Search Documents

By Hirokazu Narita

Keywords: solvent extraction, precious metals, thiodiglycolamide, rapid separation, hydrochloric acid The solvent extraction of some precious metals (Pd(II), Pt(IV), Rh(III) and Au(III)) and base metals (Fe(III), Cu(II) and Zn(II)) in a hydrochloric acid solution was carried out using N,N'-dimethyl-N,N'-dioctyl-thiodiglycolamide (MOTDA) dissolved in the mixed solution of 80 vol-% dodecane and 20 vol-% 2-ethylhexanol. The extraction percentages of Pd(II) and Au(III) in the 0.01 M MOTDA-1.0 M HCl solution system are 99.6% and 71.8%, respectively. In contrast, the other metal ions are hardly extracted under the studied conditions. The Au(III) and Pd(II) extracted in the organic phase are easily back-extracted with a 1.0 M thiourea/1.0 M HCl solution. A comparison with the conventional extractant for the Pd(II) separation, di-n-hexyl sulfide (DHS), revealed that the extraction rate of Pd(II) with MOTDA is much greater than that with DHS. The extraction percentage reached over 99% in less than a 2 min contact time. However, in the DHS-Pd(II) system, it takes about 240 min to achieve the extraction equilibrium. Furthermore, MOTDA can quantitatively extract Pd(II) up to half the molar amount of MOTDA. Therefore, MOTDA is a promising extractant for Pd(II) from the HCl solution after the removal of Au(III).

Jan 1, 2005

By J. Y. Foley

Platinum-group elements (PGE) are preferentially associated with chromian spinels, including high-iron chromite, magnesian-chromian hercynite, and chromian magnetite in clinopyroxene-rich upper stratigraphic portions of the Tonsina ultramafic complex in southern Alaska. Ratios of Pt:Pt+Pd are proportional to chromium content in the associated chromian spinels. The maximum PGE content of geochemical rock samples from Dust Mountain is greater than 20.000 ppb (>0.6 oz/ton) with minor gold values. The maximum PGE content of tabled chromite concentrates is 3.430 ppb (0.1 oz/ton) at Dust Mountain. 1.029 ppb (0.03 oz/ton) at Sheep Hill, and 1,749 ppb (0.051 oz/ton) at Bernard Mountain. High-iron chromite at Dust Mountain yields tabled chromite concentrates with Cr:Fe ratios between 0.5 and 1.2. Lower PGE contents are found in more chromium-rich chromitites from Sheep Hill and Bernard Mountain that yield concentrates with Cr:Fe ratios between 1.0 and 2.8. Platinum-group minerals include amalgams. arsenides. PGE alloys, and sulfides. These minerals are between 3 and 40 microns in size and are concentrated along grain boundaries and fractures of metasomatically and hydrothermally altered chromian spinel grains.

Jan 1, 1987

By Chen Song

Keywords: Mixed extractant, Copper, Cobalt, Nickel, Synergistic effect During separation process of copper and cobalt from nickel sulphate solution, the effects of constitutions and compositions of mixed extractant D2EHPA and PC88-A or Cyanex 272, has been studied. In one step extraction cycle, the following results are obtained:[Ni]/[Co]>4000 and [Ni]/[Cu]>40000 in nickel sulphate solution, [Co]/[Ni]>1000 and [Co]/[Cu]>30000 in cobalt chlorinate solution, [Cu]/[Ni]>10000 and [Cu]/[Co]>200 in copper sulphate solution. It was elucidated that the above-mentioned synergistic mixtures can effectively separate cobalt and copper from nickel sulphate acid solution and achieve a greater synergistic effect.

Jan 1, 2005

By Jukka Tuominen

The history of making blister copper in an Outokumpu Flash Smelting Furnace dates back to the late 1960?s, when Outokumpu first piloted the Outokumpu Direct Blister (ODB) process. The first commercial scale applications have been in use at Glogow, Poland, since 1978 and at Olympic Dam, Australia, since 1988. These applications utilize special concentrates, which are low in iron, and thus the formation of slag is also low. In 1995 the same principle was applied to smelting copper matte into blister copper in industrial scale at Kennecott Utah Copper. This application, the Kennecott-Outokumpu Flash Converting process, will celebrate its 10th anniversary of commercial scale operation this year. This paper outlines the development in efficiency and flexibility of Blister Flash Smelting processes compared to other smelting and converting options. The focus is on the economical aspects i.e. on the total feasibility of both greenfield investment projects and revamping of existing smelters.

Jan 1, 2005

By A. Block-Bolten

Copper concentrates from northern Peru contain large amounts of arsenic and antimony in the form of sulfosalts like enargite, tennantite and tetrahedrite. These impurities affect up to 30% of Peruvian copper production. Under the sponsorship of the Instituto Geologico Minero y Metalurgico in Lima a project to separate copper from arsenic without pollution of the environment is being carried out at the National University of Trujillo in Peru. The U.N.T. process is unique in the respect of using .low melting salts as solvents, and sulfides of metals with high cation potential as destructors of the complex sulfosalt molecules. Laboratory scale experiments have given encouraging results but interesting and difficult problems developed on scale-up. The process is pyro-hydrometal-lurgical and under certain circumstances its economics are promising.

Jan 1, 1981

By Rick Honaker

Rare earth elements (REEs) contained in coal and associated mineral matter exist in several forms including micro-dispersed minerals, ion adsorption onto clay surfaces, and chemically bound. Tests found that REEs can be effectively recovered from certain components of three coal sources by leaching under mild conditions followed by solvent extraction. A range of pH values were evaluated at solution temperatures of 25 and 75 °C. When using 1.2 M of sulfuric acid, nearly 85% recovery of the REEs was extracted from the middlings material collected from an operating plant. Acid leaching of a second middling source from another plant resulted in 60% of the total REEs being recovered under the same leaching conditions. Solvent extraction treatment of the leachate produced from six different coal sources resulted in products containing up to 50% total REEs from feedstocks starting with around 300 ppm.

By M. Hamamoto, S. Tanaka, K. Noda

"Tamano Smelter or Hibi Kyodo Smelting Co. Ltd. is operating with the Tamano Type Flash Smelting Furnace method which is a flash smelting furnace without slag cleaning furnace but which can discharge a slag equivalent to that from the slag cleaning furnace and with the development or coke combustion technology which is the basis of this world's only one type flash smelting furnace process, the smelter exhibits a low operation cost under high productivity operation. Utilizing this experience and improving it we have developed and put to practice an operation guide system using a general purpose computer in order to further establish s stable operation. In this paper these improvements are described. Background of System DevelopmentWith the recent rapid progress of general purpose computers and improvements in their performance an environment for the use or computer in process simulation at low cost and simple operation has been established. If an accurate operation simulation can be done with the Tamano Type Flash Smelting Furnace the merits would be very great and thus we started development of the system. The official name of this system is Computer guide system for Coke Combustion in the T-FSF and taking the initial letters we call it CCCT. We aim to achieve operation with stable mane grade, temperature and slag loss in the furnace by maintaining the most suitable combustion conditions of concentrate and coke in the flash furnace with the assistance of CCCT to the flash smelting furnace operators.Through several production expansion projects clone in the past by oxygen enrichment the copper concentrate treatment quantity and matte grade have increased step by step as shown in Figure I. Following this increase the difference between the operation calculation results al the initial stage of coke combustion and the actual behavior of furnace (matte grade. temperature in the furnace. etc.) gradually became bigger. Further operation procedures taken by different operators against the same phenomenon were sometimes different depending on each individual, which from time to time caused the operation to become unstable. Prior to the development of the system we checked out thoroughly the weak points of operation calculation procedures which were in practice until that time. The results were analyzed and study was carried out to establish a most suitahle operation calculation procedure and finally we reached this system"

Jan 1, 2000

By Fang Wu

The paper designs an extraction flow for the total recovery of nickel and cobalt and removing magnesium simultaneously from the cadthodic materials of the spent hydrogen-nickel and cadmium-nickel batteries. The separation of Co, Ni and Mg though P507 extraction .The extraction equilibrium pH is 4.5~5.0, ßNi/Co is 140~180, and ß Ni/Mg is 20~25; nickel and magnesium are scrubbed in two steps, in which the equilibrium pH of nickel and magnesium scrubbing is controlled at 5.0±0.1 and 4.4±0.1 respectively. The stepwise scrubbing technique is adopted to remove 94.5% of magnesium and to recover 99.45% of nickel and 95.35% of cobalt. During the integrated extraction and precipitation process the total recovery fraction of nickel and cobalt are 99.99% and 99.95%, and the recovery fraction of magnesium is 94.02%.The recovered NiSO4 and CoSO4 solution are enriched and crystallized.

Jan 1, 2009

By Christophe Thiébaut

Keywords: Pyrochemistry, Salts Treatment, Distillation The pyrochemical purification of metal generates spent salts. When this metal is an actinide such as plutonium, the slags cannot be discarded and are thus disposed in nuclear facility. In order to handle with these slags, the decision has been taken to reduce stored quantities. The development of a pyrochemical treatment is in progress in the CEA Valduc centre. The feed salt, typically composed of various Pu and Am species contained into monovalent or divalent chloride matrix, is first oxidized to convert the actinides into oxides. Then the chlorides are separated from the actinide oxides by vacuum distillation. Temperatures higher than 750°C for monochloride salts mixture NaCl/KCl and higher than 1100°C for divalent CaCl2 base salts, are required to produce an industrial flow of vaporization. Inactive qualification of the process for NaCl/KCl base salt has been carried out with lanthanide surrogates. Then, a pilot equipment, called distillator has been designed and built for production-scale distillation of NaCl/KCl and CaCl2 oxidized plutonium salts. Industrial flows of vaporization have been obtained with this pilot equipment : about 4 g/cm²/h for NaCl/KCl at 800?900°C and 1 Pa, and more than 1,5 g/cm²/h for CaCl2 base salts between 1000?1200°C at 0.1 Pa. The last step, now in progress, is the integration of the distillator into a glove box.

Jan 1, 2005

By O. Nakai

In the copper electrorefining process, the quality of the starting sheet is one of the basic factors for producing high quality copper cathodes. A highly automated and advanced facility for the production of copper starting sheets was constructed at the Toyo Copper Refinery in 1992, bringing various improvements into an automatic stripping system using stainless steel mother blanks. In 1998, the refinery expanded the tankhouse by another 128 commercial cells, and introduced 64 polymer concrete cells in a first stage conversion. As a result, the Toyo Copper Refinery now has the capacity to produce 103,200 t/y of cathode copper. Construction has led to great improvements in the materials handling facilities and computer associated short-circuit detection technology. This report summarizes the improvements made in the quality of the cathodes and in plant productivity.

Jan 1, 1999

By Adelana Adetunji

Ilmenite ore samples obtained from Dankoli in Zamfara, North Western Nigeria has been characterized using Energy Dispersive X-ray fluorescence (EDXRF) technique, X-ray diffraction (XRD) technique and the Neutron Activation Analysis (NAA) technique. The major constituents in the ore were quantitatively found to be TiO2 and Fe2O3 in concentrations of about 60wt% and 31wt% respectively. These occur in the forms of magnesian ilmenite (Fe, Mg)(Ti, Fe)O3, pure ilmenite (FeTiO3), and barium copper yttrium oxide (Ba2Cu3YO6.56) minerals. Other constituents/impurities in minor or trace quantities include MnO, Ta2O5, Nb2O5, Wo, SnO2, Hf, Zn, V, Zr, Co, Pb, Br, Al, Rb, Y, Th and U.

Jan 1, 2006

By Ryan Walton

The Flash Converting Furnace at Kennecott Utah Copper converted over 465kmt of high-grade matte in 2002 but was restricted due to low matte production to 395kmt in 2003. This paper presents updated operational performance data and describes improvements implemented since the mid 2001 rebuild. Matte burner feed distribution, silica and arsenic impacts on settler lime-based slag operability, blister laundering, uptake/boiler accretion control, and dust sulfation will be discussed, as well as current development requirements dictated by operational imperatives and furnace modification plans.

Jan 1, 2005

By Alexander Burns

Electrolytic salt splitting is a technology where acid and/or base is regenerated from a neutral salt using membrane electrolysis. Recent advances in the understanding of brine treatment, membrane stability, and cell design have made electrolytic salt splitting feasible on certain hydrometallurgical solutions. Meanwhile, environmental regulations have made the bulk disposal of salt solutions more difficult. In this paper, sodium sulfate salt splitting is examined from a cost perspective, compared to purchasing the reagents directly. Relative costs are estimated for several regions based on published electricity and reagent prices. The results show that salt splitting is economically favourable in some regions, and can be made more favourable by applying modifications to the traditional three-compartment desig

By Jorge A. S. Tenorio, Chuanwei Zhuo, Joner O. Alves, Yiannis A. Levendis

"Reduction of combustion-emitted greenhouse gases, which are associated with global warming, may be achieved by use of CO2-neutral alternative fuels, such as bio-ethanol. Distillers Dried Grains with Solubles (DDGS) are the main co-products of the com-grain-based ethanol industries. In 2009, the North American production of ethanol from com was about 38 billion liters, which generated approximately 31.5 million tons of DDGS. Samples of DDGS were pyrolysed at temperatures of 600-1000 °C in a two-stage laminar-flow horizontal furnace, and a catalyst system was used to synthesize nanomaterials. This work presents a microstructural characterization of these nanomaterials by scanning electron microscopy (SEM) and transmission electron microscopy (TEM). Results showed that the nanomaterials produced from pyrolysis of DDGS were in the form of long, entangled, rope-like structures with rugged walls, lengths in the tens of microns, and axially non-uniform diameters in the range of 100-300 nm.IntroductionThe interest in ethanol has increased considerably worldwide due to the necessity of finding renewable and cleaner energy resources [1, 2]. According to the Renewable Fuels Association (RF A), the world ethanol production in 2008 was approximately 65.7 billion liters (17.3 billion gallons), which figure represented a 24% increase in the production over that in the previous year [3]. The major producers of ethanol are the USA and Brazil, which together account for 90% of world production. The main feedstock for ethanol in USA is com grain, whereas sugarcane predominates in Brazil [2-4]."

Jan 1, 2011

By Zhang Chuanfu, Tan Pengfu

"A thermodynamic model is developed to predict the distribution behaviors of Ni, Co, Sn, Pb, Zn, As, Sb, Bi, Au and Ag in copper pyrometallurgical process. In this model, as more as 21 elements (Cu, S, Fe, Ni, Co, Sn, As, Sb, Bi, Pb, Zn, Au, Ag, 0, N, C, H, Ca, Mg, Al, and Si) and 72 compounds (in fayalite-slag-making system) or 74 compounds (in ferrite-slag-making system) are considered. Accessory-element behavior is studied for two types of slag , fayalite and ferrite, and two levels of oxidation. The allowance is also made to account for physical entrainment in the melts.-Model simulations are carried out to study the effects of controllable process parameters such as feed composition, smelting temperature, degree of oxygen enrichment and volume of oxygen enriched air. The model can be used in copper flash process, Mitsubishi process and Noranda process. The predictions by the present computer model are compared with the known industrial data from Gui Xi Smelter in China, Home Smelter in Canada and Naoshima Smelter in Japan and excellent agreement between calculations and industrial data is obtained. In this paper, the effects of oxygen enrichment, matte grade, smelting temperature, and types of slag on accessory-element behavior among matte, slag and gaseous phase have been elucidated.I . IntroductionThe presence of trace quantities of minor elements such as As, Sb and Bi in copper significantly reduces its ductility, electrical conductivity, and lowers its thermal conductivity. Embrittlement of copper also occurs due to impurity-phase precipitates at the copper grain boundary interfaces. They deteriorate not only the electrical conductivity of copper but its workability in hot working."

Jan 1, 1998

By Fan Jiang, Haigang Wang, Shi Liu

"This paper describes several applications of Electrical Capacitance Tomography (ECT) in gassolid two phase flows. A new image reconstruction algorithm was evaluated by both simulation and experiments. It is then applied to the online measurement of solids distributions in square circulating fluidized beds (CFBs) and good results were obtained. From the measurement of solids distributions in the bottom zone of a CFB, a bubbly fluidization pattern is identified. A cross-correlation technique was combined with the solids concentration measurements to obtain the flow rate through the dip leg of the cyclone, i.e. the circulating rate of a test CFB. The same· technique was applied in a dense phase pneumatic transport pipe provides the solids concentration, and the flow rate of a wavy gas-solids flow.IntroductionElectrical capacitance tomography (ECT) has been developed for imaging multiphase distributions in the 90's of the ·last century. It is a non-intrusive method. The principle of ECT can be firefly described as follows:Firstly ECT uses a number of electrodes to surround the measuring zone, depicted by Fig. I. The capacitances between the electrodes are measured in turn and an array C is obtained that contains a total number of m independently measured capacitances. Meanwhile the measuring zone is virtually divided into a grid of n pixels, represented by an array G, named the image vector, the gray level of each pixel represents the local value of the concentration of the material. As the material distribution will be reflected by the capacitances between each pair of electrodes, such distributions can be reconstructed according to the measured capacitance, a process called image reconstruction. A common image reconstruction method is called linear-backprojection (LBP). It linearize the relationship between the dielectric distributions in the measuring zone and the capacitances between the electrodes as the following:"

Jan 1, 2004

By Melissa L. Trapani

Keywords: Copper, Taphole, Flow Instability. ?Blister spitting? is a flow irregularity where the molten blister copper stream ? or part thereof ? sprays from the taphole exit rather than following a regular flow profile to the collection box. As well as being a general ?housekeeping? issue, the unpredictable nature of the flow is a threat to operator safety. Also, the aggressive flow pattern may contribute to the mechanical wear of the taphole refractory, compromising the integrity of the taphole. This paper brings together a collection of first-hand observations and reports from process personnel, and suggests some theories as to the causes of blister spitting.

Jan 1, 2005

By Jan Pan, Deqing Zhu, Xianlin Zhou, Yanhong Luo, Zixing Xue

"Magnetic roasting process, aiming at obtaining magnetite concentrate, is the principle method of exploiting siderite as a raw material in iron and steel industry. Study on preparing DRI from siderite through coal based reduction technology is sporadic. To make the process of how siderite is reduced to iron clear, roasted ore reduced from siderite by lignite under different time periods were analyzed. The results indicated that: at the temperature of 1050°C, siderite was rapidly decomposed into magnetite, and further reduced as Fe30r?FeO?Fe, the later step was slower than the previous one. A fracture of particles was found during the process of thermal decomposition and the reduction of newly formed magnetite. As the reduction proceeded, metallization rate of products increased, and the iron grain grew along with time.IntroductionWith the rapid development of economy, China demands more and more iron ores for the iron and steel industry. China has rich iron ore resources, but 97% of them are below 30% in iron grade, many are refractory and unutilized [1], therefore large quantities of imported iron ores are in a desperate need. China imported 686 million tons of iron ore in 2011 (data from the China Customs), accounting for nearly 60% of the total consumption. To guarantee the healthy development of iron and steel industry, domestic refractory iron ores have to be utilized both economically and environmentally."

Jan 1, 2013

By Jorge A. S. Tenorio, Chuanwei Zhuo, Joner O. Alves, Yiannis A. Levendis

"The disposal of wastes is a serious environmental problem, since available landfill space is dwindling. Their treatment by pyrolysis or combustion has merit, and the corresponding fuel or power production is of technological interest. However, such processes need a rigid control of emissions. This work addresses the gaseous light hydrocarbons (LHCs) generated during sequential pyrolysis and partial oxidation of unserviceable tires, PET bottles, com wastes (DDGS) and sugarcane bagasse in a two-stage laminar-flow horizontal furnace, kept at 1000 °C. Gas chromatography was used to identify and quantify the components of the emitted gaseous light hydrocarbons. The results showed that the biomass residues generated the highest emissions of aliphatic hydrocarbons, whereas PET generated the most aromatic hydrocarbons. When stainless steel meshes were inserted in the exhaust flow, it was found that hydrocarbon emissions were curtailed; as such meshes catalyzed partial conversion of these carbon-bearing gases to carbonaceous nanomaterials.IntroductionLight hydrocarbons (LHCs) are volatile organic compounds, consisting of hydrogen and carbon with low molecular weight; the most common species are methane, ethane, propane, butane, etc. LHCs are valuable since they are a very important energy resource. However, uncontrolled release of light hydrocarbon gases to the atmosphere should be avoided [l, 2]. In this work, a development is presented for the evaluation of LHCs generated during the controlled pyrolysis/combustion of several wastes in a two-stage laminar-flow horizontal furnace. Samples of unserviceable tires, post-consumer PET bottles and waste residues from the bioethanol industry (DDGS and sugarcane bagasse) were burned. A catalyst system, consisting of stainless steel screens, was tested for its effects on the gaseous emissions."

Jan 1, 2011

By M. Hochenhofer

Due to economic aspects and environmental regulations recycling of slag and waste from ferroalloy production became a very important issue for the companies during the last years. The treatment of slag depends prior on the composition, especially on their content of valuable metals and impurities. The final aim should be a total re-use of these materials in the industry e.g. cement industry, pig-iron production etc.. Therefore, to reach the required physical and chemical properties for a further use, possibilities of a metallurgical treatment have been investigated. The conditioning of slag with a high V-, Mo- and P-content via reducing metal bath showed to be one alternative. To determine the optimal process parameters, practical investigations with different slag compositions and thermodynamic calculations were carried out.

Jan 1, 2006