Search Documents

Researchers from the National Institute for Occupational Safety and Health's Spokane Research Laboratory installed Split-Set rock bolts instrumented with strain gauges to document the mechanical load response of the bolts in weak ground. Short-term monitoring of the bolts immediately after installation showed that some of the gauges went into tension. It was felt that the force exerted on the bolts to drive them into the hole should have caused the gauges to show compression. The tension probably resulted from the holes having crooked sections. Long-term monitoring over the course of a year also showed that the bolts were bending at some locations and that loads as high as 98 kN (22,000 Ib) were recorded along sections of the bolts. Load cells were placed on the head end of the bolts to determine head loads. Head loads up to 14.7 kN (3,300 Ib) were generated during bolt installation. In addition, closure readings were taken across the drift to determine the convergence rate responsible for bolt loading. A Rock Mass Rating (RMR) was calculated at the site to compare with bolt response. The bolts were installed as part of the rebolting process in an area being repaired because the near-vertical beds in the walls were buckling and causing the wall to fail. The instrumented Split-Set rock bolts will provide data that will lead to greater understanding of the behavior of the rocklbolt support mechanism. It may also be possible to explain the overall performance of the bolts in situ in terms of their design effectiveness. This work showed that load at the head of a Split-Set rock bolt was less than load along the interior of the bolt.

Jan 1, 2005

By James J. Scott

Over the past two years research, development ad field tests have been conducted on a new product called the "Scott Cable Sling". This work resulted in the awarding of U.S. Patent No. 4265571 on May 5, 1981, to the inventor. Work on this' project was done by the staff of Scott Mine Technical Services, Inc., and is in keeping with its philosophy of advancing mine grad control technology. Recent acceptance by industry has resulted in volume purchases of the product and indications are that it will gain wide acceptance by the mining industry. The system features flexibility in its application and is useful in both roof and rib control. This paper describes the product, discusses its range of applications and cites specific field examples of its use.

Jan 1, 1981

By Mietek Rataj

Installation of pre-tensioned Strand Bolts i.e. resin grouted cable bolts is very common now in Australian coal mines. A short historical development of this type of rock reinforcement is outlined Various systems have been developed to apply 20 to 25 tonnes of pre-load to these bolts but there are still some technical problems which have to be overcome. One of the major problems encountered is bleed off tension which is highly undesirable as required "over loading" rocks the immediate roof thus inducing fractures iii weak strata. The major reason for the loss of tension apart from the design of the tensioning jack, is the design of the conventionally used barrels and wedges. Due to a roof plate tilting during tensioning the cable moves out of the barrel centre which impedes proper positioning of the wedges and subsequent excessive return of the cable once load of the jack is released. This problem has been largely resolved by the design of a special barrel having a centralizing rim allowing for significant reduction of the toss of tension. KEYWORDS: Pre-tensioned Strand Bolts, Cable Bolts, Bleed off Tension, Tensioning Jack, Loss of Tension

Jan 1, 2002

By M. V. Kurlenya

The experience of application of geomechanical investigations for substantiation of extraction of undermined ore deposit in the north of Siberia is discussed. The finite element method was used for forecasting the state of massif during the development of mining works. The results of calculations were compared with the experimental data of observations in situ for evaluation of authenticity of numerical modelling.

Jan 1, 1990

By George Gardner

The rapid growth of highwall mining in the Appalachian coalfields has resulted in unique safety concerns. Due to the concentration of activity at the base of the highwall and the potentially destabilizing influence of the mining process, proper mine planning and continual monitoring of the ground conditions is essential to ensure a safe and productive operation. This will also help to minimize the need to recover equipment that has become entrapped underground, and the subsequent hazards associated with a recovery operation. Adequate geotechnical site investigation and rational design methods should enable mine planners to properly account for the site-specific conditions that influence web and abutment pillar, roof, floor, and highwall stability. This paper examines the growth of highwall mining, provides a general overview of the various safety concerns, and reviews the modes of highwall failure as they relate to a highwall mining operation. Gcotechnical considerations that should be taken into account before and throughout the mining operation are emphasized. The importance of closely examining and monitoring highwall conditions for subtle signs of highwall instability will be discussed.

Jan 1, 2002

By Tom Denton

The bolt design criteria, since it was first published by Dr. John Stankus (Stankus, 1997), has been recognized as an important tool in ground control design. This concept is based on the Optimum Beam Building Effect (OBE), which is defined as the roof beam that has no separation above or within the bolted range and having the shortest bolt possible. This paper will present an application of this concept at the American Coal Company. Galatia mine. This mine previously used a 6' and 7' length bolt. However, since seam thickness has gotten smaller in the Southern area of the nine, a two-piece bolt is required. A two-piece bolt increases ground control costs and delays production. Therefore, a one-piece, shorter bolt, if feasible, can reduce costs and expedite development. In this analysis, Computer modeling is first conducted to determine bolt length and installed load. Second, a special bolt is developed, that can achieve the proper installed load as determined by the computer modeling. Third, underground bolt pull and load cell tests were conducted to evaluate bolt performance. Finally, an underground "bench" test was conducted. The test results have shown that entry convergence in the short bolt (5) test area is less than the 6' bolt area. Overall roof condition in the test area was as good as the 6' bolt area. Based on this analysis, the mine has converted to a shorter bolt in the low seam area and it is working well.

Jan 1, 2000

By Dieter Wittenberg

The use of thc ultrasound technique for monitoring rockbolt support has at last provided support engineers with a measunng system capable of pinpointing fracture failuns in fully-grouted rockbolts. The measurement data are based on the operatmg characteristics of the bolt type, which are determined both under test-bench conditions (DIN 21521) as well as in underground trials. Practical experience acquired to date suggests that this new measuring system is both effective and reliable.

Jan 1, 2001

By A. Mahyera

BETTER ROOF SUPPORT During the last decade, resin-grouted roof bolts have taken a substantial foothold in the coal mining industry - now accounting for about one-third of all bolts installed annually, due to the improved roof support. However, the high cost, toxicity and flammability of the resin cartridges appear to be a limiting factor in even greater use of such bolts. Terra Tek, Inc. has, over the past few years, been developing a novel roof bolting system to mix/inject a very fast-setting and high strength inorganic cement into bolt holes and install point-anchored or full-column grouted rebars - all automatically and at substantial cost savings. This grouting system utilizes a unique method to mix the grout ?in-the-hole?. It has been integrated with a conventional bolter, retrofitted with an indexing-head mechanism and an on-board pneumatic computer to sequence and Control the drilling, grouting and bolting. Cycle times are the same or better than for a resin system. Following laboratory testing/development, the prototype system has undergone field trials in a Utah coal mine. A description of the bolting system, results of pull-tests in the laboratory and field, and economics and productivity gains with this system in comparison to a conventional resin-cartridge bolting method are presented. The relationship of this technique to improved roof control is also discussed.

Jan 1, 1984

By Wei Wu

A new bench blast design method and its realization with the assistance of the computer is introduced. The basic design principle is to define a rhomb cell, called fully-fractured zone, through a series of full scale bench crater tests and apply this geometric pattern in multi-hole, multi-row blast design. To illustrate the design method, the optimization process and assessment of blast performance are presented in the context of a case study.

Jan 1, 1992

By Chris Mark

The Coal Mine Root Rating (CMRR) was first presented at this Conference nine years ago. Since Its Introduction, the CMRR has been incorporated into many aspects of mine planning. including longwall pillar design, rout support selection, feasibility studies. and extended cut evaluation. It has also become truly international, with involvement in mine designs and funded research projects iii South Africa. Canada. and Australia. The purpose of this paper is to bring the minim community Up to date with recent improvements and applications of the CMRR. The must important new development is a streamlined process for determining the CMRR from exploratory drill core. Just three types of information are Jaw required: Fracture spacing (or RQD) Uniaxial compressive strength for axial Point Load Testing) Diametral Point Load Testing The moisture sensitivity adjustment has also been changed, and new research has related the immersion test to slake durability. Most recently, the CMRR has been implemented in a computer program. which can be obtained from NIOSH free of charge. The program facilitates calculation of the CMRR firm either underground or drill core data. Values from ninny locations can he saved in a single file. and an interface with Autocad allows CMRR contour plots to he integrated 11110 mine planning.

Jan 1, 2002

By Thomas W. McClain

This paper describes the importance of considering ground control measures when importing U.S. continuous mining technology in foreign countries. Important ground control factors are discussed. Each year the USA exports a significant amount of continuous miner equipment (i.e. continuous miners, roof bolters, coal haulers, shuttle cars, continuous haulages, scoops and feeder-breakers). International customers see the opportunity to significantly improve their productivity and increase their longwall gateroad development rates by implementing the room-and-pillar (place changing) mining systems used throughout the USA. However, a number of issues are often overlooked or not thoroughly evaluated when selecting the equipment, often resulting in lower than expected productivity. Ground control is one of the critical factors that must be addressed. Since 1993, the author has assisted numerous international customers and manufacturers with implementing or improving the performance of continuous miner and room-and-pillar systems in Australia, India, Mexico, South Africa, and the United Kingdom. An essential first step is to conduct a thorough ground control study, and then integrate its findings into mine layout, equipment selection and section operating plans. Based on actual case histories, the author will present a number of examples and "Do's and Don'ts." Another key to success is the involvement of manufacturers and suppliers with customers when implementing new systems and technology. The importance of allowing for cultural evolution by both management and workers for acceptance and successful implementation of any new system is also discussed. Over the past ten years, the global coal industry has gone through some very dramatic changes. Countries that previously experienced a freight advantage, such as Australia shipping coal to Japan and Korea versus the United States, are finding they are now in a world coal market similar to other commodities and products. Today, coal prices arc stated F.O.B. at the consumer, and the origin is often irrelevant. Also, previously state-run coal industries have been privatized, such as the United Kingdom, and others such as Poland and India are currently going through the same transition from state-run to the private sector. In all cases, the key to continued viability, or survival, depends largely on reducing costs in order to compete for a market share. Two ways exist to reduce costs. First, almost everyone tries to reduce expenditures. Depending on the circumstances at a given mine or in a specific country, this helps to some point. However, most find that secondly, production must be increased to achieve the necessary cost reductions to compete in today's global coal market. As a result, over the past ten years, foreign companies and countries have looked to the USA for new mining methods and systems to significantly increase productivity. Thus, a major portion of American equipment manufacturers and suppliers sales have been exports, which has played a major role in helping to "keep-the-doors-open" for a number of companies through the lean 1990's, when American coal companies were postponing capital expenditures and expansions. As foreign companies and countries have looked to the USA for ways to improve productivity, they have become particularly interested in continuous miner equipment systems and most often "room-and-pillar," "bord-and-pillar" or "place changing" mining systems for four reasons. First, in countries such as the United Kingdom and Germany, who have been longwall mining for generations, there remain numerous remnant small pockets of reserves in existing mines that are either too small or too difficult to longwall mine, and are conducive to the flexibility of continuous miner systems. Second, for countries such as Australia, who have experienced the constant problem of developing longwall gateroads in a timely manner to avoid longwall move delays, new or alternate methods are required. Third, companies and countries using roadheader machines on coal production are recognizing the increased productivity potential of continuous miner equipment. Fourth, countries such as South Africa and India, where a substantial amount of the production comes from conventional mining methods, "drill-and-blast", companies are recognizing the opportunity to improve by implementing continuous miner technology. Colliers & Associates, Inc. has found that over the past eight years too often foreign companies or countries purchase American continuous miner equipment without first conducting a thorough geologic, geotechnical and ground control study for the reserves to be mined. The problems are compounded by not developing mine plans, and submitting them to the regulatory authorities for approval prior to purchasing and even implementing the equipment.

Jan 1, 2001

By Thomas Barczak

Longwall mines typically use some form of standing support for secondary roof support in longwall tailgate entries. Although there have been several new support products developed for this application, there remains no universal design criteria to optimize the application of these support technologies. The requirement for optimization and proper support selection is to understand the degree of control that the support has on the ground behavior. The ground reaction curve and numerical modeling was used to evaluate the impact of standing support on ground behavior. LaModel was used to evaluate the impact of standing support on main roof and floor behavior and pillar yielding. The conclusion drawn from this study was that standing supports do not have sufficient capacity to control main roof or floor loading or prevent the resulting convergence of the tailgate entry. However, it is imperative that this "uncontrollable convergence" be considered in the support design to prevent premature failure of the support. A FLAC model was used to evaluate the near-seam roof and floor behavior in conjunction with the global vertical and horizontal stresses. The model suggests that standing roof supports can have some impact on the ground behavior as the elastic response of the rock is exceeded and rock structure deteriorates from the stress concentrations that develop around the tailgate opening. During this phase, the capacity and stiffhess of the standing support can be critical to the stability of the opening, as eventually the rock mass will be transformed into a partially detached structure whose weight must be supported by the standing support. This work is part of a ground control program of research at the National Institute for Occupational Safety and Health (NIOSH) aimed at improving mine safety by reducing roof fall injuries and fatalities.

Jan 1, 2005

By William R. Kohl, Craig B. Clemmens

"Since 2010, North Central Resources, Bridgeport, WV, has been using the sonic log to estimate the rockmechanics properties of the coal and adjacent strata in their exploration drilling program. In 68 out of the 85 boreholes they have drilled since 2010, they have conducted shear wave analysis on sonic logs run in these boreholes. By incorporating the rock mechanics logs into the geological model of the coal seam, the engineers can develop a better understanding of the support requirements for the mine.WellCAD Borehole processing software provides vastly improved efficiency in analyzing shear waves from borehole sonic data than previously available methods. The calculation of most rock mechanics parameters requires knowledge of the density and both the compressional wave velocity and the shear wave velocity. Density logs are well known and an industry standard. Sonic logging is equally well known, although less frequently used, as an accurate source of compressional wave velocity. Shear wave velocity is difficult to measure in a geophysical log, but can be estimated from digitally recorded wave form records. This is a time consuming manual procedure which requires the visual examination of thousands of individual wave forms.WellCAD allows the viewing all the wave forms on a VDL display. The observer can create a pair of false logs by manually tracing the interference points on the display for each receiver. He can check himself by observing wave forms in the traditional format. He can then create a shear wave transit time log or “Delta-S” log by subtracting the false log from the near receiver from that of the far receiver. This can be plugged into standard formulae to generate curves for most standard rock mechanic parameters, including bulk modulus, shear modulus, Young’s modulus, and Poisson’s ratio.While these parameters do not entirely substitute for destructive testing, they are extremely cost effective. An entire borehole can be analyzed for the cost of a single destructive test. This allows for a more judicious use of destructive testing while permitting the extension of test data into the rock mass with much greater confidence."

Jan 1, 2015

By Yoginder Paul Chugh, Jason E. Tinsley

"Over the last five years, the authors have compiled a database of Short Encapsulation Pull Test (SEPT) evaluations from Interior Basin (Basin) coal mines. Typically, SEPT data are analyzed to obtain peak load carrying capacity per unit length of resin encapsulation designated as the ""Grip Factor,"" or GF. In a previous paper, ""An Analysis of Short Encapsulation Bolt Pull Test (SEPT) Data From Interior Basin Coal Mines,"" authors analyzed tangent value of the load-displacement curve as Anchorage Stiffness at 50% (AS-50) of the peak load, or GF value, to assess reinforcement potential of an installed bolt system. This paper attempts to correlate the secant AS VALUES (of SEPT on 6 ft (1.8 m) long installed bolts at a lower load of about four tons from several different mines in the Basin with their MSHA-approved primary support requirements. Since the current regulatory environment requires plan changes dynamically to ensure that roof falls are minimized, the authors hypothesize that the practiced roof control plan must meet the minimum requirement of adequately supporting immediate roof strata. The analyses are based on 181 SEPT studies performed by Minova professionals. Analyses indicate a macrolevel correlation for both roof support density and roof support cost that may have the potential to be used by mine operators to compare their performance with other mines in the area. Limitations of the analyses include ignoring mining depth, mining height and required secondary supports as part of the requirements for a roof control plan. The authors recommend additional analyses to develop this concept further to develop guidelines that can be confidently used by coal companies.INTRODUCTIONPartially- and fully-grouted bolts are extensively used in coal mines for roof support as part of MSHA-approved roof control plans. Since grouted bolts have a larger area of contact with the rock, they can develop much greater anchorage capacity than conventional expansion shell (point-anchored) bolts. Load transfer characteristics and interaction mechanics between steel rebar, grout and rock mass around the bolt hole for grouted bolts are generally assessed in the laboratory or field though short-encapsulation pull tests (SEPT), which have been extensively researched by Aziz and Jalalifar (2005), Aziz (2004a), Serbousek and Signer (1987), Signer (1990), and Mark et al. (2002), among others. In a SEPT, about 12 in. (30 cm) of bolt length is typically encapsulated in resin and a pull test is performed to collect load-displacement data prior to failure and, in some cases, post-failure. A typical load-displacement data set for a bolt is shown in Figure 1. SEPT characteristics are designated by peak load carrying capacity, or grip factor, which is the peak load carrying capacity per unit length of resin encapsulation. SEPT is routinely used to assess anchorage performance characteristics of different lithologies overlying a coal seam to identify type of bolt, bolt diameter, length and spacing across and along an excavation. Anchorage stiffness, or AS, at any load may also be calculated as the tangent or secant value of the slope of the load displacement curve at a particular load level. Anchorage Stiffness characteristics of bolts from SEPT data have typically not been considered in any depth until recently (Chugh et al., 2014; Chugh et al., 2015)."

Jan 1, 2016

By Yanfa Gao

Clusters of underground openings were developed around the shaft bottom of Tangshan Mine. They were deep and located in soft rock strata. After development, those openings have been subjected to considerable deformation and damages. A combined supporting method including grouting and bolting, shotcrete lining and brickwork was used. This paper analyzing the theories on which this supporting method was based. A new theory called "Disturbed Creep" was developed for deformation prediction of openings surrounded by strata subjected to stresses close to limiting or failure strength. Keywords ground pressure, deep mine, soft rock, stability control

Jan 1, 2002

By Craig Compton

The The National Institute for Occupational Safety ane Health (NIOSH) Pittsburgh Research Laboratory (PRL) is continuing to investigate the behavior of fully grouted roof bolts in the weak roof rock of the Safety Research Coal Mine (SRCM). This paper describes the results of three studies: A series of 24 pull tests of bolts installed fully grouted and overcored to leave 12 inches of grouted bolt. The tests compared the pull-out performance of offset-head roof bolts with that of standard 518-inch bolts; A second series of 24 tests that compared the pull-out loads obtained by bolts installed with 1 R of resin (a Short Encapsulation Pull Test or SEPT) to that of fully grouted bolts overcored to leave only 12 inches of grouted bolt, and An investigation into the pressures generated during the installation of fully grouted resin bolts. All of the bolts installed and pulled were overcored and removed from the roof after the pull tests to allow inspection of the resin. The first study found that there was no significant difference in pullout load between the offset-head bolts and the standard bolts. The second study, comparing the SEPT bolts and the partially- overcored fully grouted bolts, indicated that SEPT can significantly underestimate bolt anchorage grip factor, suggesting that the SEPT is a conservative measure of actual bolt performance. Significant loss of resin to cracks in the roof was observed in the bolts overcored in the SRCM. The third study explored one possible explanation for the resin loss, high pressures generated during bolt installation. These tests employed bolts installed in strain gauged steel tubes. The results confirmed that significant pressures (greater than 4,000 psi) can be generated during bolt installation. The results of the pressure tests, combined with the observations of resin loss in bolts installed in the SRCM, suggest that under some circumstances resin loss and under-encapsulation could take place and lead to degraded bolt performance. Glove fingering was observed in all recovered bolts to various degrees. The limited comparative data suggested that the effect of glove fingering ranged from slight to moderate. Complete mixing of the resin was observed on all of the 40 bolts recovered (28 fully grouted and 12 SEPT). Australian and U.S. resins were compared and the Australian resins were observed to have much smaller catalyst compartment areas and lower resin viscosities. These differences are suggested as potential explanations for occasional resin mixing problems noted in Australian resin bolt installations.

Jan 1, 2005

By Bruce K. Hebblewhite

This paper provides an overview of the international ?state of the art? with respect to underground coal mining methods used in seams of thickness greater than 4.5 m, through a review of a selection of high performing thick seam mining operations around the world?both Single Pass Longwall (SPL) and Longwall Top Coal Caving (LTCC). The paper discusses the recent operational experiences from these selected faces, together with the ground control issues faced, and identifies some of the major, inherent geotechnical factors that can influence the mining method selection, design criteria, and ultimate performance, from both an operational and safety perspective. It is clear that both of these methods are developing quickly? not only from an operational and equipment perspective, but also from the understanding of critical geotechnical criteria. There is an increasing role for both methods in thick seam environments, although the higher SPL faces will only be successful in the near to mid-term under benign geotechnical environments. Regardless of the method, a thorough understanding of the critical geotechnical factors is a key to successful implementation of either method.

Jan 1, 2013

By Arthur Miller, Andrew Weakley, Heather E. Lawson

"IntroductionDynamic failure events in an underground coal mine, or “bumps,” are defined as “the sudden, violent bursts of coal from a pillar or pillars or a block of coal, resulting in a section, the whole pillars, or the solid block of coal being thrown into an open entry” (Peng, 2008). Reports of disastrous and often fatal dynamic failure events date back over one hundred years in the United States. Mining practices and technologies have significantly evolved over the course of the last century, yet these events continue to occur. The events at Crandall Canyon, Utah (Gates et al., 2007) and Brody No. 1 Mine in West Virginia (Barker and McNeely, 2014) are two recent failure events that resulted in a total of eleven fatalities. These events testify to the fact that dynamic failure remains an imperative safety concern. Furthermore, their continued occurrences indicate that engineering controls have proven inadequate at wholly mitigating the problem.Multiple conditions have been associated with the occurrence of dynamic failure phenomena, including• thick, competent strata that can create a bridging effect, resulting in high abutment stresses (Rice, 1935; Holland and Thomas, 1954; Iannacchione and Zelanko, 1995; Agapito and Goodrich, 2000; Peng, 2008; Whyatt, 2008; Whyatt and Varley, 2010)• overburden thicknesses greater than 500–700 ft. (Rice, 1935; Peng, 2008)• a strong coal that is resistant to crushing (Rice, 1935; Peng,2008) or that is “uncleated or poorly cleated, strong…sustains high stress and tends to fail suddenly” (Agapito and Goodrich, 2000)• the presence of sandstone channels or rolls that can serve to concentrate stresses (Iannachione and Zelanko, 1995; Agapito and Goodrich, 2000)• fracturing of strong units above or below the coal seam (Whyatt and Varley, 2010)• slip along pre-existing discontinuities (Peperakis, 1958; Whyatt and Varley, 2010)• multiple seam mining interactions (Campoli, Kertis, and Goode, 1987; Iannachione and Zelanko, 1995; Newman, 2002; Peng, 2008)• mining sequences that can cause anomalously high stress concentrations (Campoli, Kertis, and Goode, 1987; Iannachione and Zelanko, 1995)"

Jan 1, 2015

By Yvette Heritage

"The risk of fatalities from rib failure is still prevalent in the coal mining industry. This risk has prompted further research to be conducted on rib deformation in order to understand the mechanisms of rib failure, with the long-term objective being to improve rib support design. This paper presents the results of ACARP research project C25057, which investigated the mechanics and drivers of rib failure. The results of rib deformation monitoring at three different mines in Australia provides rib deformation characteristics for overburden depths ranging from 160 m to 530 m. Monitoring includes deformation during development drivage conditions and during the longwall retreat abutment stress environment. The rib deformation monitoring covered three different seams: the Goonyella Middle Seam, Ulan Seam, and Bulli Seam in the Bowen Basin, Western Coalfield, and Southern Coalfield, respectively. The observed mechanisms driving the rib deformation ranged from bedding shear failure along weak claystone bands to vertical shear fractures to kinematic failures driven by shear failure dilation. The variation in mechanisms of rib failure, together with the seemingly consistent method of rib support design, prompts the question: What exactly is the role of rib support?INTRODUCTIONThe current risk of rib fatalities in the coal mining industry has prompted further research into understanding the mechanisms of rib failure. Three Australian mines assisted further research by providing sites for rib deformation studies as part of the Australian Coal Association Research Program (ACARP) project C25057. The mines included in this study were Moranbah North Mine, Ulan West Mine, and Appin Mine. This paper provides key results of the rib deformation monitoring relevant to assessing the mechanisms of rib deformation.The approach of monitoring rib deformation and rib support loads was used to measure and characterise the dynamic rib deformation present in both development and longwall retreat stress environments. The characterisation of rib deformation, together with rock failure modelling, was used to determine the mechanisms for failure within the rib and to assess the interaction of rib support with the failure process. The mechanisms of rock failure are considered an important factor in understanding the drivers for the failure. Consideration of the site-specific failure mechanisms can provide for a more tailored support design."

Jan 1, 2018

By Gary Buchan

"Mine-wide ground control stability is essential to any mining operation to prevent catastrophic failure of underground structures. The ability to recognize or indicate the potential for ground control hazards in underground mine operations is highly desirable to reduce or eliminate ground-control-related injuries and fatalities. The acoustic emissions (AE) form of non-destructive testing has been used for decades to determine material or machine deterioration or potential failure. This paper presents the findings of research in AE with the results of laboratory bolt pull tests and comparisons to field experimentation, including AE sensors and bolt load data in an underground stone mine. The goal of the project is to compare laboratory results of AE sensors on roof bolt pull tests with field experimentation to determine the capability of predicting bolt failure or roof deterioration.INTRODUCTIONMine-wide ground control stability is essential to any mining operation to prevent catastrophic failure of underground structures. The ability to recognize or indicate the potential for ground control hazards in underground mining operations is highly desirable to reduce or eliminate ground-control-related injuries and fatalities. Typical ground control monitoring devices involve drilling into roof or rib, grouting or gluing of sensors, and dedicated cabling for data collection. One of the original goals of this research was to develop a methodology for a simple wireless device that could provide an indication or warning of potential roof bolt or roof failure. Various types of nondestructive testing (NDT) have been used for decades to determine material or machine deterioration or the potential failure of either. One type of NDT is acoustic emission (AE) monitoring, which has been studied for use in mining to predict rock bursts and mine failures since the 1940s (Obert, 1941; Obert and Duvall, 1942). The primary goal of the work was to compare laboratory results of AE sensors on roof bolt pull tests with field experimentation to determine the capability of evaluating bolt loading or roof deterioration in an underground stone mine. Bolt pull tests were conducted in the laboratory to establish a repeatable trend of AE activity versus bolt load. The second part of the project was to then install bolt load cells in an underground stone mine and monitor AE activity in the vicinity of mining."

Jan 1, 2018