Search Documents

By Ahmet Geveci

[Generally accepted formula related to sulfur slag-metal distribution ratio is given by the following equation: [ ] According to the above equation it can be deduced that sulfur distribution between slag and metal is governed mainly by metal composition (?s term), slag composition (slag basicity and in turn sulfide capacity), oxygen potential of the system (ao¬¬ term) and temperature(related to equilibrium constant, K). In this study, the results of ladle furnace operations conducted in Erdemir-Iron and Steel Works Co. (Turkey) in relation to sulfur removal, have been given. Typical ladle furnace slag analyses of 4937K quality steel have been presented. Activity coefficient of FetO,?FetO, have been calculated with the relation obtained fromthe literature. Activity calculations have been performed with the program written in Mathcad. The changes in activity of aFetO in the slag phase,, have also been studied in relation to the sulfur removal: The relation between % Decrease aFetO and %DeS (measured)have been investigated for 4937K runs and someother types of steel produced in the Erdemir Plant. Related to ladle operations %desulfurization defined as [(%Sinitial-%Sfinal)/S%initial]*100 values have been presented for different steel qualities.]

Jan 1, 2006

By M. Ramprecht, M. Wu, A. Kharicha, A. Ludwig, H. Holzgruber

"The influence of the frequency of AC power supply on the magneto-hydrodynamic during the electroslag remelting process is studied. The focus is on the electrodynamic field and its resulting mechanical effects on the flow and liquid interfaces. The possible influence of the electrochemistry on the droplet formation is qualitatively discussed.IntroductionThe electroslag remelting (ESR) process is a secondary melting technique which can be used for a variety of metals and alloys, provided appropriate fluxes (slags) and melting parameters are employed. The ESR process is presently operating mostly with AC current of about 50 Hz. However for reasons primarily of inductive losses in the electric circuit, furnaces for ingots larger than 1 m, use or are projected to use current of very low frequency (< 5 Hz). Effects of lower frequencies (2.5-5Hz) on macrostructure and non-metallic inclusions were recently studied by Chang [1]. Most of investigations were performed either with DC power or with AC of 50-60 Hz [2-4]."

Jan 1, 2012

By Ken Baxter

The Sepon Copper Project is located in Laos and has a mineable reserve of approximately 16Mt of ore grading 5% copper with minor gold and silver values. The deposit is a clay-hosted secondary copper mineral suite, predominantly chalcocitic in nature with associated pyrite. The current project design is based on the production of 60,000t/a of LME Grade A cathode by an acid leaching process followed by solvent extraction and electrowinning. Significant metallurgical testwork was conducted as part of the Definitive Feasibility Study (DFS) with process challenges identified and overcome at each phase of testing. Flowsheet configuration is geared to autogenously generating sufficient acid and ferric iron to meet gangue acid consumption and to leach the copper. The ability to maintain acid and ferric levels in the process liquors is strongly influenced by the proportion of pyrite in the ore presented to the autoclave. This paper will outline flowsheet development from preliminary variability testing to pilot plant and DFS design. The Sepon process solution seeks a balance between operability and capital/operating costs, and provides insights into the basic mechanisms influencing flowsheet selection for these ore types.

Jan 1, 2003

By Katsunori Yamaguchi

The zinc, lead and alumina contents in copper smelting slag are increasing with the increase in waste recycling. The recovery of base metals such as lead and zinc from copper converter slag is important from both an economical and environmental perspective. As a fundamental study of the metal recovery by reduction process, activity coefficients of ZnO and PbO in the CaO-SiO2-FeOx-5mass%AlO1.5 slag under iron saturation at 1573K are derived from the data of slag-metal equilibrium experiments. On the basis of the obtained data, the activity coefficients of ZnO and PbO in the CaO-SiO2-FeOx-5mass%AlO1.5 slag were compared with those of the CaO-SiO2-FeOx ternary system. Addition of alumina increases activities coefficient of ZnO and PbO in SiO2 rich side of the slag, and decreases them in CaO rich side.

Jan 1, 2006

By Roald Ysteboe, Finn Olesen

"Elkem has developed a process that utilizes SPL as a raw material for pig iron production. This process will be demonstrated in industrial scale during 2008 and 2009. The process developed produce iron, and the reduction material used, is the carbon present in the SPL. The iron source could be either virgin iron ore or waste/recycled material from the steel industry. The SPLrefractory and bath material is dissolved in the slag produced. The slag is designed so that any leaching of environmentally dangerous elements is minimized. This process can in addition to SPL, consume other types of waste derived from the primary production of aluminium. Elkem intends to supply this demo project with SPL and other waste products from external sources, domestic as well as international ones.IntroductionSpent Pot Lining (SPL) is generated when an electrolytic cell for producing aluminium is taken out of service and the refractory and carbon lining is removed from the steel potshell.The yearly generation of SPL world wide is exceeding 500 000 tonnes. The major amount of this quantity is stockpiled or land filled, unprocessed.SPL contain large amount of water soluble fluorides and some amount of cyanides and is classified as hazardous waste in most countries."

Jan 1, 2008

By Toshihide Takenaka

Improvement of corrosion resistance of Mg metal by addition of rare earth metal (RE) was studied, and the effect of surface oxide layer with RE was investigated. The corrosion resistance of Mg was remarkably improved by adding a small amount of RE, and the suitable RE content was clarified. The corrosion resistance of Mg was particularly bettered by conversion coating using a solution including both RE(NO3)3 and Mg(NO3)2. This result indicates that the surface oxide layer consisting of both Mg and RE gives good corrosion resistance to Mg metal. In this study, direct electrodeposition of Mg metal containing RE was also tried in molten chloride with RE chloride, and it was shown that electrolysis could be performed stably. The RE content in the deposited Mg metal was depended on the concentration of RE chloride in the bath and the cathode potential, and Mg metal containing the suitable RE content for its corrosion protection was obtained easily by direct electrolysis.

Jan 1, 2006

By Johannes Boonstra

High rate bacterial catalyzed processes can serve to improve hydrometallurgical operations. These solutions are not only economical but also environmental sustainable. With references around the globe, the value of this new approach is recognized by industry worldwide. For instance, metals can safely and economically be separated from process and waste streams using biotechnologically produced sulfide, recovering a valuable metal sulfide product instead of a waste gypsum stream for disposal. Both the natural biological sulfur and nitrogen cycles offer bioconversions that are applied on industrial scale. The shared advantage of these processes is that waste compounds are converted in either a reusable raw material or in a harmless product. This way, natural product cycles can be closed. Applications based upon bioconversions are for example: Sulfur based: Bioleaching, reduction of oxidized sulfur compounds to elemental sulfur, metal recovery with biogenic produced H2S, SO2removal from gas streams, etc. Nitrogen based: Ammonia removal using the anammox-process, biological removal of NOxfrom gas streams, nitrate removal from water streams, etc. Metals: Bacterial processes for the reduction of metals such as uranium, selenium and manganese have proven to offer great potential for clean-up of groundwater streams. This paper contains a description of the above applications. Further, a short introduction on engineered high rate bioreactor systems and a description of industrial biotechnological applications will be provided.

Jan 1, 2003

By H. L. Ludtke

Microlaminate composites were fabricated by electron-beam physical vapor deposition. The microlaminates consisted of five layers, each 2 to 4 pm thick, and were composed of either pure metal layers (Cu-Ag), or alternated between metal and intermetallic layers (Nb(Al)- Nb3Al). The microlaminates were heat treated in an Ar atmosphere for 2 to 12 hours, at temperatures of 600°C for the Cu-Ag and 1000°C to 1200°C for the Nb(Al)-NbsAl. Microlaminates were examined after deposition and after heat treatment by scanning electron microscopy and energy dispersive x-ray spectrometry. The effects of heat treatment on the morphological stability of these composites will be described.

Jan 1, 1999

By Mao Chen, Tim Evans, Zhixing Zhao, Weidong Zhang, Baojun Zhao, Dongqing Wang

High temperature softening behaviours of iron blast furnace feeds (sinter, lump and pellet) have been determined under conditions simulated to the blast furnace. The industrial samples were packed with sandwich structure (coke / ore / coke) in graphite crucibles and 30 CO / 70 Ar gas mixture was blowing directly through the bottom of the crucibles. The displacement and temperature were continuously recorded simultaneously to construct the softening curves. Separated quenching experiments were also carried out at selected temperatures under the same gas atmosphere. The temperatures were selected corresponding to the turning points of the softening curves. The phase assemblages and composition of each phase in quenched samples were analysed by Electron Probe X-ray Microanalysis (EPMA). The proportion of the liquid formed at temperature was obtained from the backscattered electron images. The deformation characteristics of these complex multi-phase materials are shown to be related directly to the phase assemblages of the samples and the microstructures. FactSage was also used to assist the predictions of liquid / solid fractions and their compositions.

Jan 1, 2015

By Nobuaki Sato, Tetsuo Fukasawa, Akira Kirishima

To apply the fluoride volatility process for the treatment of fuel debris formed in the damaged nuclear reactors, study on the fluorination behavior of main constituents, such as fuel and cladding is essential. The mixture of uranium and zirconium oxides is formed under severe conditions such as high temperature and oxidizing atmospheres. In this paper, fluorination and volatilization behavior of uranium and zirconium oxides have been studied by TG-DTA method in the presence of fluorine. From the TG-DTA result of UO2 in F2 atmosphere, the weight gradually increased up to 7% at 350 oC followed by rapid weight decrease with exothermic peak showing the vaporization of uranium as UF6. ZrO2 showed similar fluorination behavior to that of UO2. However, fluorination of UO2-ZrO2 seemed to be suppressed with increasing ZrO2 amount. This may be caused by the formation of solid solution.

Jan 1, 2016

By Toshiaki Nakai, Kunihiko Takeda, Kimio Imaizumi, Hiroaki Shirasaka

"The new type of nano-porous silica particle was considered to be constructed by the spinodal decomposition-type process which was found to have narrower pores than those of conventional porous silica prepared from boron silicate or ""Shirasu"" balloon. Nano-porous silica particles were fabricated by the calcination of silica gel mixed with well-dispersed complex salts composed of phosphorous and molybdenum compounds. Both silica and inorganic salts were not perfectly dissolved in the suspension solution. After removing of the water, the silica-inorganic salts complex was volatized and successively calcinated at a temperature ranging from 650 °C to 800 °C. Then, the inorganic salts were removed by dissolving in hot water. Other inorganic salts such as potassium halides were also found to be effective as a pore-size controller.IntroductionControl of structure has an important role in the field of industry as well as in the separation and purification technology for metals and organic syntheses. Many studies on the control of material structures have been reported regarding porous materials with pores ranging from nanometer to micrometer scale. 1 ) One example is zeolite as a naturally yielded porous inorganic material. Various types of synthetic zeolites have been studied as ""molecular sieve"" materials with ordinary pore-size of less than one nanometer. In 1992, crystalline meso-porous material with a large surface area named MCM-41 was synthesized through the use of template synthesis. 2) In direct relation to our study, amorphous borate glass having 4 to 100 nm of fine pores known as Corning glass 3l or SiO2-Al2OrB2O 3-CaO porous glass having large pore dispersity ranging from 4 to 10,000 nm have been reported. 4 ) S) 6 ) Some examples of several reported studies are as follows: phase-separated porous glass consisting of B2OrAl2O3-ZrO2-RO-R2O complex oxide 7 ) glass with finer pore induced from hydrolysis of silane alkoxide, porous material attained by condensation polymerization through the use of sol-gel process 8), alumina meso-porous material 9 ) 10), silica-zirconia material 11), carbon porous material 12), etc.."

Jan 1, 2000

By Pradeep kumar Jha, Manas Mohan Mahapatra, Sabin Kumar Mishra, Satish Kumar Ajmani, Satish C. Sharma

"Due to mechanical/ electrical failure in the C.C. line or inadequate availability of molten steel from coming ladle, sometimes one/two outlets of a multi-strand tundish in continuous casting unit is closed. Closing any of the outlets affects the flow distribution inside the tundish which in turn governs the quality of steel coming out. Hence it is important to study which of the outlets should be closed to have proper results in terms of flow behavior and inclusion removal inside the tundish. Present study aims at finding the effect of closing one or two outlets on flow behavior and inclusion removal in a multi strand tundish. It was found that closing the near outlet (outlet near to the inlet) increases the inclusion removal tendency than closing the other two outlets in a six-strand billet caster tundish (only three outlets are considered because of symmetry).IntroductionContinuous casting process transforms molten metal into solid on a continuous basis. This process is the most efficient way to solidify large volumes of metal into simple shapes for subsequent processing [1]. Molten metal is tapped into the ladle from furnaces. From the ladle, the hot metal is transferred via a refractory shroud (pipe) to a holding bath called a tundish. The tundish allows a reservoir of metal to feed the casting machine while ladles are switched, thus acting as a buffer of hot metal as well as smoothing out flow, regulating metal feed to the moulds and cleaning the metal [2]."

Jan 1, 2012

By Sang-Su Lee

This paper shows the application of the porous plug system in the Mitsubishi continuous copper smelting and converting process. This system has already been adopted and utilized in the steel industry to enhance productivity. Recently, some copper smelters have adopted this system but the results have not been satisfactory. The porous plug system was installed at the anode furnace in December 2001 to reduce the oxidation time and decrease the oil consumption. A good effect was that the nitrogen stirring of the melt through porous plugs improved the melt heat transfer. As the result of the enhancing heat transfer the oil consumption and the build up inside the furnace were actually decreased. But until now the oxidation time has not been sufficiently reduced. In the future, further research and tests are needed in order to increase the productivity and save costs.

Jan 1, 2003

By Kampe. S. L., Baker. Andrew H., Tony Zahrah

"Experimental heats of reaction for the formation of several Al3Ti + TiB2 intermetallic composite formulations have been determined utilizing bomb calorimetry. To overcome the kinetic constraints and achieve ignition in these formulations, a boron (B)/potassium nitrate (KNO3) initiation aid was incorporated within the blended reactant compact. The heat contribution from the initiation aid was regressed to provide estimates of the heat of reaction of the nominal formulations. Powder x-ray diffraction was utilized to identify the products of the reaction and discern any differences between the predicted equilibrium products of the formulation and the actual products.IntroductionReaction synthesis is a technique for the creation of ceramics, intermetallics, and in-situ composite materials [1]. Reaction synthesis is defined by its self, propagating mechanism, where the energy liberated from a localized reaction within a green powder compact is enough to carry the bulk reaction to completion. Achieving a self, propagating state can be achieved in variations of two primary methods of initiation: uniform volumetric heating and directional propagation [2].Uniform volumetric heating involves subjecting a green compact of the unreacted formulation to uniform heating in a furnace to encourage diffusion to initiate the reaction (Figure 1a) throughout the bulk material. Directional propagation utilizes a point heat source at one section of a green compact of unreacted formulation (Figure 1b). The localized exothermic reaction at one point in the compact then initiates the reaction in the section of the compact adjacent to it and fully propagates throughout the entire compact until completion. Initiation of the localized reaction is generally associated with the melting of the constituent with the lowest melting point, with instantaneous initiation of the reaction usually occurring close to that melting point [1]. This melting point can be high in some systems of interest, such as the titanium (Ti) and boron (B) system in equation 1:"

Jan 1, 2011

By M. K. Yelloji Roa

Effect of conditioning with Thiobacillus ferrooxidans on the floatability of sphaierite and galena has been determined in this work. The flotation behavior of the conditioned minerals clearly shows that such bacterial conditioning does produce marked modification of their surfaces. The variables affecting the surface modification and thereby the flotation response of the minerals were found to be cell concentration used for bacterial conditioning, the period of biotreatment and the pulp density. Importantly, while the enhancement in flotation obtained due to sulphuric acid treatment was retarded by biotreatment in the case of galena at all cell concentrations due to electrochemical effects, such decrease occurred in the case of sphalerite only at cell concentration sufficiently high for their attachment to the mineral surface. The effect of bacterial conditioning has significant implications to the differential flotation of sphalerite and galena. Mechanisms responsible for the modification of the surface properties of these sulphides due, to bacterial conditioning are discussed.

Jan 1, 1991

By Jhon Cuya

Titanium dioxide is the well-known catalyst for the photodecomposition of water in UV region and its nanoparticles show better performance than its bulk materials. Furthermore, partially sulfurized TiO2 is expected to be chemically stable and have an enhanced photocatalytic activity compared with TiO2. For this purpose, the sulfurization behavior of TiO2 nanoparticles was thermogravimetically (TG) studied by a thermo-balance with a quartz spring using CS2. From the TG curve of TiO2 nanoparticles, first, the weight decrease appeared down to around 8 wt% and then sulfurization reaction started at around 500 °C at heating rate of 1O &apos;Cumin. The weight increase curve showed a maximum of ca 30 wt% at around 750 T and then gradually decreased to ca 12w% at 1000OC. This would be caused by the formation of TiS2 followed by the decomposition of TiS2 to lower sulfides, such as Til.08S2 and Ti3S4. From the comparison of the sulfurization of TiO2 nanpparticles with that of anatase, rutile and Ti(OH)4, it was found that TiO2 nanoparticles showed a similar behavior to that of Ti(OH)4.

Jan 1, 2003

By Carlos A. Nogueira

Spent Ni-Cd batteries contain in the electrode materials heavy metals like Ni, Cd and Co, which must be recycled due to environmental problems. Pyrometallurgy is normally used for recycling these end-of-life products, but alternative processes by hydrometallurgy, integrating also physical operations, can be used. Hydrometallurgy seems to be useful, because metals can be efficiently recuperated in chemical forms with commercial value. The economical viability of this recycling process can be improved increasing the treatment capacity, through the application to different types of residues with similar characteristics like Ni-MH and domestic batteries, or other residues containing Ni/Co, like sludges, dusts or spent catalysts. Spent Ni-Cd batteries were first physically processed using shredding and wet sieving operations. Best results were achieved using an output of 6 mm in the shredder and 1.4-2 mm in the physical separation by wet sieving, resulting a fine fraction containing 70% of the initial electrode material and only 6% of the initial scrap. The acid leaching of the obtained material in the previous operation was studied, being the parameters like: temperature, H2SO4 concentration and the liquid/solid ratio (L/S) optimized. The values attributed to the factors which concerned the best results obtained on the leaching process were mainly influenced by Ni recovery. In opposition, Co and Cd were easily leached in a wide range of conditions. To attain an overall recovery, with minimum costs, of the three metals, the values of T~100ºC, [H2SO4]=2.3-2.7 M and L/S=8-10 L/kg were considered the most appropriate.

Jan 1, 2006

By Dai Xi

In the present work, the viscosities of molten FenO-MgO-SiO2 and FenO-MgO-CaO-SiO2 semi-synthetic slags for nickel flash smelting were measured in the temperature range from 1473 to 1723K by a rotational viscometer. The ratio of Fe to Si02 was fixed at 1.2, calcium and magnesium oxide contents varied in the range from 2 to 8 mass% and 9 to 12 mass%, respectively. The results showed that silicate anions became smaller by increasing CaO content, which results in a decrease of the viscosity of the slag. In the case of MgO addition the viscosity behavior was complicated. At MgO content below II mass%, the viscosity increased with the increase of MgO at all temperatures tested. However, when the MgO content was above II mass%, the viscosity decreased slightly for FenO-MgO-CaO-SiO2 system. At higher MgO contents, low-viscosity slags can be obtained by adding CaO. At a given composition, .the viscosity decreased with increasing temperature. The higher the temperature, the more MgO can be added before saturation. The effect of Fe3O4 on the viscosity was quite significant. The viscosity of slag increased by 300mPa-s at 1573K when Fe3O4 content varied from 3 to 9 mass%. The viscosity values are presented as the functions of temperature and composition. A comparison between FenO-MgO-SiO2 and FenO-MgO-CaO-SiO2 systems is given in this study.

Jan 1, 2003

By Veneta Groudeva

A pyritic ore containing zinc, lead and copper as? the relevant primary sulfide minerals, .as well as gold and silver finely disseminated in the sulfide matrix, was? leached in percolation columns. Each column contained 30 kg of ore crushed to minus 10 mm. Firstly, zinc and copper were efficiently leached by means of chemolithothrophic bacteria? in acidic sulfate bearing medium. Zinc was leached more rapidly than copper but the final extractions of these metals were similar (about 75% in 300 days). A part of the galena was oxidized to the. insoluble lead sulfate during the leaching. The pyr:ite was, however, relatively slightly attacked. The ore was then leached by means of FeC11 - HCl solutions both in the presence and in the absence of bacteria to solubilize the lead. The chemolithotrophic bacteria grew in media containing both chloride and sulfat~ ions and maintained a high ferric to ferrous ion ratio in the percoiating solutions. The chemical leaching was, however, more efficient since ft was possible to carry it out at higher chloride ion concentrations. About 10% of the lead was leached in this way in 90 days. Finally, the ore was leached by thiourea in the presence of a gold-oxidant (oxone) to extract the gold and silver. Over 60% of the gold and over 55% of the silver were extracted from the ore in 150 days, while. the extractions of these precious metals from an untreated ore sample were lower than 25%.

Jan 1, 1991

By M. Cowling, S. Kumarl, A. W. Piper, R. A. Forsdick, C. Bailei, M. Patell

"The lead-refining process takes place in hemispherical vessels called kettles. In these kettles, lead-bullion is mixed at a certain temperature to remove impurities from the melt. This paper presents steps in a novel method for calculating vortex shape and flow field in the refining kettle using Computational Fluid Dynamics (CFD). First of all a two-dimensional axisymmetric model is used to calculate the vortex shape at the liquid-air interface. Here action of impellers and baffles are accounted for by adding source and sink terms to the appropriate momentum equations. The model includes Yolume of Fluid (YOF) method to predict the shape of interface deformation, i.e. vortex. This strategy reduces the computationally intensive three-dimensional transient simulations to a more efficient two-dimensional model. The calculated vortex shape is then used to regenerate a full three-dimensional grid. This grid is used to carry out steady-state simulation using the standard multiple-reference-frame method of impeller-fluid-baffle interaction within the commercial code Fluent. Simulation results for both stages of the development are compared with experimental data.IntroductionOne of the most important steps in Lead Refining process is impeller stirred mixing of Lead Bullion in hemispherical vessels. During this process, the melt is treated with one or more reagents in order to remove impurity elements such as copper, antimony, silver and bismuth. These impurities react selectively with the reagents and float to the melt surface in the form of a powdery layer, which is then skimmed for further processing. Figure-! shows (a) the lead refining kettle and (b) the schematic representation of involved flow pattern. Stirring of the lead bath using specific impeller designs, which creates a central vortex, provides a mechanism for draw-down and dispersion of the buoyant reactants. Clearly, effective control of the impeller generated vortex and flow pattern is crucial to achieving efficient operating conditions."

Jan 1, 2001