Search Documents

By Sang-Joon Kim, Hae-Geon Lee, Hyun-Jin Cho

"Decarburization phenomena on the surface of liquid iron have been simulated by numerical method and the results were compared to the experimental data. During the DeC process in a converter, a large amount of splashed droplets are generated from the top surface of the bath and consequently the reaction surface area is increasing tremendously. Since the decarburization mainly occurs at the interface, it is important to understand the reactions on the liquid iron droplets. The flow and species concentration fields around liquid droplets taking into account the reaction of carbon with oxygen at the interface were calculated by a commercial CFD code FLUENT which solving multiphase Navier-Stokes equation with Volume Of Fluid method, species transport equations and energy transport equation. The initial carbon concentration was fixed to 4 wt% and the concentrations of oxygen in the atmosphere were varied from 5 to 50 wt%. As comparing the numerical calculation with experimental data written in the reference, the results have a good agreement for decarburization rate.IntroductionIn a primary steelmaking process, one of the main functions is to decarburize from hot metal and the 4% of carbon is decreased to about 0.5% of carbon. Even though there are some possible reactions leading to the removal of carbon from hot metal, the main reaction occurs on the free surface by direct oxidation of carbon at the gas-liquid interface with producing the carbon monoxide gas. In many metallurgical processes involving a jet impinging onto a steel bath surface, especially in a Basic Oxygen Furnace (BOF) converter, it is important to understand the behavior of molten iron droplets splashing out of the steel. The iron droplets are generated by an oxygen or air jet blowing and it increases the total surface area of liquid iron tremendously. Since the decarburization reaction is mainly affected by the surface area, it is necessary to verify the decarburization phenomena around the splashed droplets from liquid iron in order to allow an analysis ofBOF process possible."

Jan 1, 2011

By Mikio Kobayashi

Extraction of valuable metals from sulfide ores continues to be a very important, process and so the strict control of discharge of harmful metals in effluents from refineries becomes more important in the future. The recovery methods for heavy metals have been developed. Some metals such as Se and As are still difficult to be removed to very low concentration, although the techniques for recovery and removal for many kinds of heavy metals have already been developed. Especially, in case of Se the recovery system from water with low concentration has not be developed yet, although the WHO decided Se to be harmful for human beings and then the discharge control is under obligation now. In general Se exists as selenite ion and/or selenate ion in aqueous phase and selenite ion is able to be recovered by coprecipitation with ferric hydroxide or by reduction to solid selenium by general reductants. Selenate ion, however, has a strong resistance to conventional treatments. Therefore the new technique for the recovery of Se from water including selenate ion has to be developed. In this presentation the new approach for removal of selenate ion using the reaction in which ferrous ion is oxidized to ferric ion is presented. Selenate ion is reduced to selenite ion during the reaction and then to solid selenium, while ferrous ion is oxidized to ferric ion. The coexistence of activated carbon is very useful to increase the reaction rate. The use of iron powder is also effective and very useful for reducing gel-like precipitates mainly consisted of ferric hydroxide. The concentration of the residual selenate ion is probably under 0.1 ppm after recovering Se by the mentioned-above approach. In addition to the mechanisms of these reactions, the effects of pH, coexistent positive and negative ions, and reaction temperature are also presented. Furthermore the investigation of the behavior of selenosulfate is presented.

Jan 1, 1998

By Cindy L. Williams

"The Blue Star subdistrict in the Carlin Trend, Nevada, includes multiple mines with 33.9 t Au in reserve and past production totaling 89 .1 t Au. The deposits are characterized by zoned alteration mineralogy and gold grades. From orebody centers outward the zones include: 1) a silicified core with erratic gold grade; 2) adjacent mill-grade (> 1.37 Au git) intense quartz-sericite-pyrite alteration; 3) enveloping leach-grade (0.21 Au g/t to 1.37 Au git) weaker sericite-kaolinite-quartzpyrite alteration; 4) surrounding decarbonatized and intensely argillized waste and leach grade ore; 5) pervasively decarbonatized waste rock; and 6) peripheral waste with weak decarbonatization and local propylitic alteration. Zoned alteration extends as much as 1500 m beyond orebodies.Understanding Blue Star subdistrict zoned alteration assemblages and gold grades has increased geologists' ability to provide practical and economically significant information to geotechnical engineers, mine planners and drill and blast personnel. Alteration influences geotechnical pitslope design because each assemblage has distinct rock strength. Geotechnical engineers use three-dimensional models of incompetent alteration types as a foundation for pit-slope design. In the drill and blast cycle, hard and soft alteration types require modified practices (powder column, blast hole spacing, delay design etc.) for optimum blast energy distribution. Further, geotechnically instable alteration types require careful blast procedures to prevent backbreak whic~ damages ultimate walls. In addition to mine planning and mining applications, zoned alteration assemblages extending beyond orebodies provide a useful exploration guide. Metallurgical character also varies with alteration type. Intensely quartz-sericite-pyrite altered or silicified ore has relatively high partical-size dependency and poor leach recoveries. Moderately sericite-kaolinite-quartz-pyrite altered rock, in contrast, shows little size dependency and good leach recoveries.The author sincerely thanks L. Schutz, P. Williams, C. Clode, W. Trudell, P. Herrera, M.DKunkel, M. Goings and numerous other Newmont geologists, metallurgist, engineers and support staff who made this paper possible."

Jan 1, 1997

By D. Norman, D. J. Hughes, R. Dashwood, I. McGregor, N. D. Raath

"This paper develops a methodology for predicting spot weld fractures in automotive boron steel grades, such that fracture modes can be predicted accurately in a vehicle or sub-assembly structure. To achieve this, it was necessary to understand the range of complex fracture modes observed in boron steel spot welds and how these are linked to the Heat Affected Zone (HAZ) microstructures and hardness distributions and residual stress.Material data for the HAZ was extracted by simulating the spot welding process using a Gleeble machine; achieving specific weld microstructure in a larger volume which was used in destructive testing. Neutron diffraction was employed to accurately characterize the post-weld residual stresses found inside the weld. The constitutive relations of specific areas in the HAZ where fracture is thought to occur is being incorporated into finite element software to improve fracture prediction of boron steel welds.IntroductionWith the drive for light-weighting and improving passenger safety, lighter and stronger materials are being continuously sought in the automotive industry. The application of boron steel in the Body-In-White (BIW) meets both these criteria by down-gauging thickness of the steel and increasing the strength. As an example, when applied to crash-relevant areas in cars, components have an ultimate tensile strength of 1500 MPa, minimum springback and reduced sheet thickness.To achieve high strength and low springback, boron steel components must be formed and hardened at the same time. This is typically achieved by austenitizing the steel around 900 °C and simultaneously quenching and forming, usually with a hydraulic press and tool-set. Trace amounts of boron, typically 0.005wt%, increase the hardenability of the steel dramatically. This is attributed to the grain boundary segregation of boron, which hinders the formation of ferrite during cooling and forces the transformation of austenite to martensite at high cooling rates, a minimum of25 °C/s."

Jan 1, 2013

By Mala Nath, Atjit Mallick, Asheesh Kumar

"The present research work is aimed to focus on the development of chemically stable light weight microporous carbonaceous material, such as activated charcoal incorporated either with titanium n-butoxide, titanium diisopropoxide bis(2,4-pentanedionate), vanadium 2,4-pentane-dionate or zinc 2,4-pentanedionate having varying wt% of the metal (2-8%) using ethanol as solvent at 40--50 oC followed by calcinations at 100, 150 and 200 cC, except the samples with titanium diisopropoxide bis(2,4-pentanedionate) which are calcinated at 80 oC. Atomic absorption studies along with FESEM revealed that the maximum incorporation of metals (Zn, V and Ti) in activated charcoal was observed with 4 wt% of zinc 2,4-pentanedionate calcinated at 150 oC , 4 wt% of vanadium 2,4-pentanedionate at 100 oC, 2 wt% of titanium n-butoxide at 100 oC and 2 wt% of titanium diisopropoxide bis(2,4-pentanedionate) at 80 oC, and equilibration time of 20-24 h was used in each case. Hydrogen sorption behavior in these carbonaceous materials has also been studied at 77.4 K and low pressure up to I bar. The highest hydrogen uptake obtained was 1.45 wt% (164.5 cm3 (STP)/g at P/Po = 1.0) for activated charcoal incorporated with 4 wt% of zinc 2,4-pentanedionate calcinated at 150 oC.IntroductionTwo of the major challenges for humanity in the next twenty years are the shrinking availability of fossil fuels, the global warming and potential climate changes that result from their ever-increasing use. So it is necessary to fmd an energy source that is convenient, flexible and controllable. One possible solution to these problems is to use an energy carrier such as hydrogen, and ways to produce and store hydrogen in electric power plants and vehicles. Hydrogen storage is the bottleneck for the breakthrough of hydrogen as energy carrier in automotive applications [1]."

Jan 1, 2012

By Nourredine Menad, Christian Lucion, Maurice Save, Paul Hubaux, Solène Touzé

"The collection and treatment of WEEE has recently become mandatory in Europe and is now being organized. As the first step in current treatment processes is manual dismantling, we decided to investigate the development of an entirely automatic WEEE treatment procedure using physical separation techniques so as to limit manual sorting to the removal of hazardous components. Our approach was to test different wet and dry physical separation methods on bulk WEEE; i.e. gravity separation (jig and pneumatic table), electric conductivity separation (eddy currents), and particle shape separation (Lavodune classifier and vibrating helical conveyors). The results enabled us to determine a global treatment flowsheet of shredding, electromagnetic separation, eddy current separation, screening (2 mm), sink&float separation (d=1), and jigging. All the end products, except for the fine fraction, have possible recycling outlets. Batches of WEEE can thus be treated automatically once the problem of non-ferrous wires is resolved.IntroductionAccording to Ademe (French Agency for Environment and Energy Management; www.ademe.fr), France's annual production of WEEE is between 1.7 and 2.0 million tonnes. This waste, although of very varied composition, consists mainly of plastics and metals, and its collection and treatment has been mandatory in France since 2006; the modalities are gradually becoming organized. Existing treatment processes rely on a first step of manual dismantling which, though essential for removing dangerous components from the WEEE (e.g. batteries, cathode-ray tubes, ink cartridges, etc.), also includes separating out the decimetre-size plastic parts and metal parts. No fully automatic process has yet been developed for this type of waste. Moreover, the dismantling units in Europe are highly subsidized and call upon social workers. As this situation is not conceivable for the long-term, it is obviously important to develop entirely automatic WEEE-treatment technologies based on physical separation techniques. This would limit manual sorting to the removal of toxic components."

Jan 1, 2008

By Somayeh Dashti, Ehsan Vahidi, Fereshteh Rashchi

"The main goals in zinc electrowinning process are decreasing of power consumption and increasing of current efficiency. In this study, the electrowinning of zinc in the presence of different additives in electrolyte were established and Arabic Gum, Gelatine, sodium lauryl sulphate and l-hexyl-3-methylimidazolium hydrogen sulfate in the five levels using Taguchi method was examined. In our previous researches, using orthogonal array, effect of zinc electrowinning parameters such as anode type, current density, sulphuric acid concentration, temperature and zinc ion concentration was studied and the optimized conditions for zinc electrowinning was obtained. Anode composition: Pb-Ag 0.5%-Sn2%-Sb1%, current density (A/m2):500, acid concentration (g/1):165, temperature: 60°C, zinc ion concentration (g/1):70. The main goals in zinc electrowinning process are decreasing of power consumption and increasing of current efficiency. ln this research, the effect of four additives: Gum Arabic, Gelatine, sodium lauryl sulphate and an organic material in the four levels with Taguchi method was examined. ln fact the effect of electrolyte environment and determining the best electrolyte under the optimized conditions is the main aim of this study.IntroductionDue to its low cost and abundance, zinc is widely used in the production of brass, galvanized steel, sacrificed anodes and primary and secondary batteries [I]. Some 80% of world primary zinc production is derived via roast-leach-electrowinning processes [2-4]. In the electrowinning process to both improve final product quality and current efficiency the leachate should be purified [5].To produce zinc a current method is to extractit from acidic zinc sulphate solutions by electrolysis with aluminum cathodes and insoluble lead-based anodes [6]. Though the electrolytic processing of zinc has been performed for many years, there are still current efficiency problems in the cathodic process. These low efficiencies (88- 93%) have a serious impact on the costs associated with the energy consumption. On the other hand, these low efficiencies increase energy consumption and decrease the quality of the surface morphology [7- 8]."

Jan 1, 2012

By Jean Igor Margem., Lucas Barbosa de Souza Martins, Frederico Muylaert Margem, Sergio Neves Monteiro, Artur Camposo Pereira, Rômulo Leite Loiola

"The fibers extracted from the stem of the bamboo plant have been investigated as possible reinforcement composites due to their relatively high tensile strength. Although previous works have already been conducted about the mechanical properties, up to now a dimensional characterization of the distribution and the effect of diameter on the elastic modulus of bamboo fiber of the specimen dendrocalmus giganteus has not been performed. The aim of the present work was to statistically characterize the distribution of the diameter of a lot of bamboo fibers of that specimen. Based on this characterization, diameter intervals were set and the dependence of the Elastic Modulus (E) of theses fibers with a corresponding diameter was analyzed by the Weibull Method. The results indicated an inverse dependence, in which the highest Elastic Modulus were obtained for the thinnest fibers. Moreover, it was found that a mathematical hyperbolic relationship fit well this inverse correlation between the Elastic Modulus and the bamboo fibers diameters.IntroductionBamboo is a well known grass-type plant with a hard and stiff stem or culm that can reach, in some species, more than 10 cm in cross section diameter and stand several meters height. Owing to its low density, approximately 0.9 g/cm3, bamboo culms have been used in house construction from scaffoldings to panels. As an abundant natural resource in tropical and temperate regions, specially in Asia and South America, bamboo is also a substitute for wood and plastics in furniture and lightweight parts of automobile [1,2]. The cylindrical shape of the culm is, however, a limitation for its direct use in engineering systems. Consequently, research works have been conducted on bamboo fibers stripped off from the culm as reinforcement of polymer composites. [1-12]. According to Shin et al [3] bamboo fiber-epoxy laminates can be made into specific sizes and shapes, preserving the natural microstructural properties. These fiber composites overcome the limitation of the culm's cylindrical macrostructure. As a further advantage, Shin et al [3] indicated that cracking and bioerosion caused by insect pests is prevented."

Jan 1, 2013

By Zhu Fangyi

"The article introduces the process EAF with De-P hot metal charging for Melting Stainless Steel in Baosteel stainless steel Branch. Based on the practice of production, the main effect on the Cr Loss during EAF with De-P Hot Metal Charging Melting Stainless Steel including using oxygen, the material charging and making slag are theoretically analyzed. The optimization of using oxygen can reduce the oxidation of Cr during EAF Melting Stainless Steel. The optimization of material charging, especially Si content is suitable can reduce the loss of Cr. Effective reduction can realize the lowest Cr oxide in slag. Based on the character of the process EAF with De-P hot metal charging for Melting Stainless Steel, applied the integrated control method, the Cr loss during EAF melting stainless steel decreased 43.10%. 1 INTRODUCTION EAF with De-P HM charging for melting stainless steel is a technology for stainless steel making. Practice prove that the new process can shorten tap to tap time, reduce the special power consumption, dilute the impurity element from the stainless steel scrap that is propitious to produce the high quality stainless steel, alleviate the shortage of stainless steel scrap to the production. As a new technology, the process has some technical problems and difficulties. The proportion of Cr alloy charging exceeds 20% during EAF with De-P hot metal charging melting stainless steel. As Cr alloy is difficult melting and easy oxidation, too much Cr alloy charging result in Cr loss too much and tap to tap time too long for EAF production. By applying the new technology, Baosteel stainless steel branch has increased the technology level and economy index. Now the content of Cr oxide in slag reduce from 8.59% to less than 6.0%. The Cr loss during EAF melting stainless steel decreased 43.10%. According to the practice application, the process of EAF with De-P HM melting stainless steel are theoretically analyzed. The main factors affecting the Cr loss during EAF with De-P hot metal charging melting stainless steel are discussed."

Jan 1, 2008

By E. O. Stensholt

The Hybinette electrorefining process for production of cathode nickel was in use at Falconbridge Nikkelverk A/S, Norway, until 1975 when conversion to the new chlorine leach process was started. In 1978 the conversion to electrowinning had been completed, but further major improvements to the process have been made up to 1987. After a major expansion program in 1985 - 87 the refinery has a nickel capacity of 54 000 mt Ni/year. The main feed materials to the process are converter matte from the Falconbridge smelter in Sudbury, Ontario, Canada, and from the BCL smelter in Selebi-Phikwe, Botswana. A typical composition of the mixed feed to the refinery is: 40 - 45% Ni, 25 - 30% Cu, 20 - 22% S, 2 - 3% Fe and 1.0 - 1.5% Co. The matte is chlorine-leached in the first process step, nickel being dissolved selectively in a train of leach-cementation tanks. Essentially all copper and sulphur that was present in matte appears in the leach residue as CuS. In 1986 an autoclave treatment stage was added to the process to improve nickel extraction from the leach residue. The resulting strong nickel chloride solution is purified by the process steps (1) precipitation of iron and arsenic, (2) solvent extraction of cobalt and other minor elements and (3) precipitation of lead and the remaining impurities. The nickel solution is then fed to the tankhouse, where various nickel products are produced by electrowinning. The chlorine gas that is produced during the electrolysis is returned directly to the chlorine leaching tanks to dissolve more matte. After stripping from the loaded organic phase and solution purification cobalt is also produced by electrowinning. The copper sulphide leach residue, which contains some nickel, is dead- roasted in fluidized-bed roasters. The sulphur is recovered and sold as sulphuric acid. The calcine is leached in spent copper electrolyte, from which cathode copper is produced by electrowinning. Precious metals and the remaining base metals are recovered from the copper leach residue. The Falconbridge chlorine process is very versatile. It can accept a wide range of impurities in the feed and still produce metals of exceptional purity.

Jan 1, 1988

By Ying Mao, Zhancheng Guo, Long Ma, Huiqing Tang

"A new 2D computational fluid dynamic (CFD) model was developed for the gaseous reduction of iron ore fines in an innovative reactor-multilayer moving-fluidized bed. The solution of the proposed model was performed by integration of FLUENT and PHOENICS. Numerical results of cold state were compared with the experimental data and the agreement between them was good. A hot case-gaseous reduction of iron ore fines using syngas with this reactor was simulated using the present CFD mode. Results indicate that under the given simulation conditions, total pressure drop is 90 Pa less than that under cold state though the gas supply rate is increased about 4m3 under hot state. Gas temperature decreases from 1073 K at the bottom to 500 K at the top, Utilization efficiency of the gas reduction potential is about 27 %. For ore fines reduction, the final reduction fraction could reach 0. 70 and solid temperature 900 K.IntroductionWith the development of coal gasification technology, various coals could be converted to Syngas with air or steam. Therefore gaseous reduction of iron ore fmes becomes an acceptable alternative process for iron making besides blast furnace route[!] and moreover it still has some advantages in processing low grade iron ore fines[2]. Gaseous reduction using fluidized bed technologies is the most competitive in all direct reduction iron-making processes up to now. It has the advantage that ore fines can be directly charged to the process without prior treatment while its disadvantages are particle agglomeration and high gas/solid ratio[3]. To avoid these advantages, a new reactor, multilayer moving-fluidized bed reactor has been developed for carrying out the gaseous reduction. Hydrodynamic behaviors of gas and fines in the reactor were studied and the results were satisfying[4]. However, due to its unique structure of the multilayer moving-fluidized bed and unique gas-solid flow pattern, models of multiphase flow as IPSA, DPM and Eulerian Model could not give a satisfying solution. The current paper is developed a new CFD model and a new solution approach for simulation of the reactive gas-solid flow in the multilayer moving-fluidized bed for its optimization, design improvement and future scale-up."

Jan 1, 2013

By Qionghua Zhou, Wei Liu

"Nanocrystalline silver bulk material with average grain size of 20.3 nm was prepared by warmvacuum- compaction method. The as-prepared nanocrystalline silver was characterized by X-ray diffraction (XRD), differential scanning calarmeutry analysis (DSC), thermogravimetric analysis (TG), and 6157 type Electrometer test, respectivily. The experimental results show that the average grain size and microstrain of the nanocrystalline silver are 20.3 nm and 0.088%. The melting point and melting enthalpy are 1228.7 Kand 82.34 Jig, which are lower than that of coarse-grained silver by 6 Kand 22.6 Jig, respectively. The electrical resistivity of nanocrystlline silver increases with higher temperature when the range of temperature is between 233K and 293K. The electrical resistivity at 293 K is 1.475xlO -7 Q·m, which is higher than that of coarsegrained silver by a factor of 9.IntroductionN anocrystaline ( nc) materials or nano structured ( ns) materials are three-dimensional (3 D) bulk materials with average grain size typically smaller than 100 nm. Ne materials have been of great interest for their unique properties, such as superior tensile strength [1-2], high microhardness [3- 4], superplasticity [5-6], magnetically quasi-isotropic [7-8] , and so on, making them one of the most promising nano-scale materials with wide applications. Ne materials with average grain size of 5-10 nm were firstly fabricated by Gleiter et al. [9] in 1980s, using inert gas condensation (IGC) method. Unfortunately, the large surface to volume ratio creates a high surface energy component in the total free energy of the system and results in a metastable state in the materials. Therefore, due to the signfica nt disordered grain boundary regions, nanomaterials are thermally unstable and are subjected to a strong driving force for grain growth. The grain growth even occurred at room temperature [10].The conflict or deviation of measured date, e.g. strength, microhardness, thermal stability, partly due to the grain boundary ratio or the distribution of grain size, and partly derived from imperfections such as voids and microcracks while earlier processing techniques are known to result in incomplete dens:fication [11-12]. Therefore, the higher quality samples produced in subsequently years still show such a general trend."

Jan 1, 2011

By G. L. Liu

"Deformation Banding ( DB ) in cold rolled mild steel has been experimentally established by microstructure investigation. Deformation banding model includes such deformation mode when it is applied to rolling texture simulation. The cause for the occurrence of deformation banding is the reduction of the total work for plastic deformation through a relaxation of the deformation constraints. In the first DB model, all grains are assumed to band from the first deformation step. Such an unrealistic assumption has been eliminated in the new model by the introduction of a banding criterion based on an energy minimizing approach. The prediction is closer to the measured texture by applying banding criterion and setting critical resolved shear stresses (CRSS) ratio for { 110 } and { 112 } slip modes to 0.85.IntroductionBased on the continuum theory of plastic flow and deformation mechanism of crystallographic dislocation slip, Taylor's FC ( Full Constrain ) theory [1] has been widely used in texture modeling. As the process of cold rolling of sheet materials produces a microstructure consisting of elongated or equiaxed flat grain or cell, the ""lath"" and ""pancake"" relaxed constraints ( RC ) models [2, 3] were introduced as the successful improvements over the classical FC model. It has been also recognized that crystals may split into different orientations during deformation and the term deformation banding is used to describe such deformation processes [4, 5]. Lee et al. [6, 7] pointed out that the success of the RC theory in predicting textures depends on the physical processes of deformation banding. They developed so called Deformation Banding ( DB ) model by considering DB in the longitudinal plane to be accounted for by the RC method and allowing DB in the rolling plane. DB model was applied to simulate the texture development in bee case [8], the predicted bee rolling textures are in reasonable agreement with the measured textures. In the first DB model, however, all grains are assumed to band right upon the first deformation step. A banding criterion was formulated [7] which states that DB will occur if the work used in DB model is less than that in RC model. Such criterion has been incorporated into the original DB model for texture simulation and is referred to as DBC ( Deformation Banding Criterion ) model."

Jan 1, 1998

By Yanhui Sun, Yanan Zeng, Kaike Cai

"Hot ductility of Nb-V-containing steel has been studied by theoretical calculation and thermal simulation experiment. Meanwhile, microsegregation and precipitates were analyzed. The results showed that segregation degree of elements S, P, 0 is greater in mushy zone, while, the hot ductility was deteriorated by inclusions of Fe(S,O), (Fe,Mn,Si,Al)(S,O) in the interdendritic region. At the temperature 1100°C, a few NbN particles, 60-70nm, have little effect on mechanical property. In the temperature range 1000°C to 975°C, R.A declined rapidly from 82.36% to 69.61% with the diameters decreasing from 20 to 10nm and quantity of particles increased 23 to 45inds/µm2, respectively. In the temperature range from 900°C to 850°C, R.A reduced unobviously from 34.27 % to 30.01 % with ferric films thickening gradually. The critical stress, 52.38MPa, was equal to tensile strength at 975°C. Intergranular fracture was easy to occur with higher critical stress below 975° C.IntroductionProductivity and product quality of slab are seriously affected by cracks during continuous casting and the influencing factors of cracks are various[l]. From microcosmic angle, resisting deformation ability of initial solidification shell decreases obviously with solute elements segregation which can urge the low melting point ofliquid film to form at grain boundaries[2, 3]. Meanwhile, with temperature decreasing, particles would precipitate as the practical solubility product is greater than equilibrium solubility product. The carbonitrides would lead to stress concentration at austenite grain boundaries. Therefore, the transverse cracks of microalloyed steel would form during the straightening operation in the continuous casting process. The hot ductility of steels in the temperature of mushy zone was characterized by microalloy elements segregation, zero strength temperature (ZST) and zero ductility temperature (ZDT). The nature, shape, and size of precipitates have been investigated by TEM (JEM2100). Hot tensile test with low strain rate was simulated by Gleeble-1500. The objective of present study is to provide reference for zero defect of microalloyed steel during continuous casting process."

Jan 1, 2013

By Miaoyong Zhu, Sen Luo

"A two-dimensional CAFD model was developed for simulating the solute diffusion-controlled dentritic growth in the low Peclet number regime. Mass conservation and local equilibrium at the solid/liquid interface were solved to determine the growth velocity of interface with consideration of constitutional and curvature undercooling. The modified decentered square growth proposed by Wang et al was adopted to capture the first eight neighboring cells. The comparison between the classic Lipton-Glicksman-Kurz (LGK) analytical model for steady state tip variables and the simulated values showed that the present model was capable of quantitatively determining the dendritic growth, and the simulation tests demonstrated that the effects of the mesh anisotropy in growth kinetics and crystallographic orientation were eliminated. The numerical simulations were performed to the dendritic growth ofFe-0.6%C binary alloy in undercooled melt, and the results showed that the present model could predict the dendrite morphology with artificial growth orientation in acceptable level.IntroductionDuring the solidification of metals and alloys, the dendrite grows from the substance or the undercooling melt and solute redistributes between the dendrite and the interdendritic liquid. The solidification microstructure is close related to the phase and solute evenness and has a close linkage with the properties of final production.In the past few decades, various kinds of deterministic and stochastic models have been developed to predict the evolution of microstructures in solidification, with the fast development of computer power. Among these methods, Phase Field (PF) model [1, 2] has been known as one of the most adequate deterministic models for directly simulating the dendritic growth. However, there is a vital drawback that the PF method requires considerable computation time and is limited to simulate very small domains with a few dendrites [3]. On the other hand, stochastic models, such as Monte Carlo (MC) method [4, 5] and Cellular Automaton (CA) method [6-8], have been usually applied to predict the solidification microstructure evolution. Comparing with the MC method, the dendritic growth kinetics is explicitly integrated in the CA model, while the MC model doesn't. Therefore, the CA method is more reasonable to predict the dendritic growth during the solidification of melt."

Jan 1, 2013

By K. Itagaki, H. Henao

"The experimental study on the phase equilibrium and distribution of minor elements such as chromium and copper between magnesia saturated FeOx-MgO-SiO2 slag and Fe-Ni alloy were carried out under controlled oxygen partial pressure between 10-6-5 and 10-10 using CO and CO2 mixed gas at 1773 and 1873 K.The effect of slag additives such as lime (CaO/SiO2 molar ratio: 1) and alumina (AlO1.5/SiO2 molar ratio: 0.1) on the distribution behavior of the minor elements was also investigated.The value of distribution ratio for chromium, defined by (%Cr in slag)/[%Cr in alloy], is larger than 70 at the pO2 region conducted in the present study for the MgO saturated FeOx-MgO-SiO2 slag at 1773K. These value are almost 4-order higher then that of nickel though the distribution ratio of copper shows similar values with nickel. Analysis of the data indicates that addition of lime in the slag and the increase of temperature reduce the dissolution of chromium into the slag and the addition of aluminum increases the dissolution of chromium into the slag while reduces the dissolution of copper and nickel.IntroductionChromium. is a minor element in a nickel oxide ore but a Japan major component in the secondary material of stainless steel and is also introduced in the Fe-Ni production process due to dissolving bricks of a furnace. Chromium is a concerned matter for the beneficial utilization and disposition of ·slag because Cr6+ is a harmful element. Considering Fe-Ni as an alloy component in steel making, and the demand of high purity nickel, chromium is an -undesirable element that has to be eliminated into slag prior to the steel making, or the production of high temperature refractory alloys. On · the other ·hand chromium is an element of steel alloy for many applications, thus Fe-Ni containing chromium in minor element is desirable in some stainless steel making."

Jan 1, 2000

By T. T. Chen, J. E. Dutrizac

"Grooved cast Pb-Ag anodes are used by some zinc refineries to improve current efficiency. It was found that the manganese oxide scale formed on a grooved Pb-0.75% Ag anode consists mainly of MnO2, which occurs characteristically in rhythmically banded colloform structures and adheres to a layer of ""Pb02+PbS04"" that oxidized from the anode. The relatively homogeneous and nearly fracture-free morphology of the ""Pb02+PbS04"" layer suggests the relatively uniform corrosion of the anode. Deposition of the Mn oxide initially follows the contours of the anode surface, but the grooves eventually become filled with Mn oxide and gypsum. Hydrous Mn oxides and amorphous Mn oxides are believed to be also present in the manganese oxide scale. Tiny particles of PbS04 and SrS04, together with gypsum, other impurities and micro-pores, tend to concentrate in the grooves.IntroductionManganese is a common impurity in hydrometallurgical zinc processing circuits. The manganese originates from sphalerite (Zn,Fe,Mn)S and from the Mn02 added to the leaching circuit to oxidize ferrous ions [1]. Manganese in the sphalerite follows Zn through the roasting, leaching and purification processes, and is present as Mn(II) in the purified ZnS04 solution. The Mn in the added Mn02 is reduced to Mn(II) during the oxidation of the ferrous ions present in the leach solutions. In both cases, MnS04 is generated, and the MnS04 accumulates in the purified solution. In the cellhouse, Zn is plated at the cathodes to produce high quality metal. The Mn(II) is partly oxidized at the anode surface to Mn(IV), and the Mn(IV) precipitates as a scale on the surface of the anode and as a sludge on the bottom of the electrolysis cells. The presence of a thin layer of manganese oxide scale on the surface of the Pb-Ag anode can minimize the corrosion of lead and, accordingly, reduce the contamination of the electrodeposited zinc. However, a heavy manganese scale build-up can cause ""staining"" of the zinc deposits and reduced current efficiencies. Consequently, periodic anode cleaning to remove excess manganese oxide scale is carried out routinely in commercial operations."

Jan 1, 2011

By Gökhan Demirci, Ishak Karakaya

"Energy consumption in electrolytic magnesium cells is well above the theoretical values. However, the mechanism of the back reaction, the main cause of the current losses, has not been fully understood yet. Magnesium dissolution into the melt is generally regarded as the limiting step for the back reaction. Accordingly, present cell designs are made with priority given to fast magnesium removal from the cell. However, experimental data and modeling results in this study indicate that the limiting step for the back reaction between magnesium and chlorine is the chlorine dissolution into the electrolyte when physical contact between electrolysis products was eliminated. Effects of chlorine bubbles on the current efficiency and the cell potential were investigated. Results show that the extent of back reaction is proportional to the chlorine surface area in contact with the electrolyte per unit time, and the cell potential increases with the amount of chlorine bubbles inside the electrolyte.1. IntroductionMagnesium is less dense than the electrolyte in electrolytic magnesium production. Therefore, both electrode products, magnesium and the chlorine gas, move upwards inside the molten salt electrolyte during electrolysis. The upward motion of electrode products promotes the most important current loss mechanism, the ""back reaction"". Separation of the highly reactive species; liquid magnesium and the chlorine gas in the cell, to prevent their recombination is one of the main concerns in cell designs. The employment of large inter-electrode distance or a separation wall in early cell designs; decreased the extent of recombination, but increased the cell voltage and energy consumption. Recent cell designs, on the other hand, make use of lifting action of chlorine gas [1,2] by utilizing smaller inter electrode distances to separate the magnesium and chlorine gas faster. Although energy consumption was reduced, but more physical interactions between electrode products make electrolytic magnesium cells still highly inefficient when energy consumptions are compared with the theoretical values. Today, the most efficient industrial cells utilizing high purity feed operate at 10.5-11.5 kWh kg-1 Mg [3-5] and it is considerably higher than the theoretically attainable value of about 6.0 kWh kg-1 [6]. This large gap demonstrates the necessity of more research on physics and chemistry of magnesium cell electrolysis."

Jan 1, 2011

By Vladimir Lobanov, Pritchinm Alexander, Nikifor Ageev

"Sulfuric anhydride is one of the most voluminous technological emissions. The possibility of high-temperature SO2 oxidations without catalyst in presence of calcium-bearing filling materials (CaO, Ca(OH)2 and CaCO3) with obtaining of binding material on the basis of waterless calcium sulfate is studied. Due to application package HSC-4 the thermodynamic analysis of the specified interactions is made and following conclusions are drawn: 1) Reactions are feasible in the all range of investigated temperatures (400 – 1000 °?); 2) The best results should be expected at use of ???; 3) The heat of reaction does possible autogenous behavior of process. The researches have shown: 1) Practical possibility of the process; 2) SO2 oxidation without the catalyst is feasible in presence of ???, Ca(OH)2 and CaCO3; 3) The optimum temperature range is 600-800 °?; 4) The content of waterless calcium sulfate in a product reaches 48% that makes it possible to use as the binding material; 5) At excess of ??? the degree of SO2 collection is nearer to 100%. Introduction At processing of sulfide raw materials in metallurgical furnaces the significant amount of sulfur, mainly in the form of sulfuric anhydride is escaped. Rich gases (SO2>3 %) are used for the sulfuric acid or element sulfur production. Chemism of sulfuric acid manufacturing is based on catalytic high-temperature oxidation of anhydride. Poor gases of metal works (SO2 =2,5 %) and power combustion units (SO2 =0,5 %) after clearing discharge into the atmosphere. Commonly, to recovery of weak sulfuric anhydride the chemical and physicochemical methods are applied. A few chemical ways of recycling sulfur dioxide are applied practically. In a number of methods for SO2 recovery a pulp of metals oxides (magnesium, zinc, etc.) with formation of sulfites is used. In other case sulfuric anhydride is catch by weak sulfuric acid in the presence of an oxidizer (pyrolusite ore). Methods of absorption SO2 by solid sorbents, (carbon fibers, silica gels, zeolites) are known and put into practice. Regeneration of the saturated sorbents is realized by thermal decomposition or extraction. Obtained as a result high-concentrated solutions are a commercial product."

Jan 1, 2008

By P. C. A. Maia, J Alexandre, F. A. J. Saboya, A. R. G. Azevedo, G. C. Xavier

"This work shows the characterization of clay and the granite waste by-product from the sawing process of the granitic blocks, used as raw material for brick ceramic. Besides, shows the degradation of the ceramic material obtained with different by-product contents in the waste after lab test degradation, is investigated. The clay is obtained from mine use areas of ceramic industry in Campos-RI and the waste is originating from of the area of Cachoeiro-ES, an important center of decorative stone in Brazil. The mixes were made by the addition of 0% up to 10% of the waste in the raw material. After drying and firing up to 900°C, obtained prismatic pieces were considered intact. Physico-mechanical properties were obtained from wet and drying tests in laboratory considering 50 and 150 cycles. The results showed that the use of powder byproduct has a considerably influence on the weathering and strength of the material.IntroductionThe ornamental rocks and coating defines the most promising areas of business in the mineral sector [l]. In this context, the Espirito Santo appears as the main Brazilian state in production and export of ornamental rocks, representing 47% of national production [2] which in tum is one of the economic sectors most representative of this State, due of its transport logistics and port vocation that facilitates the export of such products.It is estimated that the state of Espirito Santo there are approximately 1,200 companies dedicated to the activities of ornamental rock by providing 20,000 direct jobs [ 1]. These mobilize support activities, such as companies that provide machinery, equipment and supplies for industries, including service providers for maintenance.However, the production of rocks produces about 15,000 tons of granite waste/month [3] only in the municipality of Cachoeiro ltapemirim-ES. This is justified by the presence of more than 500 extraction industries, cutting and processing of stone, with about 900 looms, waste generators.According to [4], there is great potential for the use of granite waste in red ceramics introduced for the manufacture of bricks, blocks structural ceramics. and other ceramic products, especially when evaluated on exposure to weathering."

Jan 1, 2014