to an electric furnace has created operational problems. Highly oxidized Noranda Reactor slags have not been processed successfully in a pyrometallurgical process. These slags, which contain large concentrations of copper (5 to 10 per cent), are treated in slag concentrators (controlled cooling, crushing and milling, and flotation) which produce a copper concentrate that must be resmelted. Though commercially operable, it will be shown that the slag concentrator has important process and cost disadvantages as compared to a pyrometallurgical process. In this paper an economic comparison is made between a pyrometallurgical process and the slag concentrator. For the analysis, five hypothetical smelting plants are considered. Each plant treats 1200 tons of copper concentrate per day and produces 109,000 tons of copper annually. The plant configurations used in this study are:

Jan 1, 1976

By Kafui Nyavor

Acid mine drainage (AMD) is presently the biggest single environmental problem facing the mining industry. New and expanding metal mines in most parts of the world have to demonstrate their ability to contain this problem to obtain operating permits. Conventional methods of controlling acid mine drainage have primarily been limited to collecting the drainage and neutralizing with alkaline materials which do not provide a permanent solution to the AMD problem. Since acid mine drainage results from the oxidation of sulfides in the presence of oxygen, water and iron-oxidizing bacteria, controlling any of these three factors contributing to pyrite oxidation provides a potential at-source remedy for reducing or preventing acid mine drainage formation. Physical properties such as hydrophobicity also play an important role in the attachment of bacteria, adsorption of oxygen, water, and other ions that subsequently lead to the oxidation of pyrite. In this communication, the suppression of pyrite oxidation by treatment with fatty acid amines (FAA) was investigated. The FAA treated pyrite samples were tested at various conditions of temperature and pressure. At an elevated oxygen pressure of 500 psi and a temperature of 600 C, less than 0.2% oxidation was obtained for the FAA treated pyrite samples, while over 1.2% oxidation was obtained for the untreated samples in 10 hours of oxidation time. Accelerated column oxidation tests at ambient condition showed that FAA mated samples reduced pyrite oxidation by at least 75% in 81 days.

Jan 1, 1994

By Satu Strömberg

Four different nickel concentrates were oxidized in a laboratory scale laminar flow furnace in simulated flash smelting conditions. The major nickel- and iron-bearing minerals in the con- centrates were pentlandite, violarite, gersdorffite, and pyrite and pyrrhotite, respectively. Thermal decomposition, ignition and oxidation behavior of nickel and iron sulfides were examined by using optical and scanning electron microscopy. General reactivity of the concentrates was monitored with sulfur removal which was most effective in violarite-based concentrate. Pentlandite-concentrates needed higher experimental temperatures for complete desulfurization and gersdorffite-based concentrate contained 5 - 10 % of the original sulfur even in the most oxidizing conditions studied (1 100°C, 50 vol-% 02). The reactivity of the iron minerals was found to depend on the other minerals present in the concentrate. In this paper, the observed re- action products and mineralogical changes are presented and preliminary conclusions of possible reaction mechanisms of nickel-bearing minerals are discussed.

Jan 1, 1997

By Xuan Cheng

The electrochemistry of sulfide mineral flotation is reviewed with particular emphasis on galvanic interaction among minerals and grinding media, and its relevance to flotation of complex sulfide ores is discussed. Surface alteration due to galvanic interactions among chalcopyrite, pyrrhotite and mild steel is analyzed in terms of voltammetric and chronoamperometric studies on individual minerals and through galvanic current measurements in 2- and 3- electrode combinations. The results are related to laboratory flotation behaviors of chalcopyrite-pyrrhotite mixtures simulating copper-nickel bearing Duluth gabbro.

Jan 1, 1993

This symposium is dedicated to the lifetime achievements of Professor H.Y. Sohn. It covers the scientific fields, processing routes and investigation techniques in which Prof. Sohn has worked during his career and is based in the equally important three topical areas: Principles, Technologies, and Industrial practice. Professor Sohn was General Chair of the very first TMS Fall Extraction and Processing Symposium in 1983 in San Francisco which led to the Annual such symposia as this International symposium. Furthermore, the theme of that symposium was sulfide smelting, which is also included in this symposium. [ ] Professor Sohn was born in a beautiful dynastic capital Kaesung, Korea on August 21, 1941. He received his B.S. degree in 1962 from Seoul National University, M.Sc. in 1966 from the University of New Brunswick, Fredericton, N.B., Canada, and his Ph.D. degree in 1970 from theUniversity of California at Berkeley all in Chemical Engineering. After working as a Research Associate at the State University of New York at Buffalo and as a Research Engineer at Du Pont?s Engineering Technology Laboratory, Dr. Sohn joined the Department of Metallurgical Engineering at the University of Utah in 1974 and currently holds the ranks of Professor of Metallurgical Engineering and Adjunct Professor of Chemical Engineering.

Jan 1, 2006