Search Documents

By Edward S. Custer

Recent investigations of mine roof falls have demonstrated that roof failures are generally associated with geologic conditions. The roof falls can be predicted by using the techniques of depositional modeling for the coal bed and roof rocks, and by lineament analysis. The ability to predict potential roof failure areas will allow the engineer and mine planner to develop a mine plan to avoid the roof failure areas and thus reduce overall mining costs. The ability to avoid roof failure areas also will permit maximum recovery of the coal resources.

Jan 1, 1981

By Jamal Hematian

Understanding the behaviour of rocks in a high horizontal stress field, such as that in Australia, is critical when analysing the stability of underground structures. This paper addresses the significance of the post-failure behaviour of rocks on the stability of underground structures which are under the influence of a high horizontal stress field. The research work was conducted through a combination of numerical modelling, laboratory testing and field investigation. A number of 2-D FE model of roadways were constructed based on the data obtained from laboratory testing and field investigations. The models were then analysed using three different solution techniques; simple linear-elastic, non-linear elastic-plastic and elastic-plastic with consideration of post-failure behaviour (softening model). Results indicated that the post-failure behaviour of rocks significantly influence the stress and displacement patterns around the roadway. The stress and displacement patterns as well as the extent of the yield zone around the roadway predicted by the softening model were in good agreement with that from the field study. Based on the results of the study, an appropriate support system has been suggested to govern the stability of roadways.

Jan 1, 1994

By Stephen P. Signer

A field test was conducted by the U.S. Bureau of Mines at the Cyprus Plateau Starpoint No. 2 Mine. near Price. UT. to study the support rock interaction mechanics. Twelve instrumented. fully grouted roof holts and eight sagmeters were installed in the roadway of a two-entry gate road to measure load changes and roof movements. Readings were taken during section development and as each longwall panel passed the test area. Loads that resulted from development of the en- tries were higher than would be expected if simple suspension of the roof rock was the sole cause of loading. When the first longwall face passed the test section massive beam behavior was exhibited over the entry and adjacent pillar. However, no significant localized bending was detected at any of the strain gauge locations. After the first panel passed the test section. all the roof bolts had at least one zone where the steel had yielded. Loading continued to increase. and when the face from the second panel was adjacent to the test section. 70 pct of the strain gauges at the 6-. 1%. and 30-in locations had passed the yield point of the steel roof bolt. However, even at these high load levels, the supporting pattern was sufficient to provide adequate reinforcement to the mine roof.

Jan 1, 1990

By Peter Altounyan

Goedehoop Colliery in the Witbank Coalfield of South Africa produces some 8 million tonnes of coal from fully mechanised room and pillar mining methods, using resin anchored bolts as roof support. Investigation of the quality of the installed bolts resulted in the finding that it was possible to pull out fully encapsulated roofbolts. This led to a drive to improve the quality of installation by making it easier to install a roofbolt correctly and more difficult to install incorrectly, whilst at the same time achieving high bond strength. The method of installation which was investigated, developed and implemented is known as 'spin to stall.' The roofbolt is pushed through the resin capsule to the top of the hole and then spun to mix the resin, until the increasing resistance to rotation exceeds the breakout limit on the bolt torque nut. The nut then runs up the bolt thread and is tightened to the roof as the drill stalls. This procedure is simple and avoids human factors such as non adherence to 'spin' and 'wait' times which contribute to poor installation with conventional methods. However spin to stall installation has been avoided in the past because of concerns over damage to the resin bond. This paper reports on the efforts made to investigate and understand the factors involved, and the progress made in overcoming the problem of resin damage so that the advantages of this installation method can be realised.

Jan 1, 2003

By Chris T. Franke

The Waste Isolation Pilot Plant is a deep underground facility mined in bedded salt interspersed with persistent clay inter- beds. The clay seams delineate beams of salt above and below the excavations which strongly influence excavation performance. This paper reviews available rock mechanics information relevant to improving drift stability by removing the roof beam. Conceptual deformation mechanisms, relevant field data, and numerical analyses were used to investigate the effects of mining the roof of the excavations along a clay seam. Finally, a case study that applies the results of this investigation is presented.

Jan 1, 1997

By A. Chrzanowski

The integrated approach to monitoring surveys is based on a simultaneous utilization of geodetic, photogrammetric and geotechnical measurements of displacements, tilts, strains and any other geometrical parameters of deformation. New techniques for the integrated surveys are being developed at the University of New Brunswick in cooperation with the Canada Centre for Mineral and Energy Technology. A telemetry system for continuous monitoring of geotechnical measurements under difficult climatic and topographic conditions has been constructed and successfully tested in a coal mining area in western Canada. A generalized method for analysing the integrated deformation measurements has been developed and applied in the test area to yield three dimensional empirical modelling of surface movements from geodetic, photogrammetric and tilt surveys. The most appropriate model can be chosen from a statistical assessment of several modelling possibilities. The empirical model of the deformation can be employed in a "calibration" of the prediction (deterministic) model of the ground movements. A computer programme for two- and three-dimensional finite element modelling of elasto-plastic deformations has been developed at UNB as a part of the integrated approach. The :EM has been tested in predicting deformation in the test area in difficult geological conditions which were associated with an extraction of a steeply inclined coal seam. The results gave good agreement with the actual displacements obtained from geodetic measurements and confirmed the existence of a suspected fault.

Jan 1, 1984

By Jinsheng Chen

The major functions of longwall headgate entries are to provide access ways to the outby submains or mains for coal transportation and to the longwall face for fresh air and for transporting men and material during longwall operations. Any roof control problems such as cutter roofs or roof falls in the outby headgate entries could result in significant production delays to the longwall face and may be a threat to miners' safety Under a thinly laminated immediate roof and a high horizontal stress field, even a longwall headgate entry that has an angle of less than 45 degree to the maximum horizontal stress may experience roof deterioration in the outby headgate if the longwall panel mining sequence and retreat direction are not properly considered. This paper attempts to analyze the causes of the roof control problems experienced in the longwall gate entries at our Cumberland and Emerald mines in Pennsylvania and to determine the optimal longwall panel mining sequence and retreat direction for the future mining area at Cumberland

Jan 1, 1998

By Lisa Burke

In underground coal mines, concrete block stoppings are widely used to control mine ventilation. Although stoppings are not intended as roof support, they are subjected to roof to floor convergence, and may fail as a result of this loading. Premature failure of stoppings can significantly affect mine ventilation, limiting the amount of fresh air reaching the working faces and increasing the risk for methane explosions. Softening materials are often used in stoppings to reduce the damaging effects of roof to floor convergence. However, to date, research has not focused on the behavior of stopping construction materials subjected to roof or floor loading, leaving the design process to trial and error. A combination of numerical simulations and large scale physical tests were employed to develop a scientific understanding of stopping performance. The first series of physical models were constructed using standard CMU (concrete masonry unit) blocks and tested in a load frame. The behavior of these walls was simulated with a distinct element model. A key finding was that very small variations in block size and irregularities in block shape significantly affect wall performance. These variations, which are inherent to the type of blocks typically used underground, create stress concentrations that initiate the failure of stopping walls. A second series of models employed concrete stoppings that incorporated woos planks, a shredded wood material, and foam planks like those commonly used underground. Numerical models were again able to match the physical test data. Analysis of the softening layers used in stopping construction indicated that the strength and stiffness of the material relative to that of the wall is crucial in determining the amount of roof to floor convergence the wall can withstand prior to failure. The product of this study is a numerical model that can be used to evaluate the performance of stopping materials and different wall geometries in a controlled environment. Testing was done in a laboratory setting with walls constructed on flat, parallel surfaces and subjected to uniform loading at a constant rate. Parametric studies with the model indicate that in this ideal environment it is possible to control the amount of vertical displacement the stopping can withstand by adjusting the number of softening layers built into the wall and the thickness of the layers. Additionally, under these conditions, the position of softening layers within the wall appears to have little effect on the amount of displacement walls can withstand prior to failure.

Jan 1, 2004

By Joachim Leonhardt

Hundreds ofbolt-indicators were already used successfully in the German deep hard coal-mines to increase the safety and economy. The bolt-indicator offers the simple possibility to show roof-bolt (anchor-) loads. to indicate weak points as well as to optimize the anchor density and the dimension: The bolt-indicator is mushroom shaped and consists of coated metal. It is inserted between the anchor plate and the flanged nut. The loads appearing at the anchor are transferred to the bolt- indicator and can be recognized visually at the cylindrical part by the amount of the surface coating. Examples are used to clarify the application aims, operation and usage of the bolt-indicator and its yielding advantages in practice.

Jan 1, 2001

By B. G. D. Smart

The development of a softwood alternative to the hardwood chockpiece used to build the waste-edge breakers commonly incorporated in gateroad packs is described. The results of laboratory tests on softwood prototypes and two underground trials are presented. The results of the last trial suggest that a viable alternative chockpiece has been designed, offering advantages over availability of wood, weight and given reduced wood content, price.

Jan 1, 1992

By Binchuan Zhang

The combined reinforcement system (CRS) combines the strengths of roof' bolting, resin-anchored cable bolt, and chemical grouting to effectively control the deformation of the strata surrounding an extremely poor entry. It is easy to implement and fast in installation. It is one of the systems that are suitable for the reinforcement and maintenance of extremely poor entries.

Jan 1, 2001

By Jay Hilary Kelley

This paper proposes a modification of longwall roof support to meet new difficult mining conditions that are anticipated in the future. A gob canopy is a movable appendage attached on the rear of a longwall shield to counterbalance the troublesome forward downward force couple (FDFC). The gob canopy can be swung in both vertical and horizontal directions, powered by hydraulic cylinders. Several functions and applications are de- scribed

Jan 1, 1997

By Mikko Ahola

This paper describes recent innovative analyses conducted by the Bureau of Mines to demonstrate the application of the boundary-element method in evaluating the effectiveness of caving chambers or sacrificial entries to relieve the stress conditions initiating cutter roof failure in underground coal mines. The analysis assumes that cutter roof failure results when the shear strength of the roof rock at an entry corner is exceeded by the applied shear stress. The applied shear stress is due to large differences between the horizontal and vertical in situ stresses known to exist in many coal mining districts experiencing cutter roof failure. The results of boundary-element analysis suggest that driving an arched lead entry in advance of adjacent rectangular entries and allowing it to cave significantly reduces the difference between the principal stresses at the corner of the rectangular entry, thereby lowering the maximum shear stress. Slippage of the immediate roof along horizontal bedding planes into the caved entry is shown to further reduce the stress conditions in adjacent entries. Practical applications of this stress control technique to longwall and room-and-pillar mining are discussed.

Jan 1, 1987

By Yao Yuping

The strength and deformation of more than two hundred coal samples have been tested in the condition of triaxial compression. The regression equation showing the relationship between coal strength and pressure in the pores as well as confining pressure, was obtained. The appropriate calculation for stress-strain curve was carried out. Further, an analysis shows the variation of coal strength and its modulus of elasticity in methane medium.

Jan 1, 1992

By Brian Daniels, James Farroni

"Draw rock (small rock that forms/falls when bolting the roof and/or rib) is the cause of numerous injuries annually. These injuries result in lost work hours and low morale. The report below explains how ""Mine Safe Draw Rock Shields"" (Pans) are used in an underground operation. This report will chronicle the application of these pans in a Southern West Virginia coal mine along with testing data that measures their effectiveness. Since the introduction of these pans in 2002 the amount of reportable accidents relating to draw rock has decreased by 80%. The report below reinforces that perimeter contact is critical to the performance of these pans. In addition the strength of these products at the perimeter will determine their effectiveness. The results of the testing data outlined in this paper, along with the physical records at the study mine, confirm that the use of pans has significantly reduced draw rock falls at this facility.BACKGROUNDSupplemental support is defined as ground control that is used in addition to required support in an underground mine. Some examples of supplemental support are:• Pans• Mesh/Geogrid• Mats• Half Headers• Boards• ChannelA typical roof condition that warrants the use of pans is when loose small rock is dislodged while bolting. If the top is very scaly (loose, thin rock) additional supplemental support can be used in conjunction with pans such as mesh or geogrid (See Figure 1). Pans will provide protection where used and approximately 12 in (250 mm) out from perimeter. This is achieved by contact with a surface which will put scale in tension up to 12 in (250 mm) from perimeter of pan.INTRODUCTIONThe ease of applying a roof support system is critical to effectively operating a deep mine. Figure 2 shows how a pan is installed in conjunction with a roof bolt and bearing plate. The Mine Safety and Health Administration (MSHA) requires that supplemental support cannot decrease the performance of required support. The goal of using all supplemental support is to provide additional safety for the miner which equates to increased productivity.The ability of skin control products to contact a surface is the single most critical characteristic (Figure 3 and Figure 4). If the material does not contact the surface it cannot be effective. Therefore, the flexibility, design and proper installation of the products are critical in determining their effectiveness. Figure 5 shows the proper installation of the roof pan.To reiterate, all skin control must be applied in conjunction with a roof bolt and ASTM approved bearing plate as shown in Figure 4."

Jan 1, 2010

By B. (Mamas) Das

A project to evaluate the suitability of point Load strength tests for testing and classifying coal measure rocks for coal mining application was initiated by Canada Centre for Mineral and Energy Technology (CANMET). A summary of this study with emphasis on the important findings is presented in this paper. The instrument as used in this study is a Robertson Research Rock Strength Index Log. Because of the variation in the correlation ratio between uniaxial compressive strength and point Load strength index for hard rocks and soft rocks it was decided to establish this corre¬lation initially on cement concrete specimens specially prepared for this purpose following ASTM specifications. These specimens are expected to represent soft rocks and at the same time would be of uniform quality. Once a general trend of this correlation was established tests were performed on coal and rock samples from the sub-bituminous and bituminous coalfields in Canada. The most important results may be stated as follows: (i) Generally, the common value of the ratio between the uniaxial compressive strength and the point load strength index ranges between 8 to L4. (ii) The Robertson Research Rock Strength Index Log proves to be quite suitable for testing sandstone, siltstone and some coals from the bituminous coalfields but problems have been experienced when testing weathered samples or samples from the sub-bituminous coalfields. (iii) In some cases tests were successful if Larger samples from weathered zones or from sub-bituminous coalfields were used. However, a magnified load gauge for 0-3KN or 0-5KN is expected to be the best solution for soft and weathered rocks in most of the cases. Some mudstones and some rocks from weathered zone do not appear to be suitable for these tests. This aspect of the study is still under investigation. (iv) Deterioration of rock properties due to weathering has been determined through tests on samples collected from weathered and unweathered samples.

Jan 1, 1984

By Ruixiang Gu

The de-confinement mechanisms of unstable failures as they occur in deep coal mining conditions are investigated using a distinct element numerical modeling code. The Mohr-Coulomb and continuously yielding joint constitutive models were used to study the compressive failures in coal and slip behavior of coal-rock interfaces, respectively. The effect of strength variations within interfaces on the failure mechanism of mining faces is also studied. The stability of interface slip failures was found to have a significant role in the failure mode of coal sidewalls. When the interfaces experience stable slip failures, the sidewalls are more likely to fail in a stable manner. With occurrence of unstable slips at interfaces, unstable compressive failures of sidewalls are triggered. The numerical modeling results support the proposed de-confinement mechanisms and emphasize the importance of including the coal-rock interface behavior in the analyses of unstable compressive failures. The significance of the proposed mechanisms in underground mining conditions is that rock discontinuities with large cohesion drop can become potential factors, inducing unstable compressive failures at ribs and mining faces. Therefore, the de-confinement mechanisms should be taken into consideration in mine design.

Jan 1, 2014

By Peng Zhang

In previous research, the laminated overburden model from the LaModel program was effectively integrated with Analysis of Retreat Mining Pillar Stability (ARMPS) through ARMPS-like input to create a laboratory version of the new ?ARMPS-LAM? program. This program takes the basic ARMPS geometric input for defining the mining plan and loading condition, and then automatically develops, grids, runs, and analyzes a full LaModel analysis of the mining geometry to output the section stability factor (SF), all without further user input. The initial ARMPS-LAM results were encouraging with a case history classification accuracy of 55% to 71%; however, a few of the input variables that were nominally included in the SF calculation showed independent significance in the classification accuracy. Therefore, in order to further improve the accuracy of the ARMPS-LAM program, an investigation of the SFs calculated by the new ARMPS-LAM program and the ARMPS program is detailed in this paper. The initial results of a linear correlation between the ARMPS-LAM SF and the ARMPS SF showed a strong correlation (R2 = 0.88), with the ARMPS-LAM SF averaging about 8% higher. The difference in SFs between the programs were further investigated, and, ultimately, the results indicated that the laminated overburden model as implemented in ARMPS-LAM distributes relatively more load on the section pillars for depths less than about 1,000 ft and less load for depths more than 1,000 ft. The results of this research highlight the potential for improving the ARMPS-LAM program in the future by implementing a more accurate loading calculation on the section pillars.

Jan 1, 2014

By Jun Lu, Greg Hasenfus

"In this paper, the mining experience and challenges for the first right-handed longwall panel in the Pittsburgh seam are introduced. The longwall headgate T-junction experienced very high face convergence (up to 2 feet), accompanied by roof sag, floor heave, and rib loading. The headgate convergence was so large that, in a few places, it threatened longwall retreat and ultimately required the bottom to be re-graded.Different underground instruments, such as a roof scope, de-gas drill, tell-tale, laser meter, and Borehole Pressure Cell (BPC), were employed to explore the roof geology and to monitor the entry convergence and the stress changes in the pillar. In addition, the impact of other geologic factors, such as large overburden depth, laminated sandstone roof geology, soft floor, and large headgate equipment, were also analyzed. Subsequently, geotechnical solutions were provided to avoid or mitigate the impact of these challenging geologic factors.INTRODUCTIONIt is well known that high horizontal stress will affect the stability of roof, floor, and ribs within underground mines. In general, the headgate entries will experience stress concentration for the right-handed longwall face. On the contrary, the stress concentration will be in the tailgate entries for the left-handed longwall face (Hasenfus and Su, 2006). Without the stress shadow, the stress concentration in the headgate for the first longwall panel may be more significant (Figure 1).A mine in the CONSOL Pennsylvania Operation was extracting the first right-handed longwall panel in the Pittsburgh seam, which created high horizontal stress concentrations at the longwall headgate. Because of concern over soft wet floor within the syncline, floor coal had been left in place on development. Early on, upon retreat, the longwall headgate T-junction experienced very high face convergence, accompanied by roof sag, floor heave, and rib loading. The floor heave was exacerbated by the presence of floor coal, which buckled upward near the center of the beltline. Roof movement was occasionally aggravated by laminated roof conditions, but was kept in check by aggressive supplemental support including cable bolts, yielding props, cribbing, and roof mesh. Rib bolting and rib mesh helped to further maintain the entryway stability by keeping sloughage at a minimum. Nevertheless, despite the heavy support, headgate convergence was so large that, in a few places, it threatened longwall retreat and ultimately required the bottom to be re-graded."

Jan 1, 2018

By Deren Zhu

The principle of roof control in longwall mining is to control main roof fractures so as to reduce roof weighting, plus reasonable and effective design of supports to reduce the convergence and premature caving of the immediate roof. This paper introduces a comprehensive test for better roof control based on the geological conditions of coal seam No. 16 in Zaozhuan Colliery, China.

Jan 1, 1990