Search Documents

By Lynn B. Hales, John A. Herbst, Thomas L. Gabardi

A system for a continuous determination of the charge volume of grinding media in ball mills and SAG mills has been developed. The system, comprised of a unique measurement device and a model based Kalman filter algorithm, determines grinding media level within a mill and calculates media and liner wear rates. The signal from an instrumented washer mounted on the exterior of the mill shell is used to provide the measurement that, along with mill power and on-line models for media mechanics, result in estimates of mill parameters that can be used in media addition control strategies. Data are presented for a 12.5 x 15 ft. ball mill.

Jan 1, 1990

By David Jenkins

Grefco Inc. operates two diatomite mines in the western Santa Ynez Mountains. The larger of the two mines, the Palos Colorados Mine, is located approximately seven miles southeast of Lompoc. The Miguelito Mine is located about two miles south of Lompoc on the west side of the Miguelito Canyon. Diatomite from the Palos Colorados and Miguelito mines is trucked to the Grefco plant at Lompoc for processing (Figure 1). HISTORY Grefco, Inc. evolved from the originating Dicalite Company which in 1929 began operations at the Walteria plant in the Palos Verdes Hills south of Los Angeles. In 1942 Dicalite leased the Palos Colorados mine at Lompoc. In 1944 the Dicalite Company was purchased by Great Lakes Carbon Corporation.

Jan 1, 1995

By J. J. Schwoebel

Resource Enterprises Inc. (REI) is exploiting the coalbed gas resource by working in unison with active underground mining operations. At REZ7s pilot project at the Soldier Canyon mine, Carbon County, UT, RE1 has drilled nearly 15.25 km (50,000 ft) of horizontal in-seam and slant boreholes during the initial two years of drilling activity. Produced gas has been sold to a natural gas transmission company on a continuous basis since mid 1983.

Jan 1, 1988

By A. M. Marabini, G. Belardi, E. Spaziani

The objective of this research was to investigate the possible application of integrated circuits to the concentration of talc from the Valmalenco mine, located in northern Italy. The investigation was aimed at producing a high-grade product (low in impurities such as iron and carbonate) that would be suitable for industrial applications. Because of the presence of accessory minerals, the talc concentrate from this ore is not, at the present time, suitable for industrial applications.

Jan 1, 1996

By Marietta Canty

Results are presented that were gathered during field-scale testing of an innovative technology, sulfate-reducing bacteria (SRB), designed to treat and control acid mine drainage (AMD). The project was performed under the Mine Waste Technology Program (MWTP), which is funded by the U.S. Environmental Protection Agency (EPA) and jointly administered by the EPA and the U.S. Department of Energy through an Interagency Agreement. The MWTP is implemented by MSE Technology Applications, Inc., located in Butte, Montana. A field-scale test is described in which the subsurface workings of an abandoned mine were used as an "in situ biological reactor."

Jan 1, 2000

By P. D. Roa, O. Noirot, H. Owens, D. E. Walsh, J. R. Mokka

Over a period of eight years (1989 through 1997) the Mineral Industry Research Laboratory (MIRL) at the University of Alaska, Fairbanks, AK, has investigated the effects of temperature, residence time and particle size on the degree of low-rank coal (LRC) upgrading for a nonevaporative, hydrothermal drying process, also known as hot water drying (HWD). The following three Alaskan LRCs were used in this study: Usibelli coal (Seam No. 4) from the Nenana Coal Field, Little Tonzona coal from near McGrath, and Beluga coal from the Beluga-Yentna field on the west side of Cook Inlet. Replicated factorial tests were conducted. Experimental results indicate that most of the low-rank coal upgrading via HWD occurs rapidly within the first 10 to 20 min of residence time. Thereafter, the upgrading process slows down, and more than 100 min of additional residence time is required to produce percentage increases equivalent to what was achieved in the first 10 to 20 min. The properties of the hot water dried products were very sensitive to process temperature. Calorific value, carbon and oxygen contents, equilibrium moisture levels and Hardgrove gindabilities all appear to change linearly with temperature within the 275°C to 325°C (525°F to 61 5 OF) range.

Jan 1, 2000

By J. T. Crawford

Computer techniques for open-pit limit analysis were introduced into Kennecott Copper Corp. (KCC) during the early 1960's. The first computerized approach used block matrix mineral and economic models, and a removal increment mining simulator. A detailed description of the approach was published in the May issue of Mining Engineering (Carlson, et al., 1966) and also in Chapter 30.3 of the SME Mining Engineering Handbook (Pana and Davey, 1973). Since then, many refinements have been made to improve the system and the resulting pit limit design. The fundamentals, however, generally remain unchanged. Computerized open-pit limit analysis is presently used by Kennecott's open-pit copper properties and by the Quebec Iron and Titanium Corp. The system and the fundamental evaluation techniques it represents are cornerstones of all open-pit mine planning activities within KCC. This case study describes a typical example of open-pit limit analysis within KCC. The case involves a copper sulfide porphyry deposit with additional minor amounts of molybdenum, gold, and silver. The ore-grade mineralization within the pit design will be mill feed for a sulfide ore concentrator, and subore grade mineralization will be classed as waste and placed on dumps. The contributions to production and profits from dump leaching are insignificant, having minimal effect on the pit economics and design, because the material responds poorly to leaching solutions.

Jan 1, 1979

By Roger D. Sharpe

The United States Gypsum Company operation at Plaster City, in Imperial County, California, consists of the largest gypsum quarry in the United States, a company-owned, narrow-gauge railroad and wallboard and plaster manufacturing facilities. A variety of gypsum products, including many types of wallboard, construction plasters, portland cement setting agent, and agricultural gypsum are manufactured. Gypsum is quarried from the Miocene age Fish Creek Gypsum. Evaporite minerals were deposited in a clastic-rich sabkha environment along the margin of a small embayment in the Salton Trough. The Salton Trough is a major regional structure that formed by rifting and transform faulting along the Elsinore, San Jacinto, and San Andreas fault zones. Sedimentary basins were formed between tilted fault blocks. The basins were filled by prograding alluvial fans, basin margin sabkha and marine sediments, and deltaic deposits from the Colorado River. Gypsum is exposed in the quarry on rounded hills with 250-300 feet of relief. The evaporites are up to 200 feet thick and average 125 feet in thickness. Anhydrite commonly occurs in the lower part of the evaporites under the crests of hills and beneath thick alluvial cover.

Jan 1, 1995

By Robert R. McDougal, Anne E. McCafferty, Bruce D. Smith

Magnetic, electromagnetic, and radiometric airborne survey data have been used in regional and local (drainage basin) scales. In a regional geoenvironmental assessment of the state of Montana, magnetic and radiometric data compiled from airborne surveys were used along with other digital geologic and geochemical data to prioritize mining districts for potential acid water generation. Probability ratio mapping was done in order to integrate the interpretation of many different digital data sets. On a more local scale, the Animas (CO) and Boulder Basin (MT) watersheds have been studied using helicopter geophysical surveys. The airborne geophysical surveys show many more structural features than the geologic maps. Combined interpretation of the geophysical data sets using the probability ratio method has resulted in identification of areas of alteration. Airborne radiometric data in the Boulder Basin area suggests that rocks with high potassium and thorium also have a high acid water buffering capacity.

Jan 1, 2000

By Allan T. Fisk, Carl R. Peterson, Robert G. Lundquist

A long recognized goal in high speed tunneling and mining has been the development of a continuous drill and blast excavation capability. Both the advance rate and the economy of drill and blast tunneling can be significantly improved if the conventional cyclic process can be carried out continuously. Obviously, any continuous drill and blast tunneling machine must be an "all function" device, performing drilling, explosive loading, initiation, mucking, ventilation, roof support (if necessary), and perhaps other functions, essentially simultaneously, while remaining at the face throughout. Furthermore, such a machine must do all these things under remote control. THE SPIRAL BLAST PATTERN Several continuous drill and blast tunneling concepts have been proposed. Of these the Rapidex spiral blast pattern, taking advantage of a partially self-shielding geometry, seems to require the least shielding and hence offers the maximum access for mucking, although from the outset it was clear that remote mucking would present a major design challenge. The Rapidex continuous spiral blast concept uses an unusual blasting pattern that, under the geological conditions tested, has proven to be an effective and efficient means of fragmentation. The concept has a self-shielding characteristic which permits a lightly shielded machine to remain at the face during blasting. The pattern produces a spirally proceeding tunnel face, much like one turn of an auger. The leading portion of the spiral surface is connected to the trailing portion by an axially extending plane surface or bench. The ideal geometry is illustrated in Figure 1 for a horseshoe tunnel section.

Jan 1, 1979

By Dwight R. Coles

The solving of complex metallurgical flowsheet calculations by hand is, at best, a tedious job which often proves that engineers, too, make mistakes. The high cost and long lead time associated with manual flowsheet solutions have led several organizations involved in research, development and construction of extractive metallurgical processes to search for computerized systems which will solve flowsheet calculations. Although design flowsheet programs have been developed by the chemical industry, the ability to solve flowsheets involving particulate solids is usually overlooked. A new computer applications system has been developed at Fluor Mining and Metals which has been designed to accommodate the type of design flowsheets required by the minerals industry. By employing the sequential modular computation technique, a library of metallurgical pro- cessing routines may' be accumulated which are used by a universal executive system. This technique enables rapid solution of new process) .flow- sheets with only a minimum of additional programming effort. The implementation of the FLEXMET flowsheet solution system is the subject of this paper. Some of the major features of the system which are examined include interactive input data handling, automated flowsheet calculation order arrangement, flexible accomodation of unit operations models and advanced management of recycle and specification control calculations.

Jan 1, 1982

By David K. Parrish, Duane A. Labreche

Analyses of jointed, cracked, and fractured rock masses are needed in a variety of applications, including estimates of reduced elastic modulus for damaged rock, estimates of permeability changes as a function of stress changes, and estimates of relaxed regions due to excavation. A numerical model of a jointed rock mass, the compliant joint model, was used to study the response of a jointed rock mass near a circular excavation. The joint constitutive model was linear elastic in shear and nonlinear elastic in the relationship between normal stress and joint closure. Initial stresses were geostatic and representative of stresses in a granitic jointed rock mass approximately 300 m deep. The joint properties were based on values that are representative of joints in granite. The results from numerical simulations were compared with analytical results for stress near a circular opening in an elastic medium having reduced Young's Moduli to simulate jointing effects on the rock mass. The differences in response between the two models resulted from the differences in the symmetry of elastic properties, the shear modulus of the continua, and the constitutive relations in the two models. For example, the non- linear anisotropic elastic continuum described by the compliant joint model resulted in vertical stress concentrations near the side of the circular opening that were 25 percent higher than the vertical stress concentrations in an isotropic linear elastic medium. The equivalent Young's Moduli in the vertical and horizontal directions of the compliant joint continuum deviated by as much as 50 percent from the values assigned to the modeled region prior to excavations. The perturbations of the elastic Young's Moduli extended to distances of two to three radii from the opening.

Jan 1, 1986

By Kenneth S. Johnson

Oklahoma is a region of complex geology where a mobile belt of Paleozoic geosynclines and uplifts on the south abuts against the margin of the North American craton to the north. The state contains many classic areas where fundamental concepts of sedimentation, stratigraphy, structural geology, historical geology, mineral investigation, and petroleum exploration have been formulated through the years. In the southern Oklahoma mountain belts, there are exposed a great variety of igneous and sedimentary rock units seen at few other places in the Midcontinent area. Major geologic provinces of Oklahoma (Fig. 1) include: (1) the cratonic and relatively stable northern shelf areas, including the Ozark uplift; (2) the Ouachita geosyncline (now the Ouachita Mountain belt) and associated Arkoma basin in the southeast; and (3) the southern Oklahoma aulacogen (geosyncline), comprising the area of Anadarko, Ardmore, Marietta, and Hollis basins, as well as the Arbuckle and Wichita Mountain uplifts. The three principal fold belts, the Ouachitas, Arbuckles, and Wichitas, all originated from a series of Pennsylvanian orogenies (about 300 million years ago) in the two Paleozoic geosynclines.

Jan 1, 1999

By E. T. Sugar

English China Clays, the world's largest producer of China Clay, has its main production capacity in the South-West of England, where a complex of pits, refining plants, dryers and ports covers an area of approximately 100 square kilometres. The possibility of a computerised information network was first considered in 1980. The system was required to provide information at the central level and also at local plant level to improve co-ordination and control. Immediate access by any authorised user, and flexibility of interrogation were important aims. A small micro-based prototype system was implemented in 1981, and later that year development of the mainframe system commenced. This latter system will provide at least one terminal in every works location and will allow inter-communication of laboratory test data as well as detailed stock levels and production data. An integrated system for order processing will allow stock levels to be monitored in relation to anticipated requirements. The system has been developed by the Data Processing Department using the IDMS database package running on an ICL ME29 mainframe. It was decided to use microcomputers as terminals, which although more complicated because of protocol emulation allows stand-alone applications to be run on the same equipment. Those applications concerning Production Planning are outlined in the paper. Communication on the network is by synchronous transmission over dedicated lines. All data is stored on the central database with terminals accessing it in a star configuration. The system is currently partially implemented with 30 available screens at 18 separate worksites.

Jan 1, 1986

By S. P. Banerjee

By international standards, Indian coal seams are not very gassy. In some of the major coalfields such as Singareni, Wardha, Pench, Chirimiri, Rewa and Talcher Coalfields practically no methane is emitted from the coal seams. Even in the coalfields of Ranigang, Jharia, Bokaro and Karanpura, all of which are situated in the basin of the Damodar river, only a few mines are faced with excessive gas emission problems. But the number of such mines is increasing as deeper reserves are being worked and already the exploitation of some of the best quality coal reserves in the country is held up pending measures for control of methane emission in these mines. Even in mines having no previous history of gas emission, methane has been met near dykes and faults. This was dramatically revealed by an explosion in Dhori colliery in 1965 wherein 268 persons got killed. Until that time, Dhori colliery was considered as a non-gassy mine but on that fateful day gas came to the workings through a freshly exposed fault plane. Similar incidences of ignition of firedamp in so-called non-gassy mines have also occured in the past, for example, in Chapui Khas and Samla Dalurband collieries, but the casualty figures were not as high. After the Dhori explosion, all Indian coal seams have been declared to be gassy, whether presence of methane is detected in the workings or not.

Jan 1, 1980

By R. V. Ramani, R. Bhaskar

Control of respirable dust in mines has been given paramount importance due to the health and safety implications associated with fine dust. Understanding the temporal and spatial behavior of dust has been recognized as essential for increasing the efficiencies of existing control techniques and for developing new control strategies. Mining-related studies in this area are, in general, limited. They are also mostly experimental. Some mathematical and computer analyses have been at-tempted. In this paper, first, a review of the mathematical studies performed in the last three decades in this area is presented. Second, a mathematical model for analyzing dust flow in mines is proposed. The model takes into account a number of factors affecting dust transport. It in¬corporates varying dust generation source strengths and dispersion, deposition, and coagulation of dust in mine airways. Finally, application areas for the model are discussed. A computer program based on the mathematical model has been developed. The program will output the dust concentration in the mine atmosphere as a function of time and distance from the source. The amount of dust deposited on the sides, roof, and floor of the airway is also determined.

Jan 1, 1987

By Mark L. Blanford, Roger M. Zimmerman

INTRODUCTION Volcanic tuffs on and adjacent to the Nevada Test Site (NTS) are being considered by the Department of Energy (DOE) for the possible geo- logic disposal of high-level radioactive wastes. The Nevada Nuclear Waste Storage Investigations (NNWSI) project was established in 1977 to evaluate such disposal. Sandia National Laboratories (SNL), one of the participants in the NNWSI project, has as one of its responsibilities the development of a rock mechanics program for the Nevada site. SNL conducted three small-diameter heater experiments in welded and nonwelded tuffs in G-Tunnel on the NTS, to investigate the thermal (heat transfer) and hydrothermal (thermal- induced water migration) behavior as part of the rock mechanics program. These two aspects were investigated to increase knowledge about the behavior of tuff so that predictive capabilities are available for use by repository designers, waste-package designers, and performance analysts. Also, knowledge of the behavior of the tuff is invaluable for planning and designing future in situ experiments at Yucca Mountain, the candidate site for the repository. The evaluations of these three experiments is the subject of this paper. Designers, analysts, and experimenters are seeking a better understanding of the behavior of tuffs under the influence of thermal loads expected from radioactive-waste storage, because of two physical features peculiar to tuffs. First, tuffs are inherently porous because of the manner in which they are deposited (Smith, 1960). Tuffs utilized in G-Tunnel testing have porosities ranging from 15 to 46%, which cover the ranges of expected porosities in the target horizon at Yucca Mountain. It has been established that the G-Tunnel tuffs have similar bulk, thermal, and mechanical material properties to those at Yucca Mountain (Zimmerman et al., 1984), thus, G-Tunnel testing can be used to evaluate the effects of porosity on the thermal and mechanical behavior. The second feature is that tuffs above the water table contain pore water that influences the thermal properties of the rock; displacement of the water must be accounted for in repository designs and analyses. For example, G-Tunnel tuffs, located some 600 m above the static water level, have saturations in excess of 60%. Similar percentages are expected at the target horizon in Yucca Mountain (Zimmerman et al., 1984). The presence of and the removal of the pore water affects the thermal behavior of the tuffs, and these three experiments were designed first to determine the phenomenological behavior and then assess influences on predictive capabilities. The focus in this paper is to present the results and evaluations of the experiments as they apply to improving predictive capabilities. The thermal aspects are emphasized by comparing the measured temperatures (in and around heater emplacement holes) with calculations of predicted temperatures using numerical models, so that the effects of significant parameters can be evaluated and integrated into future predictive models. Observation of the hydrothermal aspects is needed to assess the effects of loss of pore water and subsequent migrations on the temperature fields during the heating, and also to define the expected environment in the vicinity of the outer metallic surface around the waste. The metallic boundary can be either the outer shell of the waste package system, which is the main engineered barrier for waste containment, or the borehole liner. A final decision has not been made as yet about the necessity for lining boreholes; thus, the emphasis is on predicting the characteristics of the environment around the outer metallic surface. Two aspects that limit the scope of this paper are (1) the experiments were performed at a smaller than canister scale for the purpose of

Jan 1, 1986

By P. Tsang, S. S. Peng

Mine floor failures, such as floor heave and floor buckling, occur frequently in underground coal mines where soft mine floor exists. The types of failure can usually be classified into two categories; shear punching failure and tensile failure. A model based on the Winkler's elastic foundation is proposed in this paper for floor stability analysis. The model considers material properties of floor strata, in-situ horizontal stress, pillar size, entry width, and configuration of multiple-entry system and predicts stress conditions in the mine floor based on given in-situ mining and geological conditions, as well as deformation of the mine floor. This information is used to predict possible failures of mine floor by comparing the strength of mine floor with its stress condition. The validity of the model is verified by in-situ data described in this paper.

Jan 1, 1992

By Harold D. Taylor

Cone fitting is a procedure which can be used to estimate the short range, linear portion of a variogram. Rather than combining data over windows In different directions and fitting by hand, cone fitting estimates the variogram in all directions at once using a multiple regression approach. The method automatically provides estimates of nugget effect, anisotropy, and initial slope of the variogram. This paper presents the results of simulation studies which have been carried out. These studies Indicate that the method works well and that it may be particularly useful for small data sets. The simulation studies also indicate that the local variogram may differ greatly from the theoretical variogram.

Jan 1, 1986

By S. P. Lucido, I. Iwasaki

The potential of controlling heavy metal ions in effluents from discontinued mining operations and waste rock piles has been investigated. A fresh water green alga, Cyanidium caldarium, was found to have the potential to remove Cut' from solutions while exhibiting high tolerance to acid conditions which are commonly encountered in copper-nickel mine drainage. The process has the potential for application as a low maintenance metal decontamination system. The growth requirements and copper removal characteristics of this microorganism are described.

Jan 1, 1991