Search Documents

By Xuling Chen, Zhiyun Ji, Min Gan, Wenqi Li, Xiaohui Fan, Zhiyuan Yu

"Specularite and vanadium-titanomagnetite are difficult to granulate, and with the increase of their proportions, the permeability of sintering bed is deteriorated together with the combustion velocity of fuel for the shortage of air through the sintering bed, which can lower sintering speed and specific production capacity significantly. The biomass fuel has a higher combustion velocity than coke breeze, therefore the productivity of specularite and vanadium-titanomagnetite ore can be improved remarkably by replacing coke breeze partly with biomass fuel .The results showed that, when the proportion of biomass fuel replacing coke is 40%,the sintering speed and specific production capacity of 35% specularite were improved from 19.06mm/min, 1.33 t/(m2·h)to 21.45mm/min, 1.47 t/(m2·h),and that of 55% vanadium-titanomagnetite were improved from 17.23mm/min, 1.11 t/(m2·h)to 22.80mm/min, 1.44 t/(m2·h). As a conclusion, biomass fuel is effective to strengthen sintering of refractory iron ore.IntroductionThe iron and steel industry of our country has achieved significant development in the recent years. In 2010, the output of steel has reached to 0.627 billion tons. The increasing scale of iron and steel has led to rigorous domestic iron ore environment, and the reserves of hematite and magnetite that have superior sintering characteristics are on the decline with continually exploiting and utilizing [1]. Therefore, the RIO (refractory iron ores) SP (specularite) and VT (vanadium-titanomagnetite) have to be applied vastly. However, the quality of sinters can be deteriorated when utilizing RIO in high proportion due to their poor granulation and metallogenic performances [2, 3]. Generally, the ratio of SP is 3~5%,which should not exceed 10% in our country currently [4]. Though high rate of VT is adopted in PZH steel for a long time, the productivity is obviously low compared with normal sintering [5]."

Jan 1, 2012

By Xuemei Zheng, Aiyuan Ma, Guojiang Li, Tingfang Xie, Jinhui Peng, Libo Zhang

A new microwave roasting technology for the removal of Cl from zinc oxide dust is proposed in this paper. The effect of important parameters, such as roasting temperature, holding time and stirring speed, were investigated and the process conditions were optimized using response surface methodology (RSM). The experimental results show that zinc oxide dust dechlorination rate can reach more than 95.66% and meet the requirements of wet smelting electrolysis when controlling the stirring speed of 60 r/min,roasting temperature of 650 °C, holding time of 30 min. In addition, the effect of roasting temperature and holding time on removal ef ficiency of Cl was most signi ficant. As a result, the Cl content was decreased without the risk of pollution. This makes it as a good choice for a more ecological treatment of zinc secondary resources.

Mar 1, 2018

By Meifeng Zhi

Separation of uranium and molybdenum in the alkaline leach solution of a U–Mo ore was studied. A process of acidification-solvent extraction-precipitation uranium and molybdenum was determined. The influences of solution acidity and phase ratio of acidic scrubbing on separation of uranium and molybdenum were examined. The molybdenum extraction equilibrium isotherm was drawn. The results show that the separation of molybdenum and uranium can be achieved by acidifying the alkaline leach solution, solvent extracting molybdenum using trialkylamine at equilibrium pH 2.5, and scrubbing the loaded organic phase using sulfuric acid solution. The strip solution can directly precipitate ammonium molybdate. Uranium can be directly precipitated from the raffinat

By Rina Kim

There are many factors which affect the gold cyanidation mechanism— mineral composition, free cyanide and dissolved oxygen (DO) concentrations, heavy metal additions, etc. This study combines electrochemistry and surface analysis methods to examine the effectiveness of the above factors on gold cyanidation process. Three gold ore samples were used in this study. Sample 1 was a pyrite concentrate, contained mercury and silver. Sample 2 also contained sulfide minerals, including galena. Sample 3 contained pyrite with sphalerite and galena. In the case of samples 1 and 2, the presence of heavy metals enhanced gold cyanidation kinetics, though the addition of higher DO was not effective on improving the kinetics. Sample 3 showed an opposite behavior: the kinetics was not enhanced by galena, because of its relatively small amount, however, the use of higher DO made improvement in the gold leaching kinetics, likely caused by iron species generated by pyrite oxidation.

By J. B. W. Bailey

The Noranda Horne smelter in Quebec, Canada has change considerably during the last two decades to accommodate varying custom concentrate receipts, closure of the Horne mine, better working conditions, environmental programmes, new technology and increased energy and labour costs. This paper highlights the reasons for changing the smelter from two calcine charged and one wet charge reverberatory furnaces fired by coal to a smelter using. tonnage oxygen oil, natural gas and coal in a single wet charged reverberatory furnace and a Noranda Process continuous Reactor. The current operation 1 described, including three major topics; the use of oxygen/fuel burners on the charge banks of the reverberatory furnace which has increase the smelting rate from 680 to 1100 tonnes of concentrate per day; the oxygen enrichment of the Noranda Process converting air to achieve smelting rates of over 1800 tonnes of concentrate per day; the converting of the mixture of 73 percent copper matte produced from the Noranda Process and the 33 percent copper matte produced from the reverberatory furnace.

Jan 1, 1983

By A. Christlo

Short circuit detection in 1984 involved nine inspectors for production rates of 43,000 tpa. Trials indicated the feasibility of applying cell voltage monitoring to short circuit detection and improving operational efficiency. A computerised cell voltage monitoring system was commissioned in February 1986, to read voltages from 648 cells. The system incorporates 16 evenly distributed work face units which communicate with a central computer system. Provision has been made in the computer program for the automatic adjustment of cell reference voltages. This allows for the effect of polarization and other process variables which might other wise interfere with short circuit detection. The work face units can continue to work independently for several days should this become necssary. Current efficiencies have been maintained and the number of inspectors reduced from nine to five.

Jan 1, 1987

By Stephen W. Paff

The EPA has estimated that there are over 3,000 sites across the United States contaminated with lead. Techniques to remediate these sites include standard stabilization/disposal technologies, reclamation of lead using secondary lead smelters, soil washing, and biological removal technologies. In this paper, the current technologies used for lead remediation will be reviewed. Factors affecting the use of each technology, such as range of applicable concentrations, soil types, interferences from other contaminants, economics, and current technology status will be assessed. The paper will also focus on the results of a recent study completed by the Center for Hazardous Materials Research (CHMR), in conjunction with a major lead smelter, which demonstrates that secondary lead smelters may be used economically to reclaim lead from a wide range of lead-containing materials frequently found at Superfund sites. Such materials include battery case materials, lead dross, and debris containing between 3 and 70% lead. The results of development work completed by CHMR on the Acid Extraction Treatment System (AETS), which has been demonstrated to extract Lead from soils containing up to 30,000 mg/kg lead, will also be presented. The use of these technologies will be compared with other options for the remediation of sites.

Jan 1, 1994

By William A. Hockings

This report describes the results of laboratory studies on leaching of copper ores.tlf These studies are the first step of a program for the investigation of in situ leaching of tabular, metalliferous ore bodies.(2) The basic steps required in the development of an in situ process are: 1. Leachability - the ability to dissolve the metal values from the ore under in situ conditions must be demonstrated. 2. Ore Preparation - the ore must be prepared so that sufficient contact with the solution can be attained. 3. System Design - integrated in situ systems must be designed and studied for engineering feasibility. 4. Economic Feasibility - the economics of the system must be shown to be economically feasible and competitive. 5. Environmental Feasibility - the loss of reagents into the environment must be investigated. 6. Pilot Scale Testing - the feasibility of the system must be demonstrated on a sufficiently large scale. The studies described in this report were concerned only with the first step of the program, viz., leachability. Native and sulfide copper ores from the Michigan copper district were selected as model ores for these studies. Aqueous amnonia solutions were chosen as the solvents to be investigated. In this study carbonate (CO3, HCO3, H2CO3) was used exclusively as the anion. In keeping with custom it is referred to as carbon dioxide and concentrations are ex- pressed in terms of CO2. When leaching native copper the reaction is

Jan 1, 1976

By D. M. Hausen

The term "auriferous pyrite" relates to an association of gold with pyrite in a variety of textural forms that affect metallurgical treatment. Extraction of the gold depends not only on the grain size and distribution of the gold in the pyrite, but also on the crystal size and surface area of the pyrite. Occlusions of medium to coarse gold may be liberated by moderately fine grinding. The amenability of finely dispersed (submicroscopic) gold depends in part on the activity of the pyrite surface for oxidation. Two types of auriferous pyrite at Carlin, Nevada, have been examined by optical microscopy and SEM methods before and after aqueous oxidation test work to show how differences in morphological features can affect rates of oxidation and amenability to gold extractions by methods of chlorination and low temperature oxidation.

Jan 1, 1981

By Omid Marzoughi

Chromium has a wide range of applications, including as an alloy addition in various steels and also as a corrosion resistance coating. Carbothermal reduction of chromite ore (FeCr2O4) in a submerged arc furnace is an important industrial process for extracting chromium, but the energy consumption is excessive. It is suggested that one area for future research is the low temperature carbothermic solid state reduction of chromite to produce an intermediate product, which can subsequently be upgraded to ferrochromium. In this regard, a thermodynamic model has been developed to investigate this process and the effects of temperature, carbon additions and ore composition on the recovery of chromium and the grade of the ferrochromium, have been studied. Further development of the model may allow it to be applied to the simulation of other processes for the recovery of chromium from chromite ores.

By Takeo Fujino, Nobuaki Sato, Junichi Hasegawa, Masato Nakazawa, Kohta Yamada

"Tantalum oxide thin films were deposited on quartz substrates by laser ablation of Ta2O5 target using Nd:YAG pulse laser. Deposition-was observed when a laser light energy higher than 200 mJ and its repetition rate higher than 3 Hz. A thin film of 0.1 µm thickness was obtained by the ablation using a laser light of 300 mJ and 6 Hz for 2 sec. The thickness of the film increased with increasing energy, repetition rate and irradiation time of laser. By the SEM observation, it was found that many island-like particles were deposited on quartz substrate forming a thin film. The obtained thin film, which was identified as ? Ta-O by X-ray diffraction, was oxidized to Ta2O5 by the heat treatment in air at I273 K for 3 h.IntroductionTransition metal oxides have a potential to show special characteristics in electrical, magnetic and/or optical properties. When such compounds are fabricated in the form of thin film, the special properties would be improved or new characters would appear in comparison with bulk materials. Tantalum penta-oxide is widely used as a capacitor since Ta2O5 shows high dielectric constants up to high temperatures. The tantalum solid capacitor has been fabricated by the electrical oxidation of sintered Ta metal cylinder followed by MnO2 film coating. However, further improvements, reduction and layered structure formation, are required for compacting the devices. The layered structure of thin films would be applicable for the above requirements. The formation ofTa2O5 film by low pressure CVD1), photo CVD2) and magnetron sputtering3l were reported. The laser ablation -method is one of the most convenient techniques for the deposition of thin films from their compounds, such as oxides. Formation of Ta2O5 film by pulse laser deposition (PLD) method using ArF excimer4), Nd:YAG (533nm)5) and TEA CO2 6 lasers was reported. In these PLD studies, ablation was carried out in relatively high oxygen pressures resulting in formation of Ta2O 5 film. In this paper, the deposition of tantalum oxide thin film by the laser ablation of Ta2O 5 using Nd:YAG pulse laser was examined at a viliety oxygen pressures ranging from 10-8 to 10 Torr. The morphology of the films was also investigated in relation with substrate temperature and oxygen pressure."

Jan 1, 2000

By K. Yamada, T. Takaoka, A. Ozeki, M. Yamaga, Y. Kawai, S. Nishioka, Y. Kikuchi

"Recently, smelting reduction of chromium ore in BOF has been actively investigated as a key unit process for an innovative future stainless steelmaking. The prominent feature of this new process route is energy and process saving, and production cost saving. The development is already in the midst of application to the commercial production, however there still remain the following key technologies to be established for the full use of the process. One is a speed up of the reduction of chromium ore to match with sequential continuous casting, and the other is efficient combustion of carbonaceous materials in BOF to reduce their consumption, and hence to assure the steel quality. High degree of post combustion technology and new charging technology, i.e., ore-coal-flux-oxygen mixed injection, could be effective for those two subjects. In 2000 or beyond, the new process would have become quite popular owing to the establishment of those key technologies.Introduction Since stainless steel was invented, its production has continued to expand because of its attractive combinations of functions of excellent corrosion resistance, good formability, a pleasing appearance, and a wide range of strength levels. New types of stainless steels as well as new applications are continually being developed.Compared to the production of ordinary steels (1), stainless steel production (2,3) shows steady growth worldwide, while the former production remains on the same level, as Figure 1 shows. It can be estimated that future production would show further growth since materials consumer demands are more fashionable, or more functional, which could be satisfied by stainless steels.Thus market needs would be met, if it could be produced with reasonable production cost. The emergence of an innovative production technology is then potentially requested as VOD and AOD processes have emerged, which has saved substantial production cost. This paper describes a possibility of a future stainless steelmaking process, which uses the in-bath smelting reduction of chromium ore in BOF, and which would save production as well as energy cost."

Jan 1, 1988

By Fabiola Alvarez, Ana E. Bote, Daniel Pasquevich

"The oxidation of aluminum and its alloys was extensively studied for improving the corrosion resistance in structural materials having high specific strengths. But this reaction involves the formation of a very thin barrier layer on the metallic pieces. Furthermore, the ·recent development of the directed melt oxidation process for producing metal-ceramic; composites has renewed the interest in the study of interaction between gases and metals. Oxidation experiments in the presence of different chlorine partial pressures and at different temperatures were performed in ·a thermogravimetric balance, and microstructures were analyzed by electronic microscopy and X-ray diffraction. The oxy-chlorination kinetics was determined and the oxide formed W(IS amorphous at temperatures below 600 °C and crystalline .at higher temperatures. The appropriate experimental conditions for the fastest completed oxidation was further determined.IntroductionThe use of fine powders for the manufacture of ceramic components has significant advantages. They include excellent sinterability; low sintering temperature and better microstructure leading to improved mechanical properties. The conventional method of producing fine oxide powders involves controlled precipitation and pirolysis of suitable salts. The main limitation of the high temperature decomposition route is the evolution of environmentally unacceptable and corrosive gases. Controlled precipitation of hydroxides from solutions of salts, followed by thermal treatment involves large volumes of solutions and the calcination step that can induce grain growth (1).Direct oxidation of aluminum metal for producing alumina powder requires high temperatures for the direct oxidation of molten Al alloys by a vapor phase oxidant process (2, 3) or high technological process like thermal plasma reactor ( 4).Oxidation of high purity aluminum (5, 6) below the melting temperature· is initially characterized by a nearly linear reaction rate, followed by a rate which decreases rapidly with further weight gain. However, the oxidation rate of an aluminummagnesium alloy is much faster and it does not conform to any common oxidation law, but it is nearly parabolic at temperatures between 200 and 400 °C, an nearly linear· above 400 °C."

Jan 1, 2000

By J. G. Zafiratos

The leaching of a Greek low-grade manganese dioxide ore, not amenable to conventional mineral processing operations, was studied using a mixed culture of Thiobacillus sp. bacteria. The experiments were carried out in specially designed continuously aerated and stirred tank reactors arranged in two-tank series. The first tank of each series was loaded with an elemental sulfur culture suspension while the second was loaded with a manganese ore high density slurry. The bacterial culture had been previously adapted to grow on elemental sulfur and also in the presence of manganese ore and dissolved manganous ion. A two level full factorial design was constructed in order to study the effects of the ferric ion concentration in the leach solution, the "elemental sulfu weight to ore weight" ratio, the ore pulp density and the composition of the dispersed gas. The responses which were investigated included percentage manganese recovery, co-dissolution of iron and manganese dissolution rate. Parameters with constant values throughout the experiments were the leach solution pH, the nutrient medium composition, the dilution rate and the ore and sulfur grain sizes. It was found that the ferric ion concentration was the most significant factor and had a positive effect on the final percentage extraction of manganese from the ore and also on the rate of manganese solubilization from the ore. The effects of the other factors studied are discussed in detail.

Jan 1, 1997

By Guan-Yong SHI, Cong Wang, Zhi-he DOU, Ting-an ZHANG, Shi-gang FAN

Based on the pre-works, this paper proposed a new short stage process of the intensify aluminothermy reduction by the stage to prepare high titanium ferroalloy with low O and Al contents. We investigated the effects of Al and Ca and Si combination reduction agent, slag type and step-up reduction conditions on the Al content and distribution in the alloy. The results show that the step-up reduction can not only reduce effectively the oxygen content in the alloy, but also reduce effectively Al content. For instance, the oxygen content in high titanium ferroalloy is within 1%~4%, and the Al content is within 1%~5%. Its quality reaches the requirement of high titanium ferroalloy prepared by remelting process.

Jan 1, 2015

By Regina Krachler, Herbert Ipser

"The principles of the derivation of statistical-thermodynamic models to interpret the compositional variation of thermodynamic properties in non-stoichiometric intermetallic compounds are discussed. Two types of models are distinguished: the Bragg-Williams type, where the total energy of the crystal is taken as the sum of the interaction energies of all nearest-neighbor pairs of atoms, and the Wagner-Schottky type, where the internal energy, the volume, and the vibrational entropy of the crystal are assumed to be linear functions of the numbers of atoms or vacancies on the different sublattices.A Wagner-Schottky type model is used for the description of two examples with different crystal structures:For B'-FeAl (with B2-structure) defect concentrations and their variation with composition are derived from the results of measurements of the aluminum vapor pressure; the resulting values are compared with results of other independent experimental methods.For Rh3~ (with an NiAs-derivative structure) the defect mechanism responsible for nonstoichiometry is worked out by application of a theoretical model to the results of tellurium vapor pressure measurements. In addition it is shown that the shape of the activity curve indicates a certain sequence of superstructures.In principle, there are no limitations to the application of statistical thermodynamics to experimental thermodynamic data as long as these are available with sufficient accuracy, and as long as it is ensured that the distribution of the point defects is truly random, i.e. that there are no aggregates of defects."

Jan 1, 1996

By F. E. Pawlek

Copper concentrates can be comminuted in an attritor within a very short time to a particle size of 1 - 0.1 um. Addition of sodium hydroxide enhances commninution. The concentrates, suspended only in water, can be completely dissolved under oxygen over pressure and temperatures ranging from 120 - 180°C (248 - 356°F), because the surface area of the concentrate has been significantly increased by the ultra fine grinding. Addi¬tion of a small amount of silver ions to leach liquor containing sulfuric acid acted as a catalyst for the dissolution of chalcopyrite, because of the formation of local elements on the surface. The addition of C1- ions was also catalytically very effective. With this method it is possible to completely dissolve the copper contained in chalcopyrite concentrates after ultra fine grinding within 30 min at 110°C (230°F) under an oxygen partial pressure of 1 atm (14 psig). Several flowsheets demonstrate the industrial feasibility.

Jan 1, 1976

By J. Phillip Mackey

A whole new group of non-ferrous pyrometallurgical processes with the ability to utilize tonnage oxygen and capture sulphur dioxide were developed and commercialized over the period 1940s–1980s. Many of these earlier process developments were undertaken with limited knowledge of the process chemistry and influence of key process variables; in many cases, piloting helped provide much new physico-chemical data, but gaps remained. The second generation versions of these technologies of today provide all the primary copper, nickel and lead produced worldwide by pyro-metallurgical smelting. Further, process development has continued and a new generation of copper and lead smelting technologies have also been developed in China since the 1990s. The older reverberatory and blast furnaces have been progressively replaced by the newer technologies—a good example being the introduction in 1992 of the copper IsaSmelt technology at the Mt. Isa smelter in Australia where the former fluid bed roaster and reverberatory furnaces were replaced by a single new smelting unit, together with an acid plant for sulphur dioxide collection. The development of these new technologies was made possible by investment in fundamental and applied research. The lesson for the future is, in order to sustain these improvements, continued investment in research and development capability is required—to do otherwise is to risk obsolescence and lack of competiveness in the world market. Dr. Peter Hayes at The University of Queensland is one of the many researchers and process engineers who have contributed to the fundamental understanding of metallurgical processes over this period of rapid change in technologies. The present paper briefly outlines some of the many contributions Peter Hayes has made to the understanding of kinetics, mechanisms and phase equilibria in metallurgical systems, and metallurgical process development.

By Antoine Allanore, Guillaume Lambotte, Bradley R. Nakanishi

Current industrial methods used for rare earth element (REE) extraction involve: 1) ore enrichment, 2) separation of rare earth oxides (REOs), 3) chlorination or hydrofluorination, and 4) individual electrowinning of REEs from a molten halide electrolyte. The complexity of REE extraction is inherited from their electronic configuration. Recently, molten oxide electrolysis (MOE) has been used to produce reactive metals directly from their oxides, e.g. titanium. As a single-step alternative to processes 3) and 4), or laboratory has investigated rare earth extraction by MOE. A key challenge is to find a molten electrolyte more stable than REOs. One possibility is to use binaries of REOs directly as a solvent. We have, therefore, developed two experimental approaches for studying molten REOs at temperatures exceeding 2200oC. The present work reports the most recent experimental results obtained with La2O3-Y2O3. Those promising results demonstrate potential for operating with molten REOs and refine the underlying materials challenge for electrodes to enable metal recovery.

Jan 1, 2015

By Ramana G. Reddy, Yuxiang Peng

The long-term corrosion behavior of Haynes 230 (H230) alloy in MgCl2–KCl eutectic salt was evaluated at 1273 K for 500 h in Ni crucible in argon gas. The results showed H230 alloy has good corrosion resistance. In addition, corrosion was noted to occur by depletion of Cr, which was deposited on the Ni crucible. Based on the calculation of Gibbs energy of Ni-Cr alloy and exchange current density of Cr in MgCl2–KCl, the Tafel model was constructed to investigate the corrosion potential and rate. The galvanic corrosion can be explained as the predicted results were in agreement with the experimental data.

Mar 1, 2017