Search Documents

By A. H. PH. D Wilson

Compared to the rocks encountered in, say, metalliferous mining or tunnel drivage in igneous and metamorphic rocks, the strata associated with the coal measures are relatively soft. If excavations are made at depths greater than one or two hundred metres, zones of fractured or yielded rock develop around the openings. The stress which can be taken by yielded rock at the boundary of an opening is low, but because of the friction present between the fragments or particles, the sustainable stress rises rapidly with distance from the opening until sufficient confinement has been developed to prevent failure of the rock in the first place. Thereafter the laws of elasticity will apply and increasing distance will reduce the stress field until conditions consistent with the cover load are reached. For rocks which maintain their elastic condition right to the edge of an opening, finite element analysis and similar techniques have proved successful in determining the distribution of stress around the opening. This approach, however, is not successful when a yield zone is introduced between the elastic zone and the opening. Nevertheless, some estimate is required if help is to be given in the siting of roadways and in the determination of adequate pillar sizes. This matter is of particular importance in the planning of new mines especially if retreat faces are involved, as extensive roadway drivage must be planned and executed before experience of the effects of face extraction is gained. In 1977, the author published [I] a method based on 'stress balance'. The total aggregate downward load over a large area will remain that of the cover load even after part of the coal seam has been removed. Any rise in stress in ribsides and pillars must be offset by an equivalent stress reduction across roadways and other areas of extraction, and vice versa. Knowledge of one can lead to an estimate of the other, provided the general form of the stress distribution can be postulated. It is the object of this paper to revue the method in more detail and to give further examples of its successful application.

Jan 1, 1981

By S. Jayanthu

This paper presents analysis of strata behaviour with special reference to convergence and stress variation during an experimental trial of extraction of pillars with cable bolts as major support system in 6.5 - 8.0 m thick coal seam. Critical span for roof falls was estimated through empirical models and also evaluated by numerical models. In situ strata behaviour studies during 1992-96 for about 70 local/major falls revealed inadequacy of the available literature for interpretation and prediction of the roof falls. Convergence acceleration and variation of induced stress based on continuous monitoring data showed distinct anomalies and potential for better understanding of strata mechanics during pillar extraction.

Jan 1, 1998

By Pieter-Jan Kleiterp

Caterpillar has been involved in highwall mining since the purchase of Bucyrus in 2011. The Cat® HW300 is a continuation of the Superior Highwall Miner that was first sold in the USA in 1994. Currently, there are more than 80 machines supplied worldwide, and Caterpillar envisions increasing the population steadily in the coming years. The Cat highwall miner product group, based in Beckley, WV, has been involved in the sales of all miners to date. With the dealer model that Caterpillar is using, more people, dealers in particular, need to be trained on the application of highwall mining. A site investigation is a highwall specialist?s work, and Caterpillar assists dealers and customers in determining the technical feasibility of highwall mining on mine sites. With the ever-increasing amount of requests, it proved to be important that people without highwall mining expertise, yet who are familiar with mining, could perform a very quick analysis of a potential highwall mining site to determine at an early stage if it is worthwhile to invest the time and money of all parties?customer, dealer, and Caterpillar?in further follow-up. Therefore, Caterpillar would like to introduce the Cat HW300 QuickScan tool.

Jan 1, 2014

The applicability of four empirical strength criteria for rock masses, namely, Hoek and Brown, Bieniawski - Yudhbir et al., Rarnamurthy - Arora and Johnston - Sheorey et al. has been tested against the triaxial test data for jointed plaster of Paris of Arora. The following modified Bieniawski criterion shows best agreement with the triaxial test data for jointed plaster of Paris:- where st = axial compressive stress at failure, MPa; s3 = confining pressure, MPa; scm = uniaxial compressive strength of jointed plaster of Paris, MPa; and B = - 3.988 + 9.674 (scm )-0? 185 The modified Bieniawski strength criterion can be used to estimate the strength of a coal pillar, based on a knowledge of stress distribution in it.

Jan 1, 1992

By Benjamin Mirabile

"Current and emerging practices to ventilate longwall gobs are prompting increased design and analysis of standing support requirements related to longwall mining. Specifically, additional design methodologies are being employed to evaluate standing supports in the #2 entry of a 3-entry longwall system.Numerical modeling will be used to evaluate the performance of standing support in the #2 entry between gobs of longwalls in the Herrin No. 6 seam. The performance of standing support in the #2 entry will be evaluated based on the following: (1) The effectiveness of standing support in maintaining an open airway in the #2 entry; (2) The interaction of standing support in the #2 entry with standing support in the longwall tailgate; and (3) Loading conditions of longwall pillars. Initial numerical modeling activities are focused on evaluating the roof to floor convergence in the #2 Entry and using the ground reaction curve concept for support design.Numerical modeling indicates that, like standing support in tailgates, supports in the #2 entry require some type of yield mechanism to withstand initial uncontrolled convergence. Numerical modeling also suggests that support density can be lower than that used in a tailgate support application. The numerical models used for initial investigation of support performance in the #2 entry are limited in their ability to evaluate support performance. The magnitude of uncontrollable convergence can be estimated with LaModel software. Near-seam conditions have not been investigated in this research since the LaModel software does not have the ability to evaluate inelastic rock behavior.IntroductionDuring the past three decades, many researchers have investigated standing support performance in longwall tailgate entries. Very little attention was paid to the middle entry of a threeentry longwall gateroad. As longwalls retreated, no personnel would travel the #2 entry, and the entry was considered part of the longwall gob. In response to recent mine disasters, regulatory agencies and operators have devoted more attention to these entries. Prior to the Upper Big Branch mine disaster, little or no secondary support was applied in these entries. Unlike secondary support in longwall tailgates, there is little empirical knowledge or quantified research specifically applied to secondary support in the #2 entry. This paper outlines initial steps used to develop a design methodology for secondary support in the #2 entry."

Jan 1, 2015

By R. Karl Zipf

Stress analysis programs such as MULSIM/NL, LAMODEL, MinSim 2000, and EXAMINE TAB are used in the mining industry to analyze stresses and displacements in coal mines, platinum mines, gold reefs, and tabular-type deposits. These relatively simple numerical models can efficiently simulate yielding and failure of a rock mass near a mine opening and subsequent stress transfer. The main input parameters for these models are a family of nonlinear stress-strain curves for the in-seam material. For many applications of these models, such as in coal mining, extensive field measurements and observations exist from which to estimate these stress-strain curves and calibrate the numerical models; however, such measurements are lacking for other types of mines. A three-step method is presented to determine nonlinear stress¬strain curves for boundary-element (BE) programs used in many mining applications. The method requires a suite of laboratory¬scale strength tests at various confining pressures. Note that this analysis uses laboratory-measured strength and modulus properties of alluvium. The dependency of the mechanical properties of alluvium on scale has not been established, although more tests are being planned. However, it is believed that the relative comparisons performed are valuable regardless of scale effects. First, the FLAC2D computer program is used to model the laboratory tests and determine cohesion (c) and friction angle (0) for a Mohr-Coulomb material model. Second, another FLAC2D model uses the c and 0 values to calculate vertical stress and strain around a single opening in the rock mass. This model calculates the stress-strain path of points at various distances from the opening boundary. Finally, based on these stress-strain paths, the stress-strain curves needed for a BE analysis are derived. This three-step method was demonstrated in a large, flat-lying underground test facility in very weak rock. The BE analyses agreed well with observations of failure at the test facility and provided a basis for evaluating the behavior of alternative layouts.

Jan 1, 2003

By André Vervoort

To learn more about the fundamental roof behaviour in South African coal mines, accurate underground measurements of roof deflection were conducted in bord and pillar panels during development and pillar extraction. To conduct these measurements a survey levelling technique was adapted. The overall system reading accuracy was established as being within 0,4 mm on a 15 m sighting distance. The underground sites were modelled and, for a roadway development, similar symmetrical curvatures were calculated by a linear elastic model, as were measured underground. In a pillar extraction panel, a significant amount of bed separation was measured and the roof underwent an a-symmetric movement due to the close presence of the mined out area at one side of the roadway.

Jan 1, 1992

By Markus Papst, Denise Millier, Daniel Beckers, Axel Preusse

"At an open-pit lignite extraction mine in Germany, groundwater has to be pumped over a large area, which leads to subsidence at the surface. As long as the geology of the area of influence is homogeneous, the subsidence is uniform and has marginal influence on buildings.Since the geology of many regions is characterized by faults, there are different rates of subsidence along those faults, which can lead to considerable consequences. Those different rates of subsidence on both sides of a geological fault are associated with the structure of the geology and soil mechanical properties. Horizons with various thicknesses and types of soil are affected differently by the groundwater pumping because of the offset of the faults, and thus react dissimilarly to dewatering.The smaller the grain of the geological horizon, the stronger the chance of shrinking, which leads to a stronger effect at the surface; therefore, dewatering impacts on clayey soil are different to those on sand and gravel. Regions consisting of meadows with turf inclusions are endangered as well; compared to the surrounding geology, those areas react in an entirely different way to water removal, which leads to immense differences in subsidence.The differences in area and respective subsidence impacts, as well as if it is possible to localize those areas, is an issue which needs to be analyzed. Furthermore, detailed mapping can help in the development of future forecasts about those subsidence differences and can also help with monitoring geological faults. In the context of subsurface spatial planning, this mapping has to be kept under review medium- to long-term.INTRODUCTIONThe utilization of underground mining is of increasing significance and of high interest, both for the common good and for future generations. For decades, humanity has been extracting resources from the subsurface, and salt, coal, lignite and water - just to mention a few resources - have been extracted from underground (Sailer, 2013)."

Jan 1, 2016

By Axel Preusse

Due to a political decision, German hard coal mining will come to an end in the year 2018. By then, there will have been more than 150 years of industrial grade mining activities. Located in the western part of Germany is one of the most densely populated areas of Europe. Multiple coal seams have embossed the earth?s surface up to 20 meters (21.87 yards), as mining has subsided. The aftercare of hard coal mining will consist of three tasks: groundwater management, polder management, and groundwater treatment. The Ewigkeitslasten (cost in perpetuity) at the current groundwater level has been determined in the past. The actual cash value is calculated to be about 12.4 billion euros (approximately 16.5 billion dollars). The cost of groundwater management is directly related to the groundwater level. Rising groundwater levels will reduce the cost of pumping water. Known effects of rising groundwater are uplift of the surface, emission of methane gas at the surface, higher risk of cave-ins, and contamination of drinking water horizons. Each of those processes produces cost in order to prevent negative consequences (e.g., uncontrolled methane emissions) or to handle reparations (e.g., damages caused by surface uplifts). In the long run, it is the goal to minimize the Ewigkeitslast. As a first step, all cost-generating processes are specified, and a cost type based characterization is performed. The objective of this case study is to identify key parameters to determine the quality of a cost-generating process (proportional cost, fixed amount cost). Afterwards, it is intended to specify the quantitative impacts of each parameter and to set up an optimization model to minimize the overall cost. The quantitatively specified parameters will form the base out of which the optimization model is created.

Jan 1, 2013

By Winton Gale

"Rock and coal fractures and micro seismic vibration are common occurrences during development mining. It is very uncommon for coal and rock to be propelled into the roadway during normal mining operations. However, such occurrences do occur and appear to require significantly more energy than is available from strain energy release during coal cutting. The sources of energy, which can contribute to the propulsion of coal from the face or ribs, are typically strain energy from the surrounding ground, seismic energy from a rapid rupture of the ground in the vicinity, or rapid expansion of gas from within the burst source area.The aim of this paper is to briefly review the bursts that could be related to strain energy or seismic energy. However, the greatest emphasis is placed on the effect that gas within the coal could play in moderate to gassy mines.It has been found that the bursts related to the expansion of gas can occur in coal and stone. The volume of gas involved in coal bursts is typically lower than in gas outbursts; however, the process is generally similar.INTRODUCTIONA coal burst is defined as a rapid expulsion of coal (and potentially gas) from the boundary of the roadway. The volume of a burst can be variable, but volumes above 10-50m3 are noted and cause significant disruption to operations.Rock and coal fracturing is common about roadways, particularly under the influence of elevated stresses, either tectonic or related to mining abutment stress. Shear fracture is very common; however, it is very uncommon that the coal is propelled from the face or ribs as a result of fracture of the material. The nature of rock fracture about roadways under elevated stress is presented in Figure 1.A burst requires energy to propel the coal or rock from the rib or face of the roadway. The depth of material impacted may vary from 0.5m to greater than 3m inside the roadway boundary. The strength of the ground in this zone is variable depending on the nature of the coal seam (or surrounding material). Typically, this material has significant residual strength as confinement increases into the ribside.The energy required to propel this material is typically in addition to that which is associated with normal fracturing about the roadway."

Jan 1, 2018

By Winton J. Gale

The subsidence over a longwall panel at Tahmoor Mine in the Southern Coalfield of NSW, Australia, was found to be approximately twice the size it had been in previous measurements. An investigation into the potential causes was conducted using computer modeling together with hydrological characterization and detailed geotechnical characterization of the strata. The abnormal subsidence was found to be consistent with localized weathering of joint and bedding planes above a depressed water table adjacent to an incised gorge. The study showed that other factors such as variation in stress field, joint zones, variation in rock strength and topographic factors did have sufficient impact to induce the abnormal subsidence. The results have significant implications to subsidence prediction in areas that may be prone to the phenomenon found at Tahmoor. Key indicators of the potential for this form of abnormal subsidence are presented.

Jan 1, 2011

By Jim Galvin

4 and 6 point timber chock constructions are used extensively on both a systematic and spot basis by Australian longwall operators to support tailgate roadways. In 1996, the School of Mining Engineering at UNSW published design and performance criteria for timber chocks constructed from Australian hardwoods. The research was funded by the Australian Coal Association Research Program (ACARP). In 1997, ACARP awarded funding for a stage 2 testing program. This testing focussed on examining the effect of using thinner timber elements in chock constructions to improve OH&S and comparing the full-scale performance of traditional 4 point chocks to Link-n-Lock constructions. It was established that chocks constructed from thinner elements have failure loads much less than thicker elements. However up to the failure loads of the thinner elements there was no significant difference in the response to convergence of chocks constructed from 25, 50 or 100mm thick elements. Chocks constructed from 150mm thick elements have a similar ultimate strength to the 100mm thick elements. However, they have a significantly lower resistance to load, thereby permitting more convergence to occur. There is more potential for chocks comprised of thin elements to be constructed 'out of plumb' and so suffer eccentric loading. The full scale testing program established that at any given level of convergence up to 10% strain, the timber in a Link-n-Lock chock generates twice the support resistance of the same quantity of the same timber in an equivalent size 4 pointer chock. On the basis of support resistance per cubic metre of timber, there is only a marginal difference in the performance of 1.0m Link-n-Lock chocks and 1.2m Link-n-Lock chocks constructed from select Blue Gum. The cost per tonne of support provided by a Link-n-Lock chock is effectively half of that provided by a 4 pointer chock of equivalent dimension and timber. Up to a strain level of 4%. Link-n-Lock chocks constructed from 1.2m long elements are slightly more cost effective than the same chocks constructed from 1.0m long elements. Thereafter, there is no significant difference in cost per tonne of support resistance. Beyond a strain level of about 4%, Link-n¬Lock chocks constructed from landscape grade Blue Gum are just as cost effective as Link-n-Lock chocks constructed from structural grade 4 Blue Gum.

Jan 1, 2000

By Ken W. Mills

The ground movements associated with underground coal mining and, in particular, longwall mining, are recognised to include horizontal subsidence movements, but the mechanics of the processes that cause these horizontal movements are not well understood. Over the last two decades, three-dimensional subsidence monitoring has become routine in Australia and has provided a wealth of measurements of horizontal movements caused by mining subsidence. These measurements and other sub-surface observations allow the processes that cause mining-induced horizontal movements to be inferred and, subsequently, verified. In this paper, the mechanics of the processes that cause horizontal movements, particularly those in sloping topography, are described and discussed on the basis of field observations. There are several processes recognised to generate horizontal subsidence movements. In flat terrain, systematic horizontal movements cause the surface to move initially toward the newly created goaf and, subsequently, in the direction of mining. Tectonic energy stored as horizontal stress is released by mining, and, when the horizontal stresses are high, the magnitude of this horizontal stress relief movement is large enough to be perceptible for some kilometres from the panel. In sloping terrain, there is an additional component of horizontal movement that occurs in a down slope direction. This movement, sometimes referred to as valley closure movement, has a magnitude that is typically much greater than systematic or stress relief movements.

Jan 1, 2014

By Joseph Hirschi, Naga S. Y. Tirumalaraju, Aditya Mishra, Anthony (Sam) J. S. Spearing

"Primary roof support in underground coal mines in the USA consists mostly of fully grouted passive rebar or grouted (partially or fully) tensioned rebar. Research conducted at two room-and pillar coal mines in the Illinois Basin and one longwall mine in Colorado monitored the performance of these passive and active rock bolts under similar geologic and mining conditions and found no significant initial loads in either passive or active rock bolts (Spearing et al., 2011). Active rock bolts showed significant loss of initial pre-load, although the exact reasons for this were not fully investigated. Subsequent laboratory testing has also shown that in weak rock, resin creep occurs, caused by slippage of the mechanical key between resin column and rock interface. These creep tests were studied in the laboratory in an effort to quantifythis phenomenon.INTRODUCTIONResin-grouted rock bolts are the first and main line of defense to counter roof and rib falls in underground coal mines of the United States. Rock bolts are categorized as active or passive. Active bolts are tensioned during installation whilst no (or limited) tension is applied to passive bolts, which need subsequent strata movement to generate reactive loads. During installation of passive bolts, some reactive pre-load may be generated by a significant up-thrust from the rock bolter boom.The selection of active or passive bolts is critical and is mostly dependent on the conditions and properties of the immediate roof (Unrug, 2009). This decision is frequently made based on personal experience, bias, and most recently cost. Active bolts are generally used in cases of highly laminated roof rock. When active bolts are tensioned, they develop compressive forces between these layers forming a beam, which helps to stabilize weak individual layers thereby increasing frictional forces between layers and decreasing effects of horizontal stresses. The fully grouted tensioned rebar system is high in stiffness as compared to mechanical bolts and provides higher surface area of contact along the length of the bolt due to the grout, which permits it to develop a strong anchorage mechanism."

Jan 1, 2015

By Steven Derycke, Stephen C. Tadolini, Anand Bhagwat

"The tensile and shear strength of intrinsic bolting support systems has always been a major concern of designers. A comprehensive laboratory testing program was designed to evaluate the tensile and shear strength of individual wires and completely wound PC-strand cables. PC-strand cables with smooth wires and the recent anchorage enhancement innovation of indentation were evaluated and compared. The testing protocol detailed in ISO Standard 15630 utilizes a mandrel system that was investigated at 3 different diameters which alters the wire to mandrel ratio from 2:1 to 9:1. The results demonstrate that the difference between smooth and indented wires is statistically insignificant when larger diameter mandrels are used, and that indentation does not adversely affect strand properties and performance. Insight into the shearing mechanism and evaluation techniques are discussed with the introduction of triaxial loading to describe the PC-strand tensile and shearing mechanisms. Another important result indicates that the shear strength of PCstrand cable bolting systems has a greater shear strength value than traditional steel bar bolting systems.INTRODUCTIONPC-strand cable bolts have proven to be a global cost effective ground control solution in metal/non-metal and coal mines. The inherent strength to weight ratio of cable supports, combined with flexibility has been used in underground entries that range from 20 to less than 1.2 m in height (65 to 4 ft). In coal mining, the systems are used as primary and secondary support installed both passively or actively with installation tensions that range from 38 to over 178 kN (8,500 to 40,000 lbs) . While cable can be specified in several diameters, the most predominant sizes in the US remain 15.2mm (0.6 in) and 18mm (0.7 in). The capacity of the systems defined in the ASTM 432-13 is 90% of the minimum strand strengths of 260 kN (58,600 lbs) and 320 kN (72,000 lbs), respectively.Cables are not only suitable to support vertical loads, but are also often used to effectively support fractured and jointed materials and can be exposed to shear forces across the wound PC-strand structure. In fact, Goris et al. reported that cable bolts placed across jointed surfaces could more than double the shear resistance. These results were duplicated for both smooth and rough jointed surfaces (Goris et al., 1996). An example of tensioned cable bolts used to support a fractured and sliding roof in a longwall tailgate entry is shown in Figure 1."

Jan 1, 2015

By Behdeen Oraee-Mirzamani

Since the advent of New Austrian Tunneling Method (NATM), shotcrete as a primary means of support in tunnels has been widely applied. It?s most important features are durability, speed of application and cost effectiveness. This paper introduces some tables that provide guidelines for the thickness of shotcrete required in some common situations of mine roadways. In order to devise such tables, two different arch sections, together with three different overburden types, were considered. Geotechnical parameters such as apparent cohesion and angle of internal friction of surrounding rocks were chosen, based on the five-category classification of Bieniawski. Two K0 factors (the ratio of horizontal stress to vertical stress) and an average rock density were utilized. Using numerical methods, 60 models were then devised in this way. By applying interaction diagrams of axial force and the bending moment for different thicknesses of shotcrete, appropriate shotcrete thickness for these models were calculated. The results of this research, as well as the methodology applied, can be used in mining roadway support design and all types of civil engineering tunnels.

Jan 1, 2011

By Christopher Mark

Preventing pillar line squeezes, massive pillar collapses, and coal pillar bumps is critical to the safe and efficient recovery of coal during retreat mining operations. To help prevent these problems, the U.S. Bureau of Mines has developed the Analysis of Retreat Mining Pillar Stability (ARMPS) computer program. ARMPS calculates stability factors (SF) based on estimates of the loads applied to, and the load-bearing capacities of, pillars during retreat mining operations. The program can accommodate various retreat mining scenarios including angled crosscuts, varied entry spacings, barrier pillars between the active section and old (side) gobs, and slab cuts in the barriers on retreat. It also features a pillar strength formula that considers the greater strength of rectangular pillars. The program may be used to evaluate bleeder entry designs as well as active workings. A data base of 130 pillar retreat case histories has been collected across the United States to verify the program. It was found that satisfactory conditions were very rare when the ARMPS SF was less than 0.75. Conversely, very few unsatisfactory designs were found where the ARMPS SF was greater than 1.5.

Jan 1, 1995

By Axel Preusse

Stowing or waste fill is common in the German mining industry since the beginning of mining activities, With increasing mechanization, flat and gently inclined seams (0 -- 18) were mined. These mines were located within the densely populated areas close to important infrastructures such as industrial complexes, roads, highways, railroads, rivers and canals. These buildings and infra¬structures were rarely protected against subsidence influences and other ground movements and dump capacities close to the mines were exhausted. For subsidence reasons and because of the low dump capacities pneumatic stowing methods were continuously developed and used in German longwalls until 1997. Due to techni¬cal standards and because of some restrictions pneumatic stowing in Germany is only used at a minimum seam thickness of 2.00 m and average costs of this method are $20 - 30 per ton. A significant reduction of the disturbance potential and by that a decrease in expenses for subsidence regulations due to reduced subsidence and ground movements could not be achieved. In this paper the experiences with pneumatic stowing in the Ger¬man mining industry are described. Possible subsidence reduction and economic aspects of pneumatic stowing are taken into account.

Jan 1, 2002

By Nathaniel Schaefer, Christopher Newman, Zach Agioutantis

"As mining reserves continue to be developed in deeper and more complex geological and geometric conditions, there has been an increased demand for underground mine designs to better reflect site-specific conditions, measurements, and observations with respect to ground control safety and stability. Current ground control design software are limited to a given device and data files generated can only contain a single design. However, with the growth of cloud computing and increases in internet access, even underground where permissible, web-based software applications allow for in-the-field calculations, as well as collaborations, from multiple users. webGroundControl (webGC) utilizes a multiple-tier architecture, building upon existing NIOSH ground control design software, more specifically ARBS, ALPS, and ARMPS. By providing operators the ability to access ground control design programs from any device, given an internet connection, webGC allows for on demand calculations to ensure underground pillar and roof stabilities with respect to current site-specific parameters, geometries, and geology. Through the development of new features, which aid in design analyses, as well as project collaborations, webGC provides the modern engineer with a more versatile ground control design tool for the improvement of underground health and safety. With the completion of the ARBS, ALPS, and ARMPS modules, this paper introduces potential users within the mining industry to the navigation and operation of the webGC application, as well as its ability to facilitate collaborations between operational personnel and planning engineers. The purpose of this paper is to raise interest in the web-based application before its official launch in Summer 2018."

Jan 1, 2017

By Gregory E. Smith

"Tensionable headed roof bolt systems are common in the U.S. mining industry. In the last 15 years or so, they have made a comeback as a hybrid system where a mechanical anchor is used in conjunction with resin. When such a system is used, it is common to use a spherical washer to comply with the requirements of 30 CFR Part 75.204(f)(8). This standard requires an angle-compensating device be used in installations where the bearing plate is offset from the roof bolt axis by an angle greater than five degrees. This paper evaluates system performance of four different traditional angle-compensating device/plate combinations including a new patented extruded plate/extruded washer system that improves overall load capacity and stretch.INTRODUCTIONA large western U.S. underground coal mine was using a fully grouted headed rebar system as their primary support. They had developed their component specifications over many years of working with suppliers to improve and optimize these components to integrate well as a system. As shown in Figure 1, the components included a patented 7 /8"" -diameter Grade 60 headed rebar bolt with a flange capable of full bar load (Walker, 2009) and a patented 8 in x 8 in Grade 3 extruded hole bearing plate manufactured by DieMatic Corporation.The mine decided to pursue a fully grouted tensionable system using a mechanical anchor as the tensioning device. Their primary goal was to eliminate the need for the roof bolt operator to secure (hold) the bolt during resin set time. An additional benefit was the increased initial tension on the bolt. To comply with the requirements of 30 CFR Part 75.204(f)(8), regarding tensioned roof bolts, they were required to include an angle-compensating device because a share of the bolt population would be installed at angles greater than five degrees from the perpendicular to the bearing plate. Also, to improve cycle time and torque/tension consistency, the mine desired to have the washers and anchors assembled at the factory. This required the use of a bearing plate with a center hole large enough to accommodate the 1-3/8-in-diameter mechanical anchor to pass though it during assembly by the roof bolt operator. The mine wanted to continue to use an extruded hole bearing plate in the tensionable system, and EMS was asked to propose a plate and angle-compensating device."

Jan 1, 2016