Search Documents

By Wu Liu

A modified falling ball technique for measuring the viscosity of liquids is described. It consists of recording the weight vs. time of a crucible holding the liquid of unknown viscosity, as a solid ball, or liquid drop, is let to fall through the liquid. This method does not require measurements at constant terminal velocity, as the conventional falling ball technique. Also, measurements do not depend on visual observation, which is not possible in opaque liquids or containers. The effect of process parameters on the utility of this method and its potential application to liquid systems of metallurgical interest were analyzed theoretically. The paper also com- pares the gravimetric method to the conventional falling ball technique for measuring viscosity.

Jan 1, 1992

By Y. Ide, K. Kishitake

It is expected that an Al-Cr-N composite nitride film may have a higher resistance to oxidation at elevated temperatures than the well-known Ti-Al-N films. The formation conditions of Al-Cr-N films by a de reactive sputtering method and their properties were studied in this study. The films characterized with respect to their high temperature properties such as chemical composition, crystal structure, microhardness, wear and· friction. The crystal structure of the Al-Cr-N films changed from hexagonal phase to cubic phase with an increase in Cr content in the films. The resistivity to thermal oxidation of the Al-Cr-N films is superior to that of usual TI-Al-N films. A half of the friction coefficient in the Al-Cr-N film was obtained comparing with that in the ordinary TI-Al-N film at room temperature and the wear rate of Al-Cr-N film was 2 order smaller than that of TI-Al-N film. The Al-Cr-N films show a small friction coefficient at 500°C and then they are recognized to have good tribological characteristics.

Jan 1, 2000

By M. Soltanieh

The liquidus surface? and tie-lines in the nickel-cobalt-sulphur ternary system have been determined between 1<273-1573 K. The experiments were conducted by equlibrating the liquid sulphide with the metallic alloy phase. The liquid sulphide phase was sampled and chemically analyzed. The alloy was analyzed by electrol} microprobe. Combining the present results with the.avai1abl~ literature data, the thermodynamic properties of this system were calculated.

Jan 1, 1998

By T. T. Nguyen, D. R. Gunasegaram, D. Celentano

"Heat transfer rates at the casting-mold interface are believed to be substantially reduced by the formation of an interfacial gap during the course of solidification of aluminum alloys in permanent molds. In the current work, the effect of force-cooling a permanent composite mold on (i) the initiation and growth characteristics of the gap and (ii) interfacial heat transfer rates are studied. Interesting comparisons are made with the case where no cooling is employed. Casting and mold displacements are measured using L VDTs, and the mold is force-cooled by air jets.IntroductionIn a gravity casting situation where an aluminum alloy solidifies in a permanent mold, a gap initiates and grows between the shrinking casting and the expanding mold (1). It is widely believed that the formation of this gap, customarily referred to as an 'air gap', results in a substantial reduction in the heat transfer coefficient at the casting-mold interface (2), and hence is an important factor in solidification studies.The nature of the air gap formation process is thermo-mechanical. The rate of heat loss from the casting first determines the rate of solidification, which, in turn, decides when the gap initiates. The reason for this is the requirement for the solidified casting surface 'skin' to gain sufficient thickness, and hence strength, to be self-supporting. Once the gap initiates, the gap width controls the rate of heat loss from the casting, which, again, determines the rate at which the gap expands."

Jan 1, 1997

By Harald Laux, Stein Tore Johansen

The plunging jet in tapping of steel from converters or electric arc furnaces entrains gas into the steel bath contained in a ladle. Gas entrainment rate and the effect of the gas on the flow pattern in the ladle are studied by means of Computational Fluid Dynamics CFD. The work focuses on the mathematical modeling. Two numerical methods, one for free-surface flows and one for dispersed multiphase flow are combined. A transport equation for the average bubble diameter that incorporates the effect of coalescence and breakup is presented. Results from computations for one ladle and tapping configuration are shown. Our findings indicate that the gas entrainment rate is affected by the material properties of the liquid in the sense that the material properties determine the shape of the jet. Moreover, bubble sizes in the range of two-orders of magnitude are predicted in the ladle. The dispersed diameter model seems to work well. It showed the expected response to material parameters and the turbulent field. However, the presented analysis is just a first step that was limited due to certain simplifications. In order to obtain better insight in the tapping process improvements of the analysis seem necessary.

Jan 1, 1999

By Pengcheng Li, Wei-Tong Du, Yu Wang, Gang Wen

Carbon dioxide could be utilized as a weak oxidant and a kind of coolant to oxidize elements, meanwhile, helping control the temperature during the converter vanadium extraction process. However, the optimum content of CO2 and the cooling effect of CO2 at low content have not been reported. In this study, experimental research based on the influence of different CO2 contents from 0% to 25% injected to the vanadium-containing hot metal was carried out, as well as contrast experiments of O2-N2 mixed blowing. The results indicated that the optimum content of CO2 was 15%. Under the optimum condition, the oxidation of [C] was the lowest and the oxidation rate of [V] was 96.9%, while the temperature was also lower than the O2-N2 mixed blowing. This paper provide a potential property for utilizing CO2 during the converter vanadium extraction process.

Jan 1, 2016

By S. G. Galbraith

We have used the principles of supramolecular chemistry to develop reagents to transport metal salts. These reagents have separated charged "compartments" which recognize a metal cation and its attendant anion(s). They are easy to manufacture as they are structurally related to the commercial hydroxy-oxime extractants for copper. Efficient protocols for loading and stripping of these extractants depend on the novel feature that they bind the metal salt in a zwitterionic form of the ligand. Transfer of the phenolic protons to the pendant amines generates the charged "compartments" to accommodate the metal cation and its attendant anion(s). This paper focuses on how these types of reagent can be used to recover base metals from sulfate and chloride media in flowsheets in which solvent extraction effects separation and concentration operations, interfacing between conventional leach and electrowin/reduction processes. Work on the development of reagents that have high selectivity for metal chloride/sulfate transport, convenient stripping protocols and appropriate hydrolytic stability will be described.

Jan 1, 2003

By Donald R. Sadoway

Molten salt electrolysis is a proven technology for the extraction of metals -- all the world&apos;s primary aluminum is produced in this manner. The unique properties of molten salts, also make them excellent media in which to treat a variety of forms of waste. Of special .note in this regard is electrolysis in molten oxides, a .concept put forward by. the author, initially as a ."clean technology" for producing primary metal. However, in the context of waste treatment, electroly-sis in molten oxides is a process offering the prospect of changing the. valence of dissolved heavy metals while making pure oxygen gas as the main by-product .Laboratory tests conducted at a temperature of 1550°C on chromate sludge dissolved in an melt composed of Al2O3 and MgO have confirmed electrochemical production of oxygen on a carbon-free anode.

Jan 1, 1996

By G. Glinski, K. A. Pericleous

"Recent advances in new computational modelling techniques such as Lattice-Boltzmann and Dissipative Particle methods offer the prospect of simulating complex fluids such as colloidal and dense suspensions in industrial processes. They are referred to as mesoscopic methods since they lie between molecular dynamics at a microscopic atomistic scale «lO-9m) and traditional macroscopic CFD methods (> 1O-2m). The models behave like a 'coarse-grained' gas consisting of fictitious interacting particles, which are much larger than the real molecules of the actual fluid they represent. Inter-particle forces are set so that the collisions collectively mimic the phenomenological transport properties and flow of the underlying fluid at a macroscopic scale.Much of the developmental work to date has focused on laying theoretical foundations based on thermodynamic and kinetic theory. Successful applications include predictions of macroscopic transport properties of complex fluids and flows in porous media and filters. With the constant increase in computational power, these mesoscopic methods are now sufficiently developed to determine their suitability to simulate complex fluid flows in real industrial processes. This work describes the application of meso scopic methods to the stencil printing of solder pastes in the assembly of electronic components. The aim of this work is to assess the ability of these methods to study the transport mechanisms of individual solder particles suspended in the flux solvent as they enter and fill the micro-apertures of a stencil. This paper demonstrates the coupling of such mesoscopic methods to continuum CFD methods to predict the flow of dense suspensions (i.e. solder paste) in industrial processes."

Jan 1, 2001

By Hua-qing Li

Electromagnetic stirring process effectively improves the casting quality of metals. In this paper, the physical simulation experiment, in which the molten copper is displaced by mercury, was designed. The factory test parameters were determined according the simulated data. The flow behavior of the mercury to be stirred as well as the relations between the microstructure of plate blanks and the current parameters were analyzed. With an appropriate electromagnetic stirring, the inverse segregation of tin for C51900 alloy plant blank reduces from 15 % ~ 30 % to about 5 %, and the proportion of equiaxed grain rises to larger than 30%.

Jan 1, 2009

By Isabel Lázaro

A detailed study has been undertaken into the electrochemistry of the leaching of chalcopyrite in acidic solutions containing ferric ions. Mixed potential measurements have shown that the maximum potential achievable on a chalcopyrite disk in a ferric sulfate medium lies within the so-called passive or prewave region in the anodic behavior of chalcopyrite. The very low current densities due to the anodic oxidation of chalcopyrite at potentials in the region of the mixed potential has made studies of the initial stages of dissolution difficult. However a careful rotating ring-disk electrode (RRDE) study has enabled data to be obtained for the stoichiometry of the initial dissolution reaction to be obtained. Thus, in addition to the detection of soluble iron and copper as products in this potential region, a soluble sulfur species has also been detected. A comparison of the experimental with the expected collection efficiencies of the products on the ring has revealed that this soluble sulfur species is likely to be thiosulfate. The characteristic transient anodic behaviour of chalcopyrite in this potential region has been interpreted in terms of a rate limiting solid-state diffusion process. Thus, extrapolated rates based on reported measured solid-state diffusion coefficients for the mineral at elevated temperatures have been shown to be consistent with the potentiostatic current-time transients. Furthermore, comparative studies of the anodic characteristics of the copper sulfide minerals covellite and bornite has confirmed their greater reactivity in this potential region. The results of this investigation have been combined with a parallel study of the non-oxidative behaviour of chalcopyrite in order to derive a model for the dissolution process which is consistent with other published studies of the electrochemistry and dissolution of the mineral.

Jan 1, 2003

By Dalene Joalet Steenkamp

Excavation of industrial-scale furnaces allows for the systematic study of reaction sequences by identifying the different reaction zones within the furnace. In 2013, Transalloys excavated a 48 MVA submerged arc furnace that was used for silicomanganese production using the ore-based route. The excavation method was reported elsewhere as was observations made in terms of refractory wear and modes of electrical energy dissipation prior to excavation. The paper presented here, reports on the process reaction zones observed during the excavation and subsequent phase chemical analyses of a number of process samples obtained during the excavation. The zones identified were a loose burden zone, a dry coke-bed zone, a wet coke-bed zone, a hard build-up zone, and an alloy zone. The results are compared to observations made in the excavation of an industrial-scale SAF and a pilot-scale SAF in Norway. The presence of the hard build-up zone below one of the electrodes and absence of a slag zone below all three electrodes are unique features of the SAF excavated at Transalloys.

By G. C. Yao

Iron and silicon impurities can form needle and branch shape intermetallie compounds in molten aluminum when there is no manganese. It is difficult to separate them from molten aluminum by electromagnetic separation. The Fe-Si-AI and Fe-Al intermetallic compounds were transformed into Mn-Fe-Si-Al and Mn-Fe-Al compounds by the addition of manganese into molten aluminum. In molten aluminum the morphology of these intermetallic compound particles is lumpish and spherical. Migration resistance of these impurity particles is small, which is beneficial to separation. FeSiMnA4 and FeMnAI6 are paramagnetic. These impurity particles can be moved by magnetic force and can be separated from the molten aluminum.

Jan 1, 2003

By Sedef Pinar Basag, Onuralp Yucel, Ahmet Turan

Niederschlag process is commonly used to produce metallic antimony. The process is a metallothermic process which is conducted in one step for metallic antimony production. Using this method Sb2S3 is mixed with coal and metallic iron and subjected to reduction. During heating, antimony sulfide is decomposed and sulphur combines with iron to form the matte phase. Metallic antimony is collected at the bottom of the crucible. In this study, evaluation of Sb2S3 concentrate, extracted and obtained from West Anatolian Region of Turkey was investigated by using Niederschlag process. The reductant stoichiometry, reduction temperature and duration were carried out in the experiments. Chemical analysis methods by using atomic absorption spectrometry (AAS) and X-ray diffraction spectrometry (XRD) techniques were used for the characterization of the concentrate, metallic nuggets and matte phases.

Jan 1, 2016

By G. C. Yao

Iron and silicon impurities can form needle and branch shape intermetallie compounds in molten aluminum when there is no manganese. It is difficult to separate them from molten aluminum by electromagnetic separation. The Fe-Si-AI and Fe-AI intcrmetallic compounds were transformed into Mn-Fe-Si-AI and Mn-Fe-AI compounds by the addition of manganesc into molten aluminum, In molten aluminum the morphology of these intermetallic compound particles is lumpish and spherical. Migration resistance of these impurity particles is small, which is beneficial to separation. FeSiMnAl4 and FeMnAl6 arc paramagnetic. These impurity particles can be moved by magnetic force and can be separated from the molten aluminum.

Jan 1, 2003

By Orlando C. Rojas

The Potrerillos Smelter commissioned a new El Teniente converter in 1985. As a result of the use of this technology, the Peirce-Smith converters have been processing only high grade matte or white metal. These operational changes resulted in damages to the converter shells, excessive splashing and cold dope generation and very short refractory campaigns. The paper shows the modifications to the tuyere angle, mouth design changes and new techniques for mouth cleaning and gas handling. Operational results up to 1991 are also shown.

Jan 1, 1993

By A. Bilodeau

A new hydrometallurgical process for the production of refined gold and the recovery of palladium and platinum from silver anode slimes has recently been developed and installed at the, CCR Division of Noranda Inc. The process, which facilitates the production of gold of >99.99% purity in the face of increasing palladium receipts comprises; leaching silver anode slimes with hydrochloric acid and hydrogen peroxide at 95°C to solubilize gold, palladium, platinum and base metals while simultaneously rejecting silver as insoluble silver chloride; precipitating gold from the leach solu¬tion with sulphur dioxide gas in two stages to produce a first-stage high purity gold product and a second stage impure gold which is recycled to the leach; washing, melting and casting of the pure gold; precipitation of a palladium-platinum concentrate from the gold-free solution by reduction with sodium formate at pH 4 and 95°C; and neutralization of the palladium precipitation effluent to pH 10 with lime. The results of laboratory and pilot plant studies leading to the adop¬tion of this process are discussed, and data are presented for each of the unit operations. Details of the engineering of the commercial plant are given, and plant start-up experience is described.

Jan 1, 1987

By A. H. Rhoades

The modern polarizing microscope with such accessories as cameras, infrared devices, reflectance and/or transmission photometers, indention hardness, and heating stage is used to characterize coal, coke, and other carbon forms. It allows characterization of coke by-products, such as tars and pitches and their insoluble residues. A useful product of the microscopic approach is the coal petrographic analysis which permits the prediction of coke strength carbonization pressure and volume change. Carbonization tests are expensive, time-consuming and require large amounts of coal. Tests on the coke show it to be strong or weak but give no indication of why. Petrographic analysis requires grams of coal and yields data that indicates why the coal produces coke of a given quality. Small samples from drill cores are sufficient for petrographic analysis. These data are also used to optimize blends for coke production. When coke-plant problems occur, ~he microscope can be used to check the coal blend proportions, as well as for weathered coal. Microscopy is useful in spore correlation work which may be a prerequisite to sound coal reserve estimates. Dispersed vitrinoid reflectance studies are used to determine the degree of organic metamorphism which serves to establish oil and gas deadlines. Tars and pitches are examined microscopically for the amount of normal solids as well as the size of undesirable carry-over solids resulting from pollution abatement practices in coke works. The microscope is also used to study coals for gasification and liquefaction.

Jan 1, 1981

By Masatoshi Ogasawara

Saganoseki smelter & refinery operated two flash smelting furnaces, producing a combined 330,000 metric tons per year (hereinafter mtpy) of copper. [n 1996, however, it successfully shifted to a single fumace operation while maintaining production at the same level. Since then, the production capacity has been further increased to the present 470,000 mtpy by technological improvements. Also, in order to reduce the converter load which represents a bottleneck in efforts to increase production, the matte grade was gradually increased and currently runs at 65 to 66% attaining the low copper content in the slag (hereinafter slag loss) of 0.7 to 0.8%. This &apos; paper introduces some improvements, recent operation results and thermodynamic analyses.

Jan 1, 2003

By William Petrul

Image analysis studies were performed on mill products from laboratory flotation tests of the Zn-Pb ore from the Faro deposit in Yukon, Canada, to determine mineral liberations at specific grinds and to predict recoveries at optimum flotation conditions. The minimum and optimum grinds for liberating sphalerite and galena were predicted from size analysis data for the minerals in large ore pieces, and determined by image analysis studies of the mill products. The determined optimum grinds are about 2 Tyler mesh sizes larger than predicted because sane of the fine grained sphalerite and galena occurs in interstices between coarser grained pyrite and is liberated when the pyrite grains are broken apart. Materials balance calculations were performed on the analyzed values for the liberated and unliberated sphalerite and galenaa to determine their distributions in the mill products. The laboratory flotation tests recovered 74% of the sphalerite and 83% of the galena in Zn and Pb concentrates respectively. The mineral evaluation study indicates that the optimum recovery for sphalerite and galena are 85 and 83% respectively. The company is currently recovering 80% &apos;of the sphalerite and 82% of the galena.

Jan 1, 1989