Search Documents

By Judy Che, Steven Ceccio, Gretar Tryggvason

"A detailed understanding of drop deformation and solidification is essential for quantitative predictions of geometry and properties of parts made by ballistic particle manufacturing processes. Axisymmetric results of towers built by the deposition of multiple drops are presented. In these computations, fluid flow, heat transfer, and phase change are fully coupled throughout the drop deformation and solidification process. The solution method is based on a single set of conservation equations written for all phases simultaneously. The phase boundaries are treated as imbedded interfaces by adding the appropriate source terms to the conservation equations. A parameter study demonstrates the effect of Weber number, Peclet number, and drop deposition frequency on the final shape of the structure. Numerical results show that most successful method of building uniform towers is when two conditions are met. First, each drop solidifies at the same time in the deformation cycle. Second, the cooling rate is slow enough to allow for good adhesion between drops. The ability to predict the final shape of deposited drops will greatly reduce the amount of experimentation necessary to select the desired set parameters for any artifact.IntroductionMaterial deposition techniques based on layering small molten metal drops holds the promise to build small, coherent three-dimensional structures. In this process, numerous 20-100 µm diameter drops are deposited onto a substrate with a low impact velocity (on the order of 5 mis). Both the momentum and trajectory of each drop are controlled precisely to build up complex parts. This material layering technique differs from processes such as spray forming and splat quenching which involve high impact velocities (on the order of 100 mis) and high frequency deposition with little control over individual drop placement. This process of layering small drops can produce parts with near net shape accuracy, while spray forming produces slabs of material which must then be worked to make a usable part. The ability to computationally predict final drop shape and cooling rate has the advantage of allowing the user to select parameters to produce parts with desired shape and mechanical properties. However, the development of such predictive methods requires a thorough understanding of both drop deformation and solidification"

Jan 1, 1999

By A. Navarra

Within conventional copper and nickel-copper sulfide smelters, ladles of molten matte are fed into converters. These converters blast oxygen-enriched air into the matte, thereby eliminating iron and sulfur. The converting reactions are exothermic and, indeed, the converter heat balance is often a limiting consideration on the smelter throughput. If a portion of the matte were fed in solidified (granulated) form, this would support higher oxygen enrichment, and lower volumes of converter offgas, allowing higher throughput. This approach is not applied in conventional smelters, partly because of the copious amounts of water that must be evaporated in typical granulators, as in the Kennecott-Outotec process. The current paper recalls a waterless matte granulator that had been pioneered in the 1990’s, and is applicable to conventional smelters. A mathematical formulation is presented that can be used in the context of simulation-based optimization, to estimate the size and impact of waterless matte granulation.

By Bruce W. Wessels

"Metal-organic chemical vapor deposition has been shown to be a highly versatile technique for the synthesis of complex oxides. High dielectric constant oxide thin films of SrTiO3, BaTiO3, Ba1-xSrxTiO3 and SrxBa1-xNb2O6 can be be be deposited at 800 ºC with this technique. The fluorine substituted B-diketonate precursors have been shown to be well-suited for the deposition of high quality, epitaxial thin films of these materials.IntroductionThere has been a resurgence of interest in thin film ferroelectric oxides as a result of the development of techniques to deposit high quality material. Both physical and chemical vapor deposition techniques have been realized. Of the chemical vapor deposition techniques, metal-organic chemical vapor deposition (MOCVD) has received the most interest for the deposition of ferroelectric oxide thin films. This results, in part, from the availability of a number of volatile metal-organic precursors.(l) Moreover, MOCVD offers the advantages of high growth rates, uniform coverage over large areas, conformability, abrupt interfaces and excellent epitaxial crystallinity. Of the metalorganic precursors, the B-diketonate complexes have played an important role especially in the deposition of ferroelectric oxides containing alkaline-earth metals such as BaTi03 and Ba1•XSrxTi03. For example, barium tetramethylheptanedionate Ba(thd)2 has been used in the preparation of BaTi03 by MOCVD.(2) These compounds, however, are not without their problems. Ba(dpm)2 has a relatively low volatility; and as a consequence, temperatures in excess of 180·C are required for volatilization. This leads to the necessity of a complex precursor delivery system to insure that the precursor does not condense before the reaction zone. Moreover, the Ba precursor tends to oligomerize leading to a decrease in vapor pressure as well as a problem with reproducibility. To counter these problems, novel liquid source and solid source precursor delivery systems have been developed. (3)(4)"

Jan 1, 1994

By G. Brooks, J. Naser, M. A. Sattar

CFD models have been developed and numerical simulations have been carried out to predict the formation of foam in oxygen steelmaking. Foam was considered as a separate phase comprising a mixture of gas and liquid. Bubble break up and coalescence models have also been incorporated in a CFD model to predict the number density of individual bubble classes. A population balance equation was used to track the number density of each bubble class. Decarburization with heat generation from chemical reactions was integrated in the process. User subroutines were written in FORTRAN to incorporate the foam formation, the bubble break up and coalescence rate and decarburisation in the main program. The model predicted the foam height, bubble number density, velocity of phases, decarburization, and turbulence. The result from the model has been compared with available data from literature and found to be in reasonable agreement with the experimental and plant data.

Jan 1, 2014

By B. J. Jody

This paper describes a one-step thennal-treatment process, developed at Argonne National Laboratory, to remove all organic contaminants from the glass-fiber waste that is generated during the glass-fonning process. The recovcred glass fibers can then be recycled into new glass fibers or new glass products without adversely impacting the operations of the glass industry or the quality of its products. Our process involves shredding the waste to a manageable size and then processing it at temperatures below its melting point to remove the polymeric-coating layer. The glass industry generates more than 60,000 tons of glass-manufacturing waste annually in the glass-forming process alone. Recycling of this waste stream can keep this non-biodegradable waste out of the landfills. In addition, use of recycled glass lowers energy costs, by an average of about $5 per ton as compared to using virgin raw materials to make virgin glass fibers. This process will also reduce the emission of C02 by 17,400 tons a year and it will also reduce the emission of nitrogen oxides. Economic analysis of our process shows a potential payback of less than 2 years.

Jan 1, 2003

By G. Springer

The identification of lost mineral values in mill tailings frequently requires the inspection of hundreds of thousands to millions of particles. The search of these particles can be made automatic by using an electron microprobe. A standard instrument (Cambridge Mark V) was modified by the addition of stepping motors to advance the specimen stage in a controlled manner. The X-ray Signal is monitored continuously by a computer interfaced to the instrument with an analog-to-digital converter. 400,000 particles of a tailings sample can be scanned in about 3 hours. Particles as small as 2 um and containing as little as 3% of a particular element can be detected.

Jan 1, 1982

By Rush Kramer

A bulk compositional chemical analysis often provides incomplete information to help the mineral processor when faced with the problem of removing troublesome contaminants in low concentrations. Michigan Tech has developed a unique approach for addressing this problem. A combination of Scanning Electron Microscopy (SEM). Energy Dispersive Spectroscopy (EDS). and image analysis was successfully used to characterize the species responsible for phosphorus contamination of less than .05 weight percent in iron ore. An automated routine acquired the chemical signature of each particle on a backscattered electron image. The few particles containing phosphorus were identified from the hundreds of particles examined. and the phosphate phases present were easily characterized.

Jan 1, 1991

By Harry Littleton, Jr. Scarber, Wanliang Sun

"The Lost Foam Casting (LFC) process is relatively immature when compared to other casting processes. To make the process more robust, computer modeling is needed to reduce lead times and casting defects. In this study, metal filling of lost foam aluminum castings was visualized using state-of-art real time X-Ray technology. Metal filling of the lost foam casting was simulated using a commercial software package. The result of the computer simulation was compared with the results of the real time X-Ray visualization. Some of the computer simulation results agreed with the real time X-Ray visualization, but some did not. Based on other studies using real time X-Ray technology, new input variables, such as foam density variations, were developed for the computer modeling. With the new variables, modeling of the lost foam casting process becomes more realistic. IntroductionMold filling of the Lost Foam Casting (LFC) process is an important step toward making a quality part. In the LFC process, molten metal is poured against a refractory coated foam pattern surrounded by dry sand. At the pouring temperature of aluminum, the foam pattern is decomposed into 30% (wt) gaseous and 70% (wt) liquid foam pyrolysis products. Existence of the gaseous foam decomposition products significantly increases the back pressure on the metal stream compared with the conventional open cavity sand mold. Entrapment of the liquid pyrolysis products during the metal filling generates many casting defects, such as internal pores, fold and blisters. Existence of these casting defects sometimes seriously degrades the quality of the components manufactured by the LFC process. Understanding and controlling the metal filling of the LFC process will certainly make this process more robust."

Jan 1, 2004

By Keiji Okumura, Hong Lan, Masamichi Sano

"Magnesium has been well known as one of the excellent agent of desulfurization, deoxidation, etc. in iron- and steelmaking because of its high reactivity. Since its production is energy nitensive, the price is very high. Thus magnesium has not widely been used as an agent in metal refining ·processes. In the present work, reduction of magnesia by carbon and aluminum is examined. Because the reaction is very sensitive to temperature, non-isothermal technique is applied to investigate the reaction kinetics. The effects of heating rate .and reaction interface area on the reaction kinetics .are studied. .A kinetic model is proposed based on the experimental results.IntroductionFor the metal refining processes, the production of high purity metal has been one of the most important research subject. In order to produce the high purity metal, the amount of the refining agent and the consumed energy is increasing. Therefore, if the future earth environment is taken into consideration, the further efficient and energy saving processes are required. Generally, Cao slag has mainly been used for desulfurization of molten iron as a desulfurization agent. However, environmental problems, such as recycling of disposal slags, are still unsolved. On the other hand, the deoxidation of molten steel is mainly performed by addition of aluminum. Therefore, the alumina inclusions· remain in. molten steel and the great efforts have been made to the removal of the inclusions. The affinity of magnesium with sulfur and oxygen is strong, and magnesium is well known as a powerful desulfurization and deoxidation agent. However, magnesium has been seldom used for the steel' refining process. The following reasons are considered. Generally, magnesium is expensive. And at iron- and steelmaking temperatures, the refining efficiency becomes low due to its abruptly .evaporation."

Jan 1, 2000

By Nozomu Hasegawa

The phase diagrams and microstructures of the slags in the Mitsubishi Continuous Copper Smelting and Converting Process were studied for the prevention of the magnetite troubles such as accretion build-up on furnace hearths and launders, blockages at the melt outlet, slag viscosity increases and so on. According to the results of those studies, the silica and lime contents in the silicate slag at the smelting furnace, and the lime content in the lime-ferrite slag at the converting furnace were changed, resulting in lower and more consistent copper levels in the discard slag, with much less need for operators to clean melt outlets and launders. However, these changes may decrease the desirable amount of accretion-coating inside the furnaces and thereby reduce furnace campaign lives. Therefore, a method of estimating the magnetite level in the melts was developed, and slag compositions and temperatures have been controlled within the appropriate ranges to prolong furnace lives and also prevent magnetite troubles.

Jan 1, 2003

By M. Rubinstein, N. C. Koon, B. N. Das, V. G. Harris

"Copper and gold - based alloys having giant magnetoresistance properties were produced by melt spinning from arc melted and cast rods. The ribbon width varied between 1 and 2 mm and the ribbon thicknesses were in the range of 30 to 50 11m. The uniform microstructure of the cast rods indicated the composition homogeneity in the starting material. The ribbons showed composition uniformity across the cross section from EDX analysis. However, the spun ribbon microstructure changed from a 'frozen in' region near the wheel side to a nanosize spherically precipitated phase towards the freely frozen surface. The evolution of the microstructure from the spun ribbon state to the annealed ones was studied by optical microscopy, SEM and TEM. The structural information of the spun and annealed specimens was obtained from X - ray, electron diffraction, electron microscopy and ferromagnetic resonance. Magnetoresistance was measured by the four point probe method.IntroductionRecently. Giant Magnetoresistance. GMR. has been observed in sputtered thin films alloys of Ag. Au and Cu with Co and Fe [1. 2. 3]. The sputtered films are produced by condensation of the alloys from the vapor phase. These Ag. Au and Cu alloys are miscible and homogeneous in the vapor and liquid phase (except Ag alloys which exhibit phase separation even in the liquid phase) but immiscible and heterogeneous in the solid phase. In our work we have produced thin ribbons of the Cu and Au alloys about 30 µm thick from the miscible state in liquid phase by rapid solidification melt spinning. The microstructural development of the ribbons was investigated in the as - spun condition and on annealing. The other properties such as magnetization. GMR and Mossbauer Spectroscopy were also investigated in the various microstructural conditions of the ribbons."

Jan 1, 1994

By R. J. Mitchell

Results from investigations into impurity distributions over cathodes are presented with implications for various sampling methods, Selection of an optimum treatment procedure for the test sample is outlined. The impact of both these studies on the development of an in-house method for sampling Isa Process cathode is discussed. The economic compromise actually undertaken, satifying wants and needs to sustain confidence in high grade cathode purity is detailed.

Jan 1, 1987

By Brommerm Tracey, Britt Elin Gihleengen, Elsa Olivetti, Hans Ole Riddervold, Randolph Kirchain, Geir Øyen

"Compositional uncertainty in secondary materials and variable processing conditions inhibits secondary material utilization in the production of aluminum alloys. Efforts to implement optimization models that direct batch planning have limited industrial presence due to factors such as the insensitivity of these optimization models to dynamic plant circumstances. This paper describes a chance constrained model formulation that generates lower cost, robust batch plans with significant flexibility towards changes in processing conditions. The principal attribute of the chance constrained formulation is its inherent mitigation of risk by diversifying the batch plan. This paper compares aluminum remelter batch planning using the chance constrained formulation with a traditional deterministic model and a manual batch planner. With the expectation that volatile material prices, restricted scrap material availability, and pressure by consumers and legislation for increased recycled raw material input will continue in the future, batch planning tools that inherently diversify a production portfolio will become increasingly advantageous for industrial aluminum remelters.IntroductionAluminum remelters must develop strategies to incorporate lower cost secondary materials into finished alloys to remain competitive amidst increasingly demanding market and regulatory conditions. Determining the optimal combination of incoming raw materials to produce an alloy that meets compositional specifications presents remelters with a complex problem that has driven the development of computational tools commonly referred to as batch planning or blending algorithms. The ubiquity of the ingredient or raw material blending problem in production has motivated ongoing development of batch planning algorithms since the classic nut-mix problem in the 1950's [1]. The most common model formulation for industrial aluminum remelters are deterministic, linear optimization programs [2]. These blending problems determine the optimal combination of raw materials by minimizing cost subject to constraints around demand, availability, and compositional specification. Despite extensive research and moderate computational requirements, batch planning algorithms are inconsistently used in industry. Insufficient incorporation of the complexity of real world remelting conditions into these models provides an obstacle for their implementation [3]. For example, many batch planning algorithms do not explicitly incorporate the impact of compositional variation of the raw materials on overall batch cost. Additionally, they do not allow for endogenous specification of tolerance to error in batch planning, so provide little flexibility where a batch planner would like to incorporate materials of greater uncertainty. Incomplete accounting for quality variability undervalues secondary materials leading to overly conservative use [ 4, 5]."

Jan 1, 2011

By M. Jennings

In 1987, Echo Bay discovered a major silver/gold ore body at their McCoy property in Nevada, and quickly made a decision to build a 5000 tpd mill which was expanded during the design to 7500 tpd. Since the ore reserves consisted of cyanide leachable oxide as well as sulfide, the plant flow sheet involved an oxide leach, a gravity circuit, and lead sulfide and a pyrite sulfide recovery by flotation. The paper describes the process development, equipment selection, plant design and the startup of the oxide treatment.

Jan 1, 1990

By Catherine Cai

A granular sorbent, prepared by gel-coating polyethyleneimine (PEI) on high surface area silica followed by crosslinking with a low-molecular weight diepoxide, has significantly higher uranium capacity, greater salt tolerance, and faster kinetics than the commercial resin Dowex 21K. Though having lower U(VI)/Fe(III) selectivity than Dowex 21K, the gel-coated PEI affords much higher sorptions of both U(VI) and Fe(III) and also their separation by selective stripping with acid.

Jan 1, 1999

By Saskia Duyvesteyn

Small ion-exchange resin particles provide faster mass transport than conventional-sized beads. Unfortunately, high pressures are needed to pump solutions through columns containing small resin particles. It is preferable to disperse fine resins in the solution being treated. Screens have been used to separate the resin from the solution, but screens do not retain fines created by attrition of the resin particles. We have developed a separation process based on flotation, which relies on the surface characteristics of the resin, instead of size. The resin is conditioned with a surfactant before dispersing it in the solution to be treated; this increases the hydrophobicity of the resin sufficiently for froth flotation, without introducing surfactant directly into the solution. The surfactant adsorbed on the resin surface does not appear to impair the kinetics of metal ion removal. A flowsheet for an effluent treatment process is proposed; other applications are clearly possible.

Jan 1, 1998

By Animesh Jha

Univariant diagrams are constructed for the reduction of nickel and cobalt oxide and sulphide minerals. The results from the carbothermic and hydrogen reduction of sulphide minerals are compared. The importance role of lime and calcium sulphate in controlling the emission of sulphurous- gases during reduction reaction is also explained. The mechanism of carbothermic reduction of nickel sulphide is explained by examining the sulphur exchange and reduction reactions. The phase equilibrium relationships that determine the formation of multicomponent liquid are characterised. Also the governing equilibria for inert atmosphere calcination- roasting of nickel and cobalt sulphide minerals are also described for the metallization of nickel and cobalt.

Jan 1, 1993

By Stein Tore Johansen

Some ferro-silicon fumaces have heat-recovery equipment. Here, the recovery of electric energy from the off-gases can be increased by increasing the off-gas temperature. This is easily done by reducing the amount of air which usually is mixed into the off-gas to cool the gas mixture. If the off-gas becomes too hot problems with severe fouling or clogging of the gas channels? close to the fumace is observed~ The result is irregular stops to clean the off-gas channels. The paper focuses on the nature? of the clogging phenomena and some of the ways to avoid clogging. A detailed experimental study was carried out at the Elkem Thamshavn Plant. Theoretical studies were performed to understand the particle deposition, turbulent multiphase fluid flow and off gas combustion in the off-gas channels. The study has resulted in reduced clogging.

Jan 1, 1992

By John L. Watson

Many metals-based industrial processes experience limitations in their operations due to an inability to effectively separate solids and liquids where partidesizes are less than 25 microns. Steel plant sludges ,generated, from the cleaning of furnace off-gases represent a typical example of processing difficulties attributable to material characteristics, and recycling or even efficient disposal of these materials is often a major problem. The use of a magnetic field to augment the traditional mechanisms of vacuum dewatering has, been demonstrated in previous work to have significant value in separating solids and 'liquids, where the solids exhibit some magnetic character. Magnetic vacuum dewatering has been used with magnetite ores and with blast furnace sludges and magnetic fields have been incorporated successfully in drum and disk vacuum filters. The research described in this paper investigates the use of magnetic seed material and flocculants to extend the application of magnetic, vacuum filtration to non-magnetic pulps. It is shown that the addition of a flocculant can enhance the capacity of drum and disk magnetic fIlters when treating materials, such as steelmaking sludges, which are only partially magnetic. In addition, the use of seed magnetite with a flocculant is shown to improve the dewatering of fine hematite pulps in a drum magnetic filter. However the use of a flocculant and seed magnetite had only limited success in improving filtration in a disk magnetic filter with a fine quartz pulp. A disadvantage of magnetic vacuum filtration with seeding appears to bean increase in cake moisture due to water entrapment in the floes resulting from agglomeration and magnetic attraction.

Jan 1, 1999

By Wei-feng Liu

On the basis of the brief introduction of the gold-antimony concentrate smelting process in China, some problems in the original process were analyzed and the corresponding improvements were introduced in this paper, such as the treatment of antimony matte, the refinement of gold-silver alloy, the concentrating gold from gold-antimony alloy, the treatment of soda slag. The roasting method that was used to treat the antimony matte was transferred to the ore dressing method. The solvent extraction was used to refine the gold-silver alloy instead of the electrolytic method. The technology of selective chlorination leaching under controlling potential was applied to concentrate gold from the gold-antimony alloy and gold-lead alloy instead of the electrolysis method. Soda slag was recovered by the second reducing smelting method substituting for the mixed-salt method of sodium arsenate. After those improvements, the process has been done smoothly; the direct recovery rate of metals has been greatly increased. Meanwhile the procedure

Jan 1, 2008