Search Documents

By René Winand

Due to chemical and electrochemical behavior of the most common additives in copper electrorefining i.e. gelatine, thiourea and chloride ions, it is essential to simulate as far as possible true industrial practice while performing laboratory experiments. The three additives must be studied simultaneously, and added continuously to the electrorefining cell. Ratio electrolyte volume to cathode area; ratio bleed flow to cathode area; hydrodynamic conditions; residence time of electrolyte in the cell; current density; electrolyte and soluble anode must be as near as possible to industrial ones. Experiments performed in the author's laboratory show that under these conditions, reproducible results can be obtained at normal industrial current density and at high current density as well. Problems are however still encountered when developing a sensor for additives monitoring, due to electrolyte redox potential and to substrate influenced thin layer deposition.

Jan 1, 1995

By J. -S. Park, H. -S. Jeon

This study has been carried out to develop a relatively simple hydrometallurgical process for recovering nickel as nickel sulfate from the spent nickel-cadmium battery residue in which cadmium was removed by vacuum distillation. This residue is composed of 36 % nickel, 20 % iron, and other metals such as cobalt. First, crushing and selective classification were performed to separate iron to produce a nickel-rich product (over 40 % nickel). This product was dissolved in sulfuric acid to obtain a nickel sulfate solution. During the dissolution, nitric acid and air were added to the system to enhance the iron oxidation reaction rate. The free acid remaining in the dissolved solution was neutralized by adding nickel carbonate. Iron was precipitated as iron hydroxide and removed from the solution. The nickel sulfate solution was then fed to a vacuum evaporator to concentrate the solution by evaporation of water and crystallized at around 45°C to obtain nickel sulfate hexahydrate. A recrystallization process could remove other impurities such as zinc and manganese.

Jan 1, 2000

By C. M. F. Vieira

Crushed fired brick waste, known as grog, screened at two different particle size, 840 (20 mesh) and 180 µm (80 mesh), was used in mixtures with clayey body to make typical red ceramics for bricks. The effect of the grog addition up to 20 wt.% on the properties of bricks fired at 700oC was evaluated. The results indicated that both the particle size and the amount of grog addition changed the fired properties of the clayey body. Additions above 5 wt.% of grog, with a coarser particle size, decreased the mechanical strength of both the dry body and the fired ceramic pieces. By contrast, grog with a finer particle size may be used up to 10% wt. without deteriorate the properties and corresponding microstructure of the clayey body.

Jan 1, 2009

By Adriana de Aquino Soeiro da Silva, Joao Alves Sampaioa, Luiz Carlos Bertolino, Francisco Manoel Garrido, Marta Eloisa Medeiros

"Brazil has a large agricultural potential and its production success is related to the chemicaland physical soil characteristics. Therefore, the demand in the use of a great quantity offertilizers to compensate the low amount of nutrients in the soil includes about 40% of foodproduction costs. In order to develop economical alternatives to traditional fertilizers, rockswith potential use in agriculture will be studied. In this work the potassium rock, a greensandslate, will be chemically and structurally characterized for the development of a potassiumthermophosphate. This alternative fertilizer will be obtained based on a fusion of a ponderedmixture of potassium, magnesium and phosphate rocks to be applied in the Brazilianagriculture. Preliminary characterization results indicate that the greensand slate presents ahigh percentage of glauconite, quartz and micas.Keywords: Potassium thermophosphate, alternative fertilizers, greensand slate.IntroductionBrazil has a great agricultural potential and its production success is closely related to thesoil's chemical and physical characteristics. However, the country's soils present lownutrients content and high acidity due to weather conditions. Thus, the use of a high amountof fertilizers makes up for the soils' lack of nutrients and accounts for 40% of food productioncosts. Therefore, research on obtaining new alternative fertilizers is a constant worry due tothe increase on food demand [ 1].The lack of raw material for the preparation of NPK fertilizers in Brazil is a concern and theissue of potassium fertilizers a priority. Such a fact is because in 2008 only 608.000 tons ofKCl were produced, corresponding to just 10% of the Brazilian necessity. Thus, the use ofrocks as agricultural nutrients can contribute to reduce the need for industrial fertilizers.This way, the development of a new agricultural raw material originated from a rock thatalready exists in the country's soil is of great importance for the mineral and agriculturalsectors."

Jan 1, 2011

By Shengli Wu, Juan Zhu, Wei Huang, Xinliang Liu, Kaiping Du, Kaifa Zhang

Based on the furnace burden of high content of Al2O3, the process of softening and melting and the characteristic of primary slag were studied with the increase of MgO content in the sinter and adding some MgO into the pellet. The results showed that the content of MgO in the primary slag increased with the increase of MgO in the sinter and pellet. Meanwhile, the permeability of the furnace burden was improved because of low viscosity of high MgO primary slag. Compared with the increase of MgO content in the sinter, the increase of MgO content in the pellet can improved the softening and melting characteristic of the comprehensive furnace burden more effectively. More Mg-bearing pellet should be chosen in the comprehensive furnace burden for the purpose of improvement the fluidity of primary slag and the permeability of the furnace burden in the burden of high Al2O3 content.

Jan 1, 2015

By J. K. S. Tee

Using a novel method, zinc has been selectively removed from galvanized steel scrap on a laboratory scale. The separation is based on thermodynamic principles: during chlorination in air-chlorine (10:l) mixtures at 800 OC, zinc forms a volatile product (zinc chloride) while iron does not chlorinate as its oxides are more stable than the respective chlorides. As much as 92 % of zinc is removed from the surface of steel within 10 minutes. This process overcomes tedious and costly preparatory stages associated with leaching - electrowinning methods.

Jan 1, 1999

By Wang Jia, Chai Li-yuan, Zhang Jin-Long, Peng Bing, Zhang Qiang

"Electrolytic manganese dioxide (EMD) residue was mixed with shale and fly ash as the main materials to make solidification/sintering brick for the utilization of the residue from EMD production. The effects of sintering temperature, sintering time, solid waste content and cooling process on its mechanical properties and toxic elements solidification were investigated according to compressive strength and leaching toxicity. The results showed that the calcined residue had capability of solidifying toxic metals and exhibited perfect strength after treated in the optimal parameters of EMD residue below 50%, temperature at 1000-1100°C, time3-5h, and semi-quenched at 600°C1 InstructionSolid clay-brick holds the leading position among building materials for a very long time in China. The traditional technique of making clay-brick has the drawbacks of backward process, simple facilities and single product. Since Chinese Reform and Opening-up, urban-rural construction and real estate have been booming with the rapidly development of national economy and science technology. The problems of ruining fertile land, environment contamination and high energy consumption in the traditional technique of clay-brick making have not been solved yet. On the other hand, more than 7 billion tons of industrial wastes are accumulated over years which occupies over 6.7 million hectares filed and causes serious environmental problems[1-31. Strategy present in ""The Chinese Agenda of the 21st Century"" required the production of wall materials less energy conservation, land saving and waste recycling.Coal gangue[4-9l, fly ash[I0- 13l, sludge from waste water treatment and tailings of gypsum, pyrite, copper mine, high silicon containing iron, asbestos and ects [l4-lSJ are the solid wastes used for brick making around the world. There are two kinds of process for brick making, high temperature sintering and low temperature steam curing[19•201. Although the technology of two brick making made great progress and got widely application in construction field, no precedent for preparing sintering-bricks with EMD residue as materials occurred in China because of its complicated processing technics and lack of sufficient practical experience to guarantee the bricks' quality.In this study, EMD residue was mixed with shale and fly ash as the main materials to make solidification/sintering brick. The effects of sintering temperature, sintering time, solid waste content and cooling process on its mechanical properties and toxic elements solidification were investigated according to compressive strength and leaching toxicity."

Jan 1, 2011

By C. Lupi

"The energy consumption of copper production by electrowinning, generally represents more than 1/4 of the total energy requirement in hydrometallurgical traditional process (roasting, leaching, purification and electrowinning). The considerable saving can be achieved just in this step that requires about 2.2 kWhlkg of the produced copper. To save energy the cell voltage, or more appropriately its anodic component, can be reduced: that is because the anodic voltage represents the main component of cell voltage and so it is largely responsible for the excessive energy consumption in copper sulphate electrowinning.In this work some ways are studied to lower the anodic voltage. First the cobalt ions were added to the sulphate solution in order to study the catalytic effect on oxygen discharge. Then lead alloys anodes (Pb-Ag, Pb-Sb-Ag and Pb-Ca) were used to promote a better oxygen evolution as a result of a different anodic surface. Their behaviour was compared with the PbSb traditional ones. Finally, as already pointed out by several authors for zinc electrowinning, ethylene glycol was employed as anodic depolariser in order to verify its effectiveness in the case of copper electrowinning. By combining all the above-mentioned ways, energy saving ranging from 20% to 27% is achieved.All the tests were carried out on a laboratory pilot-plant for long time to simulate the industrial conditions. The obtained copper deposits were observed by SEM to highlight their morphology."

Jan 1, 1997

By Larry G. Twidwell, Jannette L. Chorney, Bryce D. Ruffier, Katelyn M. Lyons, Daniel W. Gaede, Ryan J. Foy, Jerome P. Downey

The Army Research Laboratory (ARL) has an interest in the recovery and processing of rare earth elements. At Montana Tech, elevated temperature chlorination of rare earth oxides is presently being investigated as a potential methods leading to the selective separation and recovery of rare earth elements from mineral ores and concentrates. After preliminary evaluation, ytterbium oxide was selected as a representative surrogate material for more extensive chlorination studies. Methods used to determine the conversion and recovery include X-ray diffraction (XRD) and inductively coupled plasma (ICP) analysis. These data have been used to establish and confirm process conditions that consistently yield high conversion efficiencies. Based on the promising results, further experimentation is underway to ascertain the metallurgical response of other rare earth oxides and carbonates to the roasting process. The end goal is to create a robust process for industrial application that has greater efficiency and reduced costs as compared to current practice.

Jan 1, 2015

By Jorge Alberto Soares Tenório, Romano Espinosa, Felipe Fardin Grillo, José Roberto de Oliveira, Denise Crocce

"The aim of this work was evaluation of the recovery of Zn and Fe of the EAFD added to the hot metal in the form of briquette at temperature of 1500°C. The EAFD was agglomerated by cold briquetting and introduced in the hot metal. This study utilized a bench-scale equipment to melt, during this process to kept a flow rate of inert gas above the bath. Were collected periodically metal samples and the samples were analyzed for determination of the content of total silicon and carbon by chemical analysis. Zinc oxide, zinc ferrite and other oxides were reduced and were volatized and collected by a cleaning system of dust (baghouse) located on top of the oven. More than 98% of iron were recovered from EAFD during the test. It was possible to produce a dust containing about 68% zinc by means of adding of EAFD.IntroductionIn the first semester of 2010, steel production was about 706 million tons, 27.9 % more than in the first half of 2009. Not a significantly increase if 2010 data is compared with the first semester of 2007 (only 7.2 % higher), before the world’s economic crises. Steel production is divided into two main routes. The first one, and most used, is the Basic Oxygen Furnace Process (BOF process), which in 2008 accounted for approximately 67.1 % of steel production. The second route is carried out in the Electric Arc Furnace (EAF) that in 2008 represented 30.6 % [1 ].Electric arc furnace dust (EAFD) is a solid waste generated during the steel making process. It is classi?ed according to NBR 10004 as dangerous solid waste-class I, because the elements Pb e Cd leach in water exceeding the maximum limits permitted by the NBR 10004 [2 ]."

Jan 1, 2012

By P. J. Uggowitzer, H. Kaufmann

"New Rheocasting is a novel route of semi-solid casting, in which the globular semi-solid precursor material is produced by controlled cooling of only slightly superheated melts in conventional steel crucibles. The resulting semi-solid slugs are placed into the sleeve of a vertical Squeeze Casting Machine and then filled into steel dies. Solidification occurs under hydraulic pressures up to 100 MPa Due to the reduced cost of precursor material, reduced investment cost and easier recycling, the New Rheocasting process offers cost reductions of up to 25% over conventional semi-solid casting · routes. The New Rheocast products are pore free, pressure tight, weldable and heat treatable castings.In the present work the New Rheocasting Process is introduced and the influence of heat treatment on mechanical properties of the New Rheocast alloy A356 is discussed.The alloy A356 is cast under ideal New Rheocasting conditions into a step die on an UBE HVSC 350 Squeeze Casting machine. As-east, TS and T6 heat treatment conditions with variations in solutionizing and aging time/temperature parameters are applied and the samples are tested by tensile testing. Alternatively, the same heat treatment conditions are applied to conventional Squeeze Casting parts and compared with New Rheocasting.Questions of potential cost savings due to modified heat treatment conditions are also addressed in this paper."

Jan 1, 2000

By Mansoor Barati, Leili Tafaghodi Khajavi

"This study involves employing solvent refining as a purification process in which silicon recrystallization takes place from an iron-silicon melt. It is believed that iron will act as the impurity “getter” and purified silicon crystals will grow from the alloy melt, while the impurities are segregated to the liquid alloy. Phosphorous is a problematic impurity to remove since its segregation coefficient in pure silicon is relatively large. To assess the feasibility and efficiency of phosphorous removal through solvent refining, it is critical to study its equilibrium distribution between solid Si and the Fe–Si alloy phase.The distribution of phosphorous between solid silicon and iron-silicon melt at 1210-1310 °C was measured to evaluate the impurity removal potential of each alloy. Interaction parameter between phosphorous and iron was calculated by varying the concentration of phosphorous in silicon.IntroductionAmong various semiconductor materials for manufacture of solar cells, silicon accounts for over 90 percent of today's PV materials [1, 2].The major challenge in producing solar silicon that operates efficiently is to meet purity level requirement through a cost efficient route. Silicon solar cells can play a significant role in answering the world's need for energy if cost reductions can be achieved through manufacturing process. Considerable effort has been made to replace the expensive, complex vapor-phase purification by a simpler and less costly process. One of the refining approaches that have attracted wide research interests is producing low-cost solar grade silicon by purification of metallurgical grade silicon. Since metallurgical processes are selective in removing impurities, a combination of various purification processes can be used to reduce the impurity level in silicon. Considering different thermodynamic characteristics of impurities, each refining step is responsible for lowering specific impurities."

Jan 1, 2012

By Goran Vukovic

The use of gas purging plugs in the copper industry is a widely used practice. They provide substantial improvements especially in anode refining furnaces, where savings in process time and energy are obtained as well as refractory wear and buildups inside the furnace are minimized. The newly developed system, enables purging plugs to be implemented in both stationary and tilting furnaces, is in operation in vessels on three continents. An additional advantage in these furnaces above all other benefits is the significantly improved melting rate. This innovative and patented gas purging system consists of a purging plug cooling device and a slidable, cooled piping system. It provides compensation for any thermal expansion in the furnace lining and minimizes the risk of undesirable copper infiltration. User experiences and results of this widely used system are reported in this paper.

Jan 1, 2014

By Yuanpei LAN, Minren XU, Deliang NIU, Zhu WANG, Qingcai Liu, Shan Ren

Removal of gas is the major function of RH degasser. To optimize the RH refining craft in Chongqing Iron and Steel Co. Ltd, the degassing effect of RH degasser at different degrees of vacuum was investigated using a vacuum induction furnace. In addition, the effect of processing time on the gas content dissolved in molten steel was also studied. The results showed that degree of vacuum was one of the important factors that determined the degassing efficiency in RH refining process. High vacuum degree is helpful in the removal of gas, especially in the removal of [H] dissolved in molten steel. The processing time could be reduced from 25-30 min to 15 minutes and gas content could also meet the demand of RH refining

Jan 1, 2015

By John L. Sundstrom

Complete systems were designed -and are in operation to recycle the effluent streams and to remove impurities from tankhouse. electrolyte, Heavy em¬phasis was placed on making usable products from as many streams as poss¬ible at minimum capital and operating costs. Almost complete recycling: and reuse of water and sulfuric acid were paramount. Techniques used in-clude solvent extraction - electrowinning, evaporation - crystallization and filtration.

Jan 1, 1992

By Yapeng Zhang, Zhiwen Shi, Chaoquan Yao, Fei Wang, Xinyu Li, Jianliang Zhang

A great deal of iron ores which have special elements have been applied in the sintering process with the decreasing of high-grade quality iron ores resources. In this paper, the laterite nickel ores were added into three different kinds of iron ores respectively to make liquid phase formation research by software of Factsage and high temperature characteristic sintering experiments. The results showed that the adding proportion of laterite nickel ores should be less than 15% when the high temperature properties of the mixing ores were well. Increasing the mixing ration of laterite nickel ores in the sintering blending would play an important role in the reduction of the sintering cost.

Jan 1, 2015

By K. A. Brunk

Newmont's research, operations, history and experience with pre-treatment of preg-robbing carbonaceous ores are described, with emphasis on the chemistry, physics and kinetics of chlorine treatment. Present operations, control strategy and projected changes are also described, including a summary of the adsorption of chlorine into pulps and off-gas scrubbing. Conditions of chlorination have been optimized by the use of Eh-pH diagrams of the gold-chlorine-water system, and have resulted in significant increases in gold recoveries and decreases in chlorine consumptions.

Jan 1, 1987

By Mingming Zhang, Mallikharjuna R. Bogala, Ramana G. Reddy

Steelmaking desulfurization slag samples were characterized using chemical, X-ray diffraction (XRD), scanning electron microscopy (SEM) and energy dispersive spectrometry (EDS) methods. The objective of this work is to investigate the occurrence of sulfur and phosphorus components in the slag samples and to identify their origin and associations with the iron phases. Thermodynamic calculations results confirm the presence of phosphorus and sulfur components in the slag sample at high temperatures (1400 to 1800oC). The main constituents of slag include Ca3SiO5 (28.1%), MgO (9.31%), Ca3(PO4)2 (9.18%), CaS (8.39%) and CaO (5.68%). The major phosphorus and sulfur components of the slag are Ca3PO4 (99.2%) and CaS (79.3%) respectively. Characterization studies indicate the presence of microparticles of different sizes and shapes in the slag sample. Elemental analysis of these particles confirm the presence of major elements (O, Mg, Al, Si, S, Ca and Fe) in the slag sample.

Jan 1, 2015

By Steve Lloyd, Ryan J. Foy, Brandon Steinborn, Jerome P. Downey

Research was performed to evaluate copper and silver extraction from samples of bornite flotation concentrate. Sulfation roasting experiments were performed in a rotary tube furnace, a fluidized bed reactor, and a static bed muffle furnace. Roasting was plagued with rapid, lowtemperature calcine sintering, apparently related to the presence of organic matter in the concentrate. Calcine entered a weak acid leaching process to remove copper, and silver was extracted from the weak acid leach residue in a ferric chloride and hydrochloric acid solution. Copper extraction efficiencies in excess of 90% were attained in the weak acid leach while 90% silver extraction was achieved in the ferric chloride leach, along with copper and lead extractions as high as 93% and 99% respectively. The two-stage leaching process resulted in overall extraction efficiencies of 99% copper and 90% silver.

Jan 1, 2015

By Marcos Aurélio S. Costa, Nilton F. Nagem, Andreia B. Henriques, Herman S. Mansur, Alexandra A. P. Mansur, Antonio E. C. Peres, Valeria G. Silva

The superfine material generated in the Bayer process was used in one innovatively way as a precursor to geopolymerization techniques because of the presence of Gibbsite. Gibbsite can play a role in system adjustment because of the SiO2/Al2O3 ratio. Furthermore in the geopolymeric system it was studied the influenceof the additives such as kaolin, metakaolin and sodium trisilicate in an alkaline media. Others conditions to form the geopolymer were also evaluated such as solid/liquid ratio, SiO2/Al2O3 ratio and total alkaline. The raw materials and geopolymeric products were characterized by several techniques e.g. XRD, DSC, FTIR and SEM. Through the FTIR technique it was observed an increase in intensity and bandwidth in the region centered at 1010 cm-1, which is related to the asymmetric vibration Si(Al)-O, this is an indicating of the possible geopolymer formation This broadening of the band promotes a relative disappearance (overlapping) peaks at 965 and 935 cm-1 associated with raw material (ESPDust).

Jan 1, 2015