Search Documents

By J. E. Allen

The trend in refractory technology for the copper and nickel industries has been to higher quality raw materials and improved processing technology. These changes have been dictated by the changes in pyrometallurgical processes in these industries. For example the introduction of flash smelting, reaction type smelting and auxiliary slag cleaning furnaces havedemanded better refractories materials. Extensive field applications and improved laboratory testing procedures have helped make this transition possible. Changes in refractory technology, primarily in basic refractories, are followed from the late fifties to the present and into the future.

Jan 1, 1994

By Bror Nyrnan

Solvent extraction technology and equipment have been developed within Outokumpu since the early seventies. During this period altogether nine solvent extraction processes for molybdenium, zinc, rhenium, cobalt, nickel, calcium and magnesium have been commercially adopted in Outokumpu's metallurgical plants. During last years a new mixer-settler concept based on a "Vertical Smooth Flow" (VSF) principle has been developed. It has also been found to be a good method for copper solvent extraction, decreasing essentially the crud formation and the organic and aqueous entrainments.

Jan 1, 1994

By Joseph D. Lessard

A process simulation of the conversion of molybdenum disulfide concentrates into molybdenum dioxide via the Looping Sulfide Oxidation process has been performed using HSC 7.1 thermodynamic software. By decoupling molybdenite conversion and molybdenum oxidation, Looping Sulfide Oxidation changes the paradigm by turning molybdenite processing into an energy generator while producing a molybdenum dioxide, which has a lower vapor pressure and lower oxygen content than molybdenum trioxide. The Looping Sulfide Oxidation process selectively produces molybdenum dioxide over molybdenum trioxide. This process uses a stoichiometric mixture of oxygen and molybdenum trioxide as oxidants in the conversion of the molybdenum sulfide to the molybdenum oxide. The model simulates the two reactor scheme required by Looping Sulfide Oxidation and incorporates thermodynamic equilibrium simulations performed in FactSage 6.3.1 thermodynamic software. Energy capture is also maximized with heat exchanger systems to transfer heat released in reactions to preheat air.

Jan 1, 2014

By J. H. Puffer

The copper mineralization of the Mesozoic Passaic Formation of New Jersey is typical of copper deposits in eastern North American Mesozoic sediments. Most such deposits are located at the base of the first of several basalt flows that are interbedded with continental, red-bed sediments. The copper mineralization is similar in most respects to that of the Keweenawan Basalts of the Lake Superior area. The first basaltic flow units of the eastern North American Mesozoic basins, and the Keweenawan Basalts, are continental quartz tholeiites of similar chemical composition and copper contents. The copper minerals and associated zeolite facies metamorphic mineral assemblages of these two rock units are also approximately the same. Stoiber and Davidson (1959) suggested that Keweenawan copper was mobilized and concentrated during metamorphism. The evidence pertaining to the Mesozoic copper deposits of New Jersey is consistent with such an interpretation and also with DeVore's (1955) suggestion that ore fluids commonly arise as a result of the mobility of metals under metamorphic conditions. There is additional evidence that final metamorphic concentration of Mesozoic copper was preceded by an initial stage of hydrothermal precipitation related to fluids emitted by basaltic magma.

Jan 1, 1987

By Chunhua Liao, Chao Peng, Guangsheng Huo

To get the separation of tungsten and molybdenum, we adjusted the pH of the solution to 7, at which tungstate (WO4 2-) will be polymerized into HW6O21 5-, while molybdate will still exist in the form of MoO4 2-. Two strongly basic anion exchange resins (D201, D213) were experimented for the separation of tungsten and molybdenum. The results of condition experiments indicate that D213 resin performs better in the treatment of lower concentration solution A (WO3 10g/L, Mo 4.12g/L) with a separation factor as high as 10.64. While D201 resin is more suitable for the high concentration solution B (WO3 70g/L, Mo 28.97g/L) with a separation factor of 6.9. The results of column testing performed on D213 resin show that the solution after loading process with a mass ratio of Mo/WO3 = 50 and the desorption solution with a mass ratio of WO3/Mo = 27 can be obtained

Jan 1, 2014

By Daowu Yang, Zhuo Ren, Hui Liu

"In this paper, the photochemical catalysis degradation effect of photocatalyst obtained by charcoal-supported nano TiO2 (nano TiO2 / charcoal) on the formaldehyde in the air was studied. The influences of the nano-TiO2 loading and the photoreactor structure on the efficiency of photochemical catalysis degradation of formaldehyde was reviewed.The nano - TiO2 / bamboo charcoal adsorption of formaldehyde, as well as the influences of a certain amount of formaldehyde after adsorption on its photochemical catalysis effect were discussed. The sol preparation process of Ce-doped nano-TiO2 was described. Experimental results indicated that: the surface of bamboo Charcoal still has a strong formaldehyde adsorption capacity after Supported by Nano TiO2.After adsorbing formaldehyde, the photochemical catalysis degradation efficiency of formaldehyde of the catalyst at a steady state is basically the same with new prepared catalysts’. When the thickness of the catalyst layer of the multi-ladder-type structure photoreactor is 2mm, the interval is 20mm, the absorption efficiency of formaldehyde of Nano- TiO2 / bamboo charcoal is the best . Nano-TiO2 undoped Ce responded with no degradation of formaldehyde after 2 hours, while the degradation rate of formaldehyde of the Ce-doped nano- TiO2 reached 15% 2 hours late, and the formaldehyde decontamination of the equipment reached 94%.IntroductionEmerging out of home decoration in the distribution of formaldehyde, benzene, ammonia and other indoor pollutants have been proved to be very harmful to the human body. Photocatalysis can eliminate air pollutants, in particular, can effectively degrade the air volatile organic compounds, it is a new method of air purification developed in recent years. the biggest advantage of photochemical catalysis degradation is green, this method can be available at normal temperature and pressure to degrade formaldehyde and other organic matter into carbon dioxide and water without secondary pollution.Nano-TiO2 have become the most studied photocatalyst due to its stable, non-toxic harmless, superior photochemical catalysis properties [1]. Initially nano-TiO2 powder was used as a photocatalyst, but it’s difficult to recover and easy to wear and tear [2,3]. Later, the TiO2 was used in the form of film loaded on some carriers, such as glass beads [4]. As the photochemical catalysis reaction occurred on the catalyst surface, only the organic matter adsorbed on the catalyst surface can be degraded, so the catalyst was requested that must have a strong adsorption. Combined the adsorption properties of bamboo charcoal and the photochemical catalysis activity of nano-TiO2 together. Made the photocatalyst by loading the nano-TiO2 on bamboo charcoal to degrade organic matter in the air. Nano-TiO2 semiconductor photocatalyst has a strong catalytic oxidation due to the photo generated hole of the surface [5,6],and has a potential application. Some studies have shown that nano-TiO2 photocatalysis activity can be increased by doping certain metal ions [7,8].The aim of our work in this study was to use bamboo charcoal load Ce-doped nano-TiO2 photochemical catalysis oxidation to degrade formaldehyde,and design a multi-ladder structure photoreactor, also prove the availability of the device from the theoretical and experimental."

Jan 1, 2011

By B. J. Jody

Each year, about 11 million tons of metals (ferrous and nonferrous) are recovered in the U.S. from about 10 million discarded automobiles. The recovered metals account for about 75% of the total weight of the discarded vehicles. The balance of the material or shredder residue, which amounts to about 3 million tons annually, is currently landfilled. The residue contains a diversity of potentially recyclable materials, including polyurethane foams, iron oxides, and certain thermoplastics. This paper discusses a process under development at Argonne National Laboratory to separate and recover the recyclable materials from this waste stream. The process consists essentially of two- stages. First, a physical separation is used to recover the foams and the metal oxides, followed by a chemical process to extract certain thermoplastics. The status of the technology is discussed, and the process economics are reviewed.

Jan 1, 1994

By Chu Yong Cheng

The solvent extraction (SX) processes of the three pressure acid leach (PAL) nickel plants in Western Australia have been reviewed. The use of intermediate precipitation, solids/liquid separation and re-leach in the three W A nickel plants make these processes complicated and costly in capital and ?operation. The research work carried out by the SX group at the AJ Parker Cooperative Research Centre for Hydrometallurgy I CSIRO Minerals has led to the development of direct solvent extraction (DSX) processes to recover and purify nickel and cobalt from leach solutions. The simplicity of the process flowsheets and the expected savings in capital and operating costs are the major advantages of the new DSX processes over the reviewed processes. By using a new synergistic organic system in semi-continuous tests with a pilot plant leach solution (after iron precipitation) from BHP-BiIliton Stainless Steel Materials, the metal values (Ni and Co) together with zinc and copper were separated from the major impurities (Mn, Mg and Ca, together with Cl) in the first SX circuit. The co-extracted manganese, magnesium and' calcium were easily scrubbed out. After stripping, the metal values (Ni and Co) together with zinc and copper were concentrated, resulting in a much smaller second SX circuit and equipment in the down stream processes. The extraction and stripping kinetics of the metals with the new synergistic organic solution were very fast. The extraction and stripping almost reached steady state within 0.5 minutes. Semi-continuous test work with a synthetic leach solution, a cobalt pilot plant leach solution from Peko Rehabilitation Project Pty Ltd and a synthetic solution to simulate a concentrated laterite leach solution from BHP-Billiton Stainless Steel Materials showed that manganese, calcium, copper and zinc can be effectively and efficiently separated from nickel, cobalt and magnesium by extraction, scrubbing and stripping. This led to the development of another DSX process using D2EHPA to recover nickel and cobalt from leach solutions.

Jan 1, 2003

By Frederick T. Wallenberger

"Laser assisted chemical vapor deposition (LCVD) is a new containerless fiber process whereby growth of small diameter fibers or microstructures (microsprings, microsolenoids) occurs directly from the vapor phase. The laser beam has a focal point adjusted to coincide with the tip of the growing fiber inside the reaction chamber. Since the growing fiber is not in contact with reactor walls or foreign materials, it is chemically pure, and suitable for optical uses and uses requiring high structural uniformity. Continuous fibers and multifilament yams are possible. The use -of high reaction chamber pressures (1-10 bar) and a small wavelength Nd-YAG laser made it possible to fabricate small diameter fibers at growth rates >1 mm/s. This paper describes the synthesis of single crystal, polycrystalline and amorphous fibers by LCVD, and provides a comprehensive analysis of phase transformations occurring during their fabrication.IntroductionLaser assisted chemical vapor deposition (LCVD) is a new containerless fiber process [1-10] whereby growth of small diameter fibers or microstructures occurs directly from the vapor phase. The laser beam has a focal point adjusted to coincide with the tip of the growing fiber in the reaction chamber (Figure 1). The diameter of the growing fiber corresponds to that of the laser focus. Depending primarily on the laser energy (Le., the temperature at the growing fiber tip), it is possible to obtain single crystal, poly crystalline or amorphous fibers by this method.Since the growing fiber is not in contact with reactor walls or foreign materials, it is chemically pure, and suitable for optical uses and uses requiring high structural uniformity. Laser assisted CVD is a potentially continuous process; continuous fibers and multifilament yams are possible."

Jan 1, 1994

By Takashi Araki

In this work, we have elucidated the two-step oxidative reaction mechanism of 2,4,5-trichlorophenol by adsorbing oxygen atom for oxidative decomposition reaction of 2,4,5-trichlorophenol on oxide catalyst surface using ab initio molecular orbital calculation. In the first oxidation, total energies of reaction products have been shown extremely stabilized at all oxidation positions. This reaction occurs due to charge transfer from benzene ring to adsorbing oxygen atom. As a result, ? bonding of benzene ring are weakened. However, the benzene ring of 2,4,5-trichlorophenol does not perform cleavage reaction. In the second oxidation, the benzene ring of 2,4,5-trichlorophenol can perform cleavage reaction, since the second oxidation obtains larger stabilized energies than the first oxidation.

Jan 1, 2003

By D. Morin

A general study of gold refractory arsenopyrite-pyrite concentrate bioleaching has been carried out including two continuous bioleach testworks at different sizes, namely one at a laboratory scale with a 100 I unit at a 2 kg/d dry solid flowrate and the other at a pilot scale at a 100 kg/d dry solid flowrate. Both tests show a 80% bioleaching of arsenopyrite in about four days of treatment and with the same kinetic. Pyrrhotite is attacked at the earlier stage of the bioleaching but pyrite remains unaffected. The weak potential of oxidation associated with the decomposition of arsenopyrite and the abundance of arsenite leads to a high grade of elemental sulfur in the bioresidue which consumes the major part of the cyanide during the gold recovery. Furthermore. the arsenite and ferrous produced in solution have to be oxidized to obtain a stable precipitate in the waste products and as outlined in previous works of other authors on this subject the addition of iron to obtain a Fe/As molar ratio at least above 3 is necessary. The agitation equipment used in the pilot unit allowed an optimization study calculation for scaling-up the design and power requirements of an industrial installation. For the pretreatment of a gold refractory As high-graded concentrate the reagent cost has the greatest part in the operating cost of the biooxidation step due to the necessary retreatment of the biosolution. In that conditions the power cost is quite marginal. actually it is significant for the treatment of pure pyrite.

Jan 1, 1991

By Jie E. Zhou, Yu U. Wang

"Development of crystallographic texture in polycrystals during templated grain growth process is studied by phase field modeling and computer simulation. To characterize the grain texture development, X-ray diffraction peak intensities are computed for the evolving grain structures as simulated by the phase field model, based on which Lotgering factor is further calculated as a quantitative measurement of uniaxial texturing. While the phase field modeling allows direct comparison between simulated grain structures and experimental microscopy observations, the computational diffraction allows convenient correlation between computer simulation and experimental X-ray diffraction characterization. The latter feature is especially desirable, since microscopy experiments normally require more efforts than X-ray diffraction, and diffraction is usually the preferred choice for material characterization.IntroductionThe properties of individual grains in polycrystals are generally anisotropic, while untextured polycrystalline materials with random grain orientations exhibit isotropic macroscopic properties that are independent of directions. In order to achieve anisotropic response in polycrystals, crystallographic texturing of grains is required [1]. Texture refers to the collective distribution of grain orientations towards preferred orientation in a polycrystal. To develop texture, special processing routes are needed, such as templated grain growth (TGG) for uniaxial texture [2]. TGG has been shown to provide uniaxial texture in wide variety of materials. For example, [001]-textured ferroelectric polycrystalline ceramics have been fabricated by TGG process, which exhibit enhanced piezoelectric properties [3]. Such highly textured polycrystalline materials offer better cost-performance ratio than single crystals. Thus, texture development in polycrystals is of technological importance for material applications.In this computational work, grain texture development in polycrystals during TGG process is studied. Grain structure evolution is simulated by phase field model, X-ray diffraction peak intensities for the evolving grain structures are computed, and Lotgering factor is calculated to quantitatively measure the development of uniaxial texturing. The phase field modeling allows direct comparison between simulated grain structures and experimental microscopy observations using imaging techniques such as scanning electron microscopy or optical microscopy. The computational diffraction allows convenient correlation between computer simulation and experimental X-ray diffraction characterization. The latter feature is especially desirable, because microscopy experiments normally require more efforts than X-ray diffraction, thus diffraction is usually the preferred choice for material characterization."

Jan 1, 2014

By D. W. Hoey

Eight years use of the ISA Process is reviewed and current design and operations described. Nodern Technology used for impurity control and disposal as well as the use of mechanised electrode handling equipment, cell voltage monitoring, cell insulation and an efficient contact bar system are described. Improvements achieved in terms of energy usage and plant productivity are detailed.

Jan 1, 1987

By N. A. Warner

Fundamental studies on the reaction of limestone or dolomite at high temperature with S02 are extended to the realm of large scale primary copper smelting. Whereas flue gas desulfurisation in the electric power utility industry is concerned with S02 concentrations normally less than 0.5 percent, high temperature smelting gases can have S02 levels approaching 100 percent. The reaction involved is very exothermic so proposals are made in this paper for returning the heat generated in sulfur fixation directly back to the copper smelting process. This integration leads to metal production with lower energy requirements than current technology. The anhydrite reaction product can either be disposed of locally with minimum adverse environmental impact or upgraded to a value-added product. It is assumed, of course, that no viable market exists to support sulfuric acid production.

Jan 1, 1996

By Takao Mori

Novel rare earth boron icosahedral compounds are investigated as potential high temperature thermoelectric materials. REB50-type compounds and REB22C2N compounds were synthesized and the thermoelectric properties measured. Seebeck coefficients in excess of 200 V/K are observed at temperatures above 1000 K for the REB50-type compounds. Strikingly, n-type behavior was observed for REB22C2N. Up to now, non-doped B12 icosahedral compounds have all been p-type. The discovery of an n-type compound is extremely important in terms of the potential development of this class of compounds as viable thermoelectric materials. Low thermal conductivities of < 0.03 W/cm/K at room temperature was observed for these rare earth boron cluster compounds.

Jan 1, 2006

By Kazuteru Tozcwa

The oxidation of several sulfide minerals in aqueous ammoniacal solution is discussed thermodynamically. The region in which Cu(NH3)2 4+ is stable has been estimated as a function of pH and concentration of total ammonia, {[NH3) + [NH4)}. In ammonia leaching when copper in sulfides is assumed to be extracted in the form of Cu(NH3)2 which will be rapidly converted to cupric ammine, thermodynamic data predict that such minerals are oxidized readily in the following order, CuS, Cu2S, CuFeS2, ZnS, NiS, Ag2S. This agrees with investigations on ammonia leaching of sulfide minerals, reported previously. The leaching of copper sulfide concentrate has been examined experimentally. Copper in a copper sulfide concentrate, in which the main constituents were chalcopyrite and pyrite, was effective¬ly extracted. The copper extraction was affected by factors such as (1) agitation intensity, (2) oxygen partial pressure, (3) NH3/Cu molar ratio, (4) leaching temperature and (5) addition of ammonium sulfate. From the results obtained in this work, it is concluded that mass transfer of oxygen plays the most important role in ammonia leaching of copper sulfide minerals.

Jan 1, 1976

By Hu Long

Pyrite, as the host mineral in refractory gold ores and concentrates, has been treated by pressure oxidation in sulfuric acid solutions at temperatures above 180°C to liberate gold prior to cyanidation since the 1980&apos;s. However, no data is available on the kinetics of pyrite during acid pressure oxidation over the temperature range of 180 to 230°C which is the range employed by most commercial plants. The dissolution of pyrite (FeS,) in sulfuric acid solution under oxygen pressure was investigated at temperatures ranging from 170 to 230°C. The effects of temperature, particle size, agitation speed, oxygen partial pressure, and pulp density were evaluated. The effects of foreign ion addition and the concentration of sulfuric acid were also examined. The apparent activation energy was estimated to be 42.6 kJ/mol in the temperature range 170 to 230°C. The reaction orders with respect to particle size and oxygen partial pressure were found to be -1.5 and 0.5 at 210°C, respectively. Experimental evidence suggests that the kinetics are limited by the surface chemical reaction initially, and then also to some extent by the diffusion of ferrous ions away from the particle surface.

Jan 1, 1999

By M. Kawakami

In relation to the designing of a new-type blast furnace, the reaction of carbonaceous materials with CO2 is expected to occur at as low temperature as possible. In order to get a highly reaetive carbonaceous material at low temperature, the reaction kinetics was investigated by measuring such quantities as the reaction rate from weight loss, the amount of CO adsorption and specific surface area by BET method. The reaction rates were large in the order of the Bintyo char, metallurgical coke, graphite and glassy carbon. If the rate was converted to the rate per unit area, however, those of the Bintyo char was smaller than that of graphite. Thus, it is suggested that the rate of the Bintyo char is influenced by the pore diffusion of CO2. The rate had a positive relation with the amount of CO adsorption, showing that the rate determining step would be the desorption of CO from the active side on the surface. The rate independent of surface area was derived, combining all the obtained data.

Jan 1, 2003

By Stefan Mutl

By the term sorting one understands the separation of a material mixture into two or several products according to different material characteristics in the preparation technology. The oldest sorting procedure, the handpicking, is less and less used to separate different material mixtures because of the considerable personnel expenditure and the strict hygienic regulations at the workplaces in Europe. In general, the manual assortment is able to solve separation tasks, which could not be solved by machines so far. The picking is one of the most selective processing methods. However, the progress in the computer and sensor engineering today makes the creation of automatic picking devices possible, whose efficiency goes far beyond the possibilities of handpicking. Therefore in the future automatic picking will not only be applied to already common applications like the waste glass assortment by colour, but also to the assortment of complex composed material mixtures e.g. old shreddered cars. Thus, the automatic picking, supported by high performance computer systems and new sensor technology, gains more and more significance within many applications of waste processing. However, in order to apply automatic sorting procedures for different material streams within recycling processes, a substantial research and development need still is existing. The desire of the users is to sort more extensively in order to achieve products with bigger material varieties, In addition, the requirement of the accuracy of recognizing and sorting out of single grains rises, This lecture illustrates the procedure of the hand picking before it was employed in waste processing. Thus, a renaissance of a long forgotten method is happening in terms of today&apos;s state of the art procedure "automatic picking". Possible technologies, fields of application and future potentials of this technology are pointed out.

Jan 1, 2003

By Michael A. Markowitz, Alok Singh

"Molecular self-assembly of phospholipids and other amphipathic molecules offers a versatile approach to form self-organized microstructures in various morphologies. Stabilization of microstructures in specific morphologies by polymerization renders them useful for practical applications in areas ranging from controlled release technology to template mediated synthesis of metals. Our efforts are focussed on the development of polymerizable biomembranes derived from phospholipids, their properties and utility e.g., as stable templates for studying chemistry at the lipid interface. Polymerized vesicles formed from mixtures of 1,2-bis(tricosa-1 O,12-diynoyl)-sn-glycero-3-phosphocholine, 1, with corresponding lipids having phosphohydroxyethanol,2, or -hydroxypropanol,3, headgroups have been used in electroless metal plating of vesicle surface with gold utilizing selective binding of Pd(NH3)4 2 + to 2 or 3. The surface bound palladium ion served as catalyst for metalization. Metalization of polymerized vesicles constructed from charge neutral diacetylenic phosphocholine,1, did not occur using this process. The headgroup structure of the negatively charged phospholipids and the degree of vesicle polymerization had an effect on the stability of the vesicles after metalization. Vesicles formed from a mixture of 1 with polymerizable diacetylenic phosphatidic acid, nonpolymerizable 1,2- dipalmitoyl phosphohydroxyethanol or 1,2-diacyl phosphohydroxyethanol (from soy lecithin) were not stable to metalization process. The metal coating of the vesicles was examined by electron diffraction and revealed that the gold metal on vesicles was polycrystalline and face centered cubic. The results demonstrate the utility of polymerized synthetic membranes as template for easy and efficient synthesis of nanoparticles. IntroductionPhospholipids, synthetic or natural, provide a simple and straight forward route to construct membranes in a variety of morphologies due to their inherent property of selforganization in the presence of water[1]. Vesicles are closed spherical structures comprised of concentric walls made from lipid bilayers. Vesicles are morphologically simple structures with enormous technological potential. Polymerizable phospholipids prepared by incorporating a polymerizable group in the molecules demonstrate physical properties comparable to their non-polymerizable counterparts and have the added virtue of providing enhanced physical and chemical stability to the membranes[2,3]. The size, shape and properties of the organized assemblies are dependent on the lipid structure and the nature of the aqueous environment[4,5]. The headgroup geometry, surface charge density, and spatial arrangement of the phospholipids are known to affect the surface behavior of the lipid membranes, which is evident through their interaction with other molecular (hormones, antigens, antibodies etc) or lomc species. Since phospholipid headgroup structure and charge can be modified either synthetically or by chemical perturbation of the aqueous medium (e.g., pH or ionic strength), phospholipid membrane surfaces offer a potential for developing novel strategies in those areas which involve the use of molecular reactive sites. One such strategy which could be envisioned explores the use of molecularly engineered phospholipid assemblies to design and prepare template structures to regulate formation of ordered materials [6]."

Jan 1, 1994