Search Documents

By M. M. Kim

As-electrogalvanized coatings of pure Zn, Zn-11% Fe, and Zn-18% Fe coatings were characterized in terms of initial crystal structure and surface morphology. Samples were then subjected to heat treatments simulating the paint bake cycle of automobile manufacturers. Surface morphology changes were correlated with the process variables, and crystallo.graphic changes were interpreted by mapping heat treatment routes on the Fe-Zn phase diagram. The morphology of pure zinc electrogalvanized coatings with heat treatment from platelets to smeared platelets. The zn-11% Fe coating changes with heat treatment from tetrahedral nodules to a mixture of round and tetrahedral nodules, with the Zn-:18% Fe coating always having round nodules. Regarding crystal structure, a critical transformation time can be defined at any selected temperature, below which the crystal structure does not change. This temperature is related to iron content.

Jan 1, 1990

By Pamela Bogust, York R. Smith

Photovoltaic (PV) modules are becoming an ever increasingly larger part of our energy portfolio. As more and more PV modules are installed and come on-line, management of end-of-life (EOL) modules becomes an important issue. Currently, management of overburden EOL PV modules is not an issue, but is anticipated to be by 2030. Recovery and recycling of valuable metals in PV modules presents several environmental and economic advantages. In this brief review, we will describe processes for refurbishing and recycling of PV silicon. These processes involve some combination of mechanical, thermal, and chemical processing, all of which all have their oPV) modules have become wn respective challenges. Also, projections of PV module material streams are also highlighted.

Mar 1, 2018

By J. D. Miller

Air-sparged hydrocyclone (ASH) flotation is a high-capacity flotation technology originally developed in the Department of Metallurgical Engineering at the University of Utah for processing mineral resources. However, the technology has been found to be useful in industrial waste processing, in the recycle of secondary resources, and in remediation of environmental problems. For example, areas in which the ASH technology is expected to have potential application include cleaning of waste coal fines, air stripping to remove volatile organics from drinking and process water, water disinfection by ozone or chlorine sparging, dispersed oil removal from water, and contaminated soil remediation. Recently, the ASH has been studied extensively for deinking flotation in the wastepaper recycling industry and has been shown to have excellent efficiency/capacity. In fact, a 20-million-dollar plant has been in operation since June 1992. The ASH technology can provide a specific capacity hundreds of times more than that which can be achieved with conventional flotation equipment and in certain instances is expected to provide superior separation efficiencies when compared to other technologies. The design and principles of ASH flotation are described. Experimental data for fine coal flotation, volatile organics stripping, and deinking flotation for paper recycle are presented and discussed. Finally, other potential areas of application for environmental technology are considered.

Jan 1, 1993

By C. J. Beyke

The U.S. Bureau of Mines has developed a process for the selective recovery of Pb metal from a mixed Pb-Zn concentrate. The concentrate was leached in recycled H2SiF6 at atmospheric pressure and 95° C with a redox potential of 570 mV (Eh). Eighty-five pct of the Pb was selectively leached from the concentrate while 87 pct of the Zn remained in the residue. Pressure leaching of the concentrate was slightly less successful, with 78 pct of the Pb leaching from the concentrate and 80 pct of the Zn remaining in the residue. Pure Pb metal was successfully electrowon from a purified PbSiF6-H2SiF6 solution with 96 pct current efficiency and 0.69-kW.h/kg energy consumption.

Jan 1, 1991

By Akira Kaneda, Nozomu Hasegawa

"In the Mitsubishi Continuous Copper Smelting and Converting Process, slag/matte mixture overflowed from the smelting furnace is separated continuously in an electric furnace (slag cleaning furnace, CL-furnace). In order to improve the separation efficiency of slag and matte and to minimize power consumption, the design and the operating conditions of the CL-fumace should be optimized. In the previous study, the authors developed a mathematical model for simulating phenomena in the CL-furnace. The model consisted of 3 modules, electric field analysis, heat and fluid flow analysis and the particle tracking method. In this study, the model was partially modified: k -E. model was adopted, and the effects of various conditions, such as furnace shape (including accretion) and scale, electrodes configuration, immersion depth of electrodes, and thickness of slag layer, were evaluated. And the optimum design and operating conditions were discussed.IntroductionUnder the recent environmental restriction, advantageous features of the Mitsubishi process have attracted much attention. The process uses 3 furnaces connected by launders. Mixture of matte and slag formed in a smelting furnace flows continuously to a slag cleaning furnace (CL-furnace), where the matte is separated from the slag. The matte is continuously siphoned out to a converting furnace and converted to blister copper. The slag overflowed from the CL-furnace is discarded. Because the slag contains about 0.6 % copper, improving slag/matte separation efficiency and decreasing copper loss make a great profit. Moreover the process requires a large amount of electric energy, so reduction of electric power consumption brings in enormous benefit.The objective of this study is to optimize the design and the operating conditions of the process, especially the CL-furnace. This will be achieved by developing the mathematical model and clarifying relations between the design or the operating conditions and various phenomena in the furnace. Fig. 1 shows an outline of the CL-furnace. The mixture entering through an inlet is separated to slag layer and matte layer . In order to maintain the temperature of the melt at a predetermined level, 6 electrodes are immersed into the lag and Joule's heat is generated by 3-phase alternating current flowing."

Jan 1, 2000

By T. -M. Guo, M. J. Braun

"This paper presents an experimental and numerical study of melt flow near the solid-liquid interface and its effect on the interface curvature in a horizontal unidirectional solidification system with succinonitrile. Melt flow is introduced by increasing the ampoule channel thickness. Visualization techniques are employed to observe the flow field and the solid-liquid interface curvature. A numerical model is also developed to simulate the heat transfer, melt flow and phase change in the system. Quantitative information on the flow and temperature fields is generated. A good agreement is achieved between the experimental observations and model predictions. The results could be used for the study of the effect of the melt flow on interface morphology during solidification.IntroductionClassic unidirectional solidification experiments of transparent alloys are conducted with thin film samples sandwiched between two glass slides to investigate the development of interface morphology during solidification [1]. Samples with small channel thickness are usually used to suppress any melt flow due to natural convection and solidification in the channel would then be in the diffusive regime so that the solidification theory can be significantly simplified [2, 3]. Effects of melt flow, in particular due to natural convection, on solidification have also been studied extensively in those systems with large geometrical dimensions [4-6]. These studies indicate a strong effect of the melt flow on interface curvature during solidification [5, 6]. Only limited efforts were made to address the effect of the melt flow on interface morphology in horizontal unidirectional solidification, in particular for the cases when the channel thickness is not thin enough to suppress completely the natural convection [7]."

Jan 1, 2004

By Jianhua Xin, Min Chen, Cuihuan Huang, Shan Yu, Xiaoao Li, Nan Wang, Guanghao Chen

Copper enrichment behavior in continuously cast slab induced by scale formation after continuous cooling in H2O vapor atmosphere and consecutively in air has been experimentally investigated by combining with SEM-EDS analysis, for the purpose to examine the effects of initial slab surface temperature and contents of copper and nickel. For Slab 1 with copper content of 0.1 percent, no visible copper enrichment is found at scale-substrate interface irrespective of the various scale microstructures formed at different initial slab surface temperatures. For Slab 2 with higher contents of copper and nickel, copper-rich phase accumulates and stays at scalesubstrate interface under the condition of lower initial slab surface temperature; while Cu-rich phase in the porous scale formed at higher initial slab surface temperature is noted with simultaneous Ni-enrichment appearing in front of the steel-scale interface. Both a porous scale and high nickel content work together to provide pores for copper-rich phase migration away from interface and occlude within the scale layer.

Jan 1, 2016

By Akira Yazawa

Experimental results for the distribution ratios of various elements between the slag, matte and/or copper in the silica-saturated copper smelting system were summarized. The experiments were carried out under an oxidative smelting condition with S02 gas flow, and also a reductive smelting condition equilibrating with metallic copper or iron. To evaluate the results thermodynamically, the availability of one atom cation base expression for the constituent compounds is emphasized from both of theoretical and practical standpoints. Both of oxidic and sulfidic dissolutions in slag are postulated for some elements such as copper, nickel and lead., and the experimental results are reasonably explained thermo-dynamically. The results for the mutual solubility between matte and ferrite slag and the distribution of minor elements between liquid copper and ferrite slag are also discussed.

Jan 1, 1983

By J. M. Khodadadi

"A computational study of the effect of thermocapillary convection on melting of a droplet under the influence of an incident uniform heat flux is presented. The computations are based on an iterative, finite-volume numerical procedure using primitive dependent variables, whereby the time-dependent continuity, momentum and energy equations in the spherical coordinate system are solved. During the early periods of the melting process, conduction mode of heat transfer is dominant. As the thermocapillary convection is strengthened due to the growth of the melt zone, melting on the side of the droplet is observed to be much faster in comparison to the conduction-only case. Due to the skewedness of the temperature field, a new recirculating vortex is created which promotes melting within the droplet. The effects of the change in the sign of the surface-tension temperature coefficient on the melting pattern are also investigated.1. IntroductionMelting and solidification of materials are important processes which are encountered in nature and numerous industrial applications. Due to the recent upsurge of interest in such processes as spray casting, space radiators, rapid solidification, purification of materials, containerless processing, etc., there is a need to analyze the transport phenomena of melting and solidification in spherical configurations. Specifically, the effect of thermocapillary convection on the melting of metallic droplets has not been addressed at all. Only a few authors have studied the transport phenomena without phase change in spherical droplets. Oliver and DeWitt [l] worked out a series solution for the thermal and surface-tension-driven flow fields for a droplet experiencing an irradiant energy flux in the microgravity environment. Kudo et al. [2] solved the coupled momentum and energy equations numerically for the same problem without dropping the convective terms. Due to the nonexistence of any previous work on transport phenomena during the thermocapillary-assisted melting of metal droplets, this study was initiated to elucidate the features of the phenomenon."

Jan 1, 1999

By Xiang Zhang, Junjie Liu, Zhibo Tong, Langsha Shao, Guojun Ma

The aqueous mineral carbonation process that leaching alkaline earth metals from industrial residues by ammonium salt and carbonation thereafter is one of the potential technologies for CO2 sequestration. In this paper, the effect of particle size of waste slag on the leaching rate of metals under a microwave field and effect of microwave irradiation on the carbonation process were investigated. It was found that the initial leaching ratio of Ca decline seriously with the particle size of EAF slag increasing, and the Ca leaching ratio is relatively low during 120 min leaching. The lower leaching ratio of Ca with large particle size is due to the existence of a silica product layer produced on the surface of calcium silicates. Moreover, due to the microwave irradiation, the leaching ratio of calcium and the crystallization rate of calcium carbonate increase, though the particle size and distribution range of calcium carbonate reduce.

Mar 1, 2018

By Luciano E. Ramírez, Jesús L. Valenzuela, José R. Parga

"An innovative process for removing copper cyanide complexes including silver and zinc from cyanidation circuits has been developed. The technology was based on the inducing the nucleated precipitation of copper and silver in a tube serpentine reactor, using sodium sulfide as the precipitate and sulfuric acid as pH control. The results showed that pH had a great effect on copper cyanide removal efficiency and the optimum pH was about 3 to 3.5. At this pH value copper cyanide removal efficiency could be achieved above 97 and 99 % ,when influent copper concentration ions were 650 and 900 ppm respectively. In this process (sulphidizaton-acidification-recycle-thickening), the cyanide associated with the copper cyanide complexes is released as HCN gas under weakly acidic conditions, allowing it to be recycled back to the cyanidation process as free cyanide. This system was successfully commercial applied at Minera William in Mexico.IntroductionThe recovery of gold and silver from minerals and concentrates with cyanide is an important hydrometallurgical process, which has been studied for more than 124 years. Patented by MacArthur in 1888 [1], the process relies on the fact that gold dissolves in aerated cyanide solutions to produce the gold cyanide complex. The stoichiometry by wich this reaction occurs is known as the Elsner equation as shown here. Silver is accomplished in the same fashion."

Jan 1, 2012

By Guolin Zheng, Jian Pan, Deqing Zhu, Xianlin Zhou

"In ferronickel production, nickel oxide and part of the iron oxide are reduced to metal by agglomeration and smelting in blast furnace. Due to the physical and chemical properties of the laterite ores, a large fraction of fines is generated during the pre-treatment stages and the strength of agglomeration is weakened, which results in low productivity and bad quality. In this paper, the process of pelletization of nickel laterite was developed, and some parameters to strengthen the pelletization of nickel laterite have been optimized. The results show that the compressive strength of fired nickel laterite pellet can reach over 2000 Newton per pellet while firing at the temperature of 1220 °C~1250 °C in 12 min. The product pellet can be used as high-quality burden for blast furnace to manufacture ferronickel.IntroductionIn recent years, the global stainless steel market was developed exuberantly, which greatly promoted the needs of the basic raw material of stainless steel smelting - metal nickel. Currently nickel sulfide ores are only 40% of global nickel reserves, but offer 60% of all the nickel production. However, with the deficit of resources, the nickel sulfide ore (high grade ore) is depleting, so there is an increasing focus on the utilization of low-grade nickel laterite. Recent research has focused on the wet treatment process to utilize nickel laterite, and less on the use of other technologies [1-8]. The economical and efficient technology relies on the reduction of nickel oxide and part of the iron oxide metal by agglomeration and smelting in blast furnace in China. Some domestic steel companies have adopted this process [9, 10]. Unfortunately a large fraction of fines is generated during the pre-treatment stages and the strength of agglomeration is weakened, which results in low productivity and bad quality of fired pellets. In this study, the process of pelletization of nickel laterite was developed firstly, and some parameters to strengthen the pelletization of nickel laterite have been optimized, and the product pellet can be used to produce stainless steel and ferronickel alloy by blast furnace."

Jan 1, 2011

By K. Yamaguchi, Y. Takeda

"Partial pressure - temperature - composition correlation diagrams of the Ga-As, In-As, Ga-P and In-P systems were contracted based on the obtained experimental data of the phase diagram and thermodynamic properties for the III-V systems. The total vapor pressures of arsenic or phosphorus at melting point of GaAs, InAs, GaP and InP were determined as 101, 10.1, 1510 and 253 kPa, respectively, at the corresponding melting points of 1509, 1211, 1739 and. 1336K , These diagrams are applied to the analysis of the horizontal Bridgman method and the liquid phase epitaxial growth technique. On the other hand, the analysis of the equilibrium state of the. chloride-CVD process was carried out using the data of the Gibbs energy of the compounds obtained by· authors.IntroductionThe group III-V compound semiconductors ate important materials used in optoelectronic liquid high speed electronic device. The crystal growth of the III-V compounds can involve processes that require contact between the solid, liquid and vapour phases at near equilibrium condition. Examples of processes that involve contact between the solid, liquid and vapour phases include bulk crystal growth such as the horizontal Bridgman and the liquid encapsulated Czochralski method and liquid epitaxy, and between the solid and vapor include chemical vapour deposition and molecular beam epitaxy. Therefore, the knowledge of the phase diagram and thermodynamic properties for the III-V binary alloys is essential for the analyses of crystal growth techniques of III-V compounds.For these reasons, a series of different · types calorimetric measurements had been carried out: (1) The heat contents of alloys for the Ga-As, In-As, Ga-P and In-P systems by a drop calorimeter [1;2,3]; (2) the heats of formation of the GaAs, InAs, GaP and InP compounds by a twin solution calorimeter [4]; and (3) the standard entropy of these compounds by an adiabatic calorimeter [5]. Based on the third law method, the Gibbs energies of these compounds were derived from the heat capacity, standard heat of formation and standard entropy data obtained by authors. Integral molar thermodynamic quantities of the liquid III-V .alloys were also determined from combining the heat contents of alloys with standard heat of formation and standard entropy data of the compounds· by applying the thermodynamic analysis method developed by Oelsen [6]. In the present study, the thermodynamic calculations for the crystal growth processes of the III-V compound were carried out using newly experimental data of the phase diagram and thermodynamic .properties measured by authors"

Jan 1, 2000

By Chao Li, Shi Sun, Hongxu Li, Jiaqi Fan, Qi Liu

With the great demand of consumer electronics (CE) and electric vehicles (EV), cobalt has become one of the more scarce energy metals.The recovery of cobalt from a copper converter slag, which contained over 2.4% Co and was accumulated as industrial waste, by reduction-sulfurization smelting was explored. Quantitative analysis of treated slag showed that activated carbon and ferrous sulfide can be used to settle cobalt into matte as Co–Fe alloy. The experiment was carried out at 1673 K with a reducing atmosphere of burning electrode graphite crucible. It was found that the recovery of Co would increase within creased added activated carbon, was unaffected at higher carbon additions, and for low additions of carbon increased at higher FeS additions. Over 95% Co, 99% Cu and 62% Fe could be settled into matte. Preliminary separation of Co from converter slag by pyrometallurgical smelting is proposed.

Mar 1, 2017

By B. Q. Li

A numerical study of the developing fluid flow and thermal aspects during the staning phase of aluminum continuous casting processes is presented. The deforming finite element method, coupled with a quasi-Lagrangian formulation, is used to represent the growth of an ingot and the dynamic fluid flow and thermal behavior that evolves in the growing ingot. The mathematical formulation of the problem and the numerical treatment are discussed. The algorithm solves the free moving nodes as part of total unknowns with an automatic time step control for time integration. This permits an optimal computing efficiency while still keeping the computational errors under control. A selection of the results obtained using the algorithm is presented. The results are concerned with the evolution of fluid flow, temperature and solidification phenomena during a DC round ingot casting process, as it evolves from the beginning of casting operation to a steady state. These results show that the time-varying, complex fluid flow and thermal phenomena during continuous casting processes can be very well represented by the computational algorithm. The results also illustrate that, during the casting process, ~e fluid flow and temperature fields change drastically at the initial stage but evolve slowly afterwards

Jan 1, 1993

By Luben Xie, Lin Hu, Qiang Wang, Min Gan, Tao Jiang, Wenqi Li, Xiaohui Fan, Zhiyuan Yu

"Crystal precipitation behavior of calcium ferrite (CF) during iron ore sintering process along with the effect of cooling rate, SiO2 and Al2O3 on crystalline condensation were studied. The results show that CF, has strong ability of precipitation. The precipitation is barely affected by extenal factors. It begins to precipitate when the liquid phase cools down to about 1200oC. CF could crystallize rapidly at the cooling speed of 150 °C /min. Furthermore, decreasing of the cooling rate favors the development of crystal. Binder phase transformed from CF system to silicate system when SiO2 content was increased to 5~6%, with a constant basicity (R) 2.0. Increasing Al2O3 content could promote the precipitation of CF and the development of crystal.IntroductionCrystalline condensation is the last stage of sinter mineralization. It includes the processes that crystalline substance and amorphous substance precipitate from high temperature solution phase and the consolidation of material when melt cools down. During the crystallization process, minerals precipitate following the order from high to low melting point coupled with the decreases of free energy. Most of binder phase minerals and part of iron oxides crystallize in this process, which have an important influence on mineral composition and microstructure of sinter. They finally determine the sinter strength and metallurgical properties."

Jan 1, 2011

By Mei Yang, Wei Gao, Jian Yang, Qingcai Liu, Wenchang Xi

"TiO2 has been loaded on cordierite porous ceramic to prepare the SCR catalyst carrier by using both APCVD and sol-gel technology. In APCVD method, TiC14 and O 2 were used as reaction precursor. TiC14 was gasified by using N2 as carrier gas which was controlled to 500sccm. Its reaction temperature and reaction time were limited to 773K and 30min respectively. The physical properties, SEM and SEM-EDX of the TiO2-cordierite carrier and the properties of SCR catalysts prepared by these carriers have been tested. The tests showed that TiO2 loaded by APCVD method were of graininess shape and even accumulation. The loading rate of TiO2 and the specific area of carrier sample were increased 114% and 21 % respectively comparing with sol-gel technology. In the result of sol-gel method, the maximal difference of Ti content was 66.92%, while the result of APCVD method was 18.89%. It demonstrated that TiO2 was uniformly attached with the cordierite ceramic by using APCVD method, which would ensure more active ingredients well loaded on the Ti02-cordierite carrier. This difference made the denitrification ratio of catalyst prepared by APCVD method was 8.1 % higher than that of catalyst prepared by sol-gel method.IntroductionIn recent years, the emission of NOx, which were caused by coal-fired power plants, has gotten more and more attention. SCR (selective catalytic reduction) is the most effective technology to DeNOx [ll. The core technology of it is the catalyst. The SCR catalyst usually uses Ti02 as the carrier, and V2O 5 as the active component [2, 3] . However, the thermal stability and mechanical properties of TiO2 carrier are unstable, which would influence the performances of the catalyst. The commercial catalyst generally uses WO3 or MoO3 to promote its heat stability at present [4-7] Besides, TiO2 is expensive. Compared with TiO2, the cordierite is of good thermal stability and lower price. So loading Ti02 on cordierite porous ceramic as carrier to produce SCR catalyst is of good prospects [S, 91 • Currently, TiO2 is usually loaded on cordierite by the sol-gel method. But some research has shown that the sol-gel method easily reduced the loading performances of TiO2, such as distribution, combination, etc. APCVD (atmospheric pressure chemical vapor deposition) has many advantages to preparing TiO2 films, such as high bonding strength, fast reaction rate and so on [l0-13l_ In this paper, TiO2 has been loaded on cordierite porous ceramic to prepare the SCR catalyst carrier by using both APCVD and sol-gel methods. The properties of the carriers prepared by the two processes have also been compared."

Jan 1, 2011

By Thomas F. Nederpel

The production of zinc and zinc-aluminum coated strip can be reasonably accomplished on a single operating unit. However, if the hot dip coating line is equip d with only one mo 7 ten metal holding furnace, it is necessary to transfer liquid metal of different chemistries and reintroduce virgin material to obtain the 18" necessary balance of elements in the bath. Dofasco produces Galvanize and Galvalume on a coating line with a sin le liquid metal furnace and has developed not only an efficient liquid metal trans& system but also an effective means of reutilizing the zinc-aluminum mixtures without detrimental quality affects.

Jan 1, 1992

By A. Martins, L. Goulart, E. Araujo, R. Batista, A. Costa e Silva

Steel cleanness is of great importance to the performance of almost all steel products. From very clean steel for bearings to long products used in civil construction, processing variables – in special those in steelmaking operations- must be properly balanced to achieve adequate cleanness for the desired performance. With the present complexity of steels as alloy systems, it is not efficient nor appropriate to develop these processes on empirical basis alone. Computational thermodynamics can greatly improve process development to achieve the desired cleanness level at reasonable costs. In this work, examples of these calculations and their applications to real steel processing are presented and discussed. The advantages, limitations and areas in which improvement in these calculations is desired are highlighted and discussed.

Jan 1, 2015

By cheng Peng-fei, TANG Hai-yan, guo Xiao-chen, LI Jing-she, Liang Yong-cang, Zhao Baojun

The origin and evolution of non-metallic inclusions for Al-killed casing steel during EAF-LFVD- CC process were studied by industrial tracer experiments. The formations of Al2O3 and MgO·Al2O3 micro- and macro-inclusions from ladle slag were analyzed by theoretical calculations. The results show that micro-inclusions were formed during deoxidation and temperature decreasing in the process of casting, most of the macro-inclusions come from entrapped ladle and mold slags. In addition, most of the Al2O3 formed were modified into 12CaO·7Al2O3 and 3CaO·Al2O3 inclusions which are liquid at steelmaking temperature. MnS cannot be fully modified to CaS and it was only wrapped outside the alumina or calcium aluminate in the form of (Ca,Mn)S with the amount of Ca-Si wire fed during the test.

Jan 1, 2016