Search Documents

By Uday B. Pal

In the electrochemical vapor deposition (EVD) process, gaseous cation precursors are passed over one side of a porous substrate, and oxygen is passed on the other side of the substrate. The gases diffuse and react within the porous substrate, and the pores get filled with the desired solid oxide. Subsequent solid state electrochemical transport through the solid oxide in the pores continues the reaction, and the film grows over the porous substrate. The EVD process has been used to deposit lanthanum chromite interconnection films and yttria stabilized zirconia electrolyte films over porous air electrodes. The EVD growth of these solid oxide films is found to be parabolic in nature, which indicates that the solid state transport (diffusion) of ions through the film controls the growth. This solid state transport can be analyzed using Wagner's treatment of the electrochemical transport. Conductivity measurements and the information on the defect structure of the oxide can be combined with the EVD growth rate measurements to calculate the solid state transport properties (transport numbers and partial conductivities) of the rate-controlling minority species in the oxide. Using this approach, the EVD growth of other electronic, mixed conducting and ionic solid oxide films can also be analyzed.

Jan 1, 1992

By F. M. Wang, J. P. Lin, G. Y. Tang, H. C. Zhou, Y. F. Liang, F. Ye

"Fe-6.5%Si alloy is a very excellent soft magnetic material compared with conventional Si steel (Si content ~ 3.5%), especially in high frequencies with reduced iron losses and noises. But it is hard to be fabricated due to its brittleness at room temperature. Dynamic electropulsing is applied to the cold rolled Fe-6.5%Si sheet during tensile deformation. Mechanical and microstructural properties are investigated with different electropulsing and strain rate. It is found that the yield stress decreases and the elongation increases dramatically with the application of dynamic electropulsing. It is indicated that the work hardening could be reduced with the dynamic electropulsing during deformation, which provides a promising way to fabricate this alloy sheet much easier.Introduction Fe-6.5%Si (weight percent, same as below) alloy has more excellent soft magnetic properties compared with conventional silicon steel (Si content ~ 3.5%), such as higher resistivity, higher permeability, near zero magnetostriction, etc. and exhibits much lower core losses and noises [1]. However, Fe-6.5%Si is very brittle at room temperature and hard to be fabricated in strip by conventional hot-cold rolling process [2]. This lack of low-temperature ductility has been generally attributed to structural ordering ofB2 and D03 phases [3]. Several methods have been developed to avoid its brittleness, such as chemical vapor deposition (CVD) [4], rapid quenching [5, 6], dipping and diffusion [7, 8], direct powder rolling (DPR) [9], etc. However, hot-cold rolling method is still of interest for industrial applications. In our previous work, this alloy can be cold rolled after certain thermomechanical process and heat treatment [10-13]. The cold rolled sheet exhibits some extent of ductility [11]. However, side cracks are common for the rolled sheet, it is very necessary to improve the ductility of this alloy by other technical applications."

Jan 1, 2012

By Chen Chen, Wang Yanze, Hong Xin

Furnace superalloy was applied in harsh environment within the erosion of high temperature and oxidizing atmosphere. With plasma powder surfacing technology, iron-based alloy powder was sprayed on the surface of 310S stainless steel to form oxidation layer that increases the oxidation resistance and reduces the cost of materials. With optimum technological parameters, in this paper, oxidation test of 100 hours on iron-based cladding alloy and furnace alloy were carried out at 1200 . The technique of XRF, XRD and EDS were used to characterize composition, oxide morphologies and surface mechanical properties. The results showed that Element composition of cladding layer formed by Plasma powder surfacing was well distributed. Its oxidation weight gain rate of 100 hours was 0.4552g/m2h, belonged to antioxidant level. The oxidation weight gain rate of furnace alloy was 1.4617g/m2h, belonged time-antioxidant level. And on the mechanical comparison test, surfacing alloy is relatively excellent than furnace alloy.

Jan 1, 2016

By Haotian Xue

A new process to extracted antimony directly from stibnite concentrate by reductive sulfur-fixation smelting in sodium molten salt has been presented. The influences of sodium salt content and composition, ferric oxide addition, temperature and time was investigated, respectively. The optimum conditions was determined as follows: W????: ??concentrate=40%, W??alt: ????concentrate =88.75%, WFe2O3 :Wconcentrate =55.13%, W??aCl: ????alt=40%, 1123K, 1h. Under above-mentioned optimum conditions, the average direct recovery ratio of antimony can reach 91.48%, and the main chemical composition of obtained crude antimony is Sb 94.31%, Fe 4.436%, Pb 0.502%, Au 0.0236%. In comparison to traditional antimony pyrometallurgical process, the smelting temperature of present process is reduced from 1423~1473K to 1123~1173K. During the smelting operation, SO2 emision can be avoided completely due to sulfur-fixation as FeS. Furthermore , S0 can be obtained when the molten slag is handled by water leaching with conditions of 323K, L/S=5/1, 2h.

Jan 1, 2014

By R J. Singh, E. Z. Chacko, Devilal, S. K. Jha, Rina Sahu, Sheshank Shekhar

"Breakouts are one of the biggest problems encountered during continuous casting of steel billets. Billets get cracked locally or break completely in two parts during solidification causing the liquid part of the partially solidified billet to empty inside the cooling chamber. Proper control of important parameters is necessary to avoid break outs during continuous casting. In the present work, the nature of the break outs at a billet caster at Tata Steel was studied. Data analysis was also done for certain casting parameters and the Sulphur tracer test was conducted to understand solidification in the mould. It was found that to reduce the occurrence of break outs, it was necessary to tune the operations based on the grade being cast and the design of the mould tube being used.IntroductionA break out during the continuous casting process is a rupture of the partially solidified shell inside the secondary cooling chamber, causing the contained liquid steel to spill out. In the mid 1970s while continuous casting technology was still in early stage of development, causes of breakouts was not well understood. Today, with technological development much has been understood about breakouts but, most of the understanding has been in the slab casting process wherein due to the higher level of instrumentation, a lot of information has been gained. In billet casting however, due to the geometry of the mould housing with the tube mould, multiplied by the complexity of the multiple strands, instrumentation has not been used and obtaining data for analysis has been difficult.Breakouts at billet casters are still the main hindrances to production. A break out results in a loss in production since the strand which has had a break out is now not available to produce and thus a six strand caster would be reduced to a five strand caster, increasing the time for casting the same tonnage. Additionally extra set up time is required as more often than not a mould change is required in order to have the strand casting again."

Jan 1, 2014

By L. Béjar-Gómez

The aim of this research work is to study and characterize the precipitates in structural microalloyed steel by transmission electron microscopy and analysis by low resolution. Microalloyed steel with niobium was produced by casting in an electrical induction oven of 25 Kg capacity. Carbon content in steel was less than 0.1 % and 0.036% of niobium. Steel was processed thermomechanically; reheated to 1250 °C and hot rolled on a laboratory mill to a 13.0 mm thick plate with a finish rolling temperature of 900ºC and a thickness reduction of 80% . This work shows what precipitates are present in steel, the type of precipitates and their morphology. Analysis by transmission electron microscopy of low resolution was applied to obtain the chemical analysis of precipitates and the matrix. Spectroscopy of dispersive energy (STEM - EDS) was applied to obtain the element profile of precipitates. Particles of precipitates of NbC were found; with cubic morphology and size from 70 to 130 nm, circular morphology and size from 10 to 70 nm, polygonal morphology and size from 10 to 80 nm.

Jan 1, 2006

By Johan Sundström

Anhydrous DyC13 was prepared by dehydration of DyCl3?6H20 in a fluidized bed using both batch- wise and continuous feeding. A gas mixture with varied composition of argon and HCl was used. The productivity was high, reaching values of 0.25 mol H20/m2-st during the reaction step 6- 1 and 0.062 mol H2O/m2.s during the reaction step 1-0. The product was free from hydrolytic compounds, such as DyOCI, if control of inlet gas composition versus temperature was achieved. From the results of various experiments, some relations between HCI-concentration and temperature in order to avoid hydrolysis have been deduced. The fluidization process efficiency decreases drastically after the dehydration has proceeded down to about 10 mol% of remaining water. Therefore, in a final treatment the last traces of water were removed by slowly purging gas through a packed bed. The water content could thereby be reduced to less than 1 mol%.

Jan 1, 1997

By Eltefat Ahmadi

Iron-free titanium oxycarbonitride (TiOxCyNz) is a promising feedstock for production of titanium tetrachloride (TiCl4) at low temperatures. In this study, the effects of leaching variables such as temperature, time, particle size of staring material and concentration of the leaching solutions were evaluated on iron removal from nitrided Malaysian ilmenite by Becher process. The nitrided ilmenite was prepared by isothermal reduction with graphite at 1200 °C for 3 h in H2-N2 atmosphere. The aerated leaching experiments were conducted at 50–90 °C with addition of 0.3–2.0 wt% of NH4Cl catalyst. The highest extent of iron removal (XFe) was obtained at about 96.2% for the sample leached at 90 °C for 7 h with 2.0 wt% NH4Cl. The iron concentrate and titanium oxycarbonitride product were characterized by ICP-OES, XRD, XRF and SEM-EDX analyses. The results indicated that the aeration leaching process was a successful route to prepare low-iron titanium oxycarbonitride.

By Jie Li, Liangxing Jiang, Yexiang Liu, Junfeng Gui, Bo Hong, Xiaocong Zhong, Yanqing Lai, Xiaoying Yu

"Pb-based alloys with Pr and Ag were prepared in vacuum electromagnetic induction furnace. The tensile strength, corrosion rate and anodic potential in sulfate solution were measured, and the experimental data were analyzed according to the metallographic phases of alloys, the micromorphology and composition of their oxide films. The results show that, with the addition of Pr, the ultimate tensile strength and corrosion rate of pure lead were increased, and the anodic potential decreased. The extra addition of Ag can improve the properties of alloy further. Comparing with Pb-Ag0.8 alloy which is widely used in zinc electrowinning industry, the ultimate tensile strength of Pb-Ag0.6-Pr2.0 alloy was increased by 31.75%, the anodic potential under 50mA/cm2 was decreased by 30m V.IntroductionIn zinc electrowinning industry, the Pb-Ag (0.5-1.0 wt.%, 0.8wt.% normally) anode is widely used as an insoluble anode['l. It can meet the basic requirements, but still has several problems such as high oxygen evolution over-potential (about 860mV), unsatisfactory corrosion resistance, lead contamination of the cathode product and high consumption of Ag etc.In order to reduce the energy consumption, enhance the corrosion resistance, improve the product quality and reduce the consumption of Ag (or even dispense with it), much research has been done, mainly focusing on Pb-based alloy anodes and Ti-based coated anodes. Detailed investigations have already been carried out on binary alloys (Pb-Ca and Pb-Co), ternary alloys (Pb-Ag-Ca, Pb-Ag-Ti, Pb-Ag-Sn, Pb-Sr-Sn, and Pb-Ca-Sn) and quaternary alloys (Pb-Ca-Sr-Ag, Pb-Ca-Ce-Ag, and Pb-Ag-Sn-Co)[Z-4l, Although these anodes can effectively reduce the consumption of Ag, only the Pb-Co and Pb-Ag-Sn-Co anodes perform well with regard to reducing the anodic potential. However, their complicated manufacturing conditions restrict further commercial use.Besides its application in nonferrous metal electro-winning industry, Pb-based alloy is also used as grid alloy for lead-acid battery, serving as active materials supporter and current collector. In order to enhance the corrosion resistance and deep-cycling performance, reduce the impedance of the corrosion film, the addition of appropriate rare earth elements into anodic grid alloys has become a research focus. Studies proved that RE can enhance the mechanical strength of grids, inhibit the formation of anodic Pb(II) film on the surface of grids and then reduce the impedance of the film[ 10-12l."

Jan 1, 2013

By Jan Yaozhong

The composition and the possible utilization of Ti bearing blast furnace from a titanomagnetite blast furnace smelter were studied. The slag contained about 20% Ti02 and trace Sc. The mineralogical analysis indicated that Ti in the slag is mainly as perovskite. By means of magnetite separation, the Ti containing phase could not be enriched. An effective hydrometallurgical approach was proposed with sulphuric acid leaching. The method proposed for processing the studied slag renders product Ti02 and SC203. Besides the recovery ofTiO2 and SC2O3' the leaching process yields fine grained residues which can used as additives for making cement.

Jan 1, 1996

By E. B. Zanelato

The process of casting metals and alloys occurs through the fusion of this metal and its subsequent casting into a mold with the dimensions and geometry close to the final piece. Most foundries use sand casting molds for making you. This work aims to characterize and evaluate the foundry sand to allow its use in segments of Civil Engineering, creating a viable destination for a residue is that discarded. The following characterization tests were performer: particle size, chemical analysis, X-ray Diffraction and Density Real grain. For the execution of the test specimens was used to 1:3 cement and sand, and the incorporation of 10% and 20% of the total mass replacing the sand, and the trace reference. The results show that best results in compression and bending tests were obtained by replacing 10 % of common sand for sand casting.

Jan 1, 2015

By S. Bagchi

The LaNi5-xMnx-hydrides have potential applications in cryocooling devices for non-mechanical method to compress hydrogen gas. Thermal aging behavior of LaNi5-xMnx-hydrides of compositions x=0.4 and x=1.5 has been investigated. The hydriding properties of the La1.02Ni4.6Mno.4 alloy do not change significantly after thermal aging at 453K for 260 hours. X-ray diffraction analyses of this aged alloy do not reveal the presence of any new phases but the Bragg peaks become broader. Line profile analyses show anisotropic microstrains with an average <e2>1/2 value of -5x103. Thermal aging of the other hydride, LaNi3.5Mn1.5 hydride, at 623K for 280 hours, showed significant disproportionation; the hydrogen capacity reduced significantly from an H/M value of 0.75 in the activated condition to -0.15 after aging. X-ray diffraction analyses showed disproportionated lanthanum dihydride, metallic Ni, and Mn phases. The Bragg peaks were very broad indicative of microstrains or small crystalline domains.

Jan 1, 1997

By Martin Reyes, Juan Hernández, Julio Cesar Juárez, Isauro Rivera, Ma. de los Ángeles Hernández, Francisco Patiño

The dissolution of Ag contained in metallurgical tailings was studied by adding ions Cu2+ and Zn2+ in S2O3 2- medium. Chemical analysis of mine tailings by cupellation revealed a Ag concentration of 71 g/ton. The XRF and XRD analysis confirmed the preponderance of SiO2 in the mineral matrix. The experimental dissolution process was conducted in alkaline solution using six concentrations of NaOH and five of S2O3 2-, at different temperatures, also using five concentrations of Cu2+ and Zn2+ as a catalyst. The results showed similar values for both systems (96.8% and 97.13%). The ion Cu2+ and Zn2+ increases the dissolution of Ag, and decrease the reaction time of dissolution. Under the conditions used, pH and stirring rate did not affect the dissolution of Ag.

Jan 1, 2015

By Dieter Wanner

Off-gas cleaning from metallurgical? plants, requires in many cases very low dust contents which are, difficult to achieve with conventional scrubbers, even with high energy input. Lurgi has developed a scrubber which improves the separation of the fine dust by electrical charge prior to the scrubbing zone,, An Electrostatic Scrubber has been successfully installed for the off-gas cleaning from slag granulation after a waelz kiln achieving less than l mg/m3 in the clean gas.

Jan 1, 1992

By Onuralp Yiicel, Ozlem Okur, Murat Alkan

"In this study, Co-Cr-Mo alloys were produced using a mixture of Co304, Cr203 and Mo03 powders with Al powders by a Self-propagating high temperature synthesis process. SHS is a process of material synthesis that has revealed a number of reactants combinations capable of much higher energy release than conventional explosives. Al203 is added to the mixture to decrease the adiabatic temperature of the system. The thermodynamic simulations and the calculations of adiabatic temperature were examined with FactSage 6.2. In the SHS experiments, different Co304/ Cr203/Mo03 ratios were examined, and their effects on the metal recovery and alloy compositions were carried out. The samples were characterized by using chemical analysis, XRD, XRF and SEM/EDS techniques.IntroductionSelf Propagating High Temperature Synthesis (SHS) has significant advantages compared to the high technology furnace applications, such as very short processing time, simple operation, low energy requirement and low cost [l, 2]. In a SHS process, the ignition starts the combustion and propagates throughout the reactant mixture yielding the desired product. However, the disadvantages of the process such as inhomogeneous or unreacted products due to undesirable reaction rates needs to be overcome by changing some parameters such as ignition temperature, particle size, additive, atmosphere etc. [3, 4]. This work aims to establish a scientific and engineering background in the production of some cast Co-Cr-Mo master alloys via SHS (Self Propagating High Temperature Synthesis) metallurgy which is attractive process technique regarding fast and low-cost production ability of cast alloys."

Jan 1, 2013

By Toshiyuki Nohira, Eiichi Takeuchi, Tetsuo Oishi, Hideki Ono, Hirokazu Konishi

The Dy-Nd-Pr-Ni alloy sample was prepared by cathodic potentiostatic electrolysis at 0.65 V (vs. Li+/Li) for 1 h using a Ni plate in a molten LiCl-KCl-DyCl3-NdCl3-PrCl3 system at 723 K. The highest mass ratio (Dy/Nd+Pr) in the alloy sample was observed to be 50 at 0.65 V. Anodic potentiostatic electrolysis at 2.20 V for 12 h was conducted using the Nd-Fe-B magnet electrode in a molten LiCl-KCl system. All elements were almost dissolved from the magnet, and the original form of the magnet disintegrated. After anodic potentiostatic electrolysis at 2.20 V, cathodic potentiostatic electrolysis was conducted at 1.00 V for 5 h using a Mo plate in order to remove the dissolved Fe from the bath. Finally, cathodic potentiostatic electrolysis was conducted at 0.65 V for 12 h using a Ni plate. The mass ratio of Dy/Nd in the alloy sample was determined to be about 18.

Jan 1, 2015

By Zhiqiang Han, Anil K. Sachdev, Baicheng Liu, Guomin Han, Alan A. Luo

The growth of precipitate phase ,B-Mg11Al12 in Mg-Al alloy is closely related to interface anisotropy and elastic interaction. The aim of this work is to investigate the effects of the interface anisotropy and elastic interaction on the morphology evolution and growth kinetics of the precipitate. In the work, the precipitation of ,B was studied using phase field modeling. In the model, the chemical free energy of the precipitate and the matrix were obtained via thermodynamic calculation. It is demonstrated that the interface anisotropy results in lath-shaped precipitate and the elastic interaction affects the shape of the end of the precipitate. The interface anisotropy causes uneven growth in different directions and the elastic interaction influences its preferential growth orientation. By combining the interface anisotropy and elastic interaction in the phase field modeling, the results showed that the precipitate phase has a lath-shape with lozenge ends, which is in agreement with experimental observations.

Jan 1, 2013

By Robin D. Rogers

Room temperature ionic liquids (RTIL) can replace certain traditional organic solvents in liquid/liquid extraction of metal ions from aqueous systems. The very low vapor pressure and non-flammable nature of RTIL warrant consideration of these neoteric solvents for new processing technologies which will reduce pollution, Increase safety, and lower costs. Metal ion separations in RTIL, however, will typically require the use of an extractant and research is needed to identify suitable selective extractants which have appreciable solubility in the RTIL and low solubility In the aqueous phase. Choice of extractant should also take into account the toxicity, expense, and disposal of the ligand.

Jan 1, 1999

By Keith M. Axler

This report addresses issues specific to the generation of hydrogen fluoride via reaction of calcium fluoride with sulfuric acid. This process has been established on a commercial scale and is under consideration for treatment of calcium fluoride residues from uranium processing. Magnesium fluoride slags are also available as a product of uranium processing. The technique of using sulfuric acid for the production of hydrogen fluoride from magnesium fluoride is also under consideration as a residue processing scheme. In the current study, thermodynamic modeling was used to investigate these chemical processing systems. The results presented herein reveal information relevant to the selection of processing temperatures and conditions. Details include predicted effects in system composition based on operating temperatures for both the calcium fluoride and the magnesium fluoride systems.

Jan 1, 1996

By Bo Jiang, Jiusan Xiao, Hongmin Zhu, Kai Huang, Shuqiang Jiao

Carbothermal selective reduction of simulative titanium slag and various titanium raw materials were presented and SiO2 was found to be partially reduced, forming a series of Fe-Si alloys during the process. Thermodynamic analysis of the selective reduction between TiO2 and SiO2 was performed using HSC 6.0 software, then a series of equilibrium experiments were designed and presented. The activity of Si reduced from SiO2 was affected by the presence of Fe reduced from FeOx and the generation of Fe-Si alloys, promoting the reduction of SiO2 in the whole process. The results of experiment are in great accordance with the calculated data obtained from thermodynamic analysis.

Jan 1, 2016