Search Documents

By Shigehisa Endoh, Hitoshi Ohya, Atsushi Inaba, Shigeki Koyanaka

"Recycling should be promoted to keep the global environment. However, it is difficult to detennine the quantitative impact. A life cycle assessment is one of the most reliable methods to estimate the global environment impact.Exergy is useful like entropy when considering the sustainable development. All of our activities have been obtained exergy resources and/or energy itself and throw away waste and/or waste heat. We are trying to use exergy to estimate the quantity of energy and matter for resource accounting. For recycling plastic, plastic has two aspects; material and energy source.The environmental assessment of plastic recycling suggests that the exergy reduction of the entire system is estimated by the yield of matter and the process efficiency. The material recycling is better than the thennal recycling when the process efficiency is high. However, the thennal recycling is much better for the low efficiency. The transition point is able to be decided by the efficiency of the manufacturing and the electric power generation.IntroductionRecently, many of the global environmental problems have become conspicuous like global wanning, ozone layer depletion and acid rain. Some of the methods like life cycle assessment for solving these problems have been presented. Anxiety concerning the proble1ns of energy and resources has led to a rapid increase in the interest in describing and understanding the conversion processes of energy and other resources in today's society. All human activity is supported by obtaining power and products of high exergy from the environment and throwing away the waste material and the waste heat of low exergy back the environment. However, the total exergy in the whole system becomes absolutely smaller than before.The rate of obtaining high exergy products and energy itself by human activity and the speed, by which waste and waste heat having low exergy are thrown away are too fast to attribute to environmental problems [1-3].A material's use by recycling was often common in a circulating society mainly. A significant amount of energy is consumed during circulation. An environmental impact assessment method for the process or the system has not been devised when both of them are taken into consideration. Even if the life cycle assessment evaluation, which has been correctly used up to now, is applied, it is not sufficient for an overall evaluation concerning matter and energy.The real sustainable development is that the exergy reduction value by all human activities on the earth is kept within the range of the exergy reduction in order to consider the earth as closed stationary system. It is important to evaluate the process or the system by using the exergy, and design them so that the exergy loss may decrease as much as possible. We have to consider what process improvement is the most effective."

Jan 1, 2000

By Paulo von Krüger

This paper deals with the cell design and operation of a tin electrorefining 1:5 pilot plant. The purpose of the work was the fitting of the basic parameters to be used in a full-scale tankhouse from a major Brazilian tin producer. The main specific difference was the use of permanent stainless steel cathodes instead of conventional tin starting sheets. The results of both product quality and operating parameters are discussed.

Jan 1, 2003

By W. Y. Kim, K. H. Song, K. Nakata

"The present study was carried out to evaluate the mechanical properties of friction stir welded Inconel 600/SS 400 lap joints. In this process, friction stir welding (FSW) was performed at a tool rotation speed of 200 rpm and welding speed of 100 mm1min, and argon gas was utilized to prevent surface oxidation during the welding. Application of FSW notably decreases the grain size of Inconel 600 alloy from 20 µm in the base material to 8 ~ in the stir zone. However, the grain size of SS 400 in the weld zone was slightly coarsened, when compared to the base material. Also, the hooking in the advancing side and the intermetal1ic compounds (M7C3) in the weld interface between Incone1 600 and SS 400 were well formed. These intermetallic compounds and hooking were effective to increase in mechanical properties such as tensile and peel strengths.IntroductionFriction stir welding (FSW), applicable welding process at solid state, has several advantages in defect suppression such as blow hole, segregation and cracking which mainly occurs in fusion welding [1, 2]. Notable grain refinement in the stir zone due to FSW can expect the outstanding increase in mechanical properties of the welds. In constructing the chemical and power plants, Ni base superal10ys have been used in many parts, moreover, fusion welding as construct method, such as gas tungsten arc welding, electron beam welding and laser welding, has been mainly used [3-5]. However, fusion welding has a limit in an increase in chemical and mechanical properties in the welds. Lately, Ni base superalloys to which FSW applied have been reported with notable enhancement in mechanical properties, which resulted from refined grains in the welds [6-10]. These researches showed the possibility in applying the FSW, directly."

Jan 1, 2012

By S. Kawamura, H. Inoue, Y. Maeda, H. Ohike

Kosaka smelter is a copper smelter located in Akita Prefecture in the northern part of Japan. It has treated complex sulfide concentrates for a long time. Recently, in addition to metal production from ores, the company has been working on the recycling of metals by using this metallurgical technology. Metals recovered are primarily gold, silver, palladium, copper and lead from copper scraps, electronic board scraps, silver oxide batteries, spent lead acid batteries, semiconductor chips, cellular phones, and automotive emissions catalyst. In particular, electronic board scraps and cellular phones can be valuable raw materials. These electronic scraps are fed into the flash smelting furnace after size reduction in a shredder that was introduced in 1999. Due to the growing demand for personal computers and cellular phones, the amount of electronic board scraps available for recycling increased. At present, these secondary materials are good raw materials for Kosaka smelter since the smelter is already used to dealing with complex raw materials. The recycled metals account for up between 5 and 20 percent of the total production at Kosaka Smelter. In particular, over 90 percent of the palladium in the secondary materials can be recovered.

Jan 1, 2000

By Cyro Takano

This paper is a contribution to fundamentals data on the equilibrium metal/slag for refining silicon in relation to Ca and Al as impurities. Silicon containing 0.1% Al and no Ca was placed in contact with a slag of various contents of CaO, SiO2 and Al2O3. Slag Al2O3 contents were 11.4%, 25.1% and 29.6%, keeping the ratio %CaO/%SiO2 constant and equal to ~0.53. The experiments were conducted at 1550oC, in a graphite crucible with argon atmosphere. The equilibrium was observed with low and medium content of Al2O3. The derived activities coefficients of Ca and Al in dilute solution of Si presented good correlation with those of the literature. Parallel reactions with formations of SiO(g) and CO (g) were also observed.

Jan 1, 2006

By William Petruk

A mineralogical and image analysis study was conducted on samples of U tailings from pilot-plant runs on Midwest ore in Northern Saskatchewan. The tailings had been subjected to simulated weathering for the equivalent of 10 years in a tailings facility (lysimeter). The pH varied from 7.0 at the beginning of the test to 5.9 at the end. The results show that during the simulated weathering sane of the gersdorffite, uraninite, galena and pyrite had oxidized, with gersdorffite being the most reactive and pyrite the least. Reaction was evident at the top of the lysilleter , but was most intense at the seepage discharge. sane of the released ions precipitated as Ni, Pb, and U arsenates, sulfarsenates, sulfates and oxides on particles of all minerals. Green crystals of Ni sulfate and white crystals of ca sulfate had precipitated at the surface of the lysilleter. Clay minerals and chlorite had washed from the top of the lysirneter towards the seepage discharge.

Jan 1, 1989

By Ma Ying

The continuous directional solidification technique of five kinds of special ZA alloys with eutectic, peritectic and eutectoid transfonnation under the condition of continuous casting by heated mold was studied. The mechanism of surface defects appearing in ZA alloy line was discussed and the structure of some defects were analyzed by SEM. The results show that only when the fitting of various technique factors, pressure head, outlet temperature, pulling speed and cooling condition are reasonable under a certain range, can the ZA alloy smooth line be continuously pulled out. Unreasonable techniques will result in hot tear, rough surface, mush outlet, leaking and other defects. The shape and location of solid-liquid zone have an important influence on the formation of the above defects. When the solid-liquid zone is located in the mould outlet or inner mould, the surface of solidification will protrude into the inner mould. If the remaining liquid cannot counteract the solidification contraction, a rough surface will appear. If the solidification surface further into the mould, the ingot in the mould will have a great friction force when pulling and will form a hot tear. When the solid-liquid zone is moved out of mould, the solidification surface will turn into a plane, which easily results in leaking. A vibration or unstable operation will cause an ingot winding during pulling.

Jan 1, 2003

By Mamoru Kuwahara, Tomohito Taki, Masamichi Sano

"Theoretical basis and experimental results on ultrasonic separation of dispersed inclusions from molten metal are outlined. Transitional formation of an ultrasonic standing ·wave field in a liquid bath is numerically predicted based .on the wave equations. Numerical solution of the equation of motion of a fine particle in a standing wave field indicates that the inertia term can be neglected during conventional ultrasonic separation of fine particles: Analytical solutions for the position at which particles are coagulated the minimum power for separation, and the ultrasonic separation time are derived to incorporate such key process parameters as the density difference and the acoustic energy density exerted. Cold model experiments have been carried out to observe ·transitional coagulation of polystyrene particles in an aqueous sugar solution with the incidence of standing ultrasonic plane wave. Experimental results agree well with the theoretical predictions.IntroductionDespite of recent progress of fundamental and applied researches in metallurgical systems, advanced materials· with less inclusions and better properties may demand more innovative processing in a: molten state. It may be realized by applying electromagnetic and/or ultrasonic external fields to the systems. The present authors1)·2) have been proposing : new methods of ultrasonic processing of materials based on such phenomena as acoustic streaming, acoustic radiation pressure on dispersed phase in a standing wave field, and the cavitation in liquid associated with use of high-intensity ultrasound and so on. Taking account of common physical natures between ultrasound and sound wave, we call such · a processing assisted by acoustic wave as ""sonoprocessing"". This report ·deals with some theoretical and technological aspects on the ultrasonic separation of fine particles from liquid, which could become an important operation to produce clean materials. Fundamental theory and ·supporting experimental results will be given below to give an insight into the liquid metal sonoprocessing."

Jan 1, 2000

By E. T. de Groot, D. L. Verhelst

With the successful start-up of Cominco's new KIVCET smelter, the final key component is now in place for Trail Operations to operate efficiently as a modern integrated zinc-lead facility. Unique metallurgical, operational, planning and management issues apply to this operation. Along with presenting the current flowsheet for Trail Operations, this paper discusses issues such as the impact of recycles, operational re-stabilization following significant process changes, plant operation with just-in-time inventories, real-time process optimization, and management philosophy.

Jan 1, 2000

By Guozhu Ye

"One of the most essential problems associated with the treatment of EAF dust is its high content of halogens. For most thermal processes for zinc recovery, such as the plasma processes with a zinc condenser, the halides in the gas stream will form a dross phase that results in a low zinc yield. For those with zinc oxide as main product, such as Waelz oxides, the high halogen content in the product implies a great degradation of the product quality and the product can only be sold at a low price. Further processing of zinc oxide with high halogen content either by pyrometallurgical or hydrometallurgical processes will also result in process problems.This paper will review the pre- and post-treatment alternatives for halogen removal based on the comprehensive characterization work that has been carried out at MEFOS and the preliminary experimental results.The experimental results show that chlorine and fluorine content could be reduced to 450 ppm and 50 ppm respectively by selective sulfation, and to about 200 ppm by soda leaching. Selective sulfation of zinc oxide in the EAF dust will also be discussed."

Jan 1, 2000

By M. M. Coleman

An investigation of the behaviour of sphalerite, chalcopyrite, galena and pyrite during flotation was conducted on selected circuits in the Brunswick Mining and Smelting Corporation Ltd. concentrator in Bathurst, NB. Samples were collected from 59 locations and analyzed for Zn, Pb, Cu, Ag, Fe, As, Sb, Sn, Bi and S. Metal balances were computed using the CAMP Material Balance Program (MATBAL 5) and the metal recoveries for each cell and circuit were calculated. An automated image analyzer interfaced with an electron microprobe was programmed to measure the size of sphalerite, chalcopyrite, galena and pyrite grains in each sample. The percentage of each mineral occurring as free grains and the relative amount of each mineral present in binary and ternary particles was calculated. The recoveries and losses of Pb, Zn and Cu are compared with the amount of liberated and unliberated galena, sphalerite and chalcopyrite present in the concentrates and tailings.

Jan 1, 1989

By A. M. Blount

In 1983, a final ruling of the U.S. Occupational Health and Safety Administration (OSHA) specified that chemicals containing >0.1 % of a carcinogenic substance or > 1 % of a substance hazardous to health must be labelled. Amphiboles of the fibrous or asbestos-type must be quantified at levels of 0. I % whereas the status of non-fibrous types is not finally determined at this time. Tremolite and actinolite can possibly be measured to 0.1 % by XRD, but anthophyllite cannot be so measured. Recently the International Agency for Cancer Research (IARC) has designated quartz as a suspected carcinogen, and its quantity must be measured to the 0.1 % level. Thus, it has become Increasingly important to be able to detect and quantify minerals in bulk samples down to low or "trace" levels. It has been found that minerals needing to be quantified can often be concentrated by microcentrifuge and counted by means of polarized-light microscopy. For example, amphiboles in talc samples can be separated by using a heavy liquid (thallium formate-malonate) of density 2.810. Talc floats, and amphiboles sink. After centrifuging, the denser particles are removed from the bottom with a Pasteur pipette and placed in a clean centrifuge tube. Distilled water is added to the tube containing the denser minerals and the tube centrifuged again. After several washings with distilled water, the sample is removed along with a drop of water to a clean glass slide. A drop of 1 .584 refractive index liquid and a cover glass are placed over the dried sample. The slide is scanned for particles greater than 5 um in length and having an aspect ratio greater than 1:3. These are checked for refractive index, sign of elongation and extinction angle to differentiate them from talc particles on edge and other minerals. Amphiboles have all indices greater than 1.584, and talc has all indices equal to or lower than this value. Alternately the heavies at the bottom of the centrifuge tube can be filtered through a nucleopore filter. After the filter has been washed with distilled water and dried, a 1.584 refractive index liquid renders the filter transparent in two of the four extinction positions so that a count of amphibole particles can be made directly on the filter. The refractive index-density method which is so useful for talc powders should be equally useful for other nonsoluble industrial minerals.

Jan 1, 1989

By P. R. Taylor

Diamond films have been successfully formed in an inductively coupled plasma (ICP) chemical vapor deposition (CVD) system from several gas mixtures: CH,-H,, C2112-112, and C2112-112-02' Our previous thermodynamic study indicated that the substrate temperature could be lowered by the presence of oxygen species at moderate system pressures (0.3-0.5 atm) and that higher volumetric growth rates required a high temperature source and a moderate pressure system in CVD processing. The principal experimental results were consistent with the thermodynamic predictions. The deposited films were characterized by laser Raman spectroscopy, scanning electron microscopy, and X-ray diffraction. The films were well faceted and uniform, with the growth rates over 10 pm/hr on molybdenum substrates. The crystal size ranged between 1 and 2 microns for a two hour experiment. It was possible to decrease the substrate temperature to below 800 °C in this system.

Jan 1, 1995

By Mitsuhiro Ohtaki, Tetsuzo Arakawa, Fujio Murata

Refining of Zn from aluminum scrap melt by some vacuum distillation processes was studied to promote aluminum scrap recycling. Effects of distillation conditions, such as melt temperature, vacuum pressure and holding time, on Zn distillation behavior were investigated theoretically and experimentally by 0.3kg/ch scale vacuum resistance furnace. Three methods to increase the surface-area/volume ratio of liquid metal, such as gas atomizing, mechanical atomizing and mechanical stirring, were tested to increase the Zn distillation rate in 5kg/ch scale vacuum resistance-furnace. It was easy to lower the remaining Zn content to less than 0.1 wt% within one minute by mechanical stirring method. A water-model simulation experiment indicated that a significant agitation of the melt by stirring would be effective to increase the distillation rate. Continuous agitation vacuum distillation process (CA VP) has been designed and the pilot plant is now in construction.

Jan 1, 2000

By James R. Myers

A source of clean gas containing sulfur dioxide and sufficient oxygen for convers.ion to sulfur trioxide ?is essential to the production of sulfuric acid. S02 containing gases obtained from roasting sulfide ores are heavily contaminated with inorganic dust and volatile impurities. If not removed, these contaminants will reduce product acid quality, foul the catalyst beds and mist eliminators, and accelerate equipment corrosion. This paper reviews conventional gas cleaning systems for metallurgical acid plants, followed by a discussion of modern systems utilizing DynaWave Scrubber technology. This technology is based on a unique approach to? gas scrubbing that can concurrently accomplish several gas cleaning/processing tasks scrubbing liquid is injected into the gas stream to create. a "Froth Zone". This is a region of extreme turbulence, with a very high rate of liquid .surface renewal. It efficiently removes both particulate matter and gas contaminants, and is also a cost effective quenching device for gases as hot as 1250º C. Smelter

Jan 1, 1992

By De-qing Geng, Guang-liang Wu

The waste slag generated by the LF refining process of Q345B low alloy hot-rolled steel, still has some refining capabilities. If recycled, it can reduce environmental pollution, and save the economic costs. A research on melting Characteristics of Q345B steel LF refining waste slag was investigated by using orthogonal experimental method, and the effect laws of composition on that were analyzed. Through variance analysis and significance criterion, it is concluded that the optimum ingredient of the regenerated LF refining slag is 25%A12O3, 12%CaF2, 7%MgO and R= (CaO)/ (SiO2) =2.5. And the regression analysis is carried out by using SPSS software, to get the mathematical relationship between ingredient with high reliability and melting temperature of refining slag T=1451.3-6.25CaF2+2.36 R.

Jan 1, 2016

By M. Misra

The bacterium?Mvcobacterium Phlei has a demonstrated potential to be used for the flocculation of a variety of finely divided minerals. The microorganism possesses both hydrophobic surface and high negatively electrostatic charge. It can adhere to many mineral surfaces ?if the charge and hydrophobic interaction? between the microorganism and the minerals are favorable to adhesion. Experimental results showed that the dolomitic phosphate slime from Florida and fine hematite can be :readily flocculated from dilute suspension.. In the case of dolomitic phosphate slime, a consolidated sediment containing 24'-25 weight% :solids can be obtained from .a dilute slurry .in a short time. Sediments obtained from hematite flocculation are rather massive and more .consolidated than phosphate slime. Mycobacterium Phlei has a specificity for selective flocculation of hydrophobic fine coal particles from pyrite and ash containing minerals. Because of mutual hydrophobic interaction of coal and Mycobacterium Phlei, it was noticed that coal particles appear to be strongly held in the aggregate by adhesion or bridging of bacteria. However, Mycobacterium Phlei is not a good flocculant for either associated pyrite or ash present in coal.

Jan 1, 1991

By Honglei Zhang, Wuguo Xiang, Xinhao Huang, Guotao Xu, Xilai Chen

"The service behavior of refractories used in hot air pipeline for hot air stoves in a 3200 M3 blast furnace of WISCO was analyzed. The damage factors can be concluded as the poor quality of and alusite based bricks, the severe thermal shock damage, the more porosity in structures, loose bonding capability, and the unreasonable choice of materials and design of bricks. By analysis, the service life of hot air stoves can be enhanced by the measurements such as the reasonable choice of materials and their match, the use of light-weight refractories, the improvement of brick type, etc. Thereafter, the normal production operation of hot air stoves is guaranteed.IntroductionThe No.7 blast furnace of WISCO has been used for about 5 years and it was mid-repaired in March, 2012. The top phenomena of worn hot air pipelines are brick drop, breakage, severely local wear and deformation, existing hidden danger, so the worn hot air pipelines were renewed. Investigations have been done on the stove damage and design [1,2]. In order to clarify the wear mechanism, the used refractories for hot air pipelines were sampled and analyzed, the properties and structures of worn materials and reused materials are relatively studied."

Jan 1, 2013

By E. S. Peterson

The selective separations of trace metals- and organics from water are processes of importance to industry. The application of a new metals capture technology coupled with polymer membrane technology has proven to be one avenue to accomplish such selective separations. The polymers used in these studies are polyphosphazenes. Polyphosphazene polymers consist of an alternating backbone of nitrogen and phosphorus atoms. The polymers have high thermal and chemical stabilities. Experiments at the Idaho National Engineering Laboratory demonstrate that polyphosphazene membranes coupled with Chromato Chem,"Chelation Chromatography" process are capable of removing both chlorinated hydrocarbons and metal ions from process streams. These results point to a wide range of potential industrial and environmental applications for such systems. Data will be presented which show the efficiency and selectivity of separations, postulated separation mechanisms, and the initial designs of industrial demonstration units which are currently under construction. Parts of this work have been performed under a Cooperative Research and Development Agreement (CRADA) between ChromatoChem, Inc. and Idaho National Engineering Laboratory (INEL). The work at INEL was been sponsored by the United States Department of Energy's Office of Industrial Technologies

Jan 1, 1995

By Masahiro Hirasawa

"As a fundamental study on pyrometallurgical process that involves recycling steel-making dusts, of which major components are oxides of Zn and Fe, and waste polyvinyl chloride simultaneously ·at. a temperature below 1273 K, the reactions between the mixture of ZnO + Fe20 3 and PVC or the compound ZnFez04 and PVC are investigated in a series of thermogravimetric and small scale reactor experiments under inert atmosphere at below 1273 K. The reaction mechanisms are discussed· on the .basis of the thermogravimetric data. From the results of reactor experiments, it is shown that the chlorination of Zn in the oxides by Cl in PVC, the vaporization of ZnC12, the reduction of iron oxide to metal Fe by C and H in PVC, and, thereby, the separation of Zn and Fe in the oxides take place simultaneously at the temperature ~= 1200 K.IntroductionSteelmaking dusts are metallurgical wastes consisting mainly of oxides of Zn and Fe with smaller amounts of other heavy metal elements, such as Pb. In the recent investigation, [1] the present authors have investigated the fundamental aspects of a potential pyrometallurgical process· of recycling steel-making dust with polyvinyl chloride (PVC) at temperature T < 1273 K under Ar atmosphere. The performance of a similar process, in which HCl in the combustion gas of PVC is used to chlorinate Zn in the EAF dust under oxidizing atmosphere, has been investigated by Tailoka and Fray [2] with fundamental experiments. Figure 1 shows an example of the potential ·diagram of Zrt-Cl-0 and Fe-Cl-0 systems. In the figure, we can find two regions where ZnCl2(g) can be separated from Fe containing compounds. One is ZnCiz-Fe20 3 coexistence region at higher oxygen and chlorine potentials and the other is ZnCl2-Fe coexistence region at lower oxygen and chlorine potentials. The process adopted by Fray and coworkers is aimed mainly at the performance of Zn/Fe separation in the higher oxygen potential region. In the present study, the lower oxygen potential region is focused on."

Jan 1, 2000