Search Documents

By Youliang He

Twin-roll casting is an integrated casting and rolling process that involves the continuous solidification of a melt and the plastic deformation of the solidified metal between two rotating rolls. Computer modeling is a valuable tool to help engineers understand the metallurgical process during twin-roll casting. However, commercially available software can only model either the fluid flow/heat transfer of the melt or the plastic deformation of the solid, but not both. In this study, an object-oriented finite element program was developed to simulate the steady-state fluid flow, solidification and plastic deformation of an A7,31 magnesium alloy in a horizontal twin-roll caster. The melt, the mush zone and the solid were treated as a generalized Newtonian flow in an Eulerian reference frame and different constitutive equations were employed to describe the material behaviours. The effect of operational parameters on the solidification process was discussed based on the simulation results.

Jan 1, 2010

By Yongbin Yang

Cathodic reduction of oxygen is a process involved in many fields. As is well known, the mechanism of oxygen reduction usually varies considerably with electrode substrates. In this paper, cathodic reduction of oxygen on gold electrode was studied by linear sweep voltammetry with regards to cyanide leaching of gold. As the results shows, the electron transfer number increases as potential shifted negatively and decreases as pH value increases. Besides, the increment of electron transfer number as a function of potential decreases when pH value increases. When pH increases to 13.0, the volt-ampere curve exhibits a relative flat section with currents approximate to the limit current density of a 2e process. By varying dissolved oxygen concentration, the electron transfer number was calculated for pH11.0 at different potentials, the results being 2.387e, 2.732e, 2.982e, and 3.227e at, -0.35V, -0.40V, -0.45V, and 0.50V, respectively. The calculated current densities are in good conformity with measured results.

Jan 1, 2010

By P. A. Mahanwar

Flyash were melt mixed with nylon 6 at a 30wt% concentration. TYZOR® TPT, a coupling agent, was used to facilitate the link between filler and matrix. The morphological characterization, using SEM, revealed sufficient matrix residue on the filler surfaces thus confirming the strong interfacial bonding between the filler and the matrix on treating. Tensile, impact and the flexural properties of the composites were also improved with the incorporation of coupling agent. As flyash particles tend to impart a grayish color to the plastic, TiO2 pigment was employed to make the formulations aesthetic. The pigment was added to the filled system in 0.1, 0.5, 1.0, 1.5, 2.0 wt/wt ratios. Scattering of incident light and spectral reflectance was higher for smaller particle size flyash. Moreover an increase in the scattering with increase in pigment concentration indicates better dispersion of the pigment, which again is due to the presence of coupling agent.

Jan 1, 2006

By M. I. Brasileiro

The use of experimental design to the study of mixtures has found a wide range of applications, even in laboratory scale or in industrial development works. The aim of this work was to maximize granite sawing waste content in ceramic tiles using experimental design. Based on the raw materials, specific formulations were developed using the experimental design. The raw materials were mixed and sample bodies were produced using uniaxial pressing. The sample bodies were fired and characterized in terms of water absorption, mechanical strength and X-ray diffraction. Regression models were adjusted relating the water absorption and mechanical strength with the amount of raw materials. The results showed that the methodology of experimental design maximize the content of wastes incorporated in ceramic tiles formulations. Formulations containing up to 40% of waste can be used for the production of ceramic tiles.

Jan 1, 2009

By Licheng Zhou

The use of aquatic plants for the removal of heavy metals from wastewater has gained high interest. In this study, batch experiments were conducted to evaluate the adsorption of copper ions in aqueous solution by P. pectinatus L. under various conditions of contact time, initial pH of the solution, metal concentration and adsorbent dosage. The results showed that the maximum adsorption amount of copper ions by P. pectinatus L. was 22.60 mg/g when the initial copper ions concentration was 98.41 mg/L at pH 4.5. The Langmuir and Freundlich models were used to describe the adsorption equilibrium of copper ions on P. pectinatus L. and the adsorption followed the Langmuir isotherm. The adsorption kinetic was well-fitted with pseudo-second-order sorption equations.

Jan 1, 2009

By Jewel A. G. Gomes

Green rust (GR) are layered Fe(II)-Fe(III) double hydroxides, having a pyroaurite-type structure consisting of positively charged hydroxide layers and hydrated ions in interlayers. This special feature of GR is very efficient for wastewater treatment as the pollutants are easily taken in or exchanged with the anions in the interlayers. It can be simply and cost-effectively produced by electrocoagulation (EC). Chicken processing plant (CPP) produces large amount of wastewater containing variety of readily biodegradable organic compounds, fats, and proteins. The possible re-use of properly treated CPP wastewater would be economic and environment friendly. In this study, we present our work on treatment of CPP wastewater using EC, specifically for the removal of COD. Analysis of the EC-treated water for reuse in the same plant is discussed considering the U.S.EPA regulations. Two types of EC-reactors were used for this purpose. To better understand the treatment mechanism, EC-floc was also characterized using XRD and SEM-EDS.

Jan 1, 2010

By M. T. Baquera

A comparison of microstructures associated with W single-crystal ([001], [011], [111]) rods prior to deformation (as grown), and after quasi-static compression (at a strain rate of ~1/s) by transmission electron microscopy (TEM) shows several orders of magnitude difference in dislocation density. Dislocation substructures were not significantly different amongst the deformed sample orientations. In contrast, [001] W rods penetrated into steel targets, at impact velocities of ~1.3 km/s, exhibited heavy dislocation densities and dynamic recrystallization as very distinct microstructural regimes accommodating the penetration process. Twinning on {112} also occurred as a precursor to, or remnant of, these microstructures near the projectile head. These results suggest that deformation accommodating the extreme strains and strain rates associated with the penetration of a single-crystal rod into a metal target is not adequately represented by conventional deformation

Jan 1, 2006

By Chao Li, Shuai Wang, Hongxu Li, Lifeng Zhang, Xie Yang

The method of chloride-hypochlorite leaching has the advantages of short process, low pollution and higher in reaction rate compared with the traditional leaching method. In this research, NaCl - NaClO solution is used to leaching gold from a refractory gold concentrate, and the influence of NaCl and NaClO concentration, reaction time to the leaching rate were investigated in this experiment. The raw materials and the leaching residue were characterized by a series of analysis methods such as XRD, XRF, SEM and EDS. Results indicate that the leaching rate and the desulfurization rate can be achieved at 96.26% and 98% with most optimum conditions as follows: NaCl concentration 50g/L, NaClO concentration 200g/L, Liquid-solid ratio 10:1, the best reaction time was 150 mins. And these conditions should be guaranteed pH<8.0, ORP>900mV.

Jan 1, 2015

By Leo Brewer, Kazuyoshi Shimakage, Mamoru Mitomo, Toshiyuki Nishimura, Yoichiro Uemura, Shinji Hirai

"In the synthesis process of ß -La2S3 via the sulfurization of La2O3 powder using CS2 gas, La2O2S was formed. This occurred at an initial stage of the reaction for sulfurization temperatures below 973K, and ß -La2S3 was also formed at a shorter period for higher sulfurization temperatures. It was found that the oxygen content in ß -La2S3 powders decreased gradually with an increase in sulfurization temperature. On the other hand, the carbon content in these powders increased gradually with an increase in the sulfurization temperature. Though it has been reported that ß -La2S3 was transformed to Y -La2S3 at 1723K± 50K, the sintered compact of double-phase Y -La2S3 and ß. -La2S3 was formed at a rather higher temperature of 1973K when the synthetic powder of ß -La2S3 containing a high amount of oxygen was used. However, phase transformation of -La2S3 to Y -La2S3 progressed preferentially with a decrease in the oxygen content of synthetic ß -La2S3 powder. The Seebeck coefficient of the sintered double-phase Y -La2S3 and -La2S3 was higher than that of the single-phase Y -La2S3, reported previously.Introduction La2S3 exists in three polymorphic forms that are similar to a series of Ce2S3, Pr2S3 and Nd2S3: a, ß , and Y'. The a -La2S3, which is stable at low temperature, is irreversibly transformed to ß -La2S3 of various compositions in the solid-solution range between La2S3 and La3S4, at 923 ± 50K. The -La2S3 may also be an oxysulfide of La10S14O2. Moreover, the ß .-La2S3 phase is transformed to Y -La2S3 ,which has a Th3P4 structure, at 1573 ± 100K. The melting point of Y -La2S3 is 2398 ± 30K where this temperature is similar to those of common refractory materials such as silica and alumina. Therefore, it can be predicted that y -La2S3 which has a high melting point and a thermodynamic stability due to the strong affinity of La for S, would have &high refractory character and chemical inertness in many molten metals. The y -La2S3, colored vivid faint yellow is stable up to 623K in air, where oxidation starts. y -La2S3 is frequently used as pigments for plastics and paints3. Furthermore, Y -La2S3 which is a semiconductor, is considered to be useful as a thermoelectric conversion materials, because it has a high Seebeck coefficient."

Jan 1, 2000

By Taegong Ryu

Nanosized tungsten powder was synthesized by the hydrogen reduction of ammonium paratungstate (APT) in thermal plasma. The effects of operating conditions on the product composition and particle size were investigated. The particle size of synthesized W powder was less than 30 nm in all cases tested. The sintering behavior of the synthesized powder (25 nm average size) was then investigated and compared with those of commercial W powder of 500 nm average size and W powder of 23 nm average size produced by milling the commercial powder. The sintering was done at 1400oC with various holding times. The hardness of the resulting compact from the synthesized W powder (315 VHN) was similar to that from the milled W powder (309 VHN), but the plasma-synthesized powder had a much lower tendency to form cracks. The compacts of both nanopowders were significantly harder than that of the commercial powder (192 VHN).

Jan 1, 2009

By V. Kamavaram

Keywords: Recycling, Aluminum Metal Matrix Composite, Ionic Liquids, BMIC Recycling of aluminum metal matrix composites (MMC) via electrolysis in ionic liquids at near room temperature was investigated. The electrolytic melt comprised of 1-butyl-3-methylimidazolium chloride (BMIC) and anhydrous AlCl3. Impure aluminum composite (Duralcan MMC Al-380, 20 vol % SiC) was electrochemically dissolved at the anode and pure aluminum (>98%) was deposited on a copper cathode. The deposits were characterized by scanning electron microscope, X-ray diffractrometer, and mass spectrometer. The influence of various process parameters such as concentration of electrolyte, and applied cell voltage on the recycling process was studied. The recycling process yielded current densities in the range of 200-500 A/m2, and cathode current efficiency of about 85%. The results indicated that impurities such as Cu, Si, Ni, Fe, Mg, Mn, and SiC particles were removed as anode residue. Energy consumption of about 3.7-6.3 kWh/kg-Al was obtained at a cell voltage of 1.0-2.0 V and cell temperature of 100 ± 5°C. Low energy consumption and no emission of pollutants are the two main advantages of this process compared to present recycling processes.

Jan 1, 2005

By Timo Kankaanpää

Keywords: Solvent extraction, dispersion, phase separation, CFD The liquid-liquid dispersion phases are separated by gravity in a solvent extraction settler. This separation step is made more effective by picket fences. The picket fence geometry and its physical placement have a significant effect on the separation process, because the purpose of a fence is to smoothen and control organic-aqueous dispersion flow in the first part of the settler and achieve a deep and dense dispersion layer in the front end of the settler resulting in a clean phase separation. In this study, physical phenomena in the solvent extraction process and phase separation in a solvent extraction settler with and without picket fences have been examined using a commercial CFX software package. It can be concluded that the used CFD-approach proved to be a complementary tool for optimizing and designing the solvent extraction settler.

Jan 1, 2005

By Ozgul Keles, Dila Sivlin

Lithium ion batteries are potential energy source of next generation electric vehicles (EVs). However, some problems such as safety, durability, low capacity, cycle life etc. restrict their use in EVs. These problems mostly related with cathode materials, an improvement in cathode materials may cause significant changes in battery performance. In this work, to overcome cycle life problem Al2O3 coating on LiNi0.5Mn0.3Co0.2O2 cathode material produced by sol-gel method. The surface modification of LiNi0.5Mn0.3Co0,2O2 was started by adding LiNi0.5Mn0.3Co0.2O2 powders into alumina sol. Then, sonication was started and two different sonication powers were tested (45, 100%). After the second gel is obtained, last heat treatment for Al2O3 crystallization was done at 600 °C for 4 h. X-ray diffraction (XRD) measurements showed that the material had a well-ordered layered structure and Al was not in the LiNi0.5Mn0.3Co0.2O2. Al2O3 coated materials show better cycling performance compared to the pristine material. It is believed that, this improvement is caused by the fact that Al2O3 layer prevents direct contact between active material and electrolyte and reducing decomposition reactions.

Mar 1, 2018

By Sutham Niyomwas

The Fe-TiC composite powder was synthesized in situ by carbothermal reduction of ilmenite. The standard Gibbs energy minimization method was used to calculate the equilibrium composition of the reacting species. The effects of the reaction temperature (1300 °C - 1500°C) and milling time of precursors on the Fe-TiC conversion and powder morphologies were investigated using XRD and SEM method. The synthesized products showed that composite with iron matrix and titanium carbide as a reinforced phase was formed.

Jan 1, 2006

By D. R. Parker

"This paper canvasses emerging trends in public policy and law, which may influence the zinc industry's interest in recycling. There are forces at work beyond direct economic benefits that will drive recycling of zinc, including:• corporate determination to pursue sustainable practices and product stewardship.• public perceptions and pressure,• customer and investor demand,• workforce recruitment, and• protection and expansion of marketsIn this paper, these ""indirect"" forces are examined with particular focus on the zinc industry: It is concluded that, in today's world with an emerging precautionary approach to policy and law making, public perception concerning the environmental implications of metal products, and the need to conserve resources for future generation, a strong industry response is required."

Jan 1, 2000

By Joo Hyun Park, Kyu Yeol Ko

The viscosity of the CaO-SiO2-xMnO-yCaF2 slags (C/S=1.0; x=10, 40%; y=0 to 15%) was measured to clarify the effect of CaF2 on the viscous flow of molten slags at high temperatures. Furthermore, the Raman spectra of the quenched glass samples were quantitatively analyzed to investigate the structural role of CaF2 in a depolymerization of silicate networks. The critical temperature of the slags abruptly increased at 15%CaF2, which was confirmed to originate from a crystallization of cuspidine using XRD analysis. The viscosity of the slags continuously decreased by CaF2 addition in the 10%MnO system, whereas the viscosity of the 40%MnO system was not significantly affected by CaF2 addition. The effect of CaF2 on the viscosity of the slags was quantitatively analyzed using micro-Raman spectra of quenched glass samples accompanying with a concept of silicate polymerization index, Q3/Q2 ratio. A polymerization index continuously decreased with increasing content of CaF2 in the 10%MnO system, whereas it was not affected by CaF2 in the 40%MnO system. Consequently, the bulk thermophysical property of the CaO-SiO2-MnO-CaF2 slags was quantitatively correlated to the structural information.

Jan 1, 2014

By Ovidiu Pasca

The Phelps Dodge Miami Smelter utilizes four Hoboken converters to process molten matte from the Isasmelt vessel. This paper presents past and present improvements in operation, maintenance and process optimization, based on data collection, which has led to increased converter campaign life and copper throughput.

Jan 1, 2005

By Hector Carreon

Due to elevated temperatures, excessive stresses and severed corrosion conditions, turbine engine components are subject to creep processes that limit the components life such as a turbine bucket. The failure mechanism of a turbine bucket is related primarily to creep and corrosion and secondarily to thermal fatigue. As a result, it is desirable to assess the current condition of such turbine component. By using eddy current images, it was shown that the eddy current technique could be used to monitor creep damage in a nickel base super-alloy. The eddy current results also show a significative variation in the electrical conductivity on the creep damage zone with respect to the background zone in nickel-base super-alloy samples. In addition, the absolute thermoelectric power coefficient show also a strong dependence associated with creep damage in nickel base super-alloy samples using a copper hot tip reference. The eddy current and thermoelectric power techniques seems to show promise as nondestructive evaluation tools for monitoring the level of creep damage in metallic alloys.

Jan 1, 2010

By Nobuaki Sato

For the recovery of uranium from spent nuclear fuel, sulfide reprocessing process, which consists of voloxidation, selective sulfurization, and magnetic separation or selective dissolution steps, are proposed. In this paper selective sulfurization of rare-earth oxides in the presence of uranium oxides was studied by thermogravimetry and X-ray diffractometry. In case of the mixture with UO2, the rare earth oxides R2O3 (R=Nd, Eu, etc.) were preferentially sulfurized by CS2 formingoxysulfides and sulfides, while UO2 remained at temperatures lower than 500 °C. When R2O3was mixed with U3O8, first, the reduction of U3O8 to UO2 occurred at low temperatures followed by the sulfurization of R2O3. The separation of rare earth elements from UO2 in suspensionsolution by the use of permanent magnet was examined. The advantage of the proposed process was also discussed by compared with current process.

Jan 1, 2006

By Wojciech Kasprzak, Guoxian Liang, Michel Gauthier, Mickael Dolle, Yulong Liu, Xueliang Sun, Hernando Villazon Amaris, Majid Talebi-Esfandarani, Pierre Sauriol, Thomas Bibienne, Gregory S. Patience, Delin Li, Steeve Rousselot

In the 1990s, LiFePO4 (LFP) was discovered as a cathode material for lithium ion batteries and was successfully used in the variety of devices such as power tools, E-bikes and grid accumulators. New challenges associated with use of lithium ion batteries for automotive applications demand higher performance and operating requirements, yet these requirements need to be achieved at affordable cost and without compromising vehicle safety. The advantages of LFP as a cathode material include thermal stability, limited environmental impact and potential of low cost as compared to the cathode chemistries containing cobalt. Currently, solid state and hydrothermal processes are used to synthesize LFP at the industrial scale. However, they require multiple, time-consuming steps and costly precursors. Recently, a melting-casting process to produce LFP cathode material was investigated. The motivation behind this new process is the great flexibility of raw materials including chemical makeup and particle size, and the use of lower cost, commodity chemicals, with the benefits of increased kinetics in the molten state and energy efficiencies leading to overall process cost savings. Also, if successful this process could represent a novel application of conventional casting. Melting lithium-, iron- and phosphorus-bearing precursors in near stoichiometric ratios and casting LFP material that forms around 1000 °C requires fewer processing steps.

Mar 1, 2018