Search Documents

By Scott A. Howard

MgO is routinely used as the basis for refractory materials, however, its susceptibility to hydration may result in dimensional instability and subsequent failure. The addition of boron has been shown to reduce th,e hydration susceptibility of MgO yet its dissolution into certain grades of steel may degrade their performance. In order to predict the efficacy of reducing hydration susceptibility by the incorporation of mono-, di-and tri-and quadravalent cations, the lattices of various cation-substituted systems were modeled. To more accurately simulate the substituted lattices, either cation or anion vacancies were incorporated to maintain electrical neutrality and all possible arrangements of defects in a 2x2x2 MgO supercell were investigated. Correlations were then made between the lattice energies of these systems and their susceptibility to hydration as reported in the literature. The results indicate the presence of higher charged cations tended to increase lattice stability while the cations with lower valency tended to have lower lattice energies. The relatively small body of experimental results available in the literature are consistent' with this study's results.

Jan 1, 1989

By C. D. Chapman

Current regulations regarding the landfill disposal of asbestos containing wastes are inadequate to ensure there are no ground water or airborne emissions. Accordingly, there is growing recognition that asbestos wastes can only be safely disposed of by using techniques that destroy the hazardous fibres. An innovative high-temperature plasma arc technology (The MAGRAM Process) is being developed for the recovery of magnesium metal from asbestos together with supplementary magnesia containing feedstock. The furnace will operate in. open bath mode with aluminium and/or ferrosilicon being employed as reductant. An important advantage of the process is that magnesium vapour within the furnace will be generated close to atmospheric pressure rather than at reduced pressure under which existing processes operate. Thermodynamic modelling work has been undertaken to define the range of slag composition and furnace temperature under which magnesium production at atmospheric pressure is feasible. The effect of slag chemistry, reductant addition, and temperature on product quality and yield have also been investigated and key aspects have been tested on bench scale. A 300 kW pilot plasma furnace unit has been employed for the treatment of calcined asbestos wastes. Aspects of design and operation of the unit are detailed. Acknowledgement: This work is substantially financially supported by the European Communities under the Industrial and Materials Technologies (Brite EuRam H) Research and Development programme.

Jan 1, 1995

By Dean David

The evaluation of a new mineral sands prospect with unusual characteristics is described, The heavy minerals are very fine grained, have comparatively low average specific gravity (3.6) and are altered. Poor performance by conventional processing techniques made it necessary to trace the response of the major minerals during the separation processes, QEM*SEM® was used to quantify mineral volumetric abundances and mineral locking in magnetic and gravity separation products.

Jan 1, 1989

By Rodney L. Williamson

Vacuum arc remelting (V AR) is an industrial metallurgical process widely used throughout the specialty metals industry to cast large alloy ingots. Part of the V AR control problem consists of adjusting arc current to control electrode melt rate which also depends on the electrode temperature distribution. Because the temperature distribution responds very slowly (1-4 hours depending on size and material) to changes in melt power, the melt rate response is history dependent and highly nonlinear. The situation is complicated further because measurement of the electrode temperature distribution is not practical. To solve the problem of accurate, responsive melt rate control. a low order electrode melting model has been developed and incorporated into a V AR process controller. Data from laboratory and industrial tests show that the goal of responsive, accurate melt rate control has been achieved, even when melting under highly dynamic process conditions. Keywords: Vacuum Arc Remelting. Model-Based Control

Jan 1, 2003

By David Rees

Tomago Aluminium, a 400,OO tonnes per annum primary aluminium smelter in Australia, has installed Ozone for biological control of its process water. The system was designed in Australia by Ionics Watertec Engineering, whilst ANCO Australia monitors the water quality and provides technical support for the project. The motivation was initially to reduce operating costs, however investigations indicated that there were substantial environmental benefits to be achieved by the elimination of a part, or all of, the chemicals being used to control the system. Also the existing chemicals appeared to be losing their ability to control biological growth in the system, in particular, the legionella bacteria. Ozone water treatment commenced in January 1998 and after a short transition period has operated without chemical addition since. There appears to be no doubt that the biological control is effective, the clarity and purity of the water has improved and initial testing indicates that the corrosion control rate is acceptable, although some chemical corrosion control may be introduced after further testing around the total circuit to guarantee protection

Jan 1, 1999

By R. S. Tahautdinov, A. N. Posazhennikov, V. V. Bastrygin

"The Bakal (South Ural, Russia) deposit of iron ore bearing iron carbonate (siderite) with the capacity of more than 1 billion tones belongs to the MMK. This ore cannot be fully processed via blast furnace technology because of high content of MgO. According to the investigations carried out in the USA and Japan in 1999-2004 the ITmk3 (Ironmaking Technology mark three) RHF technology is a breakthrough in Ironmaking. Four iron ore types (hematite, magnetite, high and low Al2O3/SiO2) were tested. Reduction, melting and slag removal can be achieved in just 10 min. The main objective of the investigation is to establish optimum operation conditions for the production of iron nuggets from iron carbonate bearing ore via the ITmk3 by means of the lab scale testing. Samples of iron ore and carbon reductant were chemically and physically analyzed. Green pellets were processed via a lab tube furnace to simulate RHF conditions. The nuggets and slag were chemically analyzed. This preliminary test work provides valuable information which may be used for large-scale testing in a commercially sized RHF.IntroductionThe ITmk3 process upon which this paper focuses was developed by Kobe Steel in its research facilities in 1996 [1]. After pilot testing at Kobe Steel’s Kakogava Works in 1999-2004 the pilot demonstration plant was built and operations were successfully carried out by Mesabi Nugget joint venture in 2002-2004. Steel Dynamics has committed to building the commercial plant at the Mesabi Nugget site in Hoyt Lakes (Minnesota). Only 4 iron ore types (hematite, magnetite, high Al2O3/SiO2 and low Al2O3/SiO2), as well as 4 coal types with range of volatility, ash and fixed carbon were tested. Results were consistent with nugget characteristics confirming ITmk3’s flexibility with respect to raw material inputs. At the same time, no research in the field of nugget from iron carbonate bearing ore with high content of MgO has been done. Such kind of iron ore is restricted for charging into the blast furnace due to contamination of MgO. The reason for restriction is the limitation of load of MgO in the blast furnace. If a lot of MgO enters the blast furnace, slag becomes viscous. The viscous slag is obstacle for stable operation of the blast furnace."

Jan 1, 2011

By Zhongming Ren

"A new process of near net shape continuous casting of metal pipe has been put out. The specialty of the process is that no inner core is used. The principle of the process has been presented, and the effect of several factors on the thickness of the pipe has been investigated experimentally and numerically. It is shown that the temperature and the level of the molten metal, cooling intensity of the mold, and the velocity of casting influenced the thickness of the pipe apparently. In order to improve evenness of the thickness of the pipe, the mold was dedicatedly designed, and special methods were taken. By this process, a metallic material like ""bamboo"" was fabricated.IntroductionMetal pipe is a widely used material. Up to now, many processes have been put out to produce the pipe. However, the processes are usually expensive and inefficient. For instance, the welding pipe, which is most widely used, is produced through continuous casting of slab, rolling of the slab into sheet, and welding, with several times of heating and processing. Continuous casting of pipe can not produce small diameter of pipe, which is mostly needed, due to the inner core. Even though. OCC process is novel in fabricating the pipe with small diameter, it is inefficient. In this paper, the no-inner core continuous casting of pipe was proposed. With this process, pipe with small diameter can be produced efficiently. The influence of several parameters on the thickness and evenness of piper wall. With this process, a ""bamboolike"" pipe was fabricated.ExperimentThe experimental apparatus is shown in Fig. I. It is composed of mold, furnace, melt level adjuster, and dummy pipe. In the process, the level of the melt was adjusted at a proper position, then the mold along with the dummy pipe was inserted into the melt in a certain depth. The melt in the mold began solidifying, forming a solid shell. After that, the dummy pipe was pulled upward in a certain speed, drawing the solid shell out of the mold. Thus, a pipe was continuously cast."

Jan 1, 2000

By E. V. Redin

"The Bakal (South Ural, Russia) deposit of iron ore bearing iron carbonate (siderite) with the capacity of more than 1 billion tones belongs to the MMK. This ore cannot be fully processed via blast furnace technology because of high content of MgO. According to the investigations carried out in the USA and Japan in 1999-2004 the ITmk3 (Ironmaking Technology mark three) RHF technology is a breakthrough in Ironmaking. Four iron ore types (hematite, magnetite, high and low Al2O3/SiO2) were tested. Reduction, melting and slag removal can be achieved in just 10 min. The main objective of the investigation is to establish optimum operation conditions for the production of iron nuggets from iron carbonate bearing ore via the ITmk3 by means of the lab scale testing. Green pellets were processed via a lab tube (chamber) furnace to simulate RHF conditions. This preliminary test work provides valuable information which may be used for large-scale testing in a commercially sized RHF.IntroductionThe ITmk3 process upon which this paper focuses was developed by Kobe Steel in its research facilities in 1996 [1]. After pilot testing at Kobe Steel’s Kakogava Works in 1999-2004 the pilot demonstration plant was built and operations were successfully carried out by Mesabi Nugget joint venture in 2002-2004. Steel Dynamics has committed to building the commercial plant at the Mesabi Nugget site in Hoyt Lakes (Minnesota). Only 4 iron ore types (hematite, magnetite, high Al2O3/SiO2 and low Al2O3/SiO2), as well as 4 coal types with range of volatility, ash and fixed carbon were tested. Results were consistent with nugget characteristics confirming ITmk3’s flexibility with respect to raw material inputs. At the same time, no research in the field of nugget from iron carbonate bearing ore with high content of MgO has been done. Such kind of iron ore is restricted for charging into the blast furnace due to contamination of MgO. The reason for restriction is the limitation of load of MgO in the blast furnace. If a lot of MgO enters the blast furnace, slag becomes viscous. The viscous slag is obstacle for stable operation of the blast furnace."

Jan 1, 2012

By Eiichi Kuzuno, Atsushi Shibayama, Toyohisa Fujita, Kazuo Koike, Toshio Miyazaki, Hitoshi Masuda

"A solid sulfur is more useful to recover and store than a sulfuric acid as a by-product in the zinc hydrometallurgy. In this experiment a zin concentrate (sphalerite) was leached with ferric sulfate at about 373 K for 3 to 6 hours. Zinc was leached more than 95%. After a solid-liquid separation, the leached residue contained solid sulfur was obtained. The particles in the residue were dispersed by lignin and the solid sulfur of approximately 85% was recovered as float product by a flotation with frother in the pH 4. The dried float product was heated at 413K for 2 hours. The pure solid sulfur was recovered. On the other hand in the leached liquid a zinc oxide was ·added and ferrous .iron was oxidized to ferric iron by blowing oxygen. This ferric iron was returned to the zinc leached process after solid-liquid separation.IntroductionZinc concentrate is usually roasted as pretreatment in zinc hydrometallurgy and the produced S02 is changed to sulfuric acid. However, recently in Japan the utilization of sulfuric acid has been limited and it is more costly to store. Instead of producing sulfutic acid the solid sulfur recovery has been examined by direct leaching of zinc_ concentrate in this experiment.In the direct leaching, several kinds of effects have been studied for leaching of sphalerite in ferric sulfate solution. The addition of lignine siilfonate1 • 2) and fine· grinding3) increases the · speed arid leaching fraction of sphalerite. The leaching ratio depends on impurities in sphalerite ores4 • 5). Here, the zinc concentrate is leached ferric sulfate solution under atmospheric pressure at 373K. The solid sulfur in leached residue is separated as float products from other solids by sink-float separation and flotation. The sulfur in float products is purified by evaporation at 413K and recovered."

Jan 1, 2000

By J. Alexandre

The use of bricks of soil-cement is proving to be an important constructive methodology due to low environmental impact in the production process of these blocks comparing with conventional bricks are burnt, besides being easy to produce. However during the process of production of bricks, which are compressed, knowledge of the properties of the soil used is critical to the quality and durability of the blocks. The objective of this work is to evaluate the feasibility of using soil from the municipality of Goytacazes for the production of soil-cement bricks. Assays were performed the compaction, liquid limit, plastic limit, particle size analysis, EDX and X-Ray diffraction for later pressed blocks and analyze their compressive strength and water absorption.

Jan 1, 2015

By Shaolong Chen, Carl-Gustav Berg, Hannu Mansikkaviita

Kumera Steam Dryer has been developed particularly for nonferrous metal concentrates with steam as heating source generated from waste heat boilers. Its unique structure enables the dryer to work at high capacity, up to 240 t/h, and high availability, over 95%. With half a century of engineering experience, and more than twenty industrial steam dryer installations worldwide during last 15 years, Kumera has demonstrated significant benefits of the steam drying technology in terms of energy efficiency and emission reduction to the end users. The dryer of this type can also be applied for other suitable mineral materials.

Jan 1, 2015

By Donna Post Guillen

"Cyclopentane, a flammable hydrocarbon, is being considered as a working fluid for waste heat recovery applications using Organic Rankine Cycles with Direct Evaporators. A postulated failure mode consisting of a pinhole leak in a heat exchanger tube raises safety concerns due to autoignition of the working fluid. Experiments were conducted to determine the ignition delay time (IDT) of cyclopentane using an Ignition Quality Test™ (IQT™) device. Two sets of experiments were conducted per ASTM D6890 (with exception to charge pressure and temperature) to determine ignition delay of the fuel at atmospheric pressure for standard air (-20.95% oxygen) and vitiated air (13.3% oxygen) at a temperature of 803 K. Operation of the IQT device at a much lower pressure (1 bar) than normal operation (21.4 bar) with a standard injector led to very rich conditions and wetting of the stainless steel chamber walls. Catalytic effects are postulated to produce the small IDTs observed. Experiments were repeated with a modified injector to prevent wall wetting, resulting in average IDTs that are substantially longer.IntroductionCyclopentane is being considered for use as a working fluid in a Direct Evaporator of an Organic Rankine Cycle (ORC). In this configuration, the heat exchanger is placed directly in the flow of the hot exhaust gas, rather than using a secondary heat transfer loop to isolate the flammable working fluid from the heat source. This configuration offers the advantages of approximately 15% lower cost and improved efficiency over a standard ORC. However, placing a heat exchanger operating with a flammable hydrocarbon in the hot exhaust gas stream presents potential safety risks. If a pinhole leak were to occur in the heat exchanger, working fluid could leak into the hot exhaust stream. Gas turbine exhaust is provided to the Direct Evaporator at a temperature of approximately 803 K, whereas the autoignition temperature of cyclopentane is 634 K (Gallant and Yaws, 1993). Autoignition of the working fluid has been identified as the key risk for this type of system.Autoignition occurs when sufficient self-heating by chemical reactions takes place to accelerate reaction rates to produce full-scale combustion. This is in contrast to forced ignition, in which an external source (e.g., spark) is employed to initiate the combustion process. For combustion to occur, the fuel to oxidizer concentration must be between the lower (lean) and upper (rich) flammable limits. The reaction rate depends on the species concentration of the fuel and oxidant, the local temperature and pressure. Ignition processes are comprised of steps that take a fmite amount of time. This latent period prior to the start of combustion is referred to as ignition delay time (IDT)."

Jan 1, 2012

By Larry F. McHugh

Current sulfide ore processing methods involving mechanical sizing of ores, froth flotation, electro-winning, solvent extraction, smelting and roasting are quite effective but typically represent a significant energy and environmental cost. This paper is the subject of a recent patent application and development program involving major improvements in sulfide ore processing. This two-step ?looping oxidation? process effectively removes sulfur while producing materials of adequate purity in an energy proficient and environmentally friendly manner. The first step results in a metal sub-oxide and a highly concentrated sulfur oxide off-gas stream. This gas stream can be processed for recovery in a more effective manner regarding both energy and capital equipment costs. In the second step, this metal sub-oxide is further oxidized to efficiently generate energy that can be recovered and utilized without the typical complications of an ?acid gas? stream process. Additionally, a portion of the final fully oxidized product can be looped back to the first step as the oxidizing agent. This process will be described in detail and compared to existing technologies in the area of energy efficiency, and off-gas environment treatment energy requirements.

Jan 1, 2008

By Peter Hayes, Evgueni Jak, Ata Fallah Mehrjardi

Modern analytical tools, such as electron probe X-ray microanalysis (EPMA), are used in experimental characterization of phase equilibria and microstructures of complex slags. Integrated thermodynamic computer packages, such as FactSage, are used to provide more accurate descriptions of complex slag systems. These advanced methodologies have been applied to characterize dynamic steady state freeze linings in slag systems using submerged cold finger probes at controlled laboratory conditions, establishing the effects of bath chemistry, temperature, heat extraction rate and bulk fluid flow. It has been found that stationary freeze lining deposit interface temperatures at steady state conditions can be lower than the bulk slag liquidus temperature, and that stable operation below the liquidus is possible. A conceptual framework has been developed to explain the phenomenon and the range of interface temperatures that can be obtained in dynamic steady state conditions. These findings have important implications for the design of freeze linings and possible improvements to high-temperature metallurgical operations.

Jan 1, 2014

By C. Zografidis, K. Karalis, E. Devlin, S. Tabouris

"The main parameters affecting energy and electrode consumption in smelting reduction of Greek nickeliferous laterites in submerged arc electric furnaces (E/F) were investigated. Within this framework, the operational data of E/Fs, such as energy consumption indicators, electrode consumption indicators and chemical characteristics of Fe-Ni and slag, were correlated with the physicochemical characteristics of the calcine, produced by roasting reduction of laterite in rotary kilns (R/Ks), such as reduction degree, temperature, chemical composition and granulometry. The results obtained provide a significant input for further research on the modelling of the roasting reduction – smelting reduction process, which is a critical tool for energy optimization.IntroductionThe two main steps of pyrometallurgical treatment of greek nickeliferous laterites for ferronickel production include: i) drying, pre-heating and controlled pre–reduction of laterite ores with solid fuel reducing agents and fuel oil in rotary kilns (R/Ks) for the production of a calcine, and ii) smelting reduction of the calcine in open-bath submerged-arc electric furnaces (E/Fs) for the production of Fe-Ni alloy with 12-16% Ni [1].The energy absorbed from the endothermic reductive reactions of iron, nickel and cobalt oxides (Fe2O3, FeO, NiO and CoO) of the calcine with the remaining carbon in the E/Fs, corresponds to about 16% of the total energy output in the smelting reduction step [1]. This is indicative of the significance of the calcine’s reduction degree for the electric energy requirements in the E/Fs. Moreover, the chemical characteristics and the granulometry of the calcine constitute critical parameters for the energy requirements as well as the smooth operation of the E/Fs."

Jan 1, 2012

By Dominic T. Jordan, Quinn G. Reynolds, Christopher J. Hockaday, Ian J. Barker

A direct-current (DC) plasma arc furnace is a type of electric furnace used for metallurgical operations. The successful operation of DC furnaces depends to a large extent on gaining a fundamental understanding of the arc phenomenon itself, and ensuring its presence in the furnace at all times. A method for detection of the presence of the arc in a DC circuit is presented, along with discussion of why this may be of value for certain modes of furnace operation such as brush-arc. The theoretical development of the method is presented along with supporting experimental work conducted on large-scale pilot-plant facilities.

Jan 1, 2014

By Theo Lehner

"During my first contact with industrial metallurgy as a summer vacation worker at the Steelplant at Luleå, Sweden, I came during a visit to MEFOS into contact with works of Prof. Worner caried out during the piloting of the Worcra continuous steelmaking process. These tests are still today remarkable as an innovative step in the art of metalmaking. By that they involved the necessary ingredients for the development of our art: seeing, knowing and doing. Industrial injection as applied during slag fuming will be discussed below.Phenomena of injection metallurgyPhenomenon according to Collins dictionary is"" anything that can be perceived as an occurrence or facts by the senses"". To open the senses for the interesting phenomena in pyrometallurgy must be the main task of any educator. The investigations by Engh et al. around the mixing phenomena of the WORCRA process are an early example of combining senses with knowledge. To see what you model must be a crucial part in any development. This can also involve to see and control that one is subject to the same conditions as in published models. Below the need ""to see"" will be illustrated by some recent investigations around slag fuming. In the literature various models for reactions occuring during the fuming of slags are presented. Two recent models hint ·ata) the occurrence and importance of iron for the fuming processb) the occurrence and importance of lead droplets during respectively."

Jan 1, 1996

By S. W. White

Plasma arc technology is increasingly being used to process a number of waste materials. In present research, plasma technology is being investigated to treat waste magnesium baghouse dust, which is a waste material from the Magnetherm process. This dust contains mostly MgO, but also contains NazO, CaO, and KzO. Plasma energy is to be used along with a reducing agent to produce pure gaseous magnesium while keeping the other materials in a slag. The magnesium will then be collected by rapid quenching. A non-transferred arc plasma torch is ideal for this reaction because of its high enthalpy and improved energy efficiency over conventional methods. Another advantage of plasma is that it allows for the pre-heating or pre-reacting of fine particles before contact with the melt. Thermodynamic calculations using the Gibb energy minimization method were used to determine the most stable compositions of the materials at various temperatures. Energy balances have also been calculated. These results conclude that we can recover approximately 98% of the magnesium with a proper quenching technique. The calculated results are compared with the experimental data, and good agreement between them was observed.

Jan 1, 1999

By Alan J. Hurd

"New insights into the development of microstructure in sol-gel films have recently been revealed by several diagnostic techniques, including imaging ellipsometry, ""chemical imaging"" by fluorescent tracers, light scattering from capillary waves, and finite-element modeling. The evolution of porosity during the continuous transition from dilute sol to porous solid in restricted geometries such as films and fibers is becoming clearer through fundamental understanding of evaporation dynamics and capillarity.IntroductionWith sol-gel processing, the full flexibility of solution chemistry can be exploited to make ceramic films and fibers with well controlled compositional characteristics. No less important is the ability to tune porosity and connectivity for specific applications such as optical and electrical coatings and membranes. Since the chemical and physical factors that determine the microstructure are not entirely understood, new diagnostics applied to sol-gel processing are welcome.Sol-gel films and fibers are distinguished by processing that takes a sol through continuous stages of increasing concentration and connectivity of a solid precursor. The liquid carrier is usually volatile or, at least, volatilizable through heat treatment. During deposition through states of increasing solids concentration, this sol might gel, as in bulk sol-gel processing, however, the gel state may be a fleeting transient that quickly empties of liquid. Nevertheless, the structures formed in solution during this stage influence the structure of the final solid. In particular, porosity is likely to be a remnant of networks formed in the sol-to-gel transition. Here we report on experiments whose goal is to discover the factors involved with porosity development."

Jan 1, 1994

By Olga A. Gomon, Alexey N. Lozhko

The technology of heat treatment for metal frequently includes multiple fast heating and cooling of the products surface. If the product is heavy-weight or long-size, its moving from a zone of cooling to a zone of heating and return require a long time. Other important condition of ensuring qualitative surface at heat treatment is intensification of cooling phase. It is known that turbulization of a flow activates heat exchange and increases efficacy of cooling without increasing volume flow rate of water. Additional difficulty is to ensure the regularity of heating and cooling on length of a product. The technology of cyclic heat treatment of rolling products, at which mobile zone of turbulent heat exchange is formed on the surface of a product, was developed and realized. The submission of water occurs through to face spray systems. Each of the systems has six long-range atomizers, which are located circularly. Two flows of water move towards one another along a surface of a product. When they collide, the right zone of turbulent heat exchange creates heat transfer in this zone of 10-15 time more intensive than on other surface of a product. The effect of moving turbulent zone on length of a product is reached by changing the proportion of volume flow rate of water, which is created by face sprays. The speed of movement for turbulent zone along a surface of a product is chosen so, that the cooling takes place on a small depth only. Then after passing the turbulent zone over a determined site of a surface, its temperature recovers fast owing to hot internal layers. The parameters of process were determined by mathematical simulation of cooling in an installation. The equations for dynamics of movement of collision point of flows, which were received this way, are interesting supplementary products of research. The experiments show that frequency of movement of turbulent zone is an important technological parameter. It defines mechanical properties of a surface and should be chosen depending on a profile of product and metal grade. The results of comparison of mechanical properties of a surface of various rolling products, which were received by developed and conventional technologies, are described in this report. Dependence of regularity of mechanical properties on frequency of movement of turbulent zone is adduced.

Jan 1, 1998