Search Documents

By Anders Sellgren, K. Hansson, A. Jedborn

In the mining industry, conversion of fine particles into a slurry is often part of the normal processing of the ore. Therefore. from a system's point of view, slurry transportation would be considered as a natural alternative, all the way from the working face to the final processing. In underground mines, there is sometimes a considerable inflow of ground water that has to be pumped out. When the mine dewatering installations are integrated with a hydraulic hoisting system, the cost of power needed to pump out the ground water can be excluded from the cost of hoisting, compared with other modes of transporting the solids to the surface. The chief advantage of hydraulic hoisting is that the hoisting capacity can be increased at comparatively low total cost without necessitating the sinking of new shafts. Alternative examples include deepening of the existing mechanical hoisting system, truck, or conveyor belts transport in ramps to the present level. These often become very expensive. The economic effectiveness of hydraulic hoisting and hydraulic design considerations have been discussed by Kostuik (1965) and Sellgren (1985, 1986) for both small shallow mines and large deep underground mines. Objective and scope The objective of this study was to demonstrate the feasibiliy of hydraulic hoisting in hypothetical examples of mine deepening. Underground grinding to a maximum particle size of about 700 um (about 25 mesh) is considered. The pumping of ground ore products with positive displacement plunger or membrane type of pumps at working pressures of up to 15 MPa (2200 psi) is a thoroughly tested technique (Venton, 1986). Hydraulic hoisting system A hydraulic hoisting system is described schematically in Fig. 1. The ore is mined, handled, and crushed conventionally. It is then ground wet underground. The slurry is then temporarily stored in an agitated tank and pumped to an agitated receiving tank on the surface. The ore is then further processed in the concentrator. The capacity of a pipeline is very high. For example, an annual production of 500 Kt (550,000 st) of ore can be handled in a 100-mm-diam (4-in.-diam) pipeline. Systems layout - economic effectiveness Schematic mine layouts are presented that represent situations where hydraulic hoisting often is the most economical alternative. A situation where the ore is trucked to the level of the existing hoisting system is shown in Fig. 2 (following page). With hydraulic hoisting, only a shaft for ventilation, pipe- line, and personnel are needed. In a first phase (Fig. 2). a hydraulic hoisting installation with crushing and grinding units, storage facilities, and pumps has been located at a level of about 400 to 600 m (1310 to 1970 ft) below the surface. With further development of the mine, the hydraulic hoisting

Jan 1, 1990

By Ralph Loyd

One of the principal responsibilities of the California State Geologist is to provide local governments with maps and information regarding mineral resource occurrences within their jurisdiction. The primary objective of this effort is to furnish basic data that is essential in planning for and accommodating wise development of mineral deposits that are important to the economic well-being of the region, state, and nation. Local government agencies are required by law to incorporate the information provided by the State Geologist into their general plans and formulate mineral resource management policies that emphasize conservation and development of mineral deposits. The Mineral Land Classification program was initiated by the State Geologist in 1977 under authority of the California Surface Mining and Reclamation Act (SMARA). To date, about 33,000 square miles of land have been classified for mineral resource potential. Most of the mineral land mapping has been conducted in three principal areas: (1) metropolitan areas of the state where urban encroachment has greatly diminished available supplies of construction aggregate; (2) Sierra Nevada foothills, a region that is undergoing dramatic population increases; and (3) the Mojave Desert and Great Basin regions, where large Federal land withdrawals are pending that could preclude mining. Mineral land classification studies address the overall mineral potential of a region through the identification of local and regional geologic factors that control or influence the formation of mineral deposits. These studies are field-intensive surveys that enable project geologists to gain first-hand knowledge about the nature and distribution of mineral deposits in a given area and portray that information accurately in map form. This paper summarizes the progress made in the Mineral Land Classification program in the metropolitan, Sierra Nevada foothills, and the Mojave Desert/Great Basin regions of California. Selected projects from each area are discussed in detail.

Jan 1, 1995

By M. S. Klima, A. P. Pinkerton

Solid-bowl (decanter) centrifuges are used extensively to dewater slurries in a wide range of industries. However, the application of decanters as classification devices is not as common. In this study, the performance of a continuous, pilot-scale, solid-bowl centrifuge was evaluated when classifying an ultrafine coal slurry containing nearly 60% material less than 10 µm. The test conditions included centrifuge howl and scroll speeds, volumetric feed rate, solids concentration and pond depth. Centrifuge performance was evaluated using size selectivity curves and the corresponding performance parameters, along with product yields and solids concentrations.

Jan 1, 2002

By P. K. Chatterjee

Before coal can be extracted from surface or underground mines, approval must be obtained from state and federal authorities. Permitting is the application process through which such approval is sought. The application includes en environmental impact statement Which focuses on Such topics as subsidence, toxicity of acid mine drainage, pollution levels of rivers and streams, post mining reclamation, and the effect on the hydrological balance of the area. The permitting procedure is extremely time and labor intensive, and requires extensive interdisciplinary knowledge. This paper examines a LISP based permitting procedure which will help to reduce the time taken to prepare and review a permit application.

Jan 1, 1986

By M. S. Celik, G. Onal, S. Atak

The beneficiation of boron minerals flotation with well defined systems has been only slightly, investigated in the literature. The difficulty arises from fact that boron minerals cover a spectrum of solubilities. Colemanite (a calcium-containing, relatively insoluble, boron mineral) and borax (a highly soluble boron mine, have been used to exemplify the flotation of boron minerals. Using sodium dodecylsulfonate (SDS) and dodecylamine hydrochloride (DAH), the floatability responses of these boron minerals are considerably different. This has been ascribed to variations in the solubilities of boron minerals and the presence of cations in the lattice structure. In study, flotation tests and zeta potential measurements used to determine the flotation mechanisms of boron minerals.

Jan 1, 1994

By S. K. Kawatra, T. C. Eisele

In many mining operations, particularly northern open-pit mines, large seasonal variations in grinding slurry temperature can occur. It is shown in this paper that this temperature shift can cause a winter-time loss in autogenous grinding efficiency of as much as 20% if it is not controlled. Laboratory experimentation indicates that much of this effect is due to increases in slurry viscosity as the temperature is decreased. An additional effect may result from changes in rock strength upon freezing, for which possible mechanisms are discussed. However, no effect clearly resulting from rock strength changes has been definitely confirmed.

Jan 1, 1992

By John W. Tieman

Coal is a term applied to vegetable matter (trees, grasses, etc.) which was subjected to heat and pressure through geologic ages. This resulted in a change in both the physical and chemical properties. Because its chemical composition is variable, geologists classify coal as a heterogeneous mineral rather than a homogeneous mineral. Peat represents the initial, unconsolidated stage in the development of coal. This coalification continues with time and the application of temperature and pressure to lignite, subbituminous, bituminous, and anthracite toward the theoretical graphite end member.

Jan 1, 1981

By K. Kim, T. M. Yegulalp

A numerical model is being developed to assess the enhancement of ore permeability by improving fracture connectivity with micro-hydrofracturing. As part of this project, a generic two-dimensional percolation model was developed to test the impact of various field conditions on permeability. Field data from Cyprus Minerals' Mineral Park mine was used to establish the statistical properties of the observed fracture systems. Results of statistical analyses of field data and examples of the use of the percolation model are presented

Jan 1, 1997

By M. J. Klishis

This paper presents the findings of a study on roof bolter's hazard exposure. A "microanalysis" of accident data was combined with ergonomic observations of roof bolter operators to categorize bolting-related injuries, and, from this, a checklist was constructed. Bolting-related problems were identified as situations that could expose bolter operators to hazards. Approaches to avoid these situations were applied at six mining operations to evaluate specific problems in root bolting operations. The research emphasized the importance of analyzing worker behaviors in the context of mining situations and equipment-design problems that lead to human-error accidents.

Jan 1, 1996

By B. K. Parekh, R. H. Mehta

The handling of fine coal is an important issue for both the coal and utility industries. Reconstitution of fine coal in the form of pellets or briquettes would be desirable if it could be done economically. This paper evaluates the effectiveness of three binders, asphalt-emulsion, corn starch and Brewex, informing pellets of ultrafine clean coal. It was found that asphalt-emulsion and corn starch were not effective binders. However, the use of Brewex resulted in pellets that exceeded all of the minimum quality requirements for coal pellets.

Jan 1, 1997

By K. L. Kasperski, M. T. Ityokumbul

The effect of reaction conditions on the desulfurization of oil-sand coke residues was studied. The variables investigated were temperature, reaction time, heat transfer resistance and mode of caustic soda addition. The results show that oil-sand coke desulfurization increases with temperature, reaction time and heat-transfer rate. In an oxidative environment, coke combustion during molten-caustic leaching (MCL) commences at temperatures above 500 °C. The mode of caustic addition has no effect on coke desulfurization.

Jan 1, 1996

By Robert M. Cox

The principal factor that must be determined for the effective design of a coal mine roof bolt support system is the maximum stable tension that can be developed with a given bolt assembly in a particular roof rock. There are four basic types of roof bolt anchorage techniques available: (I) the splitwedge; (2) mechanical expansion units; (3) resin point anchors or grouted expansion units; and (4) the cone shell which is placed in a reamed hole. A study of this problem has been made which includes theoretical analyses, laboratory experiments and field tests. A static free-body analysis of each of the anchorage techniques has provided formulas for predicting the anchorage capacity for a particular rock from the results of standard pull tests. The formulas also provide an insight into the anchorage mechanism of technique and allow for a comparative evaluation of the methods for design purposes. The theoretical analyses also indicate clearly the pertinent variables affecting the anchorage mechanism of each method.

Jan 1, 1977

By G. Olson, T. Mudder, T. Clark

An evaluation was made of an innovative chemical approach for controlling the biotic portion of sulfide oxidation of tailing and waste rock using thiocyanate. This lipophilic anion is selectively toxic toward acidophilic bacteria, including those that oxidize metal sulfides. Sulfidic materials from precious metal and base metal mining operations were treated with thiocyanate solutions and subjected to accelerated laboratory weathering at 1 to 50 kg scale in humidity cells, trays, and columns. Initial field trials were conducted at 13.6 t and 100 t scale. Thiocyanate at relatively low concentrations reduced ARD from 50% to over 99%, depending on the sample and specific ARD parameter measured. Test work also was done with phosphate as an agent to coat reactive sulfides, further reducing their oxidation by biological and chemical reactions. The combination of phosphate and thiocyanate treatment is the basis for a potentially comprehensive approach to ARD prevention and control. Additional research and pilot testing are underway.

Jan 1, 2004

By Richard C. Harris

Substantial economic benefits exist today for fine coal preparation and improved technologies coupled with more stringent air quality standards should increase those benefits in the future. The costs of cleaning can be determined with reasonable certainty with proper consideration given to mining methods, plant feed characteristics, refuse disposal and marketing impact. The benefits cannot be as accurately determined but include impact on generating capacity, plant maintenance, emission standards, slagging, fouling, transportation, and handling. Site specific cleaning offers particular benefits in some situations to tailor the preparation plant facility to boiler characteristics. Improved communications and methodologies need to develop to allow the coal producer and the coal user to clean coal to the degree that results in the lowest overall cost for electrical generation.

Jan 1, 1988

By N. M. Cheimanoff

GEOCAD is an ambitious research program aimed at the development of a computer based system assisting the geologist and the production or planning engineer. BONANZA, its mining part, is a computer production scheduling tool (short to medium term) of particular relevance to complex orebodies. The principle is to simultaneously use a powerful information management system (CAD potentialities) and small expert modules integrating the exploitation context and the engineer's knowledge (Artificial Intelligence tecniques). As an illustration, a module of mineable block determination for underground exploitation is discussed.

Jan 1, 1989

By Cliff G. Paton, Sheldon B. Bland, Roger E. Melley

This paper looks at four critical lubricants used in the conveyor systems of the northern Albertan oil sand facility. The requirements for the lubricants used in the electric motors and gear boxes of the drive systems, the pulley bearing and the idler bearings are discussed in terms of the applications and the environment. A number of developments that have occurred in recent years are presented. Data from the field and from custom designed testing in the laboratory are used to support the role of simulation testing in problem solving in this area of technology.

Jan 1, 1996

By Bradford F. Townsend, Gary Peach, Roger Rothenburger

From the experience of the authors on recent large infrastructure Design-Build projects this paper reviews major lessons for Contractors and Owners in the delivery of large Design-Build infrastructure projects and some major pitfalls and warnings to both Owners and Contractors. The paper is written from both the Design and Construction perspective. A case history is presented that details the approach employed to ensure a quality project consistent from the initial design phase through construction and outlines the strategy used to guide the Design-Build process to an acceptable completion. Suggestions are made for Contractors and Owners for handling the Design and the Construction elements of Design-Build contracts.

Jan 1, 2003

By R. L. Lewis

The White Pine Mine is a large underground copper mine located in the Upper Peninsula of Michigan. A numerical ground water flow model of the White Pine Mine was constructed to evaluate potential engineering controls that would reduce the rate of mine-water discharge after closure. Of the passive controls evaluated, the placement of bulkheads within the mine workings was predicted to offer the greatest benefit, reducing the rate of discharge by as much as 35%.

Jan 1, 1997

By M. J. Gula, S. S. Xue, E. P. Horwitz, J. T. Harvey

A study was conducted to control iron in copper electrolyte streams using Eichrom Industries' new monophosphonic/sulphonic acid resin. The resin strongly and selectively extracts ferric ion over copper and cobalt from highly acidic copper electrolytes. The resin has a loading capacity of 27-g/L iron and can be readily regenerated. In addition, the new resin can easily be synthesized using commercially available starting materials. This paper presents the experimental results for iron control in copper electrolyte streams using the new resin and discusses its potential applications to other hydrometallurgical streams.

Jan 1, 2002

By Rilung Xu, Jerry C. Tien, Jian Liu

As underground mines become deeper and ventilation networs more complex, ventilation data becomes more complicated and voluminous, making timely ventilation planning and necessary changes more difficult. Oftentimes, ventilation engineers have to rely on special techques using graphs and schematic maps to carry out necessary ventilation planning [1, 4, 5, 6, 9, 10, 11, 12]. A different graphical method, similar to that reported by Taminago and Isobe [10], has been developed in China [13]. This method uses a two-dimensional diagram drawn from available ventilation survey results. It combines both the customary pressure-quantity diagram and ventilation schematic map, and can greatly expedite the interpretation of survey results, facilitate ventilation system design, short and long-range planning, and emergency planning.

Jan 1, 1993