Search Documents

By Ying Qin, Shujing Zhu

The characterization of adsorption of natural and composite bentonite in lead aqueous solution has been studied. The results showed that adsorption of both natural and composite bentonites strongly depended on the pH values of the solution. At lower pH values, the mechanisms that govern the adsorption of bentonites were dissolution of crystal structure and competition between the metal ions and the H+. To composite bentonite, the lead ion removal capacity was close to 250 mg/g. At higher pH values, formation of lead hydroxyl species might lead to either participation to the adsorption or precipitation onto the bentonites. Hence, a rapid increase in the equilibrium removal capacity of lead was obtained when pH > 7.0. An increase in the initial lead ion concentration led to the increase in the equilibrium adsorption capacity increased to a certain degree; and then, a plateau was obtained at higher concentrations. As a result, the adsorption performance of composite bentonite was better than the natural bentonite in both physical and chemical changes. The data fitted well with both Langmuir and Freundlich isotherms.

Mar 1, 2017

By Jiangtao Li, Zhongwei Zhao, Xingyu Chen, Xuheng Liu

In tungsten ion-exchange process, excessive sodium impurity enters into ammonium tungstate solution. However, the Na content of the final ammonium paratungstate (APT) product must be strictly controlled. Consequently, it is necessary to remove Na from the ammonium tungstate solution during processing in order to obtain the required purity of APT. In this study, porous Na specific absorbent, Na1+xAlxTi2−x(PO4)3, is used to remove Na from the ammonium tungstate solution. Through experiments, the effect of reagent concentration of Na1+xAlxTi2−x(PO4)3, reaction time, reaction temperature and Na concentration on the Na removal were investigated. The results showed that under optimal reaction conditions of reagent amount of NATP 1.0 times of theoretical amount, reaction temperature 25 °C and reaction time 15 min, the Na removal from commercial (NH4)2WO4 solution can reach 98%. Na1+xAlxTi2−x(PO4)3 has a good applicability to different Na+ concentrations. The obtained APT product reaches the national standard purity of zero level.

Jan 1, 2014

By N. Gopalakrishnana, R. Beccard, S. Lourdudoss, R. Holz, M. Deschler

"Rapid growth of conducting and/or insulating InP, GaAs, Gao.47In0.53As, and GaAs0.6Po.4 on one or more of (001), (110), (111)A, (3ll)A and (3ll)B surfaces by Hydride Vapour Phase Epitaxy (HYPE) is demonstrated. The maximum growth rate of the binaries lies between 12 and 300 µm/hr and of the ternaries between 7 and 170 µm/hr. A simple model is developed to describe the influence of crystallographic orientation on temperature dependent growth rates. The growth rates predicted by the model is compared with the experimental values. Room temperature resistivity of insulating InP:Fe can be as high as 5xl09 ohm cm. Temperature dependent differential resistivity is also analysed. This feasibility of growing conducting and insulating layers rapidly on different orientations is very useful for electronic and optoelectronic devices.IntroductionRecently there is a renewed demand for very thick layers of III-V compound semiconductors for high performance electronic and optoelectronic devices [1]-[2]. Long wavelength high speed lasers that can be modulated up to 30 GHz necessitate epitaxial growth of semi-insulating (SI) layers [3]. There is also an increased interest on the growth of epitaxial layers on surfaces other than (001) surface. Epitaxial growth of these materials on such surfaces is of theoretical importance besides being technologically relevant. These demands led us to focus on the growth of conducting and insulating III-V compounds by Hydride Vapour Phase Epitaxy (HYPE). lnP, GaAs, Gao.471no.s3As on lnP and GaAso.6Po.4 on GaAs were grown as conducting materials using Low Pressure HYPE (LP-HYPE) on (001) 2° off substrates. Gao511no.49P on (001) GaAs substrate and lnP on lnP substrates of (001), (110), (l 11)A, (31l)A and (3 ll)B orientations were grown as semi-insulating materials using Atmospheric Pressure HYPE (AP-HYPE). In this report we present the growth aspects of these materials. We also present a simple model on the growth of InP on substrates of various orientations. The theoretically obtained temperature dependent growth rates are compared with the experimental values. Differential resistivities of semi-insulating lnP grown on substrates of various orientations as a function of temperature are also summarised."

Jan 1, 1998

By Qiu Dingfan

The Slurry Electrowinning Process (SEP) is a new hydrometallurgical method and clean technology, Sulfide ores can be treated by the SEP without S02 emission and the sulfur from the sulfides can be recovered in element form which is easy to stockpile and can be transported at low cost. In a special slurry electrowinning cell one can achieve at the same time the leaching of elements from the feed and the electrowinning of metals from the electrolyte, Because the anode reactions are utilized for leaching of some elements the consumption of the energy is decreased, SEP also has the advantage of separation some elements, It is especially suitable for treatment of complex concentrates containing Pb, Cu, Au, Ag and S, which could hardly be accepted by any smelter. In this work, the behavior of different metals in this process has been studied and it was found that the separation of metals in some minerals is possible through the SEP, Beijing General Research Institute of Mining and Metallurgy (BGRIMM) has studied the possibility of the SEP to treat bismuth concentrates containing S, Be and F in laboratory and pilot-test scale as well as in commercial plants, The commercial plant was set up in 1997, It has been in operation since that time, According to the results of laboratory experiments and pilot- plant test, a new plant to treat complex gold minerals was set up in 1998 and is in operation in 1999

Jan 1, 2003

By Lei Wang, Jianjun Wang, Lingen Luo, Zhengbang Li

Dearsenication in molten steel was studied by adding Ca-Fe Alloy-based arsenic removal agent. In order to improve the utilization rate of Calcium Iron Alloy and improve arsenic removal ratio, [O] is less than 0.0005% and [S] is less than 0.0035%, Al is added into the molten steel. In the processes of adding CaO-Al2O3 based alkalinity slag for arsenic removing in molten steel (initial arsenic content is 0.0080%), arsenic removal ratio reaches 50% when Ca-Fe Alloy addition amount is 18%. During the arsenic removal experiment, adding Rare Earth promotes the arsenic removal reaction and makes the arsenic removal more effectively.

Jan 1, 2015

By Wufeng Jiang, Jiann-Yang Hwang, Suju Hao, Yuzhu Zhang

Lime was made by the calcination of limestone in a high pressure resistance furnace. The lime mineralogical phases and micro-morphologies was characterized by field emission scanning electron microscopy (FE-SEM). The lime activity degree was determined by acid-base titration, and the lime pore distribution was measured by mercury intrusion porosimetry (MIP). The results show that with the increase of calcination pressure, the lime activity degree is increased, and the lime develops a large pore structure. The desulphurization experiments were carried out in the induction melting furnace using active lime with different activity degrees as a desulfurizer. The results show that the desulfurization performance of lime is closely related to the activity degree. There is a strong positive linear relationship between the desulfurization rate and the lime ’s activity degree.

Mar 1, 2018

By Katsunori Yamaguchi

A new technique for the removal of tramp-elements from steel scrap has been required from the viewpoint of saving energy and protection of environment. In order to obtain fundamental information on the removal of copper, tin and zinc from molten iron, the extraction method by using of phase separation in the liquid Fe-Pb-C system was investigated at 1453K A mixture of iron, lead and carbon melted in a carbon crucible separates into two phases of lead and iron containing carbon. The compositions on the miscibility gap in' the Fe-Pb-C system are 95A%Fe-4.5%C-0.l %Pb and 99.9%Pb-0.1 %Fe. The distribution ratios of copper, tin and zinc between the lead and the iron phases, Lx=[masso/uX in molten Pb]/(masso/uX in molten Fe), are 2.2, 2.2 and lA, respectively. Seventy percent of copper and tin from iron scrap can be eliminated with comparable lead addition. Gold, silver and palladium are enriched in the lead rich phase, on the contrary platinum and rhodium are more distributed to the iron rich phase than to the lead phase.

Jan 1, 2003

By Young-Chul Kang

The Onsan Copper Smelter of LG-Nikko Copper Inc. is a unique plant, which has been operating two smelting processes since 1998. The operation of the first one was started in 1979 with a capacity of 80,000tpy of copper in concentrates utilizing Outokumpu flash- smelting technology. The other one was started in 1998 based on Mitsubishi continuous process with a capacity of 160,000tpy of copper in concentrates. Through several expansion projects, the total smelting capacity of both processes is expected to reach 430,000tpy of copper in concentrates towards the end of 2002. This article describes operation advantages of having two different processes at one plant and comparative operation results in terms of productivity, impurity distribution, energy consumption and environment issues and etc?

Jan 1, 2003

By Y. Kumagai, F. A. Souza

"Electroless plating process has been used in many fields such as automobile and electronic industries. Solutions used in these processes must be disposed or treated. Commonly, in these solutions metal ions, organic materials and others chemicals are in very high concentration. It is very difficult to keep the environmental regulations for disposal of these materials, and the cost of the plating process becomes higher.The objective of this study was to investigate the recovery of components of those baths in order to decrease the cost of the plating process as well as to meet the environmental regulation.In this study the recovery metal ions, sulfate ions, phosphite ions and organic compounds were investigated. Organic compounds used in electroless plating solutions are the organic acids. In this work the solvent extraction of the most used organic acids included citric, lactic, succinic, tartaric and malic was studied. The solvent phase considered in these studies was ethyl acetate.About 95% of the metal ion was recovered by chemical plating onto mica powder. The hypophosphite remained is oxidized to phosphite and with the sulfate ion, both are recovered as calcium salts by selective precipitation in pH 7 and 2 respectively. Organic acids were recovered by solvent extraction using ethyl acetate as solvent phase and the best results were for lactic acid and succinic acid.Along with this study, was developed the analytical parameters to perform wastewater analysis by using Ion Chromatography, High Performance Liquid Chromatography (HPLC), Fourrier Transform Infrared Spectroscopy (FTIR). Ion chromatography was used to perform analysis of sulfate and phosphite ions in liquid matrix, HPLC was used to perform analysis of organic acids in liquid matrix and FTIR was used for characterization of the solids obtained in the recovery processes."

Jan 1, 1997

By Hiromichi Ohta

Precise thermal properties of molten materials are essentially required for analyzing the metal production process. These properties are also important as a clue to consider the dynamic structure of liquid materials. However, it is difficult to obtain the precise thermal diffusivity values of molten oxides at high temperature because of the experimental uncertainties arising from the bubble formation or the severe separation of radiative and conductive heat components. Recently a novel laser flash method has also developed for measuring thermal diffusivity of molten oxides at high temperature. In this new technique, the sample is melted in a metal crucible and heated to the desired temperature. A single laser pulse is flashed on the bottom of the metal crucible and the infrared ray irradiated from the same bottom surface is measured for obtaining the temperature decay, from which the thermal diffusivity of the liquid sample can be estimated. The usefulness and validity of this new laser flash technique have been confirmed by obtaining the thermal diffusivity values of silicate melts in the wide temperature range between 773 and 1673 K.

Jan 1, 2003

By Jin-tao Gao

In order to recover Ti resource from titanium bearing blast furnace slag, a new technology to separate perovskite phase from CaO-TiO2-SiO2-Al2O3-MgO system by supergravity is researched. In the condition of gravity coefficient of 750g, treatment temperature of 1305°C and time of 20min, the significant layers appear in samples which are obtained by means of centrifugal treatment. Along the direction of the supergravity, the volume fraction of perovskite phase increases gradually, and the equivalent diameters of perovskite phase crystals increases with the area approaching to the bottom of the sample. It is indicated that TiO2 is enriched in the bottom of sample as concentrate with a recovery ratio of 74.05% by supergravity treatment.

Jan 1, 2014

By Yongzhong Xiao, Tiejun Chun, Jian Pan, Deqing Zhu

"An innovative process of reverse floatation-direct reduction-low intensity magnetic separation was developed to effectively beneficiate the superfine run-of-mine (ROM) ore mined from Hunan Province, China. Mineralogy was measured that the ROM ore is of superfine low grade hematite ore type, assaying 27.2wt%Fetotal and with main valuable minerals of hematite occurring at size between 3 to 5µm. The upgrading results show that the final iron concentrate, assaying 88.3wt%Fe total and 94.5% metallization degree was obtained at an overall iron recovery of 69.9% under the following conditions: rough concentration by grinding of ROM up to 88.7% passing 0.074 mm and reverse flotation at pH=9.4, 100 g/t starch and 200 g/t dodecylamine (DDA), and coal reducing the rough concentrate pellets containing 12% calcium containing complex additive at 1200 oC for 120 min, and finally magnetic separation of the reduced pellets by grinding up to 89.2% passing 0.043 mm at 0.08 T field intensity.IntroductionWith the rapid development of iron and steel industry in China, there has been a soaring demand for iron ores in the past decade. The imports of iron ores have increased from 148 million ton in 2003 to 628 million ton in 2009 [1]. Iron making industries increasingly demand for high grade raw materials to improve product quality and reduce operation cost. However, availability of high grade natural ores is limited and enrichment of lower grade ores is necessary to meet the demand. Therefore, large quantities of superfine low grade iron resources are necessary to utilize in China at the moment."

Jan 1, 2011

By Hiromichi Ohla

Precise thermal properties of molten materials are essentially required for analyzing the metal production process. These properties are also important as a clue to consider the dynamic structure of liquid materials. However, it is difficult to obtain the precise thermal diffusivity values of molten oxides at high temperature because of the experimental uncertainties arising from the bubble formation or the severe separation of radiative and conductive heat components. Recently a novel laser flash method has also developed for measuring thernnal diffusivity of molten oxides at high temperature. In this new technique, the sample is melted in a metal crucible and heated to the desired temperature. A single laser pulse is flashed on the bottom of the metal crucible and the infrared ray irradiated from the same bottom surface is measured for obtaining the temperature decay, from which the thennal diffusivity of the liquid sample can be estimated. The usefulness and validity of this new laser flash technique have been confirmed by obtaining the thermal diffusivity values of silicate melts in the wide temperature range between 773 and 1673 K.

Jan 1, 2003

By C. M. F. Vieira

The main characteristics and physical and mechanical properties of clays from the county of Campos dos Goytacazes, located at the northern part of the State of Rio de Janeiro, Brazil, are presented. The characterization included mineralogical composition, chemical composition and particle size distribution. The properties related to water absorption, linear shrinkage and flexural rupture strength were obtained in samples that were prepared by 20 MPa uniaxial pressing and fired at 950 and 1100oC. The results showed that the clays are predominantly kaolinitic with high percentage of clay minerals. The kaolinitic structure associated with a small amount of fluxes confers a refractory behavior which makes difficult the sinterization and impairs the ceramic consolidation.

Jan 1, 2009

By Kan Song, Lin Liu, Hengzhi Fu, Jun Zhang, Haijun Su, Xiaojiao Jia

"Al2O3/YAG/ZrO2 eutectic in situ composite has been regarded as new generation of high temperature structural material due to its excellent performance even close to its melting point. The directionally solidified Al2O3/YAG/ZrO2 eutectic ceramics are prepared by recently developed Laser Floating Zone Melting (LFZM) apparatus in which a splitter mirror is used to obtain two beams with the same quality from one CO2 laser. With the two laser beams irradiate the sample from opposite directions, the sample is zone melted. The apparatus configuration and the solidification processing are described in detail. The solid/liquid interface morphology is studied and the mechanism of microstructure formation especially the characteristic of eutectic cellular is discussed. It is shown that YAG and ZrO2 phases play a leading role during the ternary eutectic growth. Meanwhile, the relationship between the solidification microstructure and the processing parameters are investigated.IntroductionAl2O3/YAG/ZrO2 ternary eutectic in situ composite, due to its excellent high temperature mechanical properties, is now considered to be a promising candidate material as a replacement of nickel based super alloy for new generation aero space engine turbine blade [1]. They exhibit flexural strength of 360-500 MPa from room temperature to 2073K in air atmosphere [2]. The compression creep strength at 1873K is 433MPa with the strain rate of 104/s [3]. However, because of the high melting point and complex physical properties, there remain still many difficulties for its application. One of the bottlenecks is the poor understanding of the relationship between microstructure and solidification conditions."

Jan 1, 2012

By Yilin Fang, Alain Bonneville, Timothy. D. Scheibe, Zhijie Xu

"We present a hydro-mechanical model for geological sequestration of carbon dioxide. The model considers the poroelastic effects by taking into account the coupling between the geomechanical response and the fluid flow in greater detail. The simplified hydro-mechanical model includes the geomechanical part that relies on the linear elasticity, while the fluid flow is based on the Darcy's law. Two parts were coupled using the standard linear poroelasticity. Analytical solutions for pressure field were obtained for a typical geological sequestration scenario. The model predicts the temporal and spatial variation of pressure field and effects of permeability and elastic modulus of formation on the fluid pressure distribution.IntroductionIn order to achieve a substantial reduction of CO2 emissions and alleviate the atmospheric carbon problem, massive scale carbon sequestration is required involving millions of tons of carbon dioxide injection over several decades. The geomechanical response is important upon the injection of substantial supercritical carbon dioxide into deep geological formations. Supercritical CO2 is less dense than brine waters and the buoyancy driven flow of CO2 requires the aquifer to be capped by low permeability rock (""caprock"") to prevent the upward migration of C02 (as shown in Fig.1 ). Massive scale injection of C02 changes the overall stress state in the caprock and formation. This change leads to large deformation that can damage the caprock, create fractures, and open new flow paths for supercritical C02. Therefore, a coupled hydromechanical model becomes essential for the caprock integrity analysis."

Jan 1, 2012

By K. Potluri, S. Akella, S. Bhansali

"This paper presents the design and angular strength analysis of microneedles for use as a transdermal interface for drug delivery, fluid analysis and sampling etc. Microneedles of different dimensions were designed and fabricated using various materials viz. Si02, OxideNitride- Oxide (O-N-0). The design, modeling and analysis was done using the Finite Element Analysis (FEA) software ANSYS™ 6.1. Angular strength analysis of the microneedles was done using angular loading in ANSYS™, with the corresponding inaterial property settings. Using the force-displacement settings, forces of magnitudes in the range of 10 mN - 25 mN were applied on the microneedles at loading angles ranging from 30° to 90° was applied on needles. Square and circular shaped microneedles were modeled and the displacements and stresses generated were studied to characterize the angular strength of the microneedles. The buckling and force-displacement analyses show that O-N-O microneedles are more strong and robust as compared to needles of other materials. The analysis shows that while circular microneedles have uniform stress distribution, square microneedles have low stresses concentrated along the edges.INTRODUCTIONIn modem clinical and biomedical applications, drug delivery is done either by oral administration or by hypodermic injection. Hypodermic injection of drugs using needles is often painful. Hence, transdermal drug delivery techniques are increasingly being sought out as an alternative. In transdermal drug delivery the needles puncture the Stratum comeurn - the outermost layer of the human skin. The advantage of transdermal drug delivery (or transdermal measurement) technique, is that it reduces pain and tissue trauma."

Jan 1, 2004

By Ray Y. Lin, Randall A. Blue

"Joining of silicon carbide with infrared using a mixture of Si-30wt.%C as the brazing material has been investigated. Joining was performed at a temperature of 1500 °C in a flowing argon atmosphere for processing times ranging from 5 to 60 seconds. The joining filler materials include thin film silicon obtained by thinning down silicon wafers to about 70 /!m and graphite powder of a 15 /!m average particle size. Joint strengths were determined with a specially designed shear-in-compression jig for testing shear strengths of brittle materials. Cross section examinations of the joined specimens with optical microscopy, scanning electron microscopy and transmission electron microscopy have shown that all joints are essentially void free with excellent wetting between the base SiC and the brazing material. Silicon carbide in the B form has been identified as the reaction product in the joining zone with a transmission electron microscope (TEM) and selected area diffiaction (SAD) analysis. At 1500 °C with a joining time of 60 seconds, the joint has consisted of primarily SiC. With such a high SiC content in the joint, the joint strength is comparable to those by other joining techniques, such as diffusion bonding, as reported in the literature. A kinetic model for the formation of SiC from liquid silicon and carbon is proposed to explain the observed joint microstructural evolution.IntroductionSilicon carbide is of great interest for high temperature structural applications because of its excellent high temperature strength, wear resistance and anticorrosive characteristics [1]. Even though the interest in SiC is high, the use of the material has been limited by the high cost and difficulties involved in forming components of complicated shapes [2]. It is these limitations that necessitate the development of effective joining techniques that are cost effective and able to provide strong joints."

Jan 1, 1996

By N. Panagiotopoulos

A low-grade (1.06% Ni, 0.06% Co) hematitic type lateritic ore from Triada, Euboea Island, Greece, has been leached with sulfuric acid at atmospheric pressure for the extraction of the contained Ni and Co values. The effect of various parameters, including reaction time and leaching temperature, acid strength, pulp density, etc., on Ni, Co extraction and Fe dissolution was determined. By leaching at 95°C for 4h with a 3N sulfuric acid solution at 25% pulp density, Ni and Co extractions were 82 and 75% respectively, and Fe co-dissolution 28%, yielding a pregnant solution containing 2.7 g/l Ni, 0.16 g/l Co, and 33 g/l Fe. Overall acid consumption was 850 kg/t ore (or 100 kg/kg Nil. Preheating of the laterites at 600°C before leaching resulted in much faster leaching kinetics for Ni, but the final extraction and acid consumption remained unaffected; Fe extraction was not influenced. Three-stage counter-current leaching at 9S°C, using 2N acid strength at each stage and 35% pulp density, reduced acid consumption to 350 kg/t ore (41 kg/kg Nil, and yielded 81% Ni recovery. Percolation leaching of -10 mm laterite at ambient temperature with 3N acid for 7 days resulted in 58% Ni extraction.

Jan 1, 1988

By D. de la Villa

From 1989 to 1992 Rio Tinto Minera has developed and implemented a productivity program in its Huelva Plant, including Smelter, Acid Plant and Electrorefinery. This Plan was designed in order to increase productivity, reduce emissions and produce a better quality of cathodes. This paper describes investments and operating improvements involved in this project, focusing on Smelter and Acid Plants, and comments the results obtained so far.

Jan 1, 1993