Search Documents

By Y. K. Rao

In the carbonyl process for the refining of crude nickel CO(g) reacts with nickel in the 310-370K range producing nickel tetracarbonyl, Ni(C0)4(g). Iron and cobalt impurities also form gaseous carbonyls but their partial pressures are low. The carbonyl is led to a decomposer plant wherein the gas disproportionates in the 500-600K range depositing pure metal on nickel pellets that move countercurrent to the gas-flow. This system serves to illustrate the fundamental principles involved in the vapor phase mass transport of elements, against temperature-gradient, under the influence of chemical potential gradient. Unlike in the crystal growth, the source is at a lower temperature (say 350K) whereas the seed is in the hot-zone (say 550K) of the closed ampoule-type reactor. By assuming virtual gas-solid equilibria in the end zones, with diffusion of gaseous species between them acting as a slight perturbation, the quasi-steady- state mass-transport rates are computed for a range of CO-pressures and temperatures.

Jan 1, 1993

By Takaaki Shibata

The Tamano Refinery has developed two new processes for removing the impurities, arsenic, antimony, and bismuth from an electrolyte. The first process involves bleeding the surface electrolyte in the electro-refining cells. The copper concentration level in the outermost layer is lower than that in any of the other layers, while the impurity levels are almost the same in all layers. Bleeding the surface electrolyte increases the amount of impurities removed in the liberator by approximately 20%. The second process involves adsorbing antimony and bismuth from the electrolyte by means of chelating resin. As the electrolyte passes through the packed column of chelating resin, antimony and bismuth are selectively adsorbed. They are then desorbed by means of hydrochloric acid, and then recovered in the form of a highly concentrated antimony chloride solution by means of evaporation. This process almost doubles the capacity for removing antimony from an electrolyte.

Jan 1, 1987

By Nolberto Moreno Borjas

This paper outlines the detrimental impact that unblended ore can have on the Ni and Co recoveries and the ore slurry density with real data from the Caron low-pressure ammonia leaching process for the Punta Gorda ore. The author briefly discusses the reason for the decrease in slurry density that the process experiences. The lower metal recoveries in the process that are caused by the unblended ore chemical characteristics and variations are shown with a data base statistical analysis drawn from the results obtained from a pilot test, designed with different ore bypassed from the normal process flow and a similar ore from a similar metallurgical treatment. Keywords: Ni-Co Laterite, Caron Process, Ore Blending, Slurry Density, Metal Recovery

Jan 1, 2004

Heap leaching with thiosulfate is only used in one location for the treatment of a refractory preg-robbing gold ore initially pre-treated with bio-oxidation. The chemistry of thiosulfate leaching is complex. Further work is required to develop a better control of the system. A mild refractory gold ore containing pyrite and chalcopyrite was used in this study to investigate the use of thiosulfate as an alternative heap leaching technology. Preliminary bottle rolls tests indicated that similar gold extraction was obtained with cyanide and thiosulfate. In the column leach test, effects of thiosulfate, copper and ammonia concentrations, and their ratio on both gold extraction and reagent consumption, were assessed. The range of reagent concentration were: 0.1 - 1.0M (NH4)2S2O3, 0.03 - 0.10M CuSO4*5H2O, 1.0 - 6.0M NH4OH. The solid-liquid ratio was in the range of 0.83:1 to 5: 1. Best results showed that 72% of gold was extracted in 50 days with 0.3M (NH4)2S2O3, 0.05M CuSO4*5H2O and 6M NH4OH or a combination of 1.0M (NH4)2S2O3, 0.03M CuSO4*5H2O and 3M NH4OH. The reagent consumption at solid/liquid ratio of 3:1 was 37 - 48.6 kg/t (NH4)2S2O3 and 0 - 0.62 kg/t CuSO4*5H2O. The results of thiosulfate leaching were also compared with cyanide leaching.

Jan 1, 1999

By Yichi Lu, Haydn N. G. Wadley, Douglas T. Queheillalt

"Using a 3-D ray tracing methodology combined with laser ultrasonically measured elastic constant data near the melting point, ultrasonic propagation in cylindrical single crystal bodies containing either a convex or a concave solid-liquid interface have been simulated and used to design new sensing concepts. Ray paths, wavefronts and time-of-flight (TOF) of rays that travel from a source to an arbitrarily positioned receiver have been calculated. Experimentally measured TOF data have been collected using laser generated/detected ultrasound on model systems with independently known interface shapes. Both numerically simulated data and experimental results have shown that the solidification (interfacial) region can be identified from ultrasonic transmission TOF data. Since convex and concave solid-liquid interfaces result in distinctively different TOF data. When TOF data collected in the diametral plane are used in a nonlinear least squares algorithm, the interface curvature has been successfully reconstructed and ultrasonic velocities of both the solid and liquid obtained. The reconstruction errors were found to be less than 5%.IntroductionMany of today's single crystal semiconductors are grown by variants of a vertical Bridgman technique in which a cylindrical ampoule of a molten semiconductor is translated through a thermal gradient, resulting in directional solidification and the growth of a single crystal, Fig. 1.1 It has long been recognized that during crystal growth the velocity and the shape of the solid-liquid interface, together with the local temperature gradient, control the mechanism of solidification (i.e. planar, cellular or dendritic), the likelihood of secondary grain nucleation/ twin formation (i.e. the loss of single crystallinity), solute (dopant) segregation, dislocation generation, etc. They thus determine the crystals' resulting quality.2-4 The solidification rate and the solid-liquid interface shape are also sensitive functions of the internal temperature gradient (both axial and radial) during solidification.5•6 This in turn is governed by the heat flux distribution incident upon the ampoule, the latent heat release at the interface, and heat transport (by a combination of conduction, buoyancy and surface tension driven convection, and radiation) within the ampoule. The solid-liquid interface's instantaneous position, velocity and shape during crystal growth are therefore difficult to predict and uncontrolled during growth, especially for those semiconductor materials with low thermal conductivity (e.g. CdTe).4-6 The development of technologies to non-invasively sense the interface position and shape throughout the vertical Bridgman crystal growth process has therefore become a key step toward developing a better understanding of the growth process, for enabling sensor-based process control, and thus ultimately for improving the yield and quality of difficult to grow semiconductor materials like CdTe."

Jan 1, 1997

By Stephen K. Pave1

Over 1,100 tons per day of Fluid Catalytic Cracking Unit (FCCU) catalyst is used worldwide. During the cracking reaction, catalyst is contaminated by deposited metals including nickel, vanadium, potassium, copper, iron, sodium, etc. To compensate for contaminants, a portion of the circulating catalyst inventory is withdrawn for disposal and fresh catalyst is added. The DEMETR process takes spent FCCU catalyst and removes a portion of the metal contaminants, enabling the refiner to recycle demetallized catalyst, thus reducing the solid waste from the refinery. Through August, 1993, the operation of one unit for one refiner has resulted in the recycling of over 7,500 tons of spent catalyst.

Jan 1, 1994

By Dr. -Ing. Wolfgang Pietsch

Many primary metallurgical wastes are in the sh.-ape of turnings; borings, chips, dusts, and other particuletes. While such. materials can be easily segregated and/or upgraded to yield high quality ?secondary metals with often known composition for easy recirculation into the production? process; their particulate nature results in various problems. Roller presses are used in an ever increasing number for size enlargement and densification of primary particulate metallurgical wastes for secondary metal recycling. The paper will mention the areas of application from A(luminum) to Z(ink), also including Brass; Cast Iron, lead, and Stainless Steel, as well as dusts from all types of melting and ladle furnaces or converters. Typical systems using roller presses for size enlargement. will be discussed.

Jan 1, 1995

By Bin Du

In recent years, concurrent product design and process is gaining popularity and will become a norm of the industry of the future. Forging has been a critical manufacturing process for production of components with superior tensile strength, toughness and grain flow. This paper describes an expen system which is being developed for forging die design and forging process analysis in concurrent engineering environment. Rules and guidelines pertaining to forgeability are formulated and incorporated into the knowledge-base in building the system. The system is built using an object-oriented paradigm. The object-oriented approach and hierarchical rule structure paradigm are briefly discussed. Finite element analysis packages (ALPID-2D) were incorporated into the program to give the simulation result of the forging process. The system can automatically produce a competent design and recommend a set of processing parameters for a given product. The designer can modify the design according to the result of the simulation.

Jan 1, 1992

By S Ivanaj

Oxidation of chalcopyrite from a copper concentrate in an electrochemical cell having separate-anodic and cathodic compartments was studied by potentiodynamic, potentiostatic and galvanostatic experiments. Oxidation of chalcopyrite particles was mainly realized by in-situ electrogenerated FeIII and Cull ions. The use of an ion exchange membrane, in this experimental set, avoids the reduction of the ferric and cupric ions. The effects of particle size, current feeder potential, current intensity and pulp density were studied to optimize the oxidation parameters. Selective complete oxidation of chalcopyrite was achieved. Oxidation of pyrite was negligible. Mom than 85 % of sulfur was obtained in its elemental form. This may allow selective extraction- of copper from the chalcopyrite concentrate without sulfur dioxide emissions.

Jan 1, 1995

By R. G. Reddy

Reduction of different chromite ores with carbon was studied as a function of C/FeO ratio and temperature in the range 700 °C to 1100 °C by thermogravimetry (TGA) analysis. Powders of chromite ore(-150 mesh) and carbon(-150 mesh) were thoroughly mixed in a desired proportions and were placed in the reaction crucible. The reduction rates of reactions were determined by continuously monitoring the weight loss as a function of time at constant temperature using TGA set up. The analysis of results suggest that FeO present in the chromite ores is reduced to Fe involving gaseous intermediates CO and CO2. The overall rate of FeO reduction is controlled by the oxidation of carbon. A kinetic equation, that of random nucleation, was proposed. The activation energies for the reduction of FeO, present in Roast Movat and Transvaal ores, with carbon were determined to be 55800 and 23000 J/mole, respectively. The results of the present study are compared with the data available in literature. The low activation energy values as determined in this study suggest that the carbon oxidation reaction is catalyzed. It is concluded from the present investigation that the low grade chromite ores can be significantly upgraded to higher value added chromite that can be used as a feed source for economical smelting.

Jan 1, 1998

By José D. T. Capocchi

Viscosity of liquid lead, tin, and Pb-Sn alloys has been measured by the rotational viscometer method in the temperature range from 50 K above their respective liquidus temperature to 823 K. The results are accurate to within ±1.0 %. The variation of viscosity with temperature followed the Arrhenius-type equation µ = µo.exp(Q/RT). The composition dependence of the isothermal viscosity and the activation energy for viscous flow have not shown anomalous changes at the eutectic composition of the Pb-Sn system.

Jan 1, 2000

The Kaldo furnace smelting technique was developed for oxygen steel production by the late Prof. Bo Kalling, Domnarvet, Sweden. Development started in 1948, and production in 1956. Five million tons of steel were produced in TBRC's in 1973. Mainly due to high TBRC maintenance costs, the steel industry now prefers non-rotating converters. In non-ferrous metallurgy, however, qualified new applications of the TBRC technique have been realized or are being considered. Inco, Canada, succeeded to convert nickel matte to metal in the Domnarvet pilot plant in 1959, and have now installed a commercial plant in Copper Cliff. La Metallo-Chimique, Belgium, has pioneered secondary copper smelting and refining in the TBRC, operating plants in Beerse, since 1968, and Alton, U.S.A. Peko-Wallsend Ltd., Tennant Creek, Australia, was faced with the problem of producing saleable blister from concentrates containing 1.5-2.0% Bi. The flash smelting matte, containing 0.2% Bi, could not be refined to an acceptable limit of 0.03% Bi in the blister copper in a Peirce-Smith converter. Tests at Domnarvet indicated that a TBRC would achieve satisfactory bismuth elimina- tion. Two TBRC's were installed in Tennant Creek and operated for 14 months during 1974-75. The problems encountered and how they were over- come are described. Further TBRC applications have been studied in Sweden.

Jan 1, 1976

By José Carlos Abreu

This work presents a kinetics study covering the effects of temperature over the reduction rates of a carbon composite briquette, aiming its use as burden in some of the new alternate ironmaking technologies, such as the Tecnored process. It is reported that increases in the temperature increases the reaction rate. Additionally, the morphology of the iron phase generated during the reduction of these briquettes is presented. It was possible to verify that three types of iron morphology occurred during the process: an external, dense and continuous iron layer, the presence of iron globules at the center of the briquettes and whiskers at the briquette's core. The measurement of the carbon content on the globules and the external iron layer is also presented

Jan 1, 2003

By K. R. Robilliard

The Peru based tin mining company, Minsur S.A., commissioned Ausmelt Limited to design, supervise construction and commission a tin smelter and refinery for production of refined tin metal. The plant is located 240km south of Lima, near Pisco, Peru and is operated by Funsur S.A., the wholly owned subsidiary of Minsur S.A.. Selection of the Ausmelt Technology followed a series of crucible scale test work and pilot plant trials conducted at Ausmelt's facility in Dandenong, Australia and two feasibility studies undertaken by Ausmelt in 1991 and 1993. Ausrnelt began the plant design in 1994 with the construction phase following in 1995. Commissioning of the plant commenced early in 1996 with a target throughput of 30,000 tonnes per annum of concentrates. In mid 1998 oxygen enrichment of the Ausmelt lance air was introduced to expand the capacity to the throughput of 40,000 tonnes per annum of concentrates. The process route involves the use of an Ausmelt furnace for primary concentrate smelting, followed by a conventional tin pyro-refining circuit to produce high grade tin suitable for sale. Further work continues between Ausmelt and Funsur to investigate the use of an alternative, more economical, fuel source and the installation of a second Ausmelt furnace. The paper reviews the project to date with details of ongoing operations and developments at the Minsur Tin Smelter.

Jan 1, 2000

By M. C. Esposito

Seven pyrite samples purified from coal sources and one ore source pyrite (for comparative purposes) have been characterized by chemical and mineralogical analyses, inherent floatability, apparent specific gravity, surface area, semiconductor type, optical anisotropy, dissolution and oxidation rate. The data clearly demonstrate that pyrites from various coal sources differ not only from ore pyrite but from each other as well.

Jan 1, 1987

By F. R. A. Jorgenson

The ignition of chalcopyrite and pyrite was studied using laminar flow furnace and thermal analysis techniques which were supported by XRD and optical microscopic examination of the products. In air, chalcopyrite and pyrite ignited at temperatures of 400-500'C and 500-600?C respectively. The phase assemblages predicted from thermodynamic analyses were compared with those found by experiment, and the onset of ignition was correlated against changes in the phase compositions. Pyrite and chalcopyrite ignited when pyrrhotite and intermediate solid solution formed thus opening up the structure and allowing ready access of oxygen.

Jan 1, 1989

By William Petruk, J. H. Gilles Laflamme, Jean Robitaille, Louis J. Cabri

"A quantitative mineralogical study using ore microscopy, electron microscopy, proton-microprobe, image analysis, and material balances was done on samples from the circuit of a concentrator in Quebec, with particular emphasis on the Cu concentrate. The ore contains many different minerals, of which the principal ones, in decreasing order of abundance, are pyrite, sphalerite, chalcopyrite, bornite, galena, tennantite, and pyrrhotite. Minor to trace amounts of covellite, chalcocite, stannoidite, mawsonite, colusite, wittichenite, miharaite, hessite, petzite, electrum, and an unidentified Cu-Pb-Bi-sulfide also occur.Liberation of pyrite is very high in all size fractions for all samples (ranging from 80-91 %). Liberation of chalcopyrite, bomite, sphalerite, and tennantite is relatively high, on average, in the head .sample and Cu concentrate (55-78% and 66-88%, respectively). Most of the chalcopyrite in the flotation tails is not liberated, whereas about one half of the tennantite and sphalerite are liberated in both the flotation and :final tails. Recoveries calculated for the Cu concentrate (on the basis of assays, mineralogy, and image analysis) are chalcopyrite 72. 5%, bornite 73. 7%, sphalerite 41.0%, tennantite 70.9 %, and galena (together with some trace minerals) 34.2%. It was also calculated that the Cu concentrate contains 10.0 % of the pyrrhotite and i.4 % of the pyrite.Materials balance calculations were done on the five major sulfide minerals to determine the mineralogical distribution of 13 major, minor, and trace elements (as determined by protonmicroprobe analyses). It was determined that tennantite is the principal carrier of Bi (67%), As (90%), and Te (86%) in the Cu concentrate. Therefore, removal oftennantite, which is mostly liberated in the Cu concentrate would significantly reduce these three contaminant elements, but at a loss of9% of the Cu, 2.0% of the Zn, and 0.7% of the Ag. The precious metals (Au, Ag) occur as discrete minerals (electrum, petzite, hessite). Some of the Ag also occurs in solid solution in bornite (23.1% of Ag in Cu concentrate), tennantite, and sphalerite. Four of the major sulfides (chalcopyrite, bomite, sphalerite, tennantite) in the ore also contain measurable concentrations of the following trace elements: Se, Cd, In, Sn, and Sb, occurring mostly as solid solutions. Some of these elements are also concentrated (up to about 18%) in minor and trace minerals such as colusite, stannoidite, and mawsonite."

Jan 1, 1999

By Fumitaka Tsukihashi

Increasing amounts of steel scrap are being used as resources for steelmaking. Therefore, there has been a growing interest in the removal of harmful tramp elements such as antimony, zinc, tin, arsenic, bismuth, lead and copper from the molten steel. The problem that should be solved is the economic removal treatment of residual tramp elements in the steelmaking processes and the production of high quality steel by reducing the effect of the contaminated tramp elements and satisfying the environmental regulations. In this paper, the available thermodynamic data of the residual tramp elements in the molten steel arc summarized and the possibility of the removal of residual tramp elements from the molten steel is thermodynamically estimated.

Jan 1, 2003

By Yasuo Ojima

A new copper continuous converting process was investigated to evaluate the possibility of its application in the commercial operation. The tests were performed both in the laboratory and in pilot plant scale. Bath smelting process with the use of the top submerged lance technology was applied in these tests. Furnace shape was modified to a lengthwise eylindrical one with a settling area. The furnace monitor was put in the settling area to check the furnace from inside, FeOx-Si02, FeOx-CaO and FeOx-CaO-Si02 based slag systems were used to check their efficiency, The optimum slag chemistry to have good metallurgical results was discussed and FeOx-CaO system with some Si02 content turned out to be preferable although it has not been practically used, In this pilot plant test feeding rate of I tIH of solid grain matte was charged consecutively for two weeks and continuous converting could be done successively. This process is expected to overcome the problems of existing processes and be easily applied in existing plants.

Jan 1, 2003

By Yuanbo Zhang, Ruijun Wang, Qian Li, Zhao Jing, Guanghui Li, Zhengwei Yu, Chen Liu

The high content of sodium and potassium in sinter is harmful for blast furnace ironmaking. Reductive sintering technology can remove more alkali metals than conventional sintering process. In order to improve the removal ratios of Na and K, reductive sintering with both CO-containing flue gas circulation and carbon-bearing pellet was conducted in this study. Experimental results show that all indexes except the VSV and P were improved in reductive sintering with CO circulation. Flue gas circulation technique combined with carbon-bearing pellets were beneficial to reductive sintering, because it could maintain good sintering indexes and enhance the removal of Na, K. The best removal ratios of Na, K and reduction degree of iron oxides were 20.37%, 63.73% and 23.76%. In reductive finished sinter, silicate mineral becomes the important binder phase, and main iron mineral phases are wustite (FexO) and magnetite (Fe3O4).

Jan 1, 2016